Preparation and performance analysis of barium titanate incorporated in corn starch‐based polymer electrolytes for electric double layer capacitor application

Polymer electrolyte membranes composing of corn starch as host polymer, lithium perchlorate (LiClO₄) as salt, and barium titanate (BaTiO₃) as composite filler are prepared using solution casting technique. Ionic conductivity is enhanced on addition of BaTiO₃ by reducing the crystallinity and increasing the amorphous phase content of the polymer electrolyte. The highest ionic conductivity of 1.28 × 10^?2 S cm^?1 is obtained for 10 wt % BaTiO₃ filler in corn starch‐LiClO₄ polymer electrolytes at 75°C. Glass transition temperature (T_g) of polymer electrolytes decreases as the amount of BaTiO₃ filler is increased, as observed in differential scanning calorimetry analysis. Scanning electron microscopy and thermogravimetric analysis are employed to characterize surface morphological and thermal properties of BaTiO₃‐based composite polymer electrolytes. The electrochemical properties of the electric double‐layer capacitor fabricating using the highest ionic conductivity polymer electrolytes is investigated using cyclic voltammetry and charge‐discharge analysis. The discharge capacitance obtained is 16.22 F g^?1. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43275.     

Influence of LiClO4 on the thermal,mechanical, and morphological properties of P(DMS‐co‐EO)/ P(EPI‐co‐EO) blends

The UV‐vis absorption, thermal analysis, ionic conductivity, mechanical properties, and morphology of a blend of poly(dimethylsiloxane‐co‐ethylene oxide) [P(DMS‐co‐EO)] and poly(epichlorohydrin‐co‐ethylene oxide) [P(EPI‐co‐EO)] (P(DMS‐co‐EO)/P(EPI‐co‐EO) ratio of 15/85 wt %) with different concentrations of LiClO₄ were studied. The maximum ionic conductivity (σ = 1.2 × 10^?4 S cm^?1) for the blend was obtained in the presence of 6% wt LiClO₄. The crystalline phase of the blend disappeared with increasing salt concentration, whereas the glass transition temperature (T_g) progressively increased. UV‐vis absorption spectra for the blends with LiClO₄ showed a transparent polymer electrolyte in the visible region. The addition of lithium salt decreased the tensile strength and elongation at break and increased Young's modulus of the blends. Scanning electron microscopy showed separation of the phases between P(DMS‐co‐EO) and P(EPI‐co‐EO), and the presence of LiClO₄ made the blends more susceptible to cracking. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1230–1235, 2004     

Optimization of PVC– PAN‐based polymer electrolytes

The hybrid plasticized polymer electrolyte composed of the blend of poly(vinyl chloride) (PVC) and poly(acrylonitrile) (PAN) as host polymer, propylene carbonate as plasticizer, and LiClO₄ as a salt was studied. An attempt was made to optimize the polymer blend ratio. XRD, Fourier transform infrared, and DSC studies confirm the formation of polymer–salt complex and miscibility of the PVC and PAN. The electrical conductivity and temperature dependence of ionic conductivity of polymer films are also studied and reported here. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Crystallinity,thermal properties,morphology and conductivity of quaternary plasticized PEO‐based polymer electrolytes

Quaternary plasticized solid polymer electrolyte (SPE) films composed of poly(ethylene oxide), LiClO₄, Li_1.3Al_0.3Ti_1.7(PO₄)₃, and either ethylene carbonate or propylene carbonate as plasticizer (over a range of 10–40 wt%) were prepared by a solution‐cast technique. X‐ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS) indicated that components such as LiClO₄ and Li_1.3Al_0.3Ti_1.7(PO₄)₃ and the plasticizers exerted important effects on the plasticized quaternary SPE systems. XRD analysis revealed the influence from each component on the crystalline phase. DSC results demonstrated the greater flexibility of the polymer chains, which favored ionic conduction. SEM examination revealed the smooth and homogeneous surface morphology of the plasticized polymer electrolyte films. EIS suggested that the temperature dependence of the films' ionic conductivity obeyed the Vogel–Tamman–Fulcher (VTF) relation, and that the segmental movement of the polymer chains was closely related to ionic conduction with increasing temperature. The pre‐exponential factor and pseudo activation energy both increased with increasing plasticizer content and were maximized at 40 wt% plasticizer content. The charge transport in all polymer electrolyte films was predominantly reliant on lithium ions. All transference numbers were less than 0.5. Copyright © 2006 Society of Chemical Industry     

Solid polymer electrolytes. XI. Preparation,characterization and ionic conductivity of new plasticized polymer electrolytes based on chemical‐covalent polyether–siloxane hybrids

A new hybrid polymer electrolyte system based on chemical‐covalent polyether and siloxane phases is designed and prepared via the sol–gel approach and epoxide crosslinking. FT‐IR, ¹³C solid‐state NMR, and thermal analysis (differential scanning calorimetry (DSC) and TGA) are used to characterize the structure of these hybrids. These hybrid films are immersed into the liquid electrolyte (1M LiClO₄/propylene carbonate) to form plasticized polymer electrolytes. The effects of hybrid composition, liquid electrolyte content, and temperature on the ionic conductivity of hybrid electrolytes are investigated and discussed. DSC traces demonstrate the presence of two second‐order transitions for all the samples and show a significant change in the thermal events with the amount of absorbed LiClO₄/PC content. TGA results indicate these hybrid networks with excellent thermal stability. The EDS‐0.5 sample with a 75 wt % liquid electrolyte exhibits the ionic conductivity of 5.3 × 10^?3 S cm^?1 at 95°C and 1.4 × 10^?3 S cm^?1 at 15°C, in which the film shows homogenous and good mechanical strength as well as good chemical stability. In the plot of ionic conductivity and composition for these hybrids containing 45 wt % liquid electrolyte, the conductivity shows a maximum value corresponding to the sample with the weight ratio of GPTMS/PEGDE of 0.1. These obtained results are correlated and used to interpret the ion conduction behavior within the hybrid networks. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1000–1007, 2006     

