Hydrogen production from acid and enzymatic oat straw hydrolysates in an anaerobic sequencing batch reactor: Performance and microbial population analysis

Feasibility of hydrogen production from acid and enzymatic oat straw hydrolysates was evaluated in an anaerobic sequencing batch reactor at 35 °C and constant substrate concentration (5 g chemical oxygen demand/L). In a first experiment, hydrogen production was replaced by methane production. Selective pressures applied in a second experiment successfully prevented methane production. During this experiment, initial feeding with glucose/xylose, as model substrates, promoted biomass granulation. Also, the highest hydrogen molar yield (HMY, 2 mol H₂/mol sugar consumed) and hydrogen production rate (HPR, 278 mL H₂/L-h) were obtained with these model substrates. Gradual substitution of glucose/xylose by acid hydrolysate led to disaggregation of granules and lower HPR and HMY. When the model substrates were completely substituted by enzymatic hydrolysate, the HMY and HPR were 0.81 mol H₂/mol sugar consumed and 29.6 mL H₂/L-h, respectively. Molecular analysis revealed a low bacterial diversity in the stages with high hydrogen production and vice versa. Furthermore, Clostridium pasteurianum was identified as the most abundant species in stages with a high hydrogen production. Despite that feasibility of hydrogen production from hydrolysates was demonstrated, lower performance from hydrolysates than from model substrates was obtained.     

Aspect ratio effect of bioreactor on fermentative hydrogen production with immobilized sludge

The phenomenon of bacterial wash-out frequently occurs in the traditional continuous stirred tank reactor (CSTR) systems at low hydraulic retention time (HRT). In this study, the effect of different aspect ratios, height (H) to diameter (D) of 1:1, 3:1 and 5:1, of a CSTR with immobilized anaerobic sludge on hydrogen (H₂) production were investigated. The pH, volatile suspended solids (VSS) and total solids (TS) concentrations of the seed sludge were 6.8, 33.3 and 65.1 g/L, respectively. Thermally treated sludge was immobilized by silicone gel entrapment approach. The entrapped-sludge system operated stably at a low HRT without suffering from cell wash-out. Hence, the hydrogen production rate (HPR) was enhanced by increasing organic loading rates. The immobilized sludge CSTRs were operated at 40 °C with sucrose (10, 20, 30 and 40 g COD/L) and Endo nutrient medium at different HRTs (4, 2, 1 and 0.5 h). It was found that the granule formation enhanced HPR. The maximum HPR and the H₂ yield were found to be 15.36H₂ L/h/L and 3.16 mol H₂/mol sucrose, respectively, with the H₂ content in the biogas above 44% for all tests runs.     

Optimizing biohydrogen production from mushroom cultivation waste using anaerobic mixed cultures

The mushroom bag is a polypropylene bag stuffed with wood flour and bacterial nutrients. After being used for growing mushroom for one to two weeks this bag becomes mushroom cultivation waste (MCW). About 150 million bags (80,000 tons) of MCW are produced annually in Taiwan and are usually burned or discarded. The cellulosic materials and nutrients in MCW could be used as the feedstock and nutrients for anaerobic biohydrogen fermentation. This study aims to select the inoculum from various waste sludges (sewage sludge I, sewage sludge II, cow dung and pig slurry) with or without adding any extra nutrients. A batch test was operated at a MCW concentration of 20 g COD/L, temperature 55 °C and an initial cultivation pH of 8. The results show that extra nutrient addition inhibited hydrogen production rate (HPR) and hydrogen production yield (HY) when using cow dung and pig slurry seeds. However, nutrient addition enhanced the HPR and HY in case of using sewage sludge inoculum and without inoculum. This related to the inhibition caused by high nutrient concentration (such as nitrogen) in cow dung and pig slurry. Peak HY of 0.73 mmol H₂/g TVS was obtained with no inoculum and nutrient addition. However, peak HPR and specific hydrogen production rate (SHPR) of 10.11 mmol H₂/L/d and 2.02 mmol H₂/g VSS/d, respectively, were obtained by using cow dung inoculum without any extra nutrient addition.     

