Compact tri‐notched ultrawideband bandpass filter design using CSRR,DGS, and FMRR configurations

The folded multiple‐mode resonators with complementary split ring resonator (CSRR), and defected ground structures (DGS) are introduced for notched ultrawideband (UWB) bandpass filter (BPF) design in this article. Using the CSRR, FMRR, notched wide‐band BPF, a notch response can exist in the UWB passband for blocking the interference. Adjusting the size factor of CSRR, the wide tuning ranges of notch frequencies included the desired frequencies of 5.2/5.8 GHz are achieved. The lower insertion loss (0.31 dB), higher rejection level (?48.40 dB), wider bandwidth (FBW 75%), and wider stopband (extended to 2.01 f₀ below ?20 dB rejection level) of UWB band at the central frequency f₀ = 4.58 GHz are obtained. Second, design a CSRR, DGS, FMRR, tri‐notched UWB filter, the wider bandwidth (3.1–9.8 GHz) with FBW = 126%, lower insertion loss (0.26 dB), and higher rejection level (?44 dB) of UWB band at central frequency f₀ = 5.6 GHz are presented. Using the CSRR and interdigital couple, three notch responses can exist in the UWB passband for blocking the interference signals. Adjusting the size factor of CSRR and interdigital couple, the wide tuning ranges of notch frequencies included the desired frequencies of 5.18/6.10/8.08 GHz are achieved. The wide tuning ranges of three notched frequencies cover from 5.0 to 8.4 GHz. It is a simple way to control the notch responses. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:571–579, 2014.     

Compact ultra‐wideband bandpass filter with variable notch characteristics based on transversal signal‐interaction concepts

A novel technique is presented to design highly compact microstrip ultra‐wideband (UWB) bandpass filters that exhibit high selectivity quasi‐elliptical response. The design is based on transversal signal‐interaction concepts that enable the inclusion of single or dual notch‐bands within the filter's passband to eliminate interference from other services that coexist within the UWB spectrum. The filter configuration comprises of two transmission paths which include folded T‐shaped stepped impedance resonators (SIRs) that are capacitively coupled with the input/output lines to enable signal transmission. It is shown that by combining the filters of different passband centre frequencies an UWB filter can be realised with either a single‐ or dual‐notch function. The theoretical performance of the filter is corroborated via measurements to confirm that the proposed filter exhibits UWB passband of 123% for a 3 dB fractional bandwidth, a flat group‐delay with maximum variation of less than 0.3 ns, passband insertion loss less than 0.94 dB, high selectivity, a sharp rejection notch‐band with attenuation of ?23 dB, and a good overall out‐of‐band performance. Furthermore, the filter occupies a significantly small area of 94 mm² compared with its classical counterparts. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:549–559, 2014.     

Band‐pass filter design using modified CSRR‐DGS

In this article, a novel compact band‐pass filter (BPF) with sharp cutoffs and a wide stop‐band is presented. The BPF is basically designed by cutting a modified complementary split‐ring resonator (CSRR) from the ground of two separated microstrip feed lines and has a 71% fractional bandwidth from 4.1 to 9 GHz. Because of the high insertion loss, the designed filter should be packed in a metallic cavity that has undesirable resonances in the stop‐band of the BPF. For eliminating cavity resonances, an evolutionary optimization technique based on changing the pixels of the CSRR defected ground structure is used. A prototype of the final structure obtained from the optimization technique is fabricated. The measurement results show that the optimized filter have a pass band from 4 to 8 GHz with a rejection better than 15 dB from 4 to 15 GHz. The designed filters have compact dimensions of 12 × 12 × 0.787 mm³. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:544–548, 2014.     

