A Fenton-like degradation mechanism for 1,4-dioxane using zero-valent iron (Fe) and UV light

In this study, the degradation mechanism of 1,4-dioxane using zero-valent iron (Fe⁰) in the presence of UV light was investigated kinetically. The degradation of 1,4-dioxane in Fe⁰-only, photolysis, and combined Fe⁰ and UV reactions followed the kinetics of a pseudo-first-order model. The degradation rate constant (19 × 10⁻⁴ min⁻¹) in the combined reaction with UV-C (4.2 mW cm⁻²) and Fe⁰ (5 mg L⁻¹) was significantly enhanced compared to Fe⁰-only (4.8 × 10⁻⁴ min⁻¹) and photolytic reactions (2.25 × 10⁻⁴ min⁻¹), respectively. The removal efficiency of 1,4-dioxane in combined reaction with Fe⁰ and UV within 4 h was enhanced by increasing UV intensity at UV-C region (34% at 4.2 mW cm⁻² and 89% at 16.9 mW cm⁻²) comparing with the removal in the combined reaction with Fe⁰ and UV-A (29% at 2.1 mW cm⁻², and 33% at 12.6 mW cm⁻²). It indicates that 1,4-dioxane was degraded mostly by OH radicals in the combined reaction. The degradation patterns in both Fe⁰-only and combined reactions were well fitted to the Langmuir-Hinshelwood model, implying that adsorption as well as the chemical reaction occurred. The transformation of Fe⁰ to Fe²⁺ and Fe³⁺ was observed in the Fe⁰-only and combined reactions, and the transformation rate of Fe⁰ was improved by UV irradiation. Furthermore, the reduction of Fe³⁺ was identified in the combined reaction, and the reduction rate was enhanced by an increase of UV energy. Our study demonstrated that the enhancement of 1,4-dioxane removal rate occurred via an increased supply of OH radicals from the Fenton-like reaction induced by the photolysis of Fe⁰ and H₂O, and with producing less sludge.     

Inactivation of environmental mycobacteria by free chlorine and UV

The resistance of environmental mycobacteria (EM) against chlorine and ultraviolet (UV) was evaluated for determination of the Ct value and UV dose to inactivate EM. Chlorine disinfection experiments were done on Mycobacterium fortuitum in oxidant demand-free buffered water at the worst condition (pH 8.5, 4 °C) and normal condition (pH 7.0, 20 °C). The Ct value for 3 log inactivation of M. fortuitum was 600 times greater than that of Escherichia coli. UV experiments were performed for various species of Mycobacterium avium, M. fortuitum, Mycobacterium intracellulare, and Mycobacterium lentiflavum. A UV collimated beam device was used for irradiation of four species suspended in phosphate buffered saline with doses of 5, 10, 20, 50, and 100 mJ/cm². UV sensitivity of mycobacteria was species-specific. More than 3 log of M. avium, M. intracellulare, and M. lentiflavum could be inactivated at 20 mJ/cm², whereas M. fortuitum was so resistant that 3 log inactivation required a dose of more than 50 mJ/cm². Mycobacteria were found 2-10 times more resistant to UV than E. coli for 3 log inactivation. There was no significant difference in the inactivation of mycobacteria with either low-pressure or medium-pressure UV irradiation.     

Effects of UV/H2O2 advanced oxidation on chemical characteristics and chlorine reactivity of surface water natural organic matter

The advanced oxidation process utilizing ultraviolet and hydrogen peroxide (UV/H₂O₂) is currently applied in commercial drinking water applications for the removal of various organic pollutants. Natural organic matter (NOM) present in the source water can also be oxidized and undergo changes at the fluence and H₂O₂ concentrations applied in commercial drinking water UV/H₂O₂ applications (fluences less than 2000 mJ cm⁻², initial H₂O₂ concentrations less than 15 mg L⁻¹). In this study, the impact of UV/H₂O₂ on NOM’s aromaticity, hydrophobicity, and potential to form trihalomethanes (THMs) and haloacetic acids (HAAs) was investigated for raw surface water and the same water with the very hydrophobic acid (VHA) fraction of NOM removed. During UV/H₂O₂ treatments, NOM in the raw surface water was partially oxidized to less aromatic and hydrophobic characteristics, but was not mineralized, confirming findings from past research. Below fluences of 1500 mJ cm⁻² UV/H₂O₂ treatment of the raw water did not lead to reduction in the formation potential of THMs. The formation potential of HAAs was reduced at a fluence of 500 mJ cm⁻² with only small additional reductions as fluence further increased. For the water from which the VHA fraction was removed, UV/H₂O₂ treatment led to mineralization of NOM suggesting that, when coupled with a pre-treatment capable of removing the VHA fraction, UV/H₂O₂ could achieve further reductions in NOM. These subsequent reductions in NOM led to continuous reductions in the formation potentials of THMs and HAAs as fluence increased.     