Biohydrogen production from palm oil mill effluent (POME) by two stage anaerobic sequencing batch reactor (ASBR) system for better utilization of carbon sources in POME

The production of biohydrogen through dark fermentation of palm oil mill effluent (POME) was evaluated in two-stages of biohydrogen in an anaerobic sequencing batch reactor (ASBR) system using enriched mixed culture for the first time. This study attempts to examine the effect of HRT and its interaction behavior with the solid retention time (SRT), and the sugar consumption. The effluent after discharged from the thermophilic reactor contained 7.61 g/L TC and 22.87 g/L TSS was fed to the secondary mesophilic reactor system. Results indicated that the overall sugar consumption reached 88.62% at the optimum HRT of 12 h with the SRT set to 20 h. The optimum hydrogen yield and HPR in the thermophilic stage were 2.99 mol H₂/mol-sugar and 8.54 mmol H₂/L·h respectively, while for the mesophilic stage were 1.19 mol H₂/mol-sugar and 1.47 mmolH₂/L·h respectively. The overall HPR showed an improvement and increase from 8.54 mmol H₂/L·h to 10.34 mmol H₂/L.h. Microbial community analysis of mixed culture in the two-stage thermophilic (55.0 °C) and mesophilic (37.0 °C) ASBR reactor was dominated by Thermoanaerobacterium sp. based on the PCR-DGGE technique.     

Non-sterile bio-hydrogen fermentation from food waste in a continuous stirred tank reactor (CSTR): Performance and population analysis

Bio-hydrogen production from food waste by anaerobic mixed cultures was conducted in a continuous stirred tank reactor (CSTR). The hydraulic retention time (HRT) was optimized in order to maximize hydrogen yield (HY) and hydrogen production rate (HPR). The maximum hydrogen content (38.6%), HPR (379 mL H₂/L. d) and HY (261 mL H₂/g-VS_added) were achieved at the optimum HRT of 60 h. The major soluble metabolite products were butyric and acetic acids which indicated a butyrate-acetate type fermentation. Operation of CSTR at HRT 60 h could select hydrogen producing bacteria and eliminate lactic acid bacteria and acetogenic bacteria. The microbial community analyzed by polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) revealed that the predominant hydrogen producer was Clostridium sp.     

Application of rice rhizosphere microflora for hydrogen production from apple pomace

The combination of substrate materials and bacteria is an important factor affecting conversion technology for biological hydrogen production. We performed anaerobic hydrogen fermentation of apple pomace wastes using rhizosphere bacterial microflora of rice as the parent inoculum. In the vial test, the optimal condition for hydrogen fermentation was initial pH 6.0, 35 °C, and 73.4 g pomace per liter of medium (equivalent to 10 g-hexose/L). In the batch experiment (pH 6.0, temperature 35 °C) the hydrogen yield reached 2.3 mol-H₂/mol-hexose. The time course of biogas production and PCR-DGGE analysis suggest that Clostridium spp. decomposed degradable carbohydrates rapidly and a part of the refractory carbohydrate (e.g. pectin) gradually in the apple pomace slurry. In addition to hydrogen, volatile fatty acids (VFAs) were produced in the anaerobic fermentation of apple pomace, which can be a substrate for methane fermentation. The rice rhizosphere can be a promising source of inoculum bacteria for hydrogen fermentation in combination with plant material waste like apple pomace.     

Overcoming propionic acid inhibition of hydrogen fermentation by temperature shift strategy

A novel temperature shift strategy has been proposed to overcome an inhibition on hydrogen fermentation of beverage industry wastewater (BW) due to the accumulation of propionic acid (HPr) during continuous reactor operation. The continuous performance at constant pH 5.5, temperature 37 °C and hydraulic retention time (HRT) 8 h with BW concentration of 20 g/L_{hexose-equivalent} in a stirred tank reactor (2 L) showed an accumulation of HPr to 2.36 g/L leading to a drop in hydrogen production rate (HPR) from 10 to 8.5 L L⁻¹ d⁻¹. To overcome the HPr inhibition, a temperature shift (from 37 °C) to 45 °C for 8 h was applied. This significantly improved the inhibited HPR and HY to 13.6 L L⁻¹ d⁻¹ and 1.68 mol-H₂ mol⁻¹ hexose, respectively, with a simultaneous reduction in the HPr concentration to 0.7 g/L. Microbial community analysis based on PCR-DGGE after temperature shift revealed the non-dominance of Selenomonas lacticifex and Bifidobacterium catenulatum (involved in HPr formation), and dominance of hydrogen producing bacteria namely Clostridium butyricum, Clostridium perfringenes, Clostridium acetobutylicum, and Ethanoligenens harbinense. This study demonstrated that temperature shift strategy could overcome the HPr inhibition and significantly improve the hydrogen fermentation of an industrial wastewater.     