Compact UWB bandpass filter with dual‐notch bands using asymmetric tri‐section stepped impedance resonator

In this study, a novel high selective UWB band pass filter (BPF) with dual notch band is presented. UWB BPF is realized using stub‐loaded multiple‐mode resonator (MMR). The MMR is constructed by loading a quintuple mode open stub at the centre in an asymmetric tri‐section stepped impedance resonator (ATSSIR). Five modes, including two odd modes and three even modes, placed within UWB band. Two transmission zeros generated by the fractal stub improve the passband selectivity greatly. Two half wavelength long fractal Hilbert resonators are embedded near I/O line to achieve notch bands at 5.1 and 5.9 GHz. Aperture‐backed interdigital coupled‐lines are implemented to improve the coupling. The proposed prototype is fabricated and tested. The measured insertion loss is observed to be within 1.5 dB over the passband. By virtue of two transmission zeros (TZs), on either side of the passband, at 5.1 and 5.9 GHz, respectively, the passband selectivity is achieved with measured roll‐off factor at around 34 dB/octave. The out‐of‐band rejection of the filter is greater than 22 dB up to 18 GHz. The simulated results are in good agreement with the measured responses.     

A balanced dual‐band bandpass filter with independently tunable differential‐mode frequencies

A balanced dual‐band bandpass filter (BPF) with independently tunable differential‐mode (DM) frequencies is proposed in this letter. The proposed BPF is composed of complementary split‐ring resonators (CSRRs) etched on the ground and varactors loaded on the resonators. A balanced stepped‐impedance microstrip‐slotline transition structure is introduced to transfer the DM signals successfully and block the common‐mode (CM) signals transmission. Good DM transmission and CM suppression can be achieved. Moreover, by changing the reverse bias voltages of the varactors loaded on coupling CSRRs, two DM resonant frequencies of the proposed balanced BPF can be tuned independently. To verify the feasibility of the design method, a balanced BPF with DM frequency ranging from 0.80 GHz to 1.12 GHz and 1.55 GHz to 2.05 GHz is fabricated and measured. Good agreement between the simulation and measurement results demonstrate the validity of the design.     

Dual‐band band pass filter using stub‐loaded open‐loop resonators with wide controllable bandwidths

Two dual‐band band pass filters (BPF) using stub‐loaded open‐loop (SLOL) resonator are presented in this article. A novel coupling tuning method by changing the relative coupling position of the resonators is proposed to control the bandwidth of each passband in a wide range. Transmission zeros are created to improve the selectivity by source‐load coupling. Because of the large ratio of two bandwidths, a novel dual‐band matching method is proposed to match the different load impedances at two passband frequencies to the same source impedance. Hence, relax the fabrication requirement of gap. The proposed dual‐band band pass filter is designed and fabricated. The measured 3 dB fractional bandwidths (FBWs) of two 2.45/5.25 GHz dual‐band BPFs are 6.5%/14.5% and 9.8%/5.5%, respectively. The results are in good agreement with the simulation. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:367–374, 2014.     

A balanced dual‐band BPF with independently controllable frequencies and bandwidths

A balanced second‐order dual‐band bandpass filter (BPF) with independently controllable center frequencies and bandwidths based on coupled stepped‐impedance resonators (SIRs) is designed in this article. To obtain a dual‐band differential‐mode (DM) response, two pairs of SIRs with different resonant frequencies are employed in the design. The bandwidths of the two DM passbands can be independently tuned by adjusting the coupling gaps and coupling lengths of the corresponding resonators. In addition, three transmission zeros are realized to enhance the selectivity of the DM passbands. The microstrip‐slotline transition structure is utilized to achieve a wideband common‐mode (CM) suppression. Moreover, the DM responses are independent of the CM ones, which significantly simplify the design procedure. Finally, a balanced dual‐band BPF is designed to validate the design method and a good agreement between the simulated and measured results is observed.     

Ultracompact two‐way and four‐way SIW/HMSIW power dividers loaded by complementary split‐ring resonators

In this paper, two ultracompact power dividers based on the substrate integrated waveguide (SIW) and half‐mode SIW (HMSIW) technologies loaded by complementary split‐ring resonators (CSRRs) are presented. The presented structures are designed based on the theory of evanescent mode propagation. To obtain a size reduction, the CSRR unit cells are etched on the metallic surface of the SIW and HMSIW structures. First, a two‐way HMSIW power divider is reported. In this circuit, the concept of HMSIW is utilized aiming at a further size reduction in addition to the size reduction by the CSRR unit cells. Then, a four‐way SIW power divider is designed so that the direct coaxial feed is used for the input port and microstrip transmission lines are used for the output ports. Both two‐way and four‐way SIW/HMSIW power dividers at 5.8 GHz covering WLAN are designed, fabricated, and measured. They respectively have 0.18 × 0.21 λg² and 0.38 × 0.21 λg² total size. A fair agreement between simulated and measured results is achieved. The measured insertion losses are 0.5 ± 0.5 and 0.6 ± 0.5 dB for the two‐way and four‐way SIW/HMSIW power dividers, respectively, in the operating band of interest.     