Aerobic degradation of sulfanilic acid using activated sludge

This paper evaluates the aerobic degradation of sulfanilic acid (SA) by an acclimatized activated sludge. The sludge was enriched for over three months with SA (>500 mg/L) as the sole carbon and energy source and dissolved oxygen (DO, >5 mg/L) as the primary electron acceptor. Effects of aeration rate (0-1.74 L/min), DO concentration (0-7 mg/L) and initial SA concentration (104-1085 mg/L) on SA biodegradation were quantified. A modified Haldane substrate inhibition model was used to obtain kinetic parameters of SA biodegradation and oxygen uptake rate (OUR). Positive linear correlations were obtained between OUR and SA degradation rate (R² ≥ 0.91). Over time, the culture consumed more oxygen per SA degraded, signifying a gradual improvement in SA mineralization (mass ratio of O₂: SA at day 30, 60 and 120 were 0.44, 0.51 and 0.78, respectively). The concomitant release of near stoichiometric quantity of sulphate (3.2 mmol SO₄²⁻ released from 3.3 mmol SA) and the high chemical oxygen demand (COD) removal efficacy (97.1%) indicated that the enriched microbial consortia could drive the overall SA oxidation close to a complete mineralization. In contrast to other pure-culture systems, the ammonium released from the SA oxidation was predominately converted into nitrate, revealing the presence of ammonium-oxidizing bacteria (AOB) in the mixed culture. No apparent inhibitory effect of SA on the nitrification was noted. This work also indicates that aerobic SA biodegradation could be monitored by real-time DO measurement.     

Protection against UV disinfection of E. coli bacteria and B. subtilis spores ingested by C. elegans nematodes

Nematodes, which occur abundantly in granular media filters of drinking water treatment plants and in distribution systems, can ingest and transport pathogenic bacteria and provide them protection against chemical disinfectants. However, protection against UV disinfection had not been investigated to date.In this study, Caenorhabditis elegans nematodes (wild-type strain N2) were allowed to feed on Escherichia coli OP50 and Bacillus subtilis spores before being exposed to 5 and 40 mJ/cm² UV fluences, using a collimated beam apparatus (LP, 254 nm). Sonication (15 W, 60 s) was used to extract bacteria from nematode guts following UV exposure in order to assess the amount of ingested bacteria that resisted the UV treatment using a standard culture method. Bacteria located inside the gut of C. elegans were shown to benefit from a significant protection against UV. Approximately 15% of the applied UV fluence of 40 mJ/cm² (as typically used in WTP) was found to reach the bacteria located inside nematode guts based on the inactivation of recovered bacteria (2.7 log reduction of E. coli bacteria and 0.7 log reduction of B. subtilis spores at 40 mJ/cm²). To our knowledge, this study is the first demonstration of the protection effect of bacterial internalization by higher organisms against UV treatment, using the specific case of E. coli and B. subtilis spores ingested by C. elegans.     

Anatoxin-a degradation by Advanced Oxidation Processes: Vacuum-UV at 172 nm, photolysis using medium pressure UV and UV/H2O2

