The effect of compatibilizers and organically modified nanoclay on the morphology and performance properties of poly(acrylonitrile–butadiene–styrene)/polypropylene blends

In this study, poly(acrylonitrile–butadiene–styrene)/polypropylene (ABS/PP) blends with various compositions were prepared by melt intercalation in a twin‐screw extruder. Modifications of the above blends were performed by using organically modified montmorillonite (OMMT, Cloisite 30B) reinforcement as well as two types of compatibilizers, namely polypropylene grafted with maleic anhydride (PP‐g‐MAH) and ABS grafted with maleic anhydride (ABS‐g‐MAH). Increasing the PP content in ABS matrix seems to increase the melt flow and thermal stability of their blends, whereas a deterioration of the tensile properties was recorded. On the other hand, the addition of ABS to PP promotes the formation of the β‐crystalline phase, which became maximum at 30 wt% ABS concentration, and increases the crystallization temperature (T_c) of PP. A tendency for increase of T_c was also recorded by incorporation of the above compatibilizers, whereas the glass transition temperature (T_g) of PP and SAN phase in ABS was reduced. Regarding the Young's modulus, the greatest improvement was observed in pure ABS/PP blends containing organically modified nanoclay. However, in reinforced pure PP, the use of compatibilizers is recommended in order to improve the elastic modulus. The addition of OMMT to noncompatibilized and compatibilized ABS/PP blends significantly improves their storage modulus. POLYM. ENG. SCI., 56:458–468, 2016. © 2016 Society of Plastics Engineers     

Nonisothermal crystallization and melting behavior of β‐nucleated isotactic polypropylene and polyamide 66 blends

A highly novel nano‐CaCO₃ supported β‐nucleating agent was employed to prepare β‐nucleated isotactic polypropylene (iPP) blend with polyamide (PA) 66, β‐nucleated iPP/PA66 blend, as well as its compatibilized version with maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted polyethylene‐octene (POE‐g‐MA), and polyethylene‐vinyl acetate (EVA‐g‐MA), respectively. Nonisothermal crystallization behavior and melting characteristics of β‐nucleated iPP and its blends were investigated by differential scanning calorimeter and wide angle X‐ray diffraction. Experimental results indicated that the crystallization temperature (T) of PP shifts to high temperature in the non‐nucleated PP/PA66 blends because of the α‐nucleating effect of PA66. T of PP and the β‐crystal content (K_β) in β‐nucleated iPP/PA66 blends not only depended on the PA66 content, but also on the compatibilizer type. Addition of PP‐g‐MA and POE‐g‐MA into β‐nucleated iPP/PA66 blends increased the β‐crystal content; however, EVA‐g‐MA is not benefit for the formation of β‐crystal in the compatibilized β‐nucleated iPP/PA66 blend. It can be relative to the different interfacial interactions between PP and compatibilizers. The nonisothermal crystallization kinetics of PP in the blends was evaluated by Mo's method. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Study of phenyl‐terminated hyperbranched polyester as a special β‐nucleating agent on the toughness of isotactic polypropylene

The effect of phenyl‐terminated hyperbranched polyester (HBP‐Bz) with different generation (the first generation and the fourth generation) as a special β‐nucleating agent on the toughness of isotactic polypropylene (iPP) was investigated by dynamic rheological measurements, scanning electron microscopy, differential scanning calorimetry, wide‐angle X‐ray diffraction, polarized optical microscopy, and mechanical properties measurements. The results show that the β nucleating activity of HBP‐Bz significantly depends on its concentration and molecular structure. The relative content of β‐crystal form (K_β) increases with the increasing HBP‐Bz percentage reaches a maximum and then decreases as HBP‐Bz percentage further increases. The K_β values of iPP/HBP‐G1‐1% and iPP/HBP‐G4‐1% blends are 26.52% and 20.80%, respectively. When compared with HBP‐G4, HBP‐G1 has incompact molecular structure, facilitating the π–π interaction between phenyl‐terminated groups and the helix chains of iPP crystallize on it, and therefore relatively good dispersibility, high β nucleating activity and excellent toughening effect are obtained. The impact strength of iPP was dramatically improved, especially with addition of 1 wt% HBP‐G1. POLYM. ENG. SCI., 59:E133–E143, 2019. © 2018 Society of Plastics Engineers     