A multi‐stub loaded compact UWB BPF with a broad notch band and extended stopband characteristics

A compact ultrawideband (UWB) bandpass filter (BPF) employing the principle of multiple mode resonance characteristics to create UWB passband with high selectivity and simultaneously having extensive stopband characteristic is presented. Utilizing five stubs attached along with the asymmetric trisection stepped impedance resonator (ATSSIR), the proposed resonator enables seven transmission poles inside the passband. As an additional attributes the projected filter triggers one transmission zero at 5.0 GHz which helps to mitigate WLAN signal interference. No additional circuitry is used to generate a notch band. The proposed prototype of UWB BPF is fabricated and estimated. Simulated and estimated results are in great understanding. The prospective filter displays a deliberate passband from 2.9 to 11.02 GHz. The filter unveils deceptive free wide upper stop band attributes till 25 GHz with least attenuation of 10 dB all through the stop band.     

Compact dual‐ and triband bandpass filter using frequency selecting coupling structure loaded stepped‐impedance resonator

This article presents two novel resonators, that is, frequency selecting coupling structure loaded stepped‐impedance resonator (FSCSLSIR) and π‐section loaded FSCSLSIR. The resonator behaviors and guidelines are given to design FSCSLSIR dual‐band bandpass filter (BPF) and π‐section loaded FSCSLSIR triband BPF. The proposed dual‐ and triband BPF have very compact sizes of 0.13 λ_gd × 0.06 λ_gd and 0.115 λ_gt × 0.074 λ_gt, respectively. Moreover, good return loss, low insertion loss, and high band‐to‐band isolation can be observed, and the proposed FSCSLSIR dual‐band BPF has an ultrawide stopband from 5.79 to 36 GHz. The experimental results are in good agreement with the simulations. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:427–435, 2015.     

A WLAN band‐notched compact four element UWB MIMO antenna

A compact four‐element multiple‐input‐multiple‐output (MIMO) antenna for ultra‐wideband (UWB) applications with WLAN band‐notched characteristics is proposed here. The proposed antenna has been designed to operate from 2 to 12 GHz while reject the frequencies between 4.9 to 6.4 GHz. The four antenna elements are placed orthogonal to attain the polarization diversity and high isolation. A thin stub connected to the ground plane is deployed as a LC notch filter to accomplish the rejected WLAN band in each antenna element. The mutual coupling between the adjacent elements is at least 17 dB while it has low indoor and outdoor envelop correlation (<0.45) and high gain with compact size of two boards, each measuring 50 × 25 mm². To validate the concept, the prototype antenna is manufactured and measured. The comparison of the simulation results showed good agreement with the measured results. The low‐profile design and compact size of the proposed MIMO antenna make it a good candidate for diversity applications desired in portable devices operating in the UWB region.     

Compact bandpass filter based on SIW loaded by open complementary split‐ring resonators

A compact substrate integrated waveguide (SIW) with open complementary split‐ring resonators (OCSRRs) loaded on the waveguide surface is proposed. The OCSRRs can be interpreted in terms of electric dipoles and they are good candidates to behave as electric scatterers. By loading OCSRRs on the waveguide surface, a forward‐wave pass‐band propagating below the waveguide cutoff frequency is generated. The resonance frequency of the OCSRRs is approximately half of the resonance frequency of the complementary split ring resonator (CSRR). Therefore, the electrical size of this particle is larger than the CSRRs and the OCSRRs are more appropriate for the SIW miniaturization. A bandpass response with a sharp rejection frequency band is obtained by properly manipulating the structure of the elements. By changing the orientation of the OCSRRs, two types of unit cell are proposed. Moreover, by resizing the OCSRRs, resonance frequency can be easily moved and the bandwidth can be tuned by the coupling between two OCSRRs. Compared with some other reported bandpass filters (BPFs) with SIW technique, the presented BPF has great improvements on size reduction and selectivity. To verify the methodology, two filters with center frequency of 5.5 GHz are designed and measured. The measured results are in good agreement with the simulated ones. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:674–682, 2016.     