Two Advanced Oxidation Processes, namely vacuum-ultraviolet (VUV) photolysis at 172 nm and ultraviolet/hydrogen peroxide (UV/H₂O₂) were investigated for the degradation of anatoxin-a in aqueous solutions. Solutions of anatoxin-a-fumarate were treated with VUV light at 172 nm with a UV dose of 200 mJ/cm², where fumaric acid served as a reference compound for a competition kinetics analysis. The second-order rate constant for the reaction between anatoxin-a and the hydroxyl radical was found to be (5.2 ± 0.3) × 10⁹ M⁻¹ s⁻¹ and was independent of pH, temperature, and initial concentration of anatoxin-a. The direct photolysis of anatoxin-a using a medium pressure (MP) UV lamp was also investigated, in which case a UV dose of 1285 mJ/cm² was required to degrade anatoxin-a by 88% and 50% at concentrations of 0.6 mg/L and 1.8 mg/L of toxin, respectively. Treatment of anatoxin-a with a low pressure (LP) UV lamp in the presence of 30 mg/L of H₂O₂ was examined, where it was found that more than 70% of toxin could be degraded at a UV dose of 200 mJ/cm². The degradation arises from the oxidation of the toxin by hydroxyl radicals. The addition of H₂O₂ clearly enhanced the degradation of anatoxin-a, up to a concentration of 40 mg/L, after which addition of more H₂O₂ had little effect on the degradation kinetics of anatoxin-a. The effect of background constituents in the water on the degradation of anatoxin-a was also investigated using natural and synthetically produced model waters.     

Photoinitiated oxidation of geosmin and 2-methylisoborneol by irradiation with 254 nm and 185 nm UV light

The degradation of geosmin and 2-methylisoborneol (2-MIB) by UV irradiation at different wavelengths was investigated under varying boundary conditions. The results showed that conventional UV radiation (254 nm) is ineffective in removing these compounds from water. In contrast to the usual UV radiation UV/VUV radiation (254 + 185 nm) was more effective in the removal of the taste and odour compounds. The degradation could be described by a simple pseudo first-order rate law with rate constants of about 1.2 × 10⁻³ m² J⁻¹ for geosmin and 2-MIB in ultrapure water. In natural water used for drinking water abstraction the rate constants decreased to 2.7 × 10⁻⁴ m² J⁻¹ for geosmin and 2.5 × 10⁻⁴ m² J⁻¹ for 2-MIB due to the presence of NOM. Additionally, the formation of the by-product nitrite was studied. In the UV/VUV irradiation process up to 0.6 mg L⁻¹ nitrite was formed during the complete photoinitiated oxidation of the odour compounds. However, the addition of low ozone doses could prevent the formation of nitrite in the UV/VUV irradiation experiments.     

Comparison of toxicity and release rates of Cu and Zn from anti-fouling paints leached in natural and artificial brackish seawater

Biocide-containing anti-fouling paints are regulated and approved according to the added active ingredients, such as Cu. Biocide-free paints are considered to be less environmentally damaging and do not need an approval. Zn, a common ingredient in paints with the potential of causing adverse effects has received only minor attention. Laboratory experiments were conducted in artificial brackish seawater (ASW) and natural brackish seawater (NSW) to quantify release rates of Cu and Zn from biocide-containing and biocide-free labeled eroding anti-fouling paints used on commercial vessels as well as leisure boats. In addition, organisms from three trophic levels, the crustacean Nitocra spinipes, the macroalga Ceramium tenuicorne and the bacteria Vibrio fischeri, were exposed to Cu and Zn to determine the toxicity of these metals. The release rate of Cu in NSW was higher from the paints for professional use (3.2-3.6 µg cm⁻² d^− 1) than from the biocide leaching leisure boat paint (1.1 µg cm⁻² d^− 1). Biocide-free paints did leach considerably more Zn (4.4-8.2 µg cm⁻² d^− 1) than biocide-containing leisure boat paint (3.0 µg cm⁻² d^− 1) and ship paints (0.7-2.0 µg cm⁻² d^− 1). In ASW the release rates of both metals were notably higher than in NSW for most tested paints. The macroalga was the most sensitive species to both Cu (EC₅₀ = 6.4 µg l^− 1) and Zn (EC₅₀ = 25 µg l^− 1) compared to the crustacean (Cu, LC₅₀ = 2000 µg l^− 1 Zn, LC₅₀ = 890 µg l^− 1), and the bacteria (Cu, EC₅₀ = 800 µg l^− 1 and Zn, EC₅₀ = 2000 µg l^− 1). The results suggest that the amounts of Zn and Cu leached from anti-fouling paints may attain toxic concentrations in areas with high boat density. To fully account for potential ecological risk associated with anti-fouling paints, Zn as well as active ingredients should be considered in the regulatory process.     

