High-performance supercapacitor of manganese oxide/reduced graphene oxide nanocomposite coated on flexible carbon fiber paper

Although supercapacitors have higher power density than batteries, they are still limited by low energy density and low capacity retention. Here we report a high-performance supercapacitor electrode of manganese oxide/reduced graphene oxide nanocomposite coated on flexible carbon fiber paper (MnO₂–rGO/CFP). MnO₂–rGO nanocomposite was produced using a colloidal mixing of rGO nanosheets and 1.8 ± 0.2 nm MnO₂ nanoparticles. MnO₂–rGO nanocomposite was coated on CFP using a spray-coating technique. MnO₂–rGO/CFP exhibited ultrahigh specific capacitance and stability. The specific capacitance of MnO₂–rGO/CFP determined by a galvanostatic charge–discharge method at 0.1 A g⁻¹ is about 393 F g⁻¹, which is 1.6-, 2.2-, 2.5-, and 7.4-fold higher than those of MnO₂–GO/CFP, MnO₂/CFP, rGO/CFP, and GO/CFP, respectively. The capacity retention of MnO₂–rGO/CFP is over 98.5% of the original capacitance after 2000 cycles. This electrode has comparatively 6%, 11%, 13%, and 18% higher stability than MnO₂–GO/CFP, MnO₂/CFP, rGO/CFP, and GO/CFP, respectively. It is believed that the ultrahigh performance of MnO₂–rGO/CFP is possibly due to high conductivity of rGO, high active surface area of tiny MnO₂, and high porosity between each MnO₂–rGO nanosheet coated on porous CFP. An as-fabricated all-solid-state prototype MnO₂–rGO/CFP supercapacitor (2 × 14 cm) can spin up a 3 V motor for about 6 min.     

Ag nanoparticles anchored NiO/GO composites for enhanced capacitive performance

Hierarchical nickel oxide/graphene oxide (NiO/GO) and nickel oxide/graphene oxide/silver (NiO/GO/Ag) heterostructures were sucessfully fabricated as high-performance supercapacitors electrode materials by using a hydrothermal process and a photoreduction process. The experimental results showed that the NiO/GO/Ag heterostructure electrodes showed better electrochemical performance than those of NiO/GO and bare NiO nanosheets. The NiO/GO/Ag electrode exhibited a higher specific capacitance of 229 F g⁻¹ at a current density of 1 A g⁻¹, higher than that of 161 F g⁻¹ for NiO/GO composites. Furthermore, NiO/GO/Ag electrode also showed good rate capability (still 200 F g⁻¹ at 6 A g⁻¹) and cycling stability (24% loss after 2000 repetitive cycles at a scan rate of 20 mV s⁻¹). The enhanced capacitive performance of the NiO/GO/Ag composites was mainly attributed to the introduction of Ag nanoparticles, which increased the electrical conductivities of the composites, and promoted the electron transfer between the active components. This study suggested that NiO/GO/Ag composites were a promising class of electrode materials for high performance energy storage applications.     

Fabrication of manganese oxide/three-dimensional reduced graphene oxide composites as the supercapacitors by a reverse microemulsion method

Manganese oxide (MnO₂)/three-dimensional (3D) reduced graphene oxide (RGO) composites were prepared by a reverse microemulsion (water/oil) method. MnO₂ nanoparticles (3–20 nm in diameter) with different morphologies were produced and dispersed homogeneously on the macropore surfaces of the 3D RGO. Scanning electron microscopy and transmission electron microscopy were applied to characterize the microstructure of the composites. The MnO₂/3D RGO composites, which were annealed at 150 °C, displayed a significantly high specific capacitance of 709.8 F g⁻¹ at 0.2 A g⁻¹. After 1000 cycles, the capacitance retention was measured to be 97.6%, which indicates an excellent long-term stability of the MnO₂/3D RGO composites.     

