首页 | 本学科首页   官方微博 | 高级检索  
     

基于地磁辅助的弹载两轴陀螺传感器校正方法研究
引用本文:鞠潭,于纪言,王晓鸣,顾晓辉. 基于地磁辅助的弹载两轴陀螺传感器校正方法研究[J]. 兵工学报, 2018, 39(10): 1919-1926. DOI: 10.3969/j.issn.1000-1093.2018.10.006
作者姓名:鞠潭  于纪言  王晓鸣  顾晓辉
作者单位:南京理工大学智能弹药技术国防重点学科实验室,江苏南京,210094;南京理工大学智能弹药技术国防重点学科实验室,江苏南京,210094;南京理工大学智能弹药技术国防重点学科实验室,江苏南京,210094;南京理工大学智能弹药技术国防重点学科实验室,江苏南京,210094
基金项目:国家自然科学基金项目(11402121)
摘    要:为解决弹载环境下两轴陀螺传感器难以实现三轴校正的问题,提出基于地磁辅助的两轴陀螺 传感器校正方法。建立两轴陀螺传感器测量误差模型,由单轴地磁信号解算得到弹丸x轴 角速率,解决了因陀螺传感器量程限制而无法测量低旋弹丸x轴滚转角速率的问题;研究线性最小二乘模型和卡尔曼滤波模型校正两轴陀螺传感器相关参数的方法,数值仿真分析弹丸x轴角速率解算误差和陀螺传感器测量噪声对校正结果的影响;半实物仿真模拟两轴陀螺传感器在工程中的应用,研究基于地磁辅助的两轴陀螺传感器校正方法校正效果。数值仿真结果表明:当弹丸x轴 角速率解算误差在0.261 8 rad/s以内且当陀螺传感器测量噪声在0.001 6 rad/s以内时,经过校正后,弹丸y轴和z轴角速率校正误差在0.01 rad/s以内。半实物仿真结果表明:当弹丸x轴角速率解算误差在0.8 rad/s以内时,两种校正模型均能将陀螺传感器的测量误差从-0.30~-0.05 rad/s范 围减小到-0.02~0.02 rad/s范围内。数值仿真和半实物仿真结果证明:基于地磁辅助的两轴陀螺传感器校正方法具有较好的校正效果。

关 键 词:微型旋转弹丸  弹丸姿态测量  陀螺传感器校正  地磁
收稿时间:2017-11-23

A Calibration Method of Magnetometer-aided Two-axis Gyro Sensor in the Projectile-borne Environment
JU Tan,YU Ji-yan,WANG Xiao-ming,GU Xiao-hui. A Calibration Method of Magnetometer-aided Two-axis Gyro Sensor in the Projectile-borne Environment[J]. Acta Armamentarii, 2018, 39(10): 1919-1926. DOI: 10.3969/j.issn.1000-1093.2018.10.006
Authors:JU Tan  YU Ji-yan  WANG Xiao-ming  GU Xiao-hui
Affiliation:(Ministerial Key Laboratory of ZNDY, Nanjing University of Science and Technology, Nanjing 210094, Jiangsu, China)
Abstract:A calibration method of magnetometer-aided two-axis gyro sensor is studied for the three-axis calibration of two-axis gyro sensor in the projectile-borne environment. A measurement error model of two-axis gyro sensor is established, and the problem that the roll angular rate of low spinning projectile at x-axis, which is obtained from the single-axis geomagnetic signal, cannot be measured by the gyro sensor due to its limited measurement range is solved. The calibration methods of the linear least square model and the Kalman filter model for calculating the related parameters of two-axis gyro sensor are studied, and the influences of the calculation error of x-axis angular rate of projectile and the measurement noise of gyroscope sensor on the calibrated result are analyzed through numerical simulation. The application of two-axis gyro sensor in engineering is simulated, and the correction effect of calibration method of magnetometer-aided two-axis gyro sensor is studied in the hardware-in-the-loop simulation. The numerically simulated results prove that,when the calculated error of x-axis angular rate of projectile is within 0.261 8 rad/s and the measured noise of gyro sensor is within 0.001 6 rad/s, the corrected errors of the y-axis and z-axis angular rates of projectile are less than 0.01 rad/s. The results of the hardware-in-the-loop simulation show that the two correction models can decrease the measured error range of gyro sensor from -0.30- -0.05 rad/s to -0.02-0.02 rad/s when the calculated error of x-axis angular rate of the projectile is within 0.8 rad/s. The numerical simulation and the hardware-in-the-loop simulation prove that the magnetometer-aided calibration method has a good correction effect on the two-axis gyro sensor.
Keywords:micro spinning projectile   attitude measurement   gyro sensor calibration   magnetism  
本文献已被 万方数据 等数据库收录!
点击此处可从《兵工学报》浏览原始摘要信息
点击此处可从《兵工学报》下载全文
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号