Degradation of bromoxynil and trifluralin in natural water by direct photolysis and UV plus H2O2 advanced oxidation process

The degradation of two pesticides, bromoxynil and trifluralin, was investigated in ultrapure and natural water solutions under ultraviolet (UV) light and a combination of UV and hydrogen peroxide (H₂O₂). The effect of pH on the photooxidation of the pesticides was also studied. The results indicated that under direct photolysis with monochromatic light at 253.7 nm and different conditions, the photochemical rates followed first-order kinetics, with fluence-based rate constants ranging from 9.15 × 10⁻⁴ to 6.37 × 10⁻³ cm² mJ⁻¹ and 7.63 × 10⁻³ to 1.47 × 10⁻² cm² mJ⁻¹ for bromoxynil and trifluralin, respectively. Quantum yields, in the range of 0.08-0.25 for bromoxynil and 0.12-0.72 for trifluralin, were observed in experiments using ultrapure water. The study also found that the UV/H₂O₂ process enhanced the oxidation rate in comparison to direct photolysis. A 90% degradation with UV dose of 333 and 188 mJ cm⁻² was achieved for bromoxynil and trifluralin, respectively, in natural water, in presence of 8.8 × 10⁻⁴ M H₂O₂. To assess the aquatic toxicity, the Microtox^® 81.9% screening test protocol was used before and after treatment. The test results indicated a decrease in the acute toxicity of the samples after treatment for both pesticides.     

Immediate and long-term impacts of UV-C irradiation on photosynthetic capacity, survival and microcystin-LR release risk of Microcystis aeruginosa

In this study, the immediate and long-term impacts of shortwave ultraviolet (UV-C) irradiation on photosynthetic capacity, survival, and recovery of Microcystis aeruginosa were investigated. The risk of microcystin-LR (MC-LR) release during irradiation was also estimated. The cell density was determined by a flow cytometry, and typical chlorophyll fluorescence parameters, including the effective quantum yield, photosynthetic efficiency and maximal electron transport rate, were measured by a pulse amplitude modulated (PAM) fluorometer. Under various UV-C dosages (140-4200 mJ cm⁻²), photosynthetic capacities were reduced, to different degrees, accompanied by slight cytoclasis and complete degradation of extracellular MC-LR immediately after irradiation. In a 6-d cultivation following UV-C irradiation, cell density and extracellular MC-LR in the samples treated by 140 mJ cm⁻² UV-C irradiation increased from 4.0 × 10⁶ cells mL⁻¹ and 8 μg L⁻¹ to 5.1 × 10⁶ cells mL⁻¹ and 20 μg L⁻¹, respectively. Significant M. aeruginosa cytoclasis (cell density from 4.0 × 10⁶ to 1.0 × 10⁶ cells mL⁻¹) and MC-LR release (2-25 μg L⁻¹) occurred when the UV-C dosage reached 350 mJ cm⁻². Cell cytoclasis and MC-LR release were enhanced in the cultivated samples under higher UV-C dosages. Results revealed that photosynthetic parameters were useful tools to predict the recovery profiles of M. aeruginosa cells, and the MC-LR release risk should be considered after UV-C inactivation.     

Infectivity of Giardia lamblia cysts obtained from wastewater treated with ultraviolet light

Several waterborne outbreaks of giardiasis have been linked to discharge of wastewater effluents into surface water. Little is known about the infectivity of Giardia lamblia cysts present in UV treated wastewater effluents. In this study, the infectivity of G. lamblia cysts, recovered from primary effluent and secondary effluent, both upstream and downstream of operating full-scale UV reactors at four wastewater treatment plants, was assessed using the Mongolian gerbil model. Infectivity of cysts obtained from the primary effluents was scored as either strong or moderate for induction of infection in gerbils at three out of four wastewater treatment plants. G. lamblia recovered from secondary effluent both upstream and downstream of the UV reactors caused weak infections in the gerbils. The probability of weak infections caused by inoculums of 50-1400 cysts per gerbil was, on the average, reduced by approximately 10% at the four wastewater UV installations with coliform reduction equivalent doses ranging from 6 to 18 mJ/cm². The UV systems provided considerably less inactivation of the parasite than expected based on the UV dose response of Giardia reported in the literature.     