Functionalized three-dimensional graphene networks for high performance supercapacitors

Three-dimensional (3D) thermal reduced graphene network (TRGN) deposition on Ni foam without any conductive agents and polymer binders was successfully synthesized by dipping Ni foam into graphene oxide (GO) suspension and subsequent thermal reduction process. The direct and close contact between thermal reduced graphene and Ni foam is beneficial to the enhanced conductivity of the electrode, as well as the improvement of ion diffusion/transport into the electrode. Additionally, low-temperature reduction of GO possesses a large amount of stable oxygen-containing groups that can provide high pseudocapacitance. As a result, the TRGN electrode delivers a high specific capacitance of 442.8 F g⁻¹ at 2 mV s⁻¹ in 6 mol L⁻¹ KOH. Moreover, symmetric supercapacitor based on TRGN exhibits a maximum energy density of 30.4 Wh kg⁻¹ based on the total mass of the two electrodes in 1 mol L⁻¹ Na₂SO₄ electrolyte, as well as excellent cycling stability with 118% of its initial capacitance after 5000 cycles.     

Hollow graphene spheres self-assembled from graphene oxide sheets by a one-step hydrothermal process

We developed a one-step hydrothermal method to assemble graphene oxide (GO) sheets into hollow graphene spheres (HGSs), using only a GO/H₂SO₄ aqueous suspension as the starting material. Scanning electron microscope, focused ion beam scanning electron microscope and transmission electron microscope images show that the as-prepared HGSs vary from 1 to 3 μm in diameter and have a hollow interior structure. The as-prepared HGSs show a high capacitance of 207 F g⁻¹, as well as good rate capability and cycling stability when used as electrode materials for supercapacitors.     

Simultaneous reduction,exfoliation, and nitrogen doping of graphene oxide via a hydrothermal reaction for energy storage electrode materials

Nitrogen (N)-doped graphene (NG) sheets were prepared using (NH₄)₂CO₃ and an aqueous dispersion of graphene oxide (GO) by an eco-friendly hydrothermal reaction. The in situ produced ammonia played an important role in the simultaneous nitrogen doping, the reduction and exfoliation of GO. The (NH₄)₂CO₃/GO mass ratio and reaction temperature were varied to investigate the effects on the N doping level. The elemental analysis determined from the X-ray photoelectron spectroscopy showed that the nitrogen content of the NG was about 10.1 at.% and the oxygen content decreased significantly due to the hydrothermal reduction of GO. The electrochemical performances of the NG sheets increased with increasing doped N content. The highest specific capacitance of 295 F g⁻¹ at a current density of 5 A g⁻¹ and the highest specific surface area of 412 m² g⁻¹ were observed with the sample processed at 130 °C. The retention of the specific capacitance was maintained at ∼89.8% after 5000 charge–discharge cycles. These results imply that NG sheets obtained by this simple eco-friendly approach are suitable for use in high performance energy storage electrode materials.     

Easy synthesis of porous graphene nanosheets and their use in supercapacitors

We report the easy synthesis of porous graphene nanosheets (PGNs) using the etching of graphene sheets by MnO₂. An electrode made from PGNs exhibits a specific capacitance of 154 F g^?1 at 500 mV s^?1 in 6 M KOH compared to a value of 67 F g^?1 for graphene nanosheets, and a low capacitance loss of 12% after 5000 cycles. Interestingly, PGN electrode material shows an excellent rate capability due to its open layered and mesopore structures that facilitate the efficient access of electrolytes to the electrode material and shorten the ion diffusion pathway through the porous sheets. This approach offers the potential for cost-effective, environmentally friendly and large-scale production of PGNs.     

Hydrothermal synthesis and activation of graphene-incorporated nitrogen-rich carbon composite for high-performance supercapacitors

Graphene-incorporated nitrogen-rich carbon composite with nitrogen content of ca. 10 wt.% has been synthesized by an effective yet simple hydrothermal reaction of glucosamine in the presence of graphene oxide (GO). The nitrogen content of carbon composite is nearly twice as high as that of hydrothermal carbon without graphene. GO is favorable for the high nitrogen doping in the carbon composite by the reaction between the glucosamine-released ammonia and GO. The hydrothermal carbon composite is further activated by KOH, and graphene in the activated carbon composite demonstrates a positive effect of increasing specific surface area, pore volume and electrical conductivity, resulting in superior electrochemical performance. The activated carbon composite with higher specific surface area and micropore volume possesses higher specific capacitance with a value of 300 F g⁻¹ at 0.1 A g⁻¹ in 6 M KOH aqueous solution in the two electrode cell. Larger mesopore volume and higher conductivity of the activated carbon composite will provide fast ion and electron transfer, thus leading to higher rate capacity with a capacitance retention of 76% at 8 A g⁻¹ in comparison to the activated hydrothermal carbon without graphene.     