Compatibilization of polypropylene/Poly(acrylonitrile‐butadiene‐styrene) blends by polypropylene‐graft‐cardanol

The polypropylene‐graft‐cardanol (PP‐g‐cardanol) was prepared by reactive extrusion with polypropylene (PP) and natural renewable cardanol which could increase the interfacial energy of PP and inhibit the degradation of PP during the process of reactive extrusion and usage. In this article, PP‐g‐cardanol and polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) were used as compatibilizers of the polypropylene (PP)/poly(acrylonitrile‐butadiene‐styrene) (ABS) blends. PP/ABS (70/30, wt %) blends with PP‐g‐cardanol and PP‐g‐MAH were prepared by a corotating twin‐screw extruder. From the results of morphological studies, the droplet size of ABS was minimized to 1.93 and 2.01 μm when the content of PP‐g‐cardanol and PP‐g‐MAH up to 5 and 7 phr, respectively. The results of mechanical testing showed that the tensile strength, impact strength and flexural strength of PP/ABS (70/30) blends increase with the increasing of PP‐g‐cardanol content up to 5 phr. The complex viscosity of PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol showed the highest value. Moreover, the change of impact strength and tensile strength of PP/ABS (70/30) blends were investigated by accelerated degradation testing. After 4 accelerated degradation cycles, the impact strength of the PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol decrease less than 6%, but PP/ABS (70/30) blends with 5 phr PP‐g‐MAH and without compatibilizer decrease as much as 12% and 32%, respectively. The tensile strength of PP/ABS (70/30) blends has a similar tendency to that of impact strength. The above results indicated that PP‐g‐cardanol could be used as an impact modifier and a good compatibilizer, which also exhibited better stability performance during accelerated degradation testing. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41315.     

Isothermal crystallization and melting behavior of polypropylene with lanthanum complex of cyclodextrin derivative as a β‐nucleating agent

A novel highly active β‐nucleating agent, β‐cyclodextrin complex with lanthanum (β‐CD‐MAH‐La), was introduced to isotactic polypropylene (iPP). Its influence on isothermal crystallization and melting behavior of iPP was investigated by differential scanning calorimeter (DSC), wide‐angle X‐ray diffraction (WAXD), and polarized light microscopy (PLM). WAXD results demonstrated that β‐CD‐MAH‐La was an effective β‐nucleating agent, with β‐crystal content of iPP being strongly influenced by the content of β‐CD‐MAH‐La and the isothermal crystallization temperature. The isothermal crystallization kinetics of pure iPP and iPP/β‐CD‐MAH‐La was described appropriately by Avrami equation, and results revealed that β‐CD‐MAH‐La promoted heterogeneous nucleation and accelerated the crystallization of iPP. In addition, the equilibrium melting temperature (T) of samples was determined using linear and nonlinear Hoffman‐Weeks procedure. Finally, the Lauritzen‐Hoffman secondary nucleation theory was applied to calculate the nucleation parameter (K_g) and the fold surface energy (σ_e), the value of which verify that the addition of β‐CD‐MAH‐La reduced the creation of new surface for β‐crystal and then led to faster crystallization rate. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Dynamically cured polypropylene/epoxy blends