Physical and electrochemical properties of low molecular weight poly(ethylene glycol)‐bridged polysilsesquioxane organic–inorganic composite electrolytes via sol–gel process

A new class of ionic conducting organic/inorganic hybrid composite electrolyte with high conductivity, better electrochemical stability and mechanical behavior was prepared through the sol–gel processing between ethylene‐bridged polysilsesquioxane and poly(ethylene glycol) (PEG). The composite electrolyte with 0.05 LiClO₄ per PEG repeat unit has the best conductivity up to 10^?4 S/cm at room temperature with the transference number up to 0.48 and an electrochemical stability window as high as 5.5 V versus Li/Li⁺. Moreover, the effect of the PEG chain length on the properties of the composite electrolyte has also been studied. The interactions between ions and polymer have also been investigated for the composite electrolyte in the presence of LiClO₄ by means of FTIR, DSC, and TGA. The results indicated the interaction of Li⁺ ions with the ether oxygen of the PEG, and the formation of transient crosslinking with LiClO₄, resulting in an increase of the T_g of the composite electrolyte. The VTF‐type behavior of the ionic conductivity implied that the diffusion of the charge carriers was assisted by the segmental motions of the polymer chains. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2752–2758, 2007     

Solid polymer electrolytes VIII: effect of LiClO4-doped level on the microstructure and ionic conductivity of a chemical-covalently polyether-siloxane hybrid electrolyte

A new hybrid polymer electrolyte system based on chemical-covalently polyether and siloxane phases is designed and prepared in the presence of lithium perchlorate (LiClO₄) which acted as both ionic source and the epoxide ring-opening catalyst. The effect of salt-doped level on the microstructure and ionic conductivity of these composite electrolytes were investigated by means of Fourier transform infra-red spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis, a.c. impedance and multinuclear solid-state nuclear magnetic resonance measurements. DSC results indicate that the formation of transient cross-links between Li⁺ ions and the ether oxygens on complexation with LiClO₄ results in an increase in polyether segment T_g. However, the polyether segment T_g decreases at the highest salt concentration (5.0 mmol LiClO₄/g PEGDE), ascribing to the plasticizing effect. The behavior of ion transport is coupled with the segmental motions of polymer chains and also correlated with the interactions between ions and polymer host.     

Solid polymer electrolytes V: microstructure and ionic conductivity of epoxide-crosslinked polyether networks doped with LiClO4

A crosslinked polyether network was prepared from poly(ethylene glycol) diglycidyl ether (PEGDE) cured with poly(propylene oxide) polyamine. Significant interactions between ions and polymer host have been observed for the crosslinked polyether network in the presence of LiClO₄ by means of FT-IR, DSC, TGA, and ⁷Li MAS solid-state NMR. Thermal stability and ionic conductivity of these complexes were also investigated by TGA and AC impedance measurements. The results of FT-IR, DSC, TGA and ⁷Li MAS solid-state NMR measurements indicate the formation of different types of complexes through the interaction of ions with different coordination sites of polymer electrolyte networks. The dependence of ionic conductivity was investigated as a function of temperature, LiClO₄ concentration and the molecular weight of polyether curing agents. It is observed that the behavior of ion transport follows the empirical Vogel-Tamman-Fulcher (VTF) type relationship for all the samples, implying the diffusion of charge carrier is assisted by the segmental motions of polymer chains. Moreover, the conductivity is also correlated with the interactions between ions and polymer host, and the maximum ionic conductivity occurs at the LiClO₄ concentration of [O]/[Li⁺]=15.     

Solid polymer electrolytes. VII. Preparation and ionic conductivity of gelled polymer electrolytes based on poly(ethylene glycol) diglycidyl ether cured with α,ω‐diamino poly(propylene oxide)

Crosslinked polymer electrolyte networks were prepared from poly(ethylene glycol) diglycidyl ether blended with an epoxy resin (diglycidyl ether of bisphenol A) in different ratios and then cured with α,ω‐diamino poly(propylene oxide) in the presence of lithium perchlorate (LiClO₄) as a lithium salt. The ionic conductivities of these polymer electrolytes were determined by alternating current (AC) impedance spectroscopy. Propylene carbonate (PC) was used as a plasticizer to form gelled polymer electrolyte networks. The conductivities of the polymer electrolytes containing 46 wt % PC plasticizer were approximately 5 × 10^?4 S cm^?1 at 25°C and approximately 10^?3 S cm^?1 at 85°C. These polymer electrolytes were homogeneous and exhibited good mechanical properties. The effects of the polymer composition, plasticizer content, salt concentration, and temperature on the ionic conductivities of the polymer electrolytes were examined. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1264–1270, 2004     

Fabrication and characterization of a solid polymeric electrolyte of PAN‐TiO2‐LiClO4

The ionic conductivity of PAN‐TiO₂‐LiClO₄ as a function of TiO₂ concentration and temperature has been reported. The electrolyte samples were prepared