Buckling of fuel rods under inertia loading

Abstract

The buckling analysis of fuel rods during an end drop impact of a spent fuel transportation cask has traditionally been performed to demonstrate the structural integrity of the fuel rod cladding or the integrity of the fuel geometry in criticality evaluations for a cask drop event. The actual calculation of the fuel rod buckling load, however, has been the subject of some controversy, with estimates of the critical buckling load differing by as much as a factor of 5. Typically, in the buckling analysis of a fuel rod, assumptions are made regarding the percentage of fuel mass that is bonded to or that participates with the cladding during the buckling process, with estimates ranging from 0 to 100%. The greater the percentage of fuel mass that is assumed to be bonded to the cladding, the higher the inertia loads on the cladding, and, therefore, the lower the 'g' value at which buckling occurs. However, these solutions do not consider displacement compatibility between the fuel and the cladding during the buckling process. By invoking displacement compatibility between the fuel column and the cladding column, this paper presents an exact solution for the buckling of fuel rods under inertia loading. The results show that the critical inertia load magnitude for the buckling of a fuel rod depends on the weight of the cladding and the total weight of the fuel, regardless of the percentage of fuel mass that is assumed to be attached to or participate with the cladding in the buckling process. Therefore, 100% of the fuel always participates in the buckling of a fuel rod under inertia loading.     

Verification of activity release compliance with regulatory limits within spent fuel transport cask assessment

Abstract

Admissible limits for activity release from type B(U) packages for spent fuel transport specified in the International Atomic Energy Agency regulations (10^?6 A₂ h^?1 for normal conditions of transport and A₂ per week for accidental conditions of transport) have to be kept by an appropriate function of the cask body and its sealing system. Direct measurements of activity release from the transport casks are not feasible. Therefore, the most common method for the specification of leak tightness is to relate the admissible limits of activity release to equivalent standardised leakage rates. Applicable procedure and calculation methods are summarised in the International Standard ISO 12807 and the US standard ANSI N14·5. BAM as the German competent authority for mechanical, thermal and containment assessment of packages liable for approval verifies the activity release compliance with the regulatory limits. Two fundamental aspects in the assessment are the specification of conservative design leakage rates for normal and accidental conditions of transport and the determination of release fractions of radioactive gases, volatiles and particles from spent fuel rods. Design leakage rates identify the efficiency limits of the sealing system under normal and accidental transport conditions and are deduced from tests with real casks, cask models or components. The releasable radioactive content is primarily determined by the fraction of rods developing cladding breaches and the release fractions of radionuclides due to cladding breaches. The influence of higher burn-ups on the failure probability of the rods and on the release fractions are important questions. This paper gives an overview about methodology of activity release calculation and correlated boundary conditions for assessment.     