Multi‐mode resonators with quad‐/penta‐/sext‐mode resonant characteristics and their applications to bandpass filters

In this article, a new class of dual‐/tri‐band and ultra‐wideband (UWB) bandpass filters (BPFs) using novel multi‐mode resonators are proposed. The classical even‐/odd‐mode method is applied to analyze the resonant characteristics of the proposed resonators, which exhibit controllable resonant modes with different dimension parameters under the same configuration. According to the analysis, three resonators with quad‐/penta‐/sext‐mode resonant characteristics are obtained by choosing the specific dimension parameters. Then, the quad‐mode resonator is used to design a dual‐wideband BPF centred at 2.39/5.14 GHz with 3‐dB fractional bandwidths (FBWs) of 36.9%/18.9%, and the penta‐mode resonator is utilized to design an UWB BPF with 3‐dB FBW of 102.2%, whereas the sext‐mode resonator is applied to design a tri‐band BPF with centre frequencies of 2.09/3.52/5.46 GHz and 3‐dB FBWs of 11.3%/20%/12.1%. All these three filters are fabricated and measured, and the measured results are in good agreement with the simulated ones.     

Design of high selectivity tri‐band bandpass filter with wide upper stopband

This article presents a dual‐plane structure high selectivity tri‐band bandpass filter (BPF) which consists of a pair of T‐shaped microstrip feed lines with capacitive source‐load coupling as well as spur lines embedded, and three resonators, i.e., a dual‐mode stub‐loaded stepped impedance resonator and two nested dual‐mode defected ground structure resonators. Using the intrinsic characteristics of the resonators and feed lines, nine transmission zeros near the passband edges and in the stopband can be generated to achieve high selectivity. An experimental tri‐band BPF located at 2.4/5.7 GHz [wireless local area networks (WLAN) application] and 3.5 GHz [worldwide interoperability for microwave access (WiMAX) application] has been simulated and fabricated. Good agreement between the simulated and measured results validates the design approach. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

Design of a compact dual‐band folded‐waveguide bandpass filter using multilayer waveguide resonators

A novel compact dual‐band bandpass filter based on multilayer folded‐waveguide (FWG) structure is presented in this article.In this design, slots are used to realize direct coupling between adjacent resonators and apertures are adopted to implement cross coupling between non‐adjacent resonators.A new technique of external quality factor of FWG resonator and coupling coefficients between different resonators are studied using full‐wave simulator. In order to demonstrate the proposed technique, a four‐pole dual‐band bandpass filter is designed, fabricated and measured using vector network analyzer. Measurement results which are well agreed with simulation results are presented. Moreover, four‐pole substrate integrated folded waveguide SIFW dual‐band bandpass filter, using two layers of slotted folded waveguide resonators, is demonstrated. The proposed filter has a compact size and it is excellent candidate for the application of wireless communication systems. © 2015 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:780–788, 2015.     

A novel super compact half‐mode substrate‐integrated waveguide filter using modified complementary split‐ring resonator

A novel super compact filter based on half‐mode substrate‐integrated waveguide (HMSIW) technology loaded by the modified complementary split‐ring resonator (MCSRR) is proposed. The working principle of the proposed filter is based on the evanescent‐mode propagation technique. According to this technique, by loading the complementary split‐ring resonator (CSRR) on the metal surface of the substrate‐integrated waveguide (SIW) structure, an additional passband below the SIW cutoff frequency can be obtained. In order to miniaturize the physical size of the conventional CSRR, a new method is introduced. In the proposed MCSRR unit‐cell, the meander slots are carved inside all of the interior space of the ring. Accordingly, the length of the slot is increased which leads to an increase in the inductor and capacitor of the proposed structure without occupying the extra space. Therefore, the electrical size of the proposed MCSRR unit‐cell is reduced. Consequently, the resonance frequency of the proposed MCSRR unit‐cell is decreased compared to the conventional CSRR with the same sizes. Namely, the lower resonance frequencies can be achieved by using this technique without increasing the size of the unit‐cell. In order to confirm the miniaturization technique, two HMSIW filters loaded by the proposed MCSRR unit‐cell are designed, fabricated, and experimental verifications are provided. The results show that a miniaturization about 67% is achieved.     