Solar radiation disinfection of drinking water at temperate latitudes: Inactivation rates for an optimised reactor configuration

Solar radiation-driven inactivation of bacteria, virus and protozoan pathogen models was quantified in simulated drinking water at a temperate latitude (34°S). The water was seeded with Enterococcus faecalis, Clostridium sporogenes spores, and P22 bacteriophage, each at ca 1 × 10⁵ m L⁻¹, and exposed to natural sunlight in 30-L reaction vessels. Water temperature ranged from 17 to 39 °C during the experiments lasting up to 6 h. Dark controls showed little inactivation and so it was concluded that the inactivation observed was primarily driven by non-thermal processes. The optimised reactor design achieved S₉₀ values (cumulative exposure required for 90% reduction) for the test microorganisms in the range 0.63-1.82 MJ m⁻² of Global Solar Exposure (GSX) without the need for TiO₂ as a catalyst. High turbidity (840-920 NTU) only reduced the S₉₀ value by <40%. Further, when all S₉₀ means were compared this decrease was not statistically significant (prob. > 0.05). However, inactivation was significantly reduced for E. faecalis and P22 when the transmittance of UV wavelengths was attenuated by water with high colour (140 PtCo units) or a suboptimally transparent reactor lid (prob. < 0.05). S₉₀ values were consistent with those measured by other researchers (ca 1-10 MJ m⁻²) for a range of waters and microorganisms. Although temperatures required for SODIS type pasteurization were not produced, non-thermal inactivation alone appeared to offer a viable means for reliably disinfecting low colour source waters by greater than 4 orders of magnitude on sunny days at 34°S latitude.     

Multiple site study of recent atmospheric metal (Pb, Zn and Cu) deposition in the NW Iberian Peninsula using peat cores

In order to estimate atmospheric metal deposition in Southern Europe since the beginning of the Industrial Period (~ 1850 AD), concentration profiles of Pb, Zn and Cu were determined in four ²¹⁰Pb-dated peat cores from ombrotrophic bogs in Serra do Xistral (Galicia, NW Iberian Peninsula). Maximum metal concentrations varied by a factor of 1.8 for Pb and Zn (70 to 128 μg g⁻¹ and 128 to 231 μg g⁻¹, respectively) and 3.5 for Cu (11 to 37 μg g⁻¹). The cumulative metal inventories of each core varied by a factor of 3 for all analysed metals (132 to 329 μg cm⁻² for Pb, 198 to 625 μg cm⁻² for Zn and 22 to 69 μg cm⁻² for Cu), suggesting differences in net accumulation rates among peatlands. Although results suggest that mean deposition rates vary within the studied area, the enhanced ²¹⁰Pb accumulation and the interpretation of the inventory ratios (²¹⁰Pb/Pb, Zn/Pb and Cu/Pb) in two bogs indicated that either a record perturbation or post-depositional redistribution effects must be considered. After correction, Pb, Zn and Cu profiles showed increasing concentrations and atmospheric fluxes since the mid-XX^th century to maximum values in the second half of the XX^th century. For Pb, maximum fluxes were observed in 1955-1962 and ranged from 16 to 22 mg m⁻² yr⁻¹ (mean of 18 ± 1 mg m⁻² yr⁻¹), two orders of magnitude higher than in the pre-industrial period. Peaks in Pb fluxes in Serra do Xistral before the period of maximum consumption of leaded petrol in Europe (1970s-1980s) suggest the dominance of local pollutant sources in the area (i.e. coal mining and burning). More recent peaks were observed for Zn and Cu, with fluxes ranging from 32 to 52 mg m⁻² yr⁻¹ in 1989-1996, and from 4 to 9 mg m⁻² yr⁻¹ in 1994-2001, respectively. Our results underline the importance of multi-core studies to assess both the integrity and reliability of peat records, and the degree of homogeneity in bog accumulation. We show the usefulness of using the excess ²¹⁰Pb inventory to distinguish between differential metal deposition, accumulation or anomalous peat records.     