A methodology for the evaluation of fuel rod failures under accident conditions

Abstract

Recent studies on the long-term behaviour of high-burnup spent fuel have shown that, under normal conditions of storage, challenges to cladding integrity from various postulated damage mechanisms, such as delayed hydride cracking, stress-corrosion cracking and long-term creep, would not lead to any significant safety concerns during dry storage, and regulatory rules have subsequently been established to ensure that a compatible level of safety is maintained. However, similar regulatory rules have not yet been developed to address failures of fuel rod cladding that could potentially lead to reconfigured fuel geometry under hypothetical transport accidents. At issue is the effect on cladding ductility of potential changes in zirconium hydride morphology during dry storage. Recent studies have shown that above a certain level of cladding hoop stress, the decaying temperature history during dry storage can cause the hydrogen in solid solution to precipitate in the form of radial hydrides, which, depending on their relative concentration, can induce brittle failures in the cladding. From a US regulatory perspective such cladding failures, if they were to cause fuel reconfiguration, could invalidate the cask's criticality and shielding licensing analyses, which are based on coherent geometry. This paper describes a methodology for high-burnup spent fuel to determine the frequency of cladding failure and failure modes under drop accidents, considering end-of-storage spent fuel conditions. The degree to which spent fuel reconfiguration could occur during handling or transport accidents would depend to a large extent on the number of fuel rod failures and the type and geometry of the failure modes. Such information can only be developed analytically, as there are no direct experimental data that can provide guidance on the level of damage that can be expected. To this end, this paper focuses on the development of a methodology for modelling and analysis that deals with this general problem on a generic basis. First, consideration is given to defining accident loading that is equivalent to the bounding hypothetical transport accident of a 9 m drop onto an essentially unyielding surface. Second, an analytically robust material constitutive model, an essential element in a successful structural analysis, is required. A model of material behaviour, with embedded failure criteria, for cladding containing various concentrations of circumferentially and radially oriented hydrides has been developed and implemented in a finite-element code. The hydride precipitation model, which describes the hydride structure of the cladding at the end of dry storage, and the hydride-dependent properties of high-burnup fuel cladding form the main input to the constitutive model. The third element in the overall process is to utilise this material model and its host finite-element code in the structural analysis of a transport cask subjected to bounding accident loading to calculate fuel rod failures and failure mode configurations. This requires detailed modelling of the transport cask and its internal structure, which includes the canister, basket, fuel assembly grids and fuel rods. The overall methodology is described.     

Expansion of the capabilities of the GA-4 legal weight truck spent fuel shipping cask

Abstract

General Atomics has developed the model GA-4 legal weight truck spent fuel cask, a high-capacity cask for the transport of four pressurised water reactor (PWR) spent fuel assemblies, and obtained a certificate of compliance (CoC, No. 9226) in 1998 from the US Nuclear Regulatory Commission (NRC). The currently authorised contents for this CoC, however, are much more limiting than the actual capability of the GA-4 cask to transport spent PWR fuel assemblies. The purpose of this paper is to show how the authorised contents can be significantly expanded by additional analyses without any changes to the physical design of the package. Using burn-up credit as outlined in US NRC Interim Staff Guidance 8, Revision 2, the authorised contents can be significantly expanded by increasing the maximum enrichment as the burn-up increases. Use of burn-up credit eliminates most of the criticality imposed limits on authorised package contents, but shielding still limits the use of the cask for higher burn-up, short-cooled fuel. By reducing the number of assemblies transported (downloading) to two and using shielding inserts, even high-burn-up fuel with reasonable cooling times can be transported.     

Radiological aspects and behavior of spent fuel considering long-term storage

For spent nuclear fuel management in Germany, the concept of dry interim storage in dual purpose casks before direct disposal is applied. Current operation licenses for storage facilities have been granted for a storage time of 40 years. Due to the current delay in site selection, an extension of the storage time seems inevitable. In consideration of this issue, GRS performed burnup calculations, thermal and mechanical analyses as well as particle transport and shielding calculations for UO₂ and MOX fuels stored in a cask to investigate long-term behavior of the spent fuel related parameters and the radiological consequences. It is shown that at the beginning of the dry storage period, cladding hoop stress levels sufficient to cause hydride reorientation could be present in fuel rods with a burnup higher than 55 GWd/tHM. The long-term behavior of the cladding temperatures indicates the possibility of reaching the ductile-to-brittle transition temperature during extended storage scenarios. Surface dose rates are 3 times higher when a cask is partially loaded with 4 MOX fuel assemblies. Due to radioactive decay, long-term storage will have a positive impact on the radiological environment around the cask.     