A balanced tri‐band bandpass filter with high selectivity and controllable bandwidths

In this article, a balanced tri‐band bandpass filter (BPF) with high selectivity and controllable bandwidths is proposed. Two differential‐mode (DM) passbands are formed by applying stepped impedance resonators into the design. Uniform impedance resonators are introduced to realize the third DM passband. Moreover, frequencies and bandwidths of DM passbands can be independently controlled by the lengths of resonators and the gaps between them. In addition, good DM transmission can be realized while high common‐mode suppression is achieved intrinsically without affecting the DM parts, thereby simplifying the design procedure significantly. In order to validate the practicability, a balanced tri‐band BPF operating at 2.45 GHz, 3.5 GHz, and 4.45 GHz is fabricated and designed. A good agreement between the simulated and measured results is observed.     

A tunable balanced dual‐band BPF with quasi‐independently controlled center frequency and bandwidth

In this paper, a balanced dual‐band bandpass filter (BPF) with high selectivity and low insertion loss performance is presented by employing stub loaded resonators (SLRs) and stepped impedance resonators (SIRs) into balanced microstrip‐slotline (MS) transition structures. The balanced MS transition structures can achieve a wideband common‐mode (CM) suppression which is independent of the differential‐mode (DM) response, significantly simplifying the design procedure. Six varactors are loaded into the resonators to achieve the electrical reconfiguration. The proposed balanced dual‐band BPF can realize quasi‐independently tunable center frequencies and bandwidths. A tuning center frequency from 2.48 to 2.85 GHz and a fractional bandwidth (20.16%‐7.02%) with more than 15 dB return loss and less than 2.36 dB insertion loss are achieved in the first passband. The second passband can realize a tuning center frequency from 3.6 to 3.95 GHz with more than 12 dB return loss and less than 2.38 dB insertion loss. A good agreement between the simulated and measured results is observed.     

Inter‐digital coupled dual‐mode patch resonator with crossed‐island configuration for tri‐band filter design

The miniaturized dual‐mode tri‐band band‐pass filters (BPF) using crossed‐island patch resonator is proposed in this article. The BPF is mainly formed by a square patch resonator in which a crossed‐island configuration is embedded in the patch. The patch size reduction with 74.4% is achieved. By the perturbation and the alternative inter‐digital coupling, the tri‐band responses are obtained. The proposed filter covers the required bandwidths for WLAN band (2.26–3.11 GHz and 5.02–6.0 GHz) and X‐band (7.58–8.41 GHz) applications. Five transmission zeros are placed between three pass‐bands and resulted in a good isolation. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:457–463, 2014.     

A compact printed ultra‐wideband multiple‐input multiple‐output prototype with band‐notch ability for WiMAX,LTEband43, and WLAN systems

A compact ultra‐wideband multiple‐input multiple‐output (UWB‐MIMO) antenna with good isolation and multiple band‐notch abilities is developed in this work. It consists of two quadrant shaped monopole antennas backed by ground stubs. A good isolation is achieved due to the two proposed extended curved ground stubs. The frequency rejection for the WLAN system is realized by loading a capacitive loaded loop resonator adjacent to the feed line. The band rejection for the WiMAX and LTE band43 system is achieved by embedding a quadrant shaped CSRR on each radiator's surface. The measured bandwidth of the antenna is 3.06 GHz‐11 GHz (|S₁₁| < ?10 dB and |S₂₁| < ?18 dB) with a band rejection from 3.5 GHz‐4 GHz to 5.1 GHz‐5.85 GHz, respectively. Time domain performances are investigated in terms of group and phase delay characteristics. Diversity characteristics are evaluated in terms of the envelope correlation coefficient, mean effective gain, and channel capacity loss.