High performance MnO2 nanoflower supercapacitor electrode by electrochemical recycling of spent batteries

MnO₂ nanoflower is prepared by electrochemical conversion of Mn₃O₄ obtained by heat treatment of spent zinc‒carbon batteries cathode powder. The heat treated and converted powders were characterized by TGA, XRD, FTIR, FESEM and TEM techniques. XRD analyses show formation of Mn₃O₄ and MnO₂ phases for the heat treated and converted powders, respectively. FESEM images indicate the formation of porous nanoflower structure of MnO_2, while, condensed aggregated particles are obtained for Mn₃O₄. The energy band gap of MnO₂ is obtained from UV‒Vis spectra to be 2.4 eV. The electrochemical properties are investigated using cyclic voltammetry, galvanostatic charge‒discharge and electrochemical impedance techniques using three-electrode system. The specific capacitance of MnO₂ nanoflower (309 F g⁻¹ at 0.1 A g⁻¹) is around six times higher than those obtained from the heat treated one (54 F g⁻¹ at 0.1 A g⁻¹). Moreover, it has high capacitance retention up to 93% over 1650 cycles. Impedance spectra of MnO₂ nanoflower show very small resistances and high electrochemical active surface area (340 m² g⁻¹). The present work demonstrates a novel electrochemical approach to recycle spent zinc-carbon batteries into high value supercapacitor electrode.     

Facile synthesis of sandwich-like polyaniline/boron-doped graphene nano hybrid for supercapacitors

The physicochemical property of chemically prepared graphene can be significantly changed due to the incorporating of heteroatoms into graphene. In this article, boron-doped graphene sheets are used as carbon substrates instead of graphene for loading polyaniline by in situ polymerization. Compared with the individual component and polyaniline/non-doped graphene, the sandwich-like polyaniline/boron-doped graphene exhibits remarkably enhanced electrochemical specific capacitance in both acid and alkaline electrolytes. In a three-electrode configuration, the hybrid has a specific capacitance about 406 F g⁻¹ in 1 M H₂SO₄ and 318 F g⁻¹ in 6 M KOH at 1 mV s⁻¹. In the two-electrode system of a symmetric supercapacitor, this hybrid achieves a specific capacitance about 241 and 189 F g⁻¹ at 0.5 A g⁻¹ with a specific energy density around 19.9 and 30.1 Wh kg⁻¹, in the acid and alkaline electrolytes, respectively. The as-obtained polyaniline/boron-doped graphene hybrid shows good rate performance. Notably, the obtained electrode materials exhibit long cycle stability in both acid and alkaline electrolytes (∼100% and 83% after 5000 cycles, respectively). The improved electrochemical performance of the hybrid is mainly attributed to the introduction of additional p-type carriers in carbon systems by boron-doping and the well combination of pseudocapacitive conducting polyaniline.     

The additive-free electrode based on the layered MnO2 nanoflowers/reduced,graphene oxide film for high performance supercapacitor

The MnO₂ nanoflowers/reduced graphene oxide composite is coated on a nickel foam substrate (denoted as MnO₂ NF/RGO @ Ni foam) via the layer by layer (LBL) self-assembly technology without any polymer additive, following the soft chemical reduction. The layered MnO₂ NF/RGO composite is uniformly anchored on the Ni foam skeleton to form the 3D porous framework, and the interlayers have access to lots of ions channels to improve the electron transfer and diffusion. This special construction of 3D porous structure is beneficial to the enhancement of electrochemical property. The specific capacitance is up to 246 F g⁻¹ under the current density of 0.5 A g⁻¹. After 1000 cycles, it can retain about 93%, exhibiting excellent cycle stability. The electrochemical impedance spectroscopy measurements confirm that MnO₂ NF/RGO @ Ni foam electrode has lower R_ESR and R_CT values when compared to MnO₂ @ Ni foam and RGO @ Ni foam. This study opens a new door to the preparation of composite electrodes for high performance supercapacitor.     