Multiple water barriers: alternative to assessment of fuel assemblies during accident conditions of transport

Abstract

Packages for the transport of radioactive material have to comply with national and/or international regulations. These regulations are widely based on the requirements set forth by the International Atomic Energy Agency (IAEA) in the 'Regulations for the safe transport of radioactive material'. In this framework, packages to transport fuel assemblies (including spent fuel assemblies) have to meet the requirements for packages containing fissile material. In accident conditions of transport, the applicant for the package design approval has to show that the package remains subcritical taking due account of the status of the contents in these conditions. In most cases, considering water ingress in the package, it is not possible to assume that the fissile material included in the fuel assemblies is dispersed in the package with the most severe conceivable distribution regarding criticality. In order to alleviate this difficulty, during the last years, we have provided a significant better knowledge of the conditions of the fuel assemblies to be transported. This was part of the Fuel Integrity Project, whose progress was regularly reported during PATRAM 2001 and PATRAM 2004 Symposia. However, for packages which encounter a large g-load during accident conditions of transport and/or which contain spent fuel assemblies with very high burn-up, it can be difficult to demonstrate that the fuel assemblies are not significantly damaged. Then, to make the criticality assessment considering water inleakage into the flask and a large release of fissile material within its cavity will not allow meeting the subcriticality criteria. For that reason, for our package designs, which use a gas and not water as an internal coolant and which fall into that category, the author has decided to take credit of the possibilities provided by the subparagraph 677 (b) of the Regulations. This paragraph allows not taking into account water in the package, provided that the package exhibits 'multiple high standard water barriers'. The paper describes the author's experience with the implementation of this paragraph. Two different cases are considered: either a double vessel, or a double lid. It will be explained when each of these solutions is implemented, and give examples of package designs with such features, as well as the approvals which were granted for these designs in various countries.     

CEFR-MOX新燃料组件运输货包临界安全计算

易裂变材料运输过程中重要的安全问题之一是临界安全。在对运输货包进行临界安全分析中必须要同时考虑多货包阵列形式、事故后货包损伤对临界安全影响、最佳水慢化条件等因素。本文采用MCNP 程序针对CEFR-MOX新燃料组件运输货包进行了临界安全计算。计算结果表明:MCNP程序(采用核截面库为ENDF/B-V库)对本问题的次临界限值为0.924 6;正常运输条件下无限个运输货包的最大k_eff值为0.574 4,运输事故条件下无限个运输货包的最大k_eff值为0.659 7。根据临界安全指数的定义,确定CEFR-MOX新燃料组件运输货包的临界安全指数为0。     

Thermal analysis of a storage cask for 24 spent PWR fuel assemblies

Abstract

The purpose of this paper is to perform a thermal analysis of a spent fuel storage cask in order to predict the maximum concrete and fuel cladding temperatures. Thermal analyses have been carried out for a storage cask under normal, off-normal and accident conditions. The environmental temperature is assumed to be 27°C under the normal condition. The off-normal condition has an environmental temperature of 40°C. An additional off-normal condition is considered as a partial blockage of the air inlet ducts. Four of the eight inlet ducts are assumed to be completely blocked. The accident condition is defined as a 100% blockage of air inlet ducts. The storage cask is designed to store 24 PWR spent fuel assemblies with a burn-up of 55,000 MWD/MTU and a cooling time of 7 years. The decay heat load from the 24 PWR assemblies is 25.2 kW. Thermal analyses of the ventilation system have been carried out for the determination of the optimum duct size and shape. The finite-volume computational fluid dynamics code FLUENT was used for the thermal analysis. From the results of the analysis, the maximum temperatures of the fuel rod and concrete overpack were lower than the allowable values under the normal, off-normal and accident conditions.     

German approach and feedback on experience of transportability of SNF packages after interim storage

