首页 | 本学科首页   官方微博 | 高级检索  
     

碳酸钠溶液吸收硫化氢富液的直接电解工艺
引用本文:田建勋,祁贵生,刘有智,高璟,付加,郭强,董梅英. 碳酸钠溶液吸收硫化氢富液的直接电解工艺[J]. 化工进展, 2015, 34(2): 325-329. DOI: 10.16085/j.issn.1000-6613.2015.02.005
作者姓名:田建勋  祁贵生  刘有智  高璟  付加  郭强  董梅英
作者单位:1. 中北大学山西省超重力化工工程技术研究中心, 山西 太原 030051;2. 超重力化工过程山西省重点实验室, 山西 太原 030051
基金项目:国家自然科学基金,山西省科技攻关计划(工业)(20130321035-02)项目。
摘    要:在电解碳酸钠吸收硫化氢的富液过程中,为了降低阳极钝化,提高负二价硫向零价硫的转化率和电流效率,采用板框式电解槽直接电解法回收硫黄和氢气,其中石墨电极为阳极,碳酸钠溶液吸收硫化氢富液为阳极液,钛网电极为阴极,氢氧化钠溶液为阴极液。实验考察了温度、pH值、初始溶液浓度、电流密度等因素对电解过程阳极反应的影响。结果表明:溶液中S2-的转化率随温度和初始溶液中Na2S浓度的增大而增大,而随电流密度的增大而降低。确定了适宜的电解条件为电解温度75℃,初始硫化钠溶液浓度在0.5mol/L以上,电流密度10~20mA/cm2,且初始阳极液中不加氢氧化钠为佳,此时阳极液中S2-的转化率可达85%以上。对回收硫黄的XRD、SEM表征结果表明,所生成的硫黄以斜方硫的形式存在,且硫黄颗粒粒径变大,有利于固液分离。

关 键 词:电解  硫化氢  吸收  氧化  硫化物  
收稿时间:2014-07-07

Direct electrolysis of H2S-loaded sodium carbonate solution
TIAN Jianxun,QI Guisheng,LIU Youzhi,GAO Jing,FU Jia,GUO Qiang,DONG Meiying. Direct electrolysis of H2S-loaded sodium carbonate solution[J]. Chemical Industry and Engineering Progress, 2015, 34(2): 325-329. DOI: 10.16085/j.issn.1000-6613.2015.02.005
Authors:TIAN Jianxun  QI Guisheng  LIU Youzhi  GAO Jing  FU Jia  GUO Qiang  DONG Meiying
Affiliation:1. Research Center of Shanxi Province for High Gravity Chemical Engineering and Technology, North University of China, Taiyuan 030051, Shanxi, China;2. Shanxi Province Key Laboratory of Higee-Oriented Chemical Engineering, Taiyuan 030051, Shanxi, China
Abstract:In order to restrain the anode passivation and increase the conversion ratio and current efficiency of sulfide to sulfur during the electrolysis of H2S-loaded sodium carbonate solution, direct electrolysis method by a filter press electrolyzer was used to recycle sulfur and hydrogen. Graphite was used as anode,and H2S-loaded sodium carbonate solution as anolytes;Titanium mesh was used as cathode and sodium hydroxide solution as catholytes. The effects of some parameters on anodic reactions were investigated,such as temperature,pH,initial concentration and current density. Results indicated that the conversion ratio of sulfide increased with the increase of initial sulfide concentration,but decreased with the increase of current density. Moreover,the appropriate electrolytic conditions were at temperature of 75℃,initial sulfide concentration above 0.5mol/L,current density of 10-20mA/cm2,and no sodium hydroxide addition into anolytes. Under the above conditions,the conversion ratio of sulfide could exceed 85%. The characterization of recovered sulfur with XRD and SEM methods showed that the produced sulfur was rhombi with bigger particle diameter,which was favorable in solid-liquid separation.
Keywords:electrolysis  hydrogen sulfide  absorption  oxidation  sulfide
本文献已被 CNKI 万方数据 等数据库收录!
点击此处可从《化工进展》浏览原始摘要信息
点击此处可从《化工进展》下载全文
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号