Biohydrogen production from crude glycerol by immobilized Klebsiella sp. TR17 in a UASB reactor and bacterial quantification under non-sterile conditions

Biohydrogen production from crude glycerol by immobilized Klebsiella sp. TR17 was investigated in an up-flow anaerobic sludge blanket (UASB) reactor. The reactor was operated under non-sterile conditions at 40^○C and initial pH 8.0 at different hydraulic retention times (HRTs) (2–12 h) and glycerol concentrations (10–30 g/L). Decreasing the HRT led to an increase in hydrogen production rate (HPR) and hydrogen yield (HY). The highest HPR of 242.15 mmol H₂/L/d and HY of 44.27 mmol H₂/g glycerol consumed were achieved at 4 h HRT and glycerol concentrations of 30 and 10 g/L, respectively. The main soluble metabolite was 1,3-propanediol, which implies that Klebsiella sp. was dominant among other microorganisms. Fluorescence in situ hybridization (FISH) revealed that the microbial community was dominated by Klebsiella sp. with 56.96, 59.45, and 63.47% of total DAPI binding cells, at glycerol concentrations of 10, 20, and 30 g/L, respectively.     

Isolation,characterization and optimization of photo-hydrogen production conditions by newly isolated Rhodobacter sphaeroides KKU-PS5

A purple non-sulfur (PNS) photosynthetic bacterium was isolated from an upflow anaerobic sludge blanket (UASB) bioreactor for methane production and was identified as Rhodobacter sphaeroides KKU-PS5 (GenBank Accession no. KC481702) by 16s rRNA gene sequence analysis. Strain KKU-PS5 could utilize glucose, xylose, fructose, arabinose, malate, succinate, acetate, butyrate, lactate and D-mannitol for growth and hydrogen production. Malate was a preferred carbon source while glutamate and Aji-L (waste from the process of crystallizing monosodium glutamate) were the preferred nitrogen sources. The ability to utilize Aji-L as a low-cost nitrogen supplement for photo-biohydrogen production by the strain KKU-PS5 is considered as its desirable characteristic. The threshold substrate concentration of malate was 30 mmol/L. The optimum conditions for hydrogen production from malate were an initial pH of 7.0, FeSO₄ concentration of 4 mg/L, temperature of 30 °C and light intensity of 6 klux. Under the optimum conditions, the maximum hydrogen production, the hydrogen yield (HY) and the hydrogen production rate (HPR) of 1330 mL-H₂/L, 3.80 mol-H₂/mol-malate, and 11.08 mL-H₂/L h, respectively, were achieved. Hydrogen production under a dark/light cycle led to a decreased HY and HPR in comparison to continuous illumination.     

Enhancing the performance of dark fermentative hydrogen production using a reduced pressure fermentation strategy

The partial pressure of hydrogen is an extremely important factor for hydrogen generation. This study investigated the effect of reduced pressure (via vacuum) on hydrogen production in a CSTR reactor. The results show that the reduced pressure condition is more effective in enhancing H₂ production at lower HRT (e.g., 8–4 h) than at higher HRT (e.g., 12 h). The optimal hydrogen yield and overall hydrogen production efficiency occurred at a HRT of 6 h with a value of 4.50 mol H₂/mol sucrose and 56.2%, respectively. Meanwhile, at HRT 6 h the hydrogen production rate was 0.937 mol/L/d. In addition, the HPR could be further improved to 1.196 mol/L/d when the HRT was shortened to 4 h, obtaining a 37–271% increase in HPR when compared with that described in the relevant reports. For all experiments, butyrate and acetate were the two primary soluble metabolites, accounting for 85–99% of total soluble microbial products. Predominant production of acetate and butyrate demonstrates the efficient H₂ fermentation with reduced pressure processes.     