The dynamic vulcanization process, usually used for the preparation of thermoplastic elastomers, was used to prepare polypropylene (PP)/epoxy blends. The blends had crosslinked epoxy resin particles finely dispersed in the PP matrix, and they were called dynamically cured PP/epoxy blends. Maleic anhydride grafted polypropylene (MAH‐g‐PP) was used as a compatibilizer. The effects of the reactive compatibilization and dynamic cure were studied with rheometry, capillary rheometry, and scanning electron microscopy (SEM). The crystallization behavior and mechanical properties of PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends were also investigated. The increase in the torque at equilibrium for the PP/MAH‐g‐PP/epoxy blends indicated the reaction between maleic anhydride groups of MAH‐g‐PP and the epoxy resin. The torque at equilibrium of the dynamically cured PP/epoxy blends increased with increasing epoxy resin content. Capillary rheological measurements also showed that the addition of MAH‐g‐PP or an increasing epoxy resin content increased the viscosity of PP/epoxy blends. SEM micrographs indicated that the PP/epoxy blends compatibilized with PP/MAH‐g‐PP had finer domains and more obscure boundaries than the PP/epoxy blends. A shift of the crystallization peak to a higher temperature for all the PP/epoxy blends indicated that uncured and cured epoxy resin particles in the blends could act as effective nucleating agents. The spherulites of pure PP were larger than those of PP in the PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends, as measured by polarized optical microscopy. The dynamically cured PP/epoxy blends had better mechanical properties than the PP/epoxy and PP/MAH‐g‐PP/epoxy blends. With increasing epoxy resin content, the flexural modulus of all the blends increased significantly, and the impact strength and tensile strength increased slightly, whereas the elongation at break decreased dramatically. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1437–1448, 2004     

Polypropylene–intumescent flame‐retardant composites based on meleated polypropylene as a coupling agent

The phosphoric acid‐pentaerythritol‐melamine copolymer, which is composed of three main components of intumescent flame retardant (IFR) and has optimal intumescent degree, was selected as IFR. The influence of meleated polypropylene (PP‐g‐MAH) on the properties and compatibility of IFR polypropylene (PP) composites were studied. The results obtained from mechanical tests, rheological behavior of composites, and scanning electron microscope showed that PP‐g‐MAH was a true coupling agent for IFR/PP blends and did not change the necessary flame retardancy. The cocrystallization between bulk PP and PP segments of PP‐g‐MAH was also proven by WAXD analysis. Flow test showed that the flow behaviors of composites in the melt are those of a pseudoplastic and it is very small for PP‐g‐MAH affecting rheological behavior of the PP/IFR composite. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 257–262, 2002     

Toughening of PP/EPDM blend by compatibilization

To improve the mechanical properties of blends of polypropylene (PP) and terpolymer of ethylene–propylene–diene (EPDM), a triblock copolymer, (PP‐g‐MAH)‐co‐[PA‐6,6]‐co‐(EPDM‐g‐MAH), was synthesized by coupling reaction of maleic anhydride (MAH)‐grafted PP (PP‐g‐MAH), EPDM‐g‐MAH, and PA‐6,6. The newly prepared block copolymer brought about a physical interlocking between the blend components, and imparted a compatibilizing effect to the blends. Introducing the block copolymer to the blends up to 5 wt % lead to formation of a β‐form crystal. The wide‐angle X‐ray diffractograms measured in the region of 2θ between 10° and 50° ascertained that incorporating the block copolymer gave a new peak at 2θ = 15.8°. The new peak was assigned to the (300) plane spacings of the β‐hexagonal crystal structure. In addition, the block copolymer notably improved the low‐temperature impact property of the PP/EPDM blends. The optimum usage level of the compatibilizer proved to be 0.5 wt %. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1267–1274, 2000     