In Germany, the concept of dry interim storage of spent fuel in dual purpose metal casks is implemented, currently for periods of up to 40 years. The casks being used have an approved package design in accordance with the international transport regulations. The license for dry storage is granted on the German Atomic Energy Act with respect to the recently revised ‘Guidelines for dry interim storage of irradiated fuel assemblies and heat-generating radioactive waste in casks’ by the German Waste management Commission. For transport on public routes between or after long term interim storage periods, it has to be ensured that the transport and storage casks fulfil the specifications of the transport approval or other sufficient properties, which satisfy the proofs for the compliance of the safety objectives at that time. In recent years, the validation period of transport approval certificates for manufactured, loaded and stored packages were discussed among authorities and applicants. A case dependent system of 3, 5 and 10 years was established. There are consequences for the safety cases in the Package Design Safety Report, including evaluation of long term behaviour of components and specific operating procedures of the package. The present research and knowledge concerning the long term behaviour of transport and storage cask components have to be consulted as well as experiences from interim cask storage operations. Challenges in the safety assessment are e.g. the behaviour of aged metal and elastomeric gaskets under IAEA test conditions to ensure that the results of drop tests can be transferred to the compliance of the safety objectives at the time of transport after the interim storage period. Assessment methods for the material compatibility, the behaviour of fuel assemblies and the aging behaviour of shielding parts are issues as well. This paper describes the state of the art technology in Germany, explains recent experience on transport preparation after interim storage and points out arising prospective challenges.     

Effect of irradiation on the impact and seismic response of a spent fuel storage and transport cask

The spent fuel storage and transport cask must withstand various accident conditions such as fire, free drop and puncture in accordance with the requirement of the IAEA and domestic regulations. The spent fuel storage and transport cask should maintain the structural safety not to release radioactive material in any condition. And also the effects of the irradiation should be considered because the spent fuels stored in the cask for a long time and be possible to change the mechanical properties of the cask.In this study, the changed mechanical properties of the cask after irradiation for the 30 years storage periods are assumed and applied to the impact analysis using ABAQUS/Explicit code and seismic analysis using ANSYS code. The stress intensity on each part of the cask is calculated and the effects of irradiation are studied and structural integrity of the package is evaluated.     

Implementation of burn-up credit approach for transport and storage cask

Abstract

TN International currently uses burn-up credit methodology for the design of casks dedicated to the transport of pressurised water reactor uranium oxide spent fuel assemblies. As long as the fuel enrichment of the pressurised water reactor fuel assemblies was sufficiently low, a burn-up credit methodology based on the sole consideration of actinides and the use of a partial burn-up was satisfactory to cover the needs without necessity to design new casks. Nevertheless, the continuous increase in the fuel enrichment during the last decade has led TN International to continue the investigations on the burn-up credit methodology to limit both the increase in the neutron poison content in the new basket designs and the burn-up constraints attached to the acceptability of the fuel assemblies for transport. The strategy of TN International was then to take benefit of the large negative reactivity reserves, which might be gained by the consideration of the fission products coming from the fuel irradiation. A big step forward has recently been reached by TN International on this field with the definition of an advanced burn-up credit methodology based on the consideration of relevant fission products recommended by OECD. In the meantime, TN International has taken the opportunity to use such burn-up credit approach in the design of the TN 24 E transport and storage cask developed for the German nuclear power plants. The relevant task has been carried out according to the German standard DIN 25712 for burn-up credit application. The present paper will describe the basic principles of the burn-up credit methodology implemented by TN International such as:

(i) the current state of the art concerning the burn-up credit application in the criticality assessment

(ii) the basic approach used for the implementation of the advanced burn-up credit methodology (bounding axial burn-up profiles, fuel irradiation parameters, fission products, etc.)

(iii) the area of validity of the TN International burn-up credit approach with fission products

(iv) example of application of the burn-up credit methodology for the design of the TN 24 E transport and storage cask under licensing in Germany

(v) the perspectives of development of the burn-up credit methodology.     