Direct fermentation of Laminaria japonica for biohydrogen production by anaerobic mixed cultures

A few studies have been made on fermentative hydrogen production from marine algae, despite of their advantages compared with other biomass substrates. In this study, fermentative hydrogen production from Laminaria japonica (one brown algae species) was investigated under mesophilic condition (35 ± 1 °C) without any pretreatment method. A feasibility test was first conducted through a series of batch cultivations, and 0.92 mol H₂/mol hexose_added, or 71.4 ml H₂/g TS of hydrogen yield was achieved at a substrate concentration of 20 g COD/L (based on carbohydrate), initial pH of 7.5, and cultivation pH of 5.5. Continuous operation for a period of 80 days was then carried out using anaerobic sequencing batch reactor (ASBR) with a hydraulic retention time (HRT) of 6 days. After operation for approximately 30 days, a stable hydrogen yield of 0.79 ± 0.03 mol H₂/mol hexose_added was obtained. To optimize bioenergy recovery from L. japonica, an up-flow anaerobic sludge blanket reactor (UASBr) was applied to treat hydrogen fermentation effluent (HFE) for methane production. A maximum methane yield of 309 ± 12 ml CH₄/g COD was achieved during the 90 days operation period, where the organic loading rate (OLR) was 3.5 g COD/L/d.     

Enhanced bio-hydrogen production from sugarcane juice by immobilized Clostridium butyricum on sugarcane bagasse

Immobilized Clostridium butyricum TISTR 1032 on sugarcane bagasse improved hydrogen production rate (HPR) approximately 1.2 times in comparison to free cells. The optimum conditions for hydrogen production by immobilized C. butyricum were initial pH 6.5 and initial sucrose concentration of 25 g COD/L. The maximum HPR and hydrogen yield (HY) of 3.11 L H₂/L substrate·d and 1.34 mol H₂/mol hexose consumed, respectively, were obtained. Results from repeated batch fermentation indicated that the highest HPR of 3.5 L H₂/L substrate·d and the highest HY of 1.52 mol H₂/mol hexose consumed were obtained at the medium replacement ratio of 75% and 50% respectively. The major soluble metabolites in both batch and repeated batch fermentation were butyric and acetic acids.     

Hydrogen production from alcohol wastewater with added fermentation residue by an anaerobic sequencing batch reactor (ASBR) under thermophilic operation

The objective of this study was to investigate the enhancement of hydrogen production from alcohol wastewater by adding fermentation residue using an anaerobic sequencing batch reactor (ASBR) under thermophillic operation (55 °C) and at a constant pH of 5.5. The digestibility of the added fermentation residue was also evaluated. For a first set of previous experiments, the ASBR system was operated to obtain an optimum COD loading rate of 50.6 kg/m³ d of alcohol wastewater without added fermentation residue and the produced gas contained 31% H₂ and 69% CO₂. In this experiment, the effect of added fermentation residue (100–1200 mg/l) on hydrogen production performance was investigated under a COD loading rate of 50.6 kg/m³ d of the alcohol wastewater. At a fermentation residue concentration of 1000 mg/l, the produced gas contained 40% H₂ and 60% CO₂ without methane and the system gave the highest hydrogen yield and specific hydrogen production rate of 128 ml/g COD removed and 2880 ml/l d, respectively. Under thermophilic operation with a high total COD loading rate (51.8 kg/m³ d) and a short HRT (21 h) at pH 5.5, the ASBR system could only break down cellulose (41.6%) and hemicellulose (21.8%), not decompose lignin.     