Preparation and properties of dynamically cured PP/MAH‐g‐EVA/epoxy blends

A method concerning with the simultaneous reinforcing and toughening of polypropylene (PP) was reported. Dynamical cure of the epoxy resin with 2‐ethylene‐4‐methane‐imidazole (EMI‐2,4) was successfully applied in the PP/maleic anhydride‐grafted ethylene‐vinyl acetate copolymer (MAH‐g‐EVA), and the obtained blends named as dynamically cured PP/MAH‐g‐EVA/epoxy blends. The stiffness and toughness of the blends are in a good balance, and the smaller size of epoxy particle in the PP/MAH‐g‐EVA/epoxy blends shows that MAH‐g‐EVA was also used as a compatibilizer. The structure of the dynamically cured PP/MAH‐g‐EVA/epoxy blends is the embedding of the epoxy particles by the MAH‐g‐EVA. The cured epoxy particles as organic filler increases the stiffness of the PP/MAH‐g‐EVA blends, and the improvement in the toughness is attributed to the embedded structure. The tensile strength and flexural modulus of the blends increase with increasing the epoxy resin content, and the impact strength reaches a maximum of 258 J/m at the epoxy resin content of 10 wt %. DSC analysis shows that the epoxy particles in the dynamically cured PP/MAH‐g‐EVA/epoxy blends could have contained embedded MAH‐g‐EVA, decreasing the nucleating effect of the epoxy resin. Thermogravimetric results show the addition of epoxy resin could improve the thermal stability of PP, the dynamically cured PP/MAH‐g‐EVA/epoxy stability compared with the pure PP. Wide‐angle x‐ray diffraction analysis shows that the dynamical cure and compatibilization do not disturb the crystalline structure of PP in the blends. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Dynamically cured polypropylene/Novolac blends compatibilized with maleic anhydride‐g‐polypropylene

In this article, the dynamic vulcanization process was applied to polypropylene (PP)/Novolac blends compatibilized with maleic anhydride‐grafted PP (MAH‐g‐PP). The influences of dynamic cure, content of MAH‐g‐PP, Novolac, and curing agent on mechanical properties of the PP/Novolac blends were investigated. The results showed that the dynamically cured PP/MAH‐g‐PP/Novolac blend had the best mechanical properties among all PP/Novolac blends. The dynamic cure of Novolac improved the modulus and stiffness of the PP/Novolac blends. The addition of MAH‐g‐PP into dynamically cured PP/Novolac blend further enhanced the mechanical properties. With increasing Novolac content, tensile strength, flexural modulus, and flexural strength increased significantly, while the elongation at break dramatically deceased. Those blends with hexamethylenetetramine (HMTA) as a curing agent had good mechanical properties at HMTA content of 10 wt %. Scanning electron microscopy (SEM) analysis showed that dynamically cured PP/MAH‐g‐PP/Novolac blends had finer domains than the PP/MAH‐g‐PP/Novolac blends. Thermogravimetric analysis (TGA) results indicated that the incorporation of Novolac into PP could improve the thermal stability of PP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

The effect of graft copolymers of maleic anhydride and epoxy resin on the mechanical properties and morphology of PP/ABS blends

In this work, maleic anhydride‐grafted polypropylene (PP‐g‐MAH) and maleic anhydride‐grafted poly(acrylonitrile‐butadiene‐styrene) (ABS‐g‐MAH) at 2 : 1 mass ratio were added as a compatibilizer in the PP/ABS blends. The compatibilizing effect was evaluated by adding the graft copolymers together with epoxy resin/imidazole curing agent (E51/2E4MZ). The reaction in reactive extrusion, morphological structure, and properties of PP and ABS blends were investigated by using infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X‐ray spectrum, transmission electron microscope (TEM), dynamic thermomechanical analysis (DMA), differential scanning calorimetry (DSC), and mechanical properties tests. The results showed that the compatibilizing effect was greatly improved because of the addition of the graft copolymers together with epoxy resin/imidazole curing agent (E51/2E4MZ) because the link structure of PP‐g‐MAH and ABS‐g‐MAH was formed by the reaction of anhydride group with epoxy group catalyzed by the imidazole. The size of the dispersed phase decreased dramatically, the interfacial adhesion between ABS particles and PP matrix was improved, and the tensile strength and flexural modulus of the PP/ABS blends increased further. The optimizing properties were obtained at 3 phr E51/2E4MZ. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40898.     

