基于ENC28J60的嵌入式网络接口的设计

设计了以ENC28J60为核心的以太网接口实现方案.描述了该系统硬件架构的设计方法.在简要介绍了以太网控制器ENC28J60的结构、功能、外围电路的基础上,对ENC28J60与Atmega16的SPI通讯进行了阐述.此方案不仅成本低,而且可以实现500Kbps以上的传输速率,满足了嵌入式系统的Internet控制要求.     

烟气在线分析数据远程传输

用单片机P89LPC938通过串口监听烟气在线分析系统数据,再通过SPI接口与以太网控制器ENC28J60通信,构成简易的WebServer,实现网络远程查看实时数据的功能。     

基于ENC424J600的以太网与串行接口转换技术

论述了在STM32系列的MCU上移植TCP/IP协议栈LwIP,并利用新型以太网控制器ENC424J600实现网络数据传输功能。该系统主要完成的功能是接收上位机发送的数据,并将这些数据转换成通用串行接口输出。ENC424J600是Microchip新推出的一款以太网控制器,其速度优于ENC28J60,同时为用户提供两种接口模式。本文介绍了其基于SPI接口模式下的实现过程,详细描述了该网卡驱动的硬件电路和软件流程。     

基于51主控的IP电话设计

介绍一种基于51单片机作为主控IP电话的系统设计。系统具有开发周期短,成本低等特点;主要采用AudioCodes的AC48801语音包处理器和Microchip的ENC28J60以太网控制器。AC48801支持厂家提供的多种语音编码器,不用另外进行算法开发,提供HPI接口,用一般的51单片机即可对其进行控制。ENC28J60内置10Mbps以太网物理层器件及媒介接入控制器,提供SPI接口与主控制芯片相连。     

嵌入式系统网络接口模块设计

嵌入式系统已广泛应用于网络中,所以需要相应的网络接口满足需求,介绍了设计此系统网络接口模块所需要的核心以太网控制器ENC28J60,分析了其工作机理,通过设置ENC28J60内部寄存器来完成数据的有效接收和发送,采用高速高性能的LPC2132微控制器与以太网控制器ENC28J60和接口芯片MAX232相连接实现网络接口模块设计,对接口电路作了详细阐述,并对系统控制软件进行了具体分析。该模块用途广泛,具有良好的应用前景。     

SPI接口以太网控制器ENC28J60及其应用

目前大多数以太网控制器都是为个人计算机而设计的,在精简的嵌入式系统中使用比较繁杂,常常需要采用扩展总线的方式,本文介绍了全球目前最小封装的以太网控制器ENC28J60,由于采用SPI串行接口方式,简化了设计,本文介绍了其特性、内部结构和引脚功能,详细分析了其寄存器设置和工作过程,给出了与微控制器接口的应用电路。     

基于ENC28J60的表面肌电信号采集系统的网络接口设计

针对当前许多医疗仪器未能实现网络连接的问题,提出了一种基于ENC28 J60的网络接口的设计方法,并应用于表面肌电信号采集系统。电路主要由主控芯片dsPIC30F6012和以太网控制芯片ENC28 J60组成。重点介绍了网络通信接口电路的设计、SPI通信,以及TCP/IP远程通信。实验证明,基于ECN28 J60的网络接口应用于表面肌电采集系统,具有结构简单、性能稳定、兼容性强的特点。     

基于STM32的热水器控制器与网络接口设计

针对太阳能热水器的智能化控制和网络监控功能进行了研究并提出设计方案,给出了整机原理图,完成了以STM32F103芯片为核心的测控电路及各接口电路的设计,选用ENC28J60以太网控制器定时上传数据,为实现局域网功能做好准备。控制器具有良好的人机交互功能及初步智能化特征。     

STM32F103VET6和ENC28J60的嵌入式以太网接口设计

介绍了一种基于STM32F103VET6微处理器和以太网控制芯片ENC28J60的嵌入式以太网接口的设计方案。分析了基于Cortex-M3内核的微处理器STM32F103VET6的功能和特点,以及以太网控制芯片ENC28J60的主要性能和结构特性,并给出了接口的硬件和软件设计方案。本接口尺寸小、性能高,适合于便携式仪器仪表中的应用。     

高速列车空气动力学试验以太网接口设计

针对高速列车上空气动力学试验布线复杂,易受干扰等问题,提出了分布式以太网检测系统,并设计了一个嵌入式以太网接口,采用ENC28J60作为以太网控制器和ARM Cortex-M3内核的STM32作为主控制器,移植了RT-Thread嵌入式系统以及LwIP协议栈,并建立了基于TCP的应用程序,实现了与上位机的高速以太网通信。经过测试,该以太网接口稳定可靠,满足高速列车空气动力学试验的要求。     

Only connect: teaching, technology and telesis

Abstract This paper describes an approach to the design of interactive multimedia materials being developed in a European Community project. The developmental process is seen as a dialogue between technologists and teachers. This dialogue is often problematic because of the differences in training, experience and culture between them. Conditions needed for fruitful dialogue are described and the generic model for learning design used in the project is explained.     