Analyses to demonstrate structural performance of KN18 in hypothetical drop accident scenarios

Abstract

The KN18 is a new cask design by KONES for KHNP for the dry or wet transportation of up to 18 PWR spent nuclear fuel assemblies in South Korea. The containment vessel consists of a cylindrical thick-walled forged steel body, closed by a stainless steel lid with bolts. Spent fuel assemblies are located in a basket which consists of a tube disc system. Two pairs of trunnions are attached for lifting, manoeuvring and tie-down. A pair of impact limiters manufactured from wood and encased in steel cladding provide impact energy absorption during the hypothetical accident conditions. The package complies with the requirements of 10 CFR Part 71 for Type B(U)F packages. It received its transport license from the Korean Competent Authority KINS in early 2010 and is expect to enter service in 2011. Structural performance of the package in the normal and accident conditions were demonstrated against the requirements of 10 CFR Part 71 by analysis including extensive calculations by state-of-the-art finite element methods, and confirmed by tests carried out on a one-third scale test model which were also used to verify the numerical tool and methods used in the analyses. For the analyses of the hypothetical accident drop conditions, the models consisted of the complete package, including the impact limiters, the containment structure and the basket, which was modelled explicitly in detail and in three dimensions, to take into account the complex interaction between the components and the non-linearities in the geometry, the material behaviour and overall behaviour. The analyses were carried out using the explicit transient finite element method so that the transient behaviour could be robustly simulated. This paper presents two of the analyses from the suite of analyses for demonstrating the performance of the package in the hypothetical accident drop scenarios, discussing the analyses methodology, modelling technique and evaluation methodology, as well as analyses results and package response. The one-third scale model drop testing and benchmarking of the model to the scale model tests are the subject of a separate paper.     

New approach to evaluate lattice expansion of light water reactor fuel elements on criticality safety of transport packages under impact accidents

Abstract

In order to safely transport packages containing light water reactor fuel assemblies, it is essential to maintain the fuel assemblies in a subcritical state in accidents during transport. To evaluate nuclear criticality safety, an estimator is required to determine an absolutely safe level based not only on hypothetical accidents but also on practical accident levels which, to some extent, are based on actual accidents. The purpose of the present study is to suggest the arrangement of the deformation range of the fuel assembly after an actual accident, and to obtain the maximum value of the neutron effective multiplication factor based on the criticality safety assessment for the transport cask. In the present study, two kinds of criticality calculations for the package were considered: large scale pin pitch shift and small scale pin pitch shift. For the large scale pin pitch shift, a parameter which determines the location of each fuel pin which constitutes the fuel assembly was introduced so that the criticality calculation for the fuel assembly with non-uniform lattice pitch can be performed parametrically. The result of the criticality calculation using the parameter made it clear that the fuel pin pitch is sensitive to the neutron reactivity because each of the fuel pin pitches is related to a ratio of the fissile to the moderator, and that the relationship of the ratio to the neutron reactivity depends on the type of the fuel assembly involved, i.e. the type of a nuclear reactor in which a fuel assembly is used. For the small scale pin pitch shift, the study focused on the small displacement of each fuel pin. The small displacement of each fuel pin pitch can be described probabilistically using the stochastic geometry routine in MCNP code. Using the scheme in combination with the scheme for the large scale pin pitch shift, the maximum value of the neutron effective multiplication factor of the package after an accident can be obtained. This scheme is useful to determine the maximum neutron effective multiplication factor for the criticality safety evaluation.     

