|
|||||
|
|
| 灰铸铁不同合金化同等强度下的加工性能对比研究 | |
| 引用本文： | 肖丽丽,任凤章,李锋军,张旦闻,吴锐,孙娟,王宇飞.灰铸铁不同合金化同等强度下的加工性能对比研究[J].铸造技术,2012,33(5):512-515. |
| 作者姓名： | 肖丽丽 任凤章 李锋军 张旦闻 吴锐 孙娟 王宇飞 |
| 作者单位： | 1. 河南科技大学材料科学与工程学院,河南洛阳,471003 2. 中国一拖集团有限公司工艺材料研究所,河南洛阳,471004 3. 洛阳理工学院机电工程系,河南洛阳,471023 |
| 基金项目： | 河南省科技创新人才计划项目(104100510005);河南省高校科技创新人才支持计划项目(2009HASTIT023);洛阳市应用技术研究与开发基金项目(0901011A) |
| 摘 要： | 制备了用多元合金添加剂(含RE、Cr、Mn、Si、Fe)合金化和Cu合金化的具有相同抗拉强度的2种灰铸铁,对比研究了2种灰铸铁的加工性能.结果表明,具有同强度的2种灰铸铁的布氏硬度和珠光体基体硬度基本相同,但多元合金添加剂合金化灰铸铁的断面敏感性较小,加工性能好,在切削深度分别为1.5、1.75、2.0mm的条件下,其主切削力比Cu合金化灰铸铁的分别降低了23.0％、55.0％和55.2％. |
| 关 键 词： | 灰铸铁 合金化 切削加工性能 强度 |
Comparative on the Machinability of Two Alloying Gray Cast Irons with Equal Tensile Strength |
|
| XIAO Li-li , REN Feng-zhang , LI Feng-jun , ZHANG Dan-wen , WU Rui , SUN Juan , WANG Yu-fei.Comparative on the Machinability of Two Alloying Gray Cast Irons with Equal Tensile Strength[J].Foundry Technology,2012,33(5):512-515. | |
| Authors: | XIAO Li-li REN Feng-zhang LI Feng-jun ZHANG Dan-wen WU Rui SUN Juan WANG Yu-fei |
| Affiliation: | 1(1.School of Materials Science and Engineering,Henan University of Science and Technology,Luoyang 471003,China;2.Institute of Materials and Technology,China Yituo Group Corporation Limited,Luoyang 471004,China;3.Department of Mechanical and Electrical Engineering,Luoyang Institute of Science and Technology,Luoyang 471023,China) |
| Abstract: | Two gray cast irons with equal tensile strength were prepared.They were inoculated using 75SiFe inoculant and were respectively alloyed using an alloying additive(including RE,Cr,Mn,Si and Fe elements) and pure copper.The machinability of the two gray cast irons was mainly investigated.The results show that the Brinell hardness of the two irons and the micro-hardness of their pearlite microstructure are same.The Section sensitivity of the iron alloyed using an alloying additive is smaller than that of the iron alloyed using pure copper.The main cutting forces of the iron alloyed using an alloying additive are 23%、55% and 55.2% decrease as compared with that of the iron using pure copper at the corresponding cutting depth 1.5 mm,1.75 mm and 2.0 mm. |
| Keywords: | gray cast iron alloy machinability tensile strength |
| 本文献已被 CNKI 万方数据 等数据库收录！ | |