水平微细圆管内R290流动沸腾流态可视化研究

本文对水平微细圆管内R290流动沸腾的流态进行了可视化研究，分析不同管径下流动沸腾换热主要流态形式及影响因素，基于理论流态图对比分析流态转变规律。实验工况：热流密度1～70 kW/m²,质量流率50～1 020 kg/(m²·s),饱和温度-10～25℃,管径1～3 mm,干度0～1。实验中共观察到8种R290微细通道内流动沸腾换热流态，其中间歇流和波状流为3 mm管的主要换热流态，弹状流和环状为1 mm管的主要换热流态；实测流态图中3 mm管的泡状流、混状流，2 mm管的泡状流，1 mm管的弹状流与D&W流态转变准则较为吻合，而2 mm管和1 mm管的离散流区域匹配性较差；管径的变化对流态有重要影响，随着管径的减小，气泡形状、流态形式、流态分布及流态转变曲线均发生变化，管径微尺度效应出现。     

R410A微通道内沸腾换热实验研究

在内径为2 mm的水平不锈钢微通道内对R410A的沸腾换热特性进行了实验研究。质量流率为200~600 kg/(m2·s),热流密度的范围为5~15 k W/m2,干度的范围为0.1~0.8,饱和温度为0℃和5℃。结果显示,当干度大于0.5时,随着热流密度的上升,沸腾换热系数显著上升,其平均增幅分别达到了4.6%和7.7%。当干度小于0.5时,热流密度对换热系数的影响十分微弱。随着质量流率的上升,换热系数均出现了小幅上升,其平均增幅也分别达到了1.1%和2%。而饱和温度对换热系数则几乎没有影响。随后,对可能的机理进行了讨论。实验结果又与Choi K I等以及Ebisu T等在内径分别为1.5 mm,3 mm和6.4mm管道内的研究结果进行了比较。结果显示,在相似工况下,随着管径的下降,当干度小于0.5时,换热系数呈现出上升的趋势,其平均增幅分别达到了18.4%,23.6%和19.5%。     

R32在水平管内流动沸腾换热特性的试验研究

对R32在水平光滑管和微肋管(外径均为7mm)内的沸腾换热特性展开试验研究,测试的制冷剂质量流速为100~250 kg/(m~2·s),饱和蒸发温度为7~11℃,热流密度为3~8 kW/m~2,测试管内制冷工质平均干度值为0~0.7。试验结果表明:热流密度是影响R32沸腾换热系数的主导因素之一,质量流速的增大、饱和蒸发温度的升高、热流密度的增大均有利于提高R32的沸腾换热系数;微肋管有强化传热的效果,其平均沸腾换热系数比光管增大11.8%~33.2%;干度对R32沸腾换热系数的影响比较复杂,R32的沸腾换热系数随干度的增加先增大后减小,这是由于出现了干涸值,本文试验测得的干涸值范围为0.41~0.57,制冷剂质量流速的降低和热流密度的增大均有利于干涸值的增大。     

管径变化对蒸发器性能影响的仿真与实验研究

家用空调换热器采用的管径不同,产生的传热效果等性能有差异。采用空气焓差法,对具有相同制冷量的5 mm管径换热器和7 mm管径换热器进行了蒸发工况的实验,并建立了不同管径换热器的仿真计算模型,分析了管径的变化对蒸发器制冷剂侧和空气侧的换热和压降的影响。对比实验与计算结果,发现:1)5 mm换热器空气侧表面传热系数提高了17%;2)在相同制冷量下,5 mm换热器的制冷剂质量流量减少了4.6%,质量流速增大了89.4%,同时由于管壁热流密度的增大,引起了蒸干点的提前;3)以制冷剂达到相同干度时的换热系数作为基准,随着干度的增加,5 mm管的管内换热系数增大到7 mm管的1.43~1.86倍;同时制冷剂的摩擦压降、加速压降和局部压降均为7 mm换热器的3倍,压降引起了蒸发温度降低1.1℃。     

R290在水平微细圆管内沸腾换热特性研究

本文研究了R290在内径为1 mm、2 mm和4 mm水平微细圆管内的沸腾流动换热特性,在饱和温度为15℃条件下,质量流速为50～600 kg/(m~2·s)、干度为0～1、热流密度为5～20 k W/m~2时,对沸腾传热系数的影响进行了分析。通过实验发现,增大质量流速对传热系数具有增强作用,质量流速对传热系数的影响在低干度区域比高干度区域小。在热流密度方面,传热系数随着热流密度的增大而增大,且在1 mm和2 mm管内观察到了临界干度对传热系数的影响,这时传热系数有断崖式下降的趋势。在管径对于传热系数的影响方面,通过对不同管径换热特性的横向对比,发现在一定工况下传热系数随着管径的减小有所上升。此外本文还对R290已有的部分关联式进行了适配性验证。     

