| FM全新卡车内饰顶棚把手气辅注射成型的模拟分析 |
| |
| 引用本文： | 陈立恒,梁继才,李义,隋忠祥,张景民,徐立晶.FM全新卡车内饰顶棚把手气辅注射成型的模拟分析[J].吉林大学学报(工学版),2005,35(1):52-55. |
| |
| 作者姓名： | 陈立恒 梁继才 李义 隋忠祥 张景民 徐立晶 |
| |
| 作者单位： | 1. 吉林大学,材料科学与工程学院,吉林,长春,130022
2. 吉林大学,辊锻工艺研究所,吉林,长春,130022 |
| |
| 基金项目： | 国家科技攻关项目(2004BA907A19-2)，吉林省科技厅自然科学基金资助项目(20020614). |
| |
| 摘 要： | 利用Moldflow软件对FM全新卡车内饰顶棚把手的传统注射成型工艺和气体辅助注射成型工艺进行了分析．研究了熔体温度、注射时间、浇口位置对传统注射成型和气辅注射成型过程的影响以及熔体的预注射量、气体注射压力对气辅注射成型填充过程的影响。结果表明：采用气体辅助注射成型工艺熔体适宜的注入量为94％，可以节省原材料6％，熔体的注射压力降低了52．8％，锁模力下降了66．6％。
|
| 关 键 词： | 材料合成与加工工艺 Moldflow 气体辅助注射成型 模拟分析 |
| 文章编号： | 1671-5497(2005)01-0052-04 |
| 修稿时间： | 2004年7月21日 |
Simulation of gas-assisted injection molding for FM truck roof handle |
| |
| CHEN Liheng,LIANG Jicai,LI Yi,SUI Zhongxiang,ZHANG Jingmin,XU Lijing.Simulation of gas-assisted injection molding for FM truck roof handle[J].Journal of Jilin University:Eng and Technol Ed,2005,35(1):52-55. |
| |
| Authors: | CHEN Liheng LIANG Jicai LI Yi SUI Zhongxiang ZHANG Jingmin XU Lijing |
| |
| Affiliation: | CHEN Liheng~1,LIANG Jicai~1,LI Yi~2,SUI Zhongxiang~1,ZHANG Jingmin~2,XU Lijing~1 |
| |
| Abstract: | The conventional injection molding and gas-assisted injection molding(GAIM) processings for the FM truck roof handle were analyzed by means of the software Moldflow . The influences of melt temperature, injection time and gate location were studied. In addition, the influences of injection shot and gas pressure were also observed in GAIM. Simulation results showed that with appliation of GAIM, the optimum injection shot is 94%, therefore the 6% raw material can be saved, the injection pressure is decreased by 52.8% , and the clamp force is decreased by 66.6%. |
| |
| Keywords: | Material synthesize and manufacturing technics Moldflow gas-assisted injection molding simulation analysis |
| 本文献已被 CNKI 维普 万方数据 等数据库收录！ |
|