Spent fuel transport using cask loaded outside pool

Abstract

During the last year, Sogin (the Italian company in charge for decommissioning of Italian nuclear power plants) had to implement an accelerated decommissioning plan of a EUREX spent fuel pool due to finding a water leakage into the environment from the pool. EUREX is no longer operating a pilot reprocessing plant, which some years ago became the responsibility of Sogin. There were 52 spent fuel assemblies from the Trino Vercellese PWR nuclear power plant, 48 irradiated pins from a Garigliano BWR fuel assembly, and 10 plates from an irradiated MTR fuel assembly stored in the EUREX pool, so the first step of the accelerated decommissioning plan consisted in the evacuation of this spent fuel. Considering the necessity to start the evacuation as soon as possible, Sogin decided to use an already existing cask (AGN-1) used in the past for the transport of Trino and Garigliano fuel assemblies. This cask was requalified in order to obtain a transport licence for the fuel assemblies stored in the EUREX pool according to ADR 2005 regulation. The transport license for the AGN-1 cask loaded with EUREX fuel assemblies was released by APAT (the Italian Safety Authority) in the spring of 2007. Owing to the limited capacity of the EUREX pool crane (27 t for nuclear loads) and limited dimensions of pool operational area, it was not possible to transfer the AGN-1 cask (50 t) into the pool for fuel assemblies charging. The solution implemented to overcome this problem was the loading of the cask outside the pool. A special shielding shuttle was developed and used to allow safe spent fuel transfer between the pool and the cask. This procedure avoided also the problem of excessive contamination of cask surfaces that could have occurred due to very high level of contamination of EUREX pool water if the cask had been immersed in the pool. Additional shielding devices were developed and used to reduce dose rate during cask loading operations. Although the evacuation of spent fuel assemblies from the EUREX pool was a very challenging activity due to the short time available, unfavourable space conditions inside the pool building and handling tool limitations; all loading and transport operations were performed successfully and without particular problems. Ten transports were carried out to evacuate all of the spent fuel stored in the EUREX pool. Spent fuel was transferred to the Avogadro Deposit pool. The first loading sequence started on 2 May 2007 and the first transport was performed on 6 May 2007. The tenth and last transport was performed on 21 July 2007. A dose less than 50 μSv (neutron + gamma) was measured for the most exposed operator during a complete cask loading sequence.     

CUPIDON-code decrivant le comportement thermique et mecanique d'un crayon combustible de reacteur a eau sous pression au cours d'un accident de depressurisation

In the scope of the PHEBUS experimental program to be performed in Cadarache on the behaviour of PWR's fuel assemblies under loss of coolant accidental conditions, a computer code has been developed to help designing the experimental rods and to contribute to the definition of the test runs.This code, dubbed CUPIDON, deals only with the thermal and mechanical behaviour of the rods as well as the oxidation of the cladding outside surface; it does not include any thermohydraulic subroutine. Rather, it is coupled with the RELAP code for providing necessary input data such as coolant temperatures and pressures and cladding-to-coolant heat transfer coefficients. It is restricted to a single, non irradiated, rod of short length as representing the PHEBUS experimental conditions.It is a two dimensional code, using a finite difference resolving technique. It calculates the radial thermal profile across each section of the rod, the stress and creep rate to which the cladding is submitted and the rate of formation of the oxide layer on the surface of the cladding under steady state and transient conditions. As cladding plastic strain input data, it is using the EDGAR-ZY experimental results.     

BWR spent fuel transport and storage with TN9/4 and TN24BH casks

Abstract

In 2001 the Swiss nuclear utilities started to store spent fuel in dry metallic dual purpose casks at ZWILAG, the Swiss interim storage facility. BKW FMB Energy Ltd, as the owner of the Mühleberg nuclear power plant, is involved in this process and has selected to store the spent fuel in a new high capacity dual purpose cask, the TN24BH. For the transport Cogema Logistics has developed a new medium size cask, the TN9/4, to replace the NTL9 cask, which has performed numerous shipments of BWR spent fuel in past decades. Licensed by the IAEA 1996, the TN9/4 is a 40 t transport cask, for seven BWR high burnup spent fuel assemblies. The spent fuel assemblies can be transferred to the ZWILAG hot cell in the TN24BH cask. These casks were first used in 2003. Ten TN9/4 shipments were made, and one TN24BH was loaded. After a brief presentation of the operational aspects, the paper will focus on the TN24BH high capacity dual purpose cask and the TN9/4 transport cask and describe in detail their characteristics and possibilities.     