Degradation of selected pharmaceuticals in aqueous solution with UV and UV/H2O2

The degradation of four pharmaceutical compounds (PhACs), ibuprofen (IBU), diphenhydramine (DP), phenazone (PZ), and phenytoin (PHT) was investigated via ultraviolet (UV) photolysis and UV/H₂O₂ process with a low-pressure (LP) UV lamp. For each PhAC tested, direct photolysis quantum yields at 254 nm were found to be ranging from 6.32 × 10⁻² to 2.79 × 10⁻¹ mol E⁻¹ at pH 7. The second-order rate constants of the reaction between the PhACs and OH were determined to be from 4.86 × 10⁹ to 6.67 × 10⁹ M⁻¹ s⁻¹ by using a competition kinetic model which utilized para-chlorobenzoic acid (pCBA) as a reference compound. The overall effect of OH radical scavenging from humic acid (HA) and anions HCO₃⁻, NO₃⁻ was measured utilizing R_OH,UV method through examining the aqueous photodegradation of pCBA as a probe compound. Moreover, these fundamental direct and indirect photolysis parameters were applied in the model prediction for oxidation rate constants of the PhACs in UV/H₂O₂ process. It was found that the predicted oxidation rate constants approximated the observed ones. The results indicated that the new R_OH,UV probe compound method was applicable for measuring background OH radical scavenging effects in water treatment process of UV/H₂O₂. Furthermore, by GC-MS analysis, most of the intermediates created during the photodegradation of the selected PhACs in UV/H₂O₂ process were identified. For the photodegradation of PZ, a competition mechanism existed between the direct UV photolysis and the oxidation of OH. An appropriate dosage of H₂O₂ could hinder the occurrence of the direct photolysis.     

Application of the Nernst-Planck approach to lead ion exchange in Ca-loaded Pelvetia canaliculata

Ca-loaded Pelvetia canaliculata biomass was used to remove Pb²⁺ in aqueous solution from batch and continuous systems. The physicochemical characterization of algae Pelvetia particles by potentiometric titration and FTIR analysis has shown a gel structure with two major binding groups - carboxylic (2.8 mmol g⁻¹) and hydroxyl (0.8 mmol g⁻¹), with an affinity constant distribution for hydrogen ions well described by a Quasi-Gaussian distribution. Equilibrium adsorption (pH 3 and 5) and desorption (eluents: HNO₃ and CaCl₂) experiments were performed, showing that the biosorption mechanism was attributed to ion exchange among calcium, lead and hydrogen ions with stoichiometry 1:1 (Ca:Pb) and 1:2 (Ca:H and Pb:H). The uptake capacity of lead ions decreased with pH, suggesting that there is a competition between H⁺ and Pb²⁺ for the same binding sites. A mass action law for the ternary mixture was able to predict the equilibrium data, with the selectivity constants α_Ca^H = 9 ± 1 and α_Ca^Pb = 44 ± 5, revealing a higher affinity of the biomass towards lead ions. Adsorption (initial solution pH 4.5 and 2.5) and desorption (0.3 M HNO₃) kinetics were performed in batch and continuous systems. A mass transfer model using the Nernst-Planck approximation for the ionic flux of each counter-ion was used for the prediction of the ions profiles in batch systems and packed bed columns. The intraparticle effective diffusion constants were determined as 3.73 × 10⁻⁷ cm² s⁻¹ for H⁺, 7.56 × 10⁻⁸ cm² s⁻¹ for Pb²⁺ and 6.37 × 10⁻⁸ cm² s⁻¹ for Ca²⁺.     

Sediment reworking rates in deep sediments of the Mediterranean Sea

Different pelagic areas of the Mediterranean Sea have been investigated in order to quantify physical and biological mixing processes in deep sea sediments. Herein, results of eleven sediment cores sampled at different deep areas (> 2000 m) of the Western and Eastern Mediterranean Sea are presented.²¹⁰Pb_xs and ¹³⁷Cs vertical profiles, together with ¹⁴C dating, are used to identify the main processes characterising the different areas and, finally, controlling mixing depths (SML) and bioturbation coefficients (D_b). Radionuclide vertical profiles and inventories indicate that bioturbation processes are the dominant processes responsible for sediment reworking in deep sea environments.Results show significant differences in sediment mixing depths and bioturbation coefficients among areas of the Mediterranean Sea characterised by different trophic regimes. In particular, in the Oran Rise area, where the Almeria-Oran Front induces frequent phytoplankton blooms, we calculate the highest values of sediment mixing layers (13 cm) and bioturbation coefficients (0.187 cm² yr⁻¹), and the highest values of ²¹⁰Pb_xs and ¹³⁷Cs inventories. Intermediate values of SML and D_b (~ 6 cm and ~ 0.040 cm² yr⁻¹, respectively) characterise the mesothrophic Algero-Balearic basin, while in the Southern Tyrrhenian Sea mixing parameters (SML of 3 cm and D_b of 0.011 cm² yr⁻¹) are similar to those calculated for the oligotrophic Eastern Mediterranean (SML of 2 cm and D_b of ~ 0.005 cm² yr⁻¹).     