Construction of hierarchical NiMoO4@MnO2 nanosheet arrays on titanium mesh for supercapacitor electrodes

Hierarchical NiMoO₄@MnO₂ nanosheet arrays supported on titanium mesh are synthesized by cost effective hydrothermal methods for binder-free electrode. High specific area of porous MnO₂nanosheets and exceptionally high pseudocapacitive behavior of NiMoO₄nanosheets lead to a specific capacitance of 976 F g⁻¹at a current density of 1 A g⁻¹ with pleasurable rate characteristic in three electrode configuration. The excellent electrochemical performances of the integrated electrode can be ascribed to the unique core-shell nanostructure and synergic interaction. It is believed that the hierarchical NiMoO₄@MnO₂ nanosheet arrays supported on titanium mesh can provide great prospect for energy storage applications.     

Encapsulation of manganese oxides nanocrystals in electrospun carbon nanofibers as free-standing electrode for supercapacitors

Flexible composites with manganese oxides (MnO_x) nanocrystals encapsulated in electropun carbon nanofibers were successfully fabricated via a simple and practical combination of electrospinning and carbonization process. The as-formed MnO_x/carbon nanofibers composites have a rough surface with MnO_x nanoparticles well embedded in the carbon nanofibers backbones. When used as electrodes for supercapacitor, the resulting MnO_x/carbon nanofiber composites exhibit good electrochemical performance with a specific capacitance of 174.8 F g⁻¹ at 2 mV s⁻¹ in 0.5 M Na₂SO₄ electrolyte, a good rate capability at high current density and long-term cycling stability. It is expected that such freestanding composites could be promising electrodes for high-performance supercapacitors.     

Nanodiamond particles/reduced graphene oxide composites as efficient supercapacitor electrodes

The paper reports on the preparation of reduced graphene oxide (rGO) modified with nanodiamond particles composites by a simple solution phase and their use as efficient electrode in electrochemical supercapacitors. The technique relies on heating aqueous solutions of graphene oxide (GO) and nanodiamond particles (NDs) at different ratios at 100 °C for 48 h. The morphological properties, chemical composition and electrochemical behavior of the resulting rGO/NDs nanocomposites were investigated using UV/vis spectrometry, Fourier transform infrared (FTIR) spectroscopy, Raman spectroscopy, transmission electron microscopy (TEM) and electrochemical means. The electrochemical performance, including the capacitive behavior of the rGO/NDs composites were investigated by cyclic voltammetry and galvanostatic charge/discharge curves at 1 and 2 A g⁻¹ in 1 M H₂SO₄. The rGO/ND matrix with 10/1 ratio displayed the best performance with a specific capacitance of 186 ± 10 F g⁻¹ and excellent cycling stability.     

Graphene-wrapped polyaniline nanofibers as electrode materials for organic supercapacitors

Graphene-wrapped polyaniline nanofibers were prepared by assembly of negatively charged graphene oxide with positively charged aqueous dispersible polyaniline nanofibers in an aqueous dispersion, followed by the reduction of the graphene oxide. The hybrid material with a graphene oxide loading of 9.1 wt.% displayed a high specific capacitance of over 250 F g⁻¹ in a 1 M Et₄N⁺·BF₄⁻/propylene carbonate electrolyte, a 39.7% increase compared with pristine polyaniline nanofibers. A significant improvement in long-term cycle life was also realized. The hybrid exhibited an initial specific capacitance of 236 F g⁻¹, which remained as high as 173.3 F g⁻¹ over 1000 cycles, or a 26.3% decrease, much better than that for pure polyaniline nanofibers. An asymmetric supercapacitor based on this hybrid material and activated carbon was assembled. An energy density of 19.5 W h kg⁻¹ at a power density of 738.95 W kg⁻¹ was obtained for the cell under an operating voltage window of 2 V.     