Continuous production of hydrogen from oat straw hydrolysate in a biotrickling filter

Hydrogen was produced in a biotrickling filter (BF) packed with perlite and fed with oat straw acid hydrolysate at 30 °C. Inlet chemical oxygen demand (COD) from 1.2 to 35 g/L and hydraulic retention time (HRT) between 24 h and 6 h were assayed. With increasing inlet COD or decreasing HRT, H₂ production rate (HPR) increased but H₂ production yield (HY) decreased. Maximum HPR of 81.4 mL H₂/L_reactor h (3.3 mmol H₂/L_reactor h) and HY of 2.9 mol H₂/mol_{hexose consumed} were found at an inlet COD of 0.05 g_COD/L h (HRT 24 h) and 2.9 g_COD/L h (HRT 12 h), respectively. Maximum hydrogen composition in gas was 45 ± 4% (v/v) with CO₂ as balance. Methane was not detected. Maximum HPR and inlet COD used in this work were higher than others reported for reactors with suspended or fixed biomass. However, implementation of strategies for biomass control to avoid reactor clogging is needed.     

Effect of hydraulic retention time on a continuous biohydrogen production in a packed bed biofilm reactor with recirculation flow of the liquid phase

The present paper reports on results obtained from experiments carried out in a laboratory-scale anaerobic packed bed biofilm reactor (APBR), with recirculation of the liquid phase, for continuously biohydrogen production via dark fermentation. The reactor was filled with Kaldnes^® biofilm carrier and inoculated with an anaerobic mesophilic sludge from a urban wastewater treatment plant (WWTP). The APBR was operated at a temperature of 37 °C, without pH buffering. The effect of theoretical hydraulic retention time (HRT) from 1 to 5 h on hydrogen yield (HY), hydrogen production rate (HPR), substrate conversion and metabolic pathways was investigated. This study indicates the possibility of enhancing hydrogen production by using APBR with recirculation flow. Among respondents values of HRT the highest average values of HY (2.35 mol H₂/mol substrate) and HPR (0.085 L h^?1L^?1) have been obtained at HRT equal to 2 h.     

Enhancement of hydrogen production by recycling of methanogenic effluent in two-phase fermentation of food waste

The feasibility of operational strategies was investigated for hydrogen and methane production from food waste. Food waste was heat-treated at 70 °C and fed to a two-phase anaerobic sequencing batch fermenting system. Maximum hydrogen productivity of 1.19 m³ H₂/m³ d was observed at a food waste concentration of 30 g carbohydrate/L, a hydraulic retention time of 2 d, and a solids retention time of 3.4 d. The effluent from hydrogenesis was efficiently converted to methane at an organic loading rate of up to 3.6 kg COD/m³.d. The methanogenic effluent was then recycled to the hydrogenesis reactor without any pretreatment. The recycled effluent not only successfully replaced external dilution water and decreased alkaline dosage by 75%, but also increased hydrogen production by 48%, resulting in hydrogen productivity of 1.76 m³/m³ d. The two-phase digestion with recycling would convert 91% of organic pollutants in food waste to hydrogen (8%) and methane (83%) without any external dilution water.     

Simultaneous saccharification and fermentation of cellulose for bio-hydrogen production by anaerobic mixed cultures in elephant dung

The objective of this study was to optimize the culture conditions for simultaneous saccharification and fermentation (SSF) of cellulose for bio-hydrogen production by anaerobic mixed cultures in elephant dung under thermophilic temperature. Carboxymethyl cellulose (CMC) was used as the model substrate. The investigated parameters included initial pH, temperature and substrate concentration. The experimental results showed that maximum hydrogen yield (HY) and hydrogen production rate (HPR) of 7.22 ± 0.62 mmol H₂/g CMC_added and 73.4 ± 3.8 mL H₂/L h, respectively, were achieved at an initial pH of 7.0, temperature of 55 °C and CMC concentration of 0.25 g/L. The optimum conditions were then used to produce hydrogen from the cellulose fraction of sugarcane bagasse (SCB) at a concentration of 0.40 g/L (equivalent to 0.25 g/L cellulose) in which an HY of 7.10 ± 3.22 mmol H₂/g cellulose_added. The pre-dominant hydrogen producers analyzed by polymerase chain reaction-denaturing gel gradient electrophoresis (PCR-DGGE) were Thermoanaerobacterium thermosaccharolyticum and Clostridium sp. The lower HY obtained when the cellulose fraction of SCB was used as the substrate might be due to the presence of lignin in the SCB as well as the presence of Lactobacillus parabuchneri and Lactobacillus rhamnosus in the hydrogen fermentation broth.     