R32在小管径水平光管内的流动沸腾换热与压降特性试验研究

对R32在?5 mm的水平光管内的流动沸腾换热与压降特性进行试验研究和理论分析。试验的蒸发温度为5℃,质量流量范围为100~500 kg/(m2·s),热流密度为8~24 kW/m2。结果表明,沸腾换热系数在1~8 kW/(m2·K)之间,压降在1~4 kPa/m之间。沸腾换热系数随着干度增大而增大,质量流量的增大和热流密度的增大都有利于换热系数的增加。质量流量的变化对压降的影响比较明显。与R32在?7 mm管内流动传热性能相比,换热系数提高了30%左右。将得到的沸腾换热系数和压降试验数据与多个模型的预测结果进行比较,发现多数换热经验关联式的预测误差较大,仅有Fuji-Nagata关联式的预测值与试验值较为接近;压降的预测误差相对较小。     

多壁碳纳米管水基纳米流体的对流换热特性

实验研究了纳米粉体浓度、雷诺数Re和热流密度对多壁碳纳米管水基纳米流体(MWNTs/H2O)对流换热性能的影响。纳米粉体浓度分别为0.05 g/L、0.1 g/L、0.2 g/L和0.4 g/L,雷诺数Re为500~900,热流密度为10~20 k W/m2。结果表明:1)纳米流体对流换热系数随着纳米粉体浓度、Re、热流密度的增加而增加。如在Re为631且纳米粉体浓度为0.4 g/L时,纳米流体对流换热系数比基液增大了17.6%;2)纳米流体对流换热系数的提高率明显大于对应的导热系数提高率,当纳米粉体浓度为0.05g/L时,其对流换热系数和导热系数的提高率分别为7.4%和0.15%;3)在Eubank-Proctor方程的基础上,建立了适合于低Re条件下的混和对流换热的实验关联式。     

低流量下阵列式微通道对流沸腾特性实验研究

设计了阵列式微通道热沉结构,进行了并R134a的沸腾流动换热实验。结果证明,在低干度区域由泡状流/弹状流/半环状流主导,主导换热机理为对流沸腾和蒸发,热交换系数随热流密度显著增加,随质量流量增大而略有增加。在高干度区域搅拌流/束状流主导沸腾流动,对流蒸发为主导换热机理,换热系数随流量增大而增大。该结构可以在低流量下提前紊流转捩;有效抑制压力波动,减小进出口压力差。实验观察发现搅拌流/束状流型,气液界面波失稳导致液膜破碎和卷携。液滴沉积会润湿局部蒸干壁面。当热流持续增大,液膜破碎并大量被卷携入气核后,壁面附着气膜且无法被润湿,形成反束状流型时,触发CHF。     

微柱群通道内饱和沸腾换热特性实验研究

为实现微小空间高效散热,本文以去离子水为工质,实验研究了工质流经高度和直径均为500μm的微圆柱组成的叉排微柱群通道时的饱和沸腾换热特性,并采用高速摄像机记录了通道内不同加热功率的气液两相流型,实验参数设定质量流速为341~598.3 kg/(m~2·s),热流密度为20~160 W/cm~2,蒸气干度为0~0.2。结果表明:随着热流密度增大,局部沸腾换热表面传热系数近似单调递减。在低干度区,局部沸腾换热表面传热系数随着质量流速的增加而增大,随着蒸气干度的增加而减小;受过冷沸腾气泡影响,工质进口温度越低,局部沸腾换热表面传热系数越大;随着热流密度增大,微柱群通道流动沸腾气泡流型依次为:泡状流、环状流,且泡状流区的局部沸腾换热表面传热系数明显高于环状流区。     

微细管内CO2流动沸腾换热特性研究

针对CO2作为制冷剂在微细通道内流动沸腾换热进行了实验与理论研究,采用红外成像观测与换热系数实验研究定量与定性的分析了热流密度：2~35 kW/m2,饱和温度：﹣10 ℃ ~15 ℃工况时,内径为1 mm、2 mm圆管内的换热系数。实验结果表明：热流密度的增加强化了微细通道内工质核态沸腾换热,使换热系数得到显著提高;换热系数随饱和温度非单调变化,饱和温度较高时,越接近CO2临界温度其换热系数随饱和温度升高而增加,当饱和温度在低温工况时换热系数则随其降低而增加,换热过程中发生干涸干度随饱和温度升高而单调降低。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.