Reversal bending fatigue test system for investigating vibration integrity of spent nuclear fuel during transportation

Transportation packages for spent nuclear fuel (SNF) must meet safety requirements under normal and accident conditions as specified by federal regulations. During transportation, SNF experiences unique conditions and challenges to cladding integrity due to the vibrational and impact loading during road or rail shipment. Oak Ridge National Laboratory (ORNL) has been developing testing capabilities that can be used to improve the understanding of the impacts on SNF integrity due to vibration loading, especially for high burn-up SNF in normal transportation operation conditions. This information can be used to meet the nuclear industry and U.S. Nuclear Regulatory Commission needs in the area of safety and security of SNF storage and transportation operations. The ORNL developed test system can perform reversal bending fatigue testing to evaluate both the static and dynamic mechanical response of SNF rods under simulated loads. The testing apparatus is also designed to meet the challenges of hot cell operation, including remote installation and detachment of the SNF test specimen, in situ test specimen deformation measurement, and implementation of a driving system suitable for use in a hot cell. The system contains a U frame set-up equipped with uniquely designed grip rigs to protect the SNF rod sample and to ensure valid test results, and uses three specially designed linear variable differential transformers to obtain the in situ curvature measurement. A variety of surrogate test rods have been used to develop and calibrate the test system as well as in performing a series of systematic cyclic fatigue tests. The surrogate rods include stainless steel (SS) cladding, SS cladding with cast epoxy and SS cladding with alumina pellet inserts simulating fuel pellets. Testing to date has shown that the interface bonding between the SS cladding and the alumina pellets has a significant impact on the bending response of the test rods as well as their fatigue strength. The failure behaviours observed from tested surrogate rods provide a fundamental understanding of the underlying failure mechanisms of the SNF surrogate rod under vibration, which has not been achieved previously. The newly developed device is scheduled to be installed in the hot cell in summer 2013 to test high burn-up SNF.     

中国先进研究堆新燃料组件运输的临界安全分析

在新燃料组件运输过程中,临界安全是重点。使用MCNP程序对中国先进研究堆新燃料组件的运输进行临界安全计算分析,通过选取最不利临界安全的次临界限值、组件模型参数、事故工况来保证计算结果的保守性。结果表明,运输货包的临界安全指数可确定为0。该结果可为中国先进研究堆（CARR）的新燃料组件运输容器的研发提供参考依据。     

Thermal analysis of proposed transport cask for three advanced burner reactor used fuel assemblies

Abstract

Preliminary studies of used fuel generated in the US Department of Energy's Advanced Fuel Cycle Initiative have indicated that current used fuel transport casks may be insufficient for the transportation of said fuel. This work considers transport of three 5-year-cooled oxide advanced burner reactor used fuel assemblies with a burn-up of 160 MWD kg^–1. A transport cask designed to carry these assemblies is proposed. This design employs a 7-cm-thick lead gamma shield and a 20-cm-thick NS-4-FR composite neutron shield. The temperature profile within the cask, from its centre to its exterior surface, is determined by two-dimensional computational fluid dynamics simulations of conduction, convection and radiation within the cask. Simulations are performed for a cask with a smooth external surface and various neutron shield thicknesses. Separate simulations are performed for a cask with a corrugated external surface and a neutron shield thickness that satisfies shielding constraints. Resulting temperature profiles indicate that a three-assembly cask with a smooth external surface will meet fuel cladding temperature requirements but will cause outer surface temperatures to exceed the regulatory limit. A cask with a corrugated external surface will not exceed the limits for both the fuel cladding and outer surface temperatures.     

Description of the German Concept of Final Storage Cask

Abstract

The German storage concept for the direct final storage of spent fuel assemblies from LWR reactors is described. The final storage concept is designed in such a way that it encompasses the whole spectrum of fuel elements to be stored from German reactors, Le. U fuel assemblies and MOX fuel assemblies with a mean bumup of 55 GW.d.t^?1 heavy metal were considered. The further design requirements are defined in such a way that the cask concept satisfies the conditions for type B(U) transport, interim storage and fmal storage. The safe long-term containment of the activity is guaranteed by an inner cask welded leak-tight; the sufficient shielding and the transport packaging are ensured by a shielding cask.