Improved activity of a graphene–TiO2 hybrid electrode in an electrochemical supercapacitor

We present a simple and fast approach for the synthesis of a graphene–TiO₂ hybrid nanostructure using a microwave-assisted technique. The microstructure, composition, and morphology were characterized by X-ray diffraction, Fourier-transform infrared spectroscopy, Raman microscopy, X-ray photoelectron spectroscopy, and field-emission scanning electron microscopy. The electrochemical properties were evaluated using cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests. Structural analysis revealed a homogeneous distribution of nanosized TiO₂ particles on graphene nanosheets. The material exhibited a high specific capacitance of 165 F g⁻¹ at a scan rate of 5 mV s⁻¹ in 1 M Na₂SO₄ electrolyte solution. Theenhanced supercapacitance property of these materials could be ascribed to the increased conductivity of TiO₂ and better utilization of graphene. Moreover, the material exhibited long-term cycle stability, retaining ∼90% specific capacitance after 5000 cycles, which suggests that it has potential as an electrode material for high-performance electrochemical supercapacitors.     

Ultra-low-edge-defect graphene nanoribbons patterned by neutral beam

Top-down process, comprising lithography and plasma etching is widely used in very-large-scale integration due to its scalability, has the greatest potential to fabricate graphene nanoribbon based nanoelectronic devices for large-scale intergraded circuits. However, conventional plasma etching inevitably introduces plenty of damage or defects to the etched materials, which drastically degrades the performance of nano materials. In this study, extremely low-damage neutral beam etching (NBE) is applied to fabricate ultra-low-defect graphene nanoribbon array (GNR). The ultra-low-edge-defect GNRs are fabricated by E-beam lithography followed by oxygen NBE from large-scale chemical-vapor-deposition-grown graphene. AFM images clearly shows the GNRs patterned by NBE and E-beam lithography, and Raman spectroscopy exhibits extremely low I_D/I_G of GNRs, which indicate that high-quality GNRs can be successfully fabricated by neutral beam. We also demonstrated bottom-gated field-effect transistor with the high-quality GNR and observed a high carrier mobility (>200 cm² V⁻¹ s⁻¹) at room temperature.     

The composite material based on Dawson-type polyoxometalate and activated carbon as the supercapacitor electrode

A supercapacitor electrode assembled from activated carbon (AC) and (NH₄)₆[P₂Mo₁₈O₆₂]·14.2H₂O (P₂Mo₁₈) was fabricated for the first time, and showed remarkable electrochemical performance ascribed to the synergy of the double layer capacitance of AC and the pseudocapacitance of P₂Mo₁₈. The investigations indicate that the AC/P₂Mo₁₈ electrode exhibits a specific capacitance of 275 F g^− 1 at a high current density of 6 A g^− 1, which is substantially larger than the 182 F g^− 1 of the AC electrode. In addition, the AC/P₂Mo₁₈ electrode possesses a remarkable rate capability (89%) when the current density is increased from 2 to 6 A g^− 1.     

Template synthesis of hollow carbon spheres anchored on carbon nanotubes for high rate performance supercapacitors

A carbon material consisting of hollow carbon spheres anchored on the surface of carbon nanotubes (CNT–HCS) has been synthesized by an easy chemical vapor deposition process using a CNT–MnO₂ hybrid as template. An electrode made of this material exhibits a maximum specific capacitance of 201.5 F g⁻¹ at 0.5 A g⁻¹ and excellent rate performance (69% retention ratio at 20 A g⁻¹). It has impressive cycling stability with 90% initial capacitance retained after 5000 cycles at 5 A g⁻¹ in 6 mol L⁻¹ KOH. Symmetric supercapacitors based on CNT–HCS achieve a maximum energy density of 11.3 W h kg⁻¹ and power density of 11.8 kW kg⁻¹ operated within a wide potential range of 0–1.6 V in 1.0 mol L⁻¹ Na₂SO₄ solution.     

Decoration of carbon cloth by manganese oxides for flexible asymmetric supercapacitors

Here we describe the production of carbon cloth coated with MnO₂ nanosheets or MnOOH nanorods through a normal temperature reaction or a hydrothermal approach, respectively. Of note, the electrochemical performance of MnO₂-coated carbon cloth was better (429.2 F g⁻¹) than that of MnOOH-coated carbon cloth. When the MnO₂-coated carbon cloth is introduced as the positive electrode and the Fe₂O₃-coated carbon cloth as the negative electrode, a flexible asymmetric supercapacitor was obtained with an energy density of 22.8 Wh kg⁻¹ and a power density of 159.4 W kg⁻¹. Therefore, such a hierarchical MnO₂-coated carbon cloth nanocomposite is a promising high-performance electrode for flexible supercapacitors.