Fermentative hydrogen production from starch using natural mixed cultures

Batch and continuous tests were conducted to evaluate fermentative hydrogen production from starch (at a concentration of chemical oxygen demand (COD) 20 g/L) at 35 °C by a natural mixed culture of paper mill wastewater treatment sludge. The optimal initial cultivation pH (tested range 5–7) and substrate concentration (tested range 5–60-gCOD/L) were evaluated by batch reactors while the effects of hydraulic retention time (HRT) on hydrogen production, as expressed by hydrogen yield (HY) and hydrogen production rate (HPR), were evaluated by continuous tests. The experimental results indicate that the initial cultivation pH markedly affected HY, maximum HPR, liquid fermentation product concentration and distribution, butyrate/acetate concentration ratio and metabolic pathway. The optimal initial cultivation pH was 5.5 with peak values of HY 1.1 mol-H₂/mol-hexose maximum HPR 10.4 mmol-H₂/L/h and butyrate concentration 7700 mg-COD/L. In continuous hydrogen fermentation, the optimal HRT was 4 h with peak HY of 1.5 mol-H₂/mol-hexose, peak HPR of 450 mmol-H₂/L/d and lowest butyrate concentration of 3000 mg-COD/L. The HPR obtained was 280% higher than reported values. A shift in dominant hydrogen-producing microbial population along with HRT variation was observed with Clostridium butyricum, C. pasteurianum, Klebshilla pneumoniae, Streptococcus sp., and Pseudomonas sp. being present at efficient hydrogen production at the HRTs of 4–6 h. Strategies based on the experimental results for optimal hydrogen production from starch are proposed.     

The kinetic characterization of photofermentative bacterium Rhodopseudomonas faecalis RLD-53 and its application for enhancing continuous hydrogen production

In this work, the kinetic characterization of hydrogen production by the photofermentative bacteria Rhodopseudomonas faecalis RLD-53 was investigated at different growth phase. During entire fermentation, 89.30% of total biomass was accumulated in exponential growth phase, while hydrogen yield was only 1.82 mol H₂/mol acetate at the expense of 51.25% substrate. In the stationary phase, biomass synthesis was minimal (7.51%), and 38.17% of the substrate was directly converted into hydrogen. As a result, hydrogen (59.19%) was mainly produced in stationary phase with highest hydrogen yield of 3.67 mol H₂/mol acetate. Consequently, bacteria in stationary phase were most effective for hydrogen production. Based on these findings, a novel membrane photobioreactor was developed to retain bacteria during stationary phase in reactor through membrane separation. Maximum rate (32.82 ml/l/h) and yield (3.27 mol H₂/mol acetate) of hydrogen production were achieved using membrane photobioreactor under the continuous operation. Therefore, using bacteria in stationary phase as hydrogen producer can offer considerable benefits for enhancing photo-hydrogen production.     

Biohydrogen production from waste glycerol and sludge by anaerobic mixed cultures

Key factors affecting biohydrogen production from waste glycerol and sludge by anaerobic mixed cultures were optimized using response surface methodology (RSM) with central composite design (CCD). Investigated parameters were waste glycerol concentration, sludge concentration, and the amount of Endo–nutrient addition. Concentrations of waste glycerol and sludge had a significant individual effect on hydrogen production rate (HPR) (p ≤ 0.05). The interactive effect on HPR (p ≤ 0.05) was found between waste glycerol concentration and sludge concentration. The optimal conditions for the maximum HPR were: waste glycerol concentration 22.19 g/L, sludge concentration 7.16 g-total solid (TS/L), and the amount of Endo–nutrient addition 2.89 mL/L in which the maximum HPR of 1.37 mmol H₂/L h was achieved. Using the optimal conditions, HPR from a co-digestion of waste glycerol and sludge (1.37 mmol H₂/L h) was two times greater than the control (waste glycerol without addition of sludge) (0.76 mmol H₂/L h), indicating a significant enhancement of HPR by sludge. Major metabolites of the fermentation process were ethanol, 1,3-propanediol (1,3-PD), lactate, and formate.