Effect of polystyrenes with different architectures on the β‐nucleating efficiency and toughening of isotactic polypropylene

The effect of polystyrenes (PSs) with different architectures (three‐arm star‐shaped polystyrene (sPS), comb‐like branched polystyrene (cPS) and linear polystyrene) on their β‐nucleating efficiency for isotactic polypropylene (iPP) during crystallization and final impact and the tensile properties of iPP/PS blends were investigated by dynamic rheological measurements, SEM, DSC, polarized optical microscopy, wide angle X‐ray diffraction and mechanical property measurements. The results show that the architecture of PS has marked influence on its dispersibility in iPP and β‐nucleating efficiency. For iPP/cPS blend, plenty of short side chains reduce the probability of cPS chain entanglements, facilitating the interdiffusion between iPP and cPS chains. A favorable interfacial interaction results in good dispersibility, high β nucleating efficiency and an excellent toughening effect of cPS on iPP. However, the relatively high chain entanglement degree of sPS may not be in favor of chain diffusion between iPP and sPS and therefore relatively poor dispersibility and toughening effect are obtained. The elongation at break and impact strength of iPP were dramatically improved, especially with the addition of 1 wt% cPS. The toughening mechanism of PS on iPP is the dissipated energy caused by cavitation and the β‐nucleating effect of PS. © 2018 Society of Chemical Industry     

Investigation on β‐polypropylene/PP‐g‐MAH/ surface‐treated calcium carbonate composites

β‐Polypropylene composites containing calcium carbonate treated by titanate coupling agent (T‐CaCO₃) and maleic anhydride grafted PP (PP‐g‐MAH) were prepared by melt compounding. The crystallization, morphology and mechanical properties of the composites were investigated by means of differential scanning calorimetry, wide‐angle X‐ray diffraction, polarized light microscopy, scanning electron microscopy and mechanical tests. It is found that both T‐CaCO₃ and NT‐C are able to induce the formation of β‐phase, and NT‐C greatly increases the β content and decreases the spherulitic size of PP. PP‐g‐MAH facilitates the formation of β‐form PP and improves the compatibility between T‐CaCO₃ and PP. Izod notched impact strength of β‐PP/T‐CaCO₃ composite is higher than that of PP/T‐CaCO₃ composite, indicating the synergistic toughening effect of T‐CaCO₃ and β‐PP. Incorporation of PP‐g‐MAH into β‐PP/T‐CaCO₃ composite further increases the content of β‐crystal PP and improves the impact strength and tensile strength when T‐CaCO₃ concentration is below 5 wt%. The nonisothermal crystallization kinetics of β‐PP composites is well described by Jeziorny's and Mo's methods. It is found that NT‐C and T‐CaCO₃ accelerate the crystallization rate of PP but the influence of PP‐g‐MAH on crystallization rate of β‐PP composite is marginal. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Greatly improved toughness of isotactic polypropylene blends with traces of carbon nanotubes

In this work, the β‐nucleated isotactic polypropylene (iPP)/ ethylene‐octene copolymer (POE) blends demonstrated greatly enhanced impact toughness by adding traces of carbon nanotubes (CNTs) (only 0.05 wt%). When the POE content was 30 wt%, the impact strength of β‐nucleated iPP/POE blends with CNTs was as high as 51.7 kJ/m², about 5.6 kJ/m² higher than β‐nucleated iPP/POE blends, 15.2 kJ/m² higher than CNTs‐filled iPP/POE blends, and almost 19 times of pure iPP sample. This significantly improved impact toughness was considered to be attributed to the shear yielding and multiple‐crazing, originating from the presence of abundant β‐crystals in the iPP matrix, the enhanced mobility of the molecular chains in the confined amorphous region of iPP lamellae and the homogenous distribution of POE dispersed phase with a small size, indicating the synergistic effect of CNTs, β‐nucleating agent and POE on the toughness of iPP. POLYM. ENG. SCI., 59:757–764, 2019. © 2018 Society of Plastics Engineers     