European Community policy and the market

Abstract This paper starts with some reflections on the policy considerations and priorities which are shaping European Commission (EC) research programmes. Then it attempts to position the current projects which seek to capitalise on information and communications technologies for learning in relation to these priorities and the apparent realities of the marketplace. It concludes that while there are grounds to be optimistic about the contribution EC programmes can make to the efficiency and standard of education and training, they are still too technology driven.     

一种自适应子融合集成多分类器方法

融合集成方法已经广泛应用在模式识别领域,然而一些基分类器实时性能稳定性较差,导致多分类器融合性能差,针对上述问题本文提出了一种新的基于多分类器的子融合集成分类器系统。该方法考虑在度量层融合层次之上通过对各类基多分类器进行动态选择,票数最多的类别作为融合系统中对特征向量识别的类别,构成一种新的自适应子融合集成分类器方法。实验表明,该方法比传统的分类器以及分类融合方法识别准确率明显更高,具有更好的鲁棒性。     

煤矿井下安全监控分站的设计及其仿真实现

为了设计一种具有低成本、低功耗、易操作、功能强且可靠性高的煤矿井下安全分站,针对煤矿安全生产实际,文章提出了采用MCS-51系列单片机为核心、具有CAN总线通信接口的煤矿井下安全监控分站的设计方案;首先给出煤矿井下安全监控分站的整体构架设计,然后着重阐述模拟量输入信号处理系统的设计过程,最后说明单片机最小系统及其键盘、显示、报警、通信等各个组成部分的设计;为验证设计方案的可行性与有效性,使用Proteus软件对设计内容进行仿真验证,设计的煤矿井下安全监控分站具有瓦斯、温度等模拟量参数超标报警功能和电机开停、风门开闭等开关量指示功能;仿真结果表明:设计的煤矿井下安全监控分站具有一定的实际应用价值.     

Avoiding semantic and temporal gaps in developing software intensive systems

Development of software intensive systems (systems) in practice involves a series of self-contained phases for the lifecycle of a system. Semantic and temporal gaps, which occur among phases and among developer disciplines within and across phases, hinder the ongoing development of a system because of the interdependencies among phases and among disciplines. Such gaps are magnified among systems that are developed at different times by different development teams, which may limit reuse of artifacts of systems development and interoperability among the systems. This article discusses such gaps and a systems development process for avoiding them.     

基于QTE的蒙古文显示机制研究与实现

蒙古语言是中国蒙古族使用的通用语言,由于蒙古文区别于其他文字的书写方式和其自身变形机制等特点,在很多通用的文字处理引擎中都不被支持。在嵌入式产品开发与应用领域中Linux加QTE已经成为流行方式。该文给出了一种在QTE环境上实现基于标准Unicode的蒙古文点阵显示和变形算法, 并自定义了支持蒙古文的QTE组件,扩展了QTE功能,为在Linux加QTE方式的嵌入式体系结构中处理蒙古文提供了一种解决方法。     

Designing economic np control charts: A programmed simulation approach

This paper presents control charts models and the necessary simulation software for the location of economic values of the control parameters. The simulation program is written in FORTRAN, requires only 10K of main storage, and can run on most mini and micro computers. Two models are presented - one describes the process when it is operating at full capacity and the other when the process is operating under capacity. The models allow the product quality to deteriorate to a further level before an existing out-of-control state is detected, and they can also be used in situations where no prior knowledge exists of the out-of-control causes and the resulting proportion defectives.     

基于AD9626的模拟信号采集存储卡设计

自然界的绝大部分信号都是以模拟的形式存在,因此模拟信号的采集转换存储在数字时代十分关键。文章讨论了在雷达信号处理领域基于AD9626的AD采集存储卡的设计原理、硬件结构和程序设计与芯片配置等问题,为今后相关领域的研究提供了可参考的方案。     

The development of robot art

Going through a few examples of robot artists who are recognized worldwide, we try to analyze the deepest meaning of what is called “robot art” and the related art field definition. We also try to highlight its well-marked borders, such as kinetic sculptures, kinetic art, cyber art, and cyberpunk. A brief excursion into the importance of the context, the message, and its semiotics is also provided, case by case, together with a few hints on the history of this discipline in the light of an artistic perspective. Therefore, the aim of this article is to try to summarize the main characteristics that might classify robot art as a unique and innovative discipline, and to track down some of the principles by which a robotic artifact can or cannot be considered an art piece in terms of social, cultural, and strictly artistic interest. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

A human-computer interface for non-computer specialists

The COM teleconferencing system was designed to be easy to use for both beginners and people with much computer experience. A number of design choices in organizing the human-computer interface were considered very carefully. These design problems are not unique for teleconferencing applications, but will appear in many other developments of human-computer interfaces for non-computer specialists. This report discusses naming conventions, menu format, user commands, help facility and the treatment of ‘type ahead’ from the users.