Contribution from the primary and secondary sources to the atmospheric formaldehyde in Kolkata, India

A novel and straight forward method is adopted to segregate the contribution of primary and secondary sources of formaldehyde based on the rates of its formation and removal at different times in the urban atmosphere of Kolkata. To achieve the above objective, the diurnal and seasonal mixing ratios of formaldehyde were measured during dry season at two busy roadside locations. The maximal secondary formation fluxes of formaldehyde during summer and winter were found to be 6.63 × 10⁷ and 1.23 × 10⁷ molecules cm^− 3 s^− 1, respectively. Apart from formaldehyde (C₁), several other carbonyls were quantified in this study. An overall good correlation between acetaldehyde (C₂) and propanal (C₃) indicates the contribution of vehicular emission to the carbonyl budget. The secondary formaldehyde contributions in summer and winter were about 71% and 32%, respectively. The relative mean contributions of C₁, C₂ and ozone towards generation of OH fluxes in summer were found to be 1.56 × 10⁷, 6.96 × 10⁵, and 1.29 × 10⁷ molecules cm^− 3 s^− 1, respectively, which were 3.2, 3.4 and 1.6 times higher than those in winter.     

Rhizosphere acidification of faba bean, soybean and maize

Interspecific facilitation on phosphorus uptake was observed in faba bean/maize intercropping systems in previous studies. The mechanism behind this, however, remained unknown. Under nitrate supply, the difference in rhizosphere acidification potential was studied by directly measuring pH of the solution and by visualizing and quantifying proton efflux of roots between faba bean (Vicia faba L. cv. Lincan No.5), soybean (Glycine max L. cv. Zhonghuang No. 17) and maize (Zea mays L. cv. Zhongdan No.2) in monoculture and intercrop, supplied without or with 0.2 mmol L^− 1 P as KH₂PO₄. The pH of the nutrient solution grown faba bean was lower than initial pH of 6.0 from day 1 to day 22 under P deficiency, whereas the pH of the solution with maize was declined from day 13 after treatment. Growing soybean increased solution pH irrespective of P supply. Under P deficiency, the proton efflux of faba bean both total (315.25 nmol h^− 1 plant^− 1) and specific proton efflux (0.47 nmol h^− 1 cm^− 1) was greater than that those of soybean (21.80 nmol h^− 1 plant^− 1 and 0.05 nmol h^− 1 cm^− 1, respectively). Faba bean had much more ability of rhizosphere acidification than soybean and maize. The result can explain partly why faba bean utilizes sparingly soluble P more effectively than soybean and maize do, and has an important implication in understanding the mechanism behind interspecific facilitation on P uptake by intercropped species.     

Threshold concentrations of biomass and iron for pressure drop increase in spiral-wound membrane elements

In a model feed channel for spiral-wound membranes the quantitative relationship of biomass and iron accumulation with pressure drop development was assessed. Biofouling was stimulated by the use of tap water enriched with acetate at a range of concentrations (1-1000 μg C l⁻¹). Autopsies were performed to quantify biomass concentrations in the fouled feed channel at a range of Normalized Pressure Drop increase values (NPD_i). Active biomass was determined with adenosinetriphosphate (ATP) and the concentration of bacterial cells with Total Direct Cell count (TDC). Carbohydrates (CH) were measured to include accumulated extracellular polymeric substances (EPS). The paired ATP and CH concentrations in the biofilm samples were significantly (p < 0.001; R² = 0.62) correlated and both parameters were also significantly correlated with NPD_i (p < 0.001). TDC was not correlated with the pressure drop in this study. The threshold concentration for an NPD_i of 100% was 3.7 ng ATP cm⁻² and for CH 8.1 μg CH cm⁻². Both parameters are recommended for diagnostic membrane autopsy studies. Iron concentrations of 100-400 mg m⁻² accumulated in the biofilm by adsorption were not correlated with the observed NPD_i, thus indicating a minor role of Fe particulates at these concentrations in fouling of spiral-wound membrane.