Polypropylene/polypropylene‐grafted acrylic acid copolymer/ethylene–Acrylic acid copolymer ternary blends for hydrophilic polypropylene

Ternary blends of polypropylene (PP), a polypropylene‐grafted acrylic acid copolymer (PP‐g‐AA), and an ethylene–acrylic acid copolymer (EAA) were prepared by melt blending. The surfaces of films with different contents of these three components were characterized with contact‐angle measurements. Scanning electron microscopy, Fourier transform infrared spectroscopy, differential scanning calorimetry, and thermogravimetric analysis were used to characterize the microstructure, melting and crystalline behavior, and thermal stability of the blends. The contact angles of the PP/PP‐g‐AA blends decreased monotonically with increasing PP‐g‐AA content. With the incorporation of EAA, the contact angles of the PP/PP‐g‐AA/EAA ternary blends decreased with increasing EAA content. When the concentration of EAA was higher than 15 wt %, the contact angles of the ternary blends began to increase. Scanning electron microscopy observations confirmed that PP‐g‐AA acted as a compatibilizer and improved the compatibility between PP and EAA in the ternary blends. Differential scanning calorimetry analysis suggested that acrylic acid moieties could act as nucleating agents for PP in the polymer blends. Thermogravimetric analysis and differential thermogravimetry confirmed the optimal blend ratio for the PP/PP‐g‐AA/EAA ternary blends was 70/15/15. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 436–442, 2006     

A novel β‐nucleating agent for isotactic polypropylene

The nucleating ability of p‐cyclohexylamide carboxybenzene (β‐NA) towards isotactic polypropylene (iPP) was investigated by differential scanning calorimetry, X‐ray diffraction, polarized optical microscopy and scanning electron microscopy. β‐NA is identified to have dual nucleating ability for α‐iPP and β‐iPP under appropriate kinetic conditions. The formation of β‐iPP is dependent on the content of β‐NA. The content of β‐phase can reach as high as 96.96% with the addition of only 0.05 wt% β‐NA. Under non‐isothermal crystallization the content of β‐iPP increases with increasing cooling rate. The maximum β‐crystal content is obtained at a cooling rate of 40 °C min^–1. The supermolecular structure of the β‐iPP is identified as a leaf‐like transcrystalline structure with an ordered lamellae arrangement perpendicular to the special surface of β‐NA. Under isothermal crystallization β‐crystals can be formed in the temperature range 80–140 °C. The content of β‐crystals reaches its maximum value at a crystallization temperature of 130 °C. © 2012 Society of Chemical Industry     

Compatibilization of polypropylene/ poly(3‐hydroxybutyrate) blends

Blending polypropylene (PP) with biodegradable poly(3‐hydroxybutyrate) (PHB) can be a nice alternative to minimize the disposal problem of PP and the intrinsic brittleness that restricts PHB applications. However, to achieve acceptable engineering properties, the blend needs to be compatibilized because of the immiscibility between PP and PHB. In this work, PP/PHB blends were prepared with different types of copolymers as possible compatibilizers: poly(propylene‐g‐maleic anhydride) (PP–MAH), poly (ethylene‐co‐methyl acrylate) [P(E–MA)], poly(ethylene‐co‐glycidyl methacrylate) [P(E–GMA)], and poly(ethylene‐co‐methyl acrylate‐co‐glycidyl methacrylate) [P(E–MA–GMA)]. The effect of each copolymer on the morphology and mechanical properties of the blends was investigated. The results show that the compatibilizers efficiency decreased in this order: P(E–MA–GMA) > P(E–MA) > P(E–GMA) > PP–MAH; we explained this by taking into consideration the affinity degree of the compatibilizers with the PP matrix, the compatibilizers properties, and their ability to provide physical and/or reactive compatibilization with PHB. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of different β‐nucleating agent on crystallization behavior,morphology, and melting characteristic of multiwalled carbon nanotube‐filled isotactic polypropylene nanocomposites

To obtain isotactic polypropylene (iPP) nanocomposites with high β‐crystal content, TMB5, calcium pimelate and calcium pimelate supported on the surface of nano‐CaCO₃ were used as β‐nucleating agent and MWCNT filled β‐nucleated iPP nanocomposites were prepared. The effect of different β‐nucleating agent and MWCNT on the crystallization behavior and morphology, melting characteristic and β‐crystal content of β‐nucleated iPP nanocomposites were investigated by DSC, XRD and POM. The results indicated that addition of MWCNT increased the crystallization temperature of iPP and MWCNT filled iPP nanocomposites mainly formed α‐crystal. The β‐nucleating agent can induce the formation of β‐crystal in MWCNT filled iPP nanocomposites. The β‐nucleating ability and β‐crystal content in MWCNT filled β‐nucleated iPP nanocomposites decreased with increasing MWCNT content and increased with increasing β‐nucleating agent content due to the nucleation competition between MWCNT and β‐nucleating agents. It is found that the calcium pimelate supported on the surface of inorganic particles as β‐nucleating agent has stronger heterogeneous β‐nucleation than calcium pimelate and TMB5. The MWCNT filled iPP nanocomposites with high β‐crystal content can be obtained by supported β‐nucleating agent. POLYM. COMPOS., 36:635–643, 2015. © 2014 Society of Plastics Engineers     

Effect of the compatibilizer on the morphology and properties of dynamically cured PP/POE/epoxy blends

Dynamic vulcanization was successfully applied to epoxy resin reinforced polypropylene (PP)/ethylene‐octene copolymer (POE) blends, and the effects of different compatibilizers on the morphology and properties of dynamically cured PP/POE/epoxy blends were studied. The results show that dynamically cured PP/POE/epoxy blends compatibilized with maleic anhydride‐grafted polypropylene (MAH‐g‐PP) have a three‐phase structure consisting of POE and epoxy particles dispersed in the PP continuous phase, and these blends had improved tensile strength and flexural modulus. While using maleic anhydride‐grafted POE (MAH‐g‐POE) as a compatibilizer, the structure of the core‐shell complex phase and the PP continuous phase showed that epoxy particles could be embedded in MAH‐g‐POE in the blends, and gave rise to an increase in impact strength, while retaining a certain strength and modulus. DSC analysis showed that the epoxy particles in the blends compatibilized with MAH‐g‐PP were more efficient nucleating agents for PP than they were in the blends compatibilized with MAH‐g‐POE. WAXD analysis shows that compatibilization do not disturb the crystalline structure of PP in the blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Melting and crystallization behaviors,morphology, and mechanical properties of β‐polypropylene/polypropylene‐graft‐maleic anhydride/calcium sulfate whisker composites

The melting and crystallization behaviors, morphology, and mechanical properties of polypropylene (PP)/surface‐treated calcium sulfate (CaSO₄) whisker (T‐CSW), β‐PP/T‐CSW, and β‐PP/polypropylene‐graft‐maleic anhydride (PP‐g‐MAH)/T‐CSW composites had been investigated via differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), polarized light microscopy (PLM), scanning electron microscopy (SEM), and mechanical tests. We found that T‐CSW was an α‐nucleating agent and increased the crystallization temperatures of PP, but PP‐g‐MAH and high loadings of T‐CSW had weakly negative effects on the crystallization rates of PP. The T‐CSW restrained the formation of β‐spherulites, and the spherulitic size decreased in the composites. PP‐g‐MAH improved the compatibility and adhesion between T‐CSW and the matrix. The notched impact strength was improved, and the tensile strength was enhanced at low levels of T‐CSW, while the flexural modulus was weakened for β‐PP/T‐CSW and β‐PP/PP‐g‐MAH/T‐CSW composites versus PP/T‐CSW composites. POLYM. COMPOS., 37:2121–2132, 2016. © 2015 Society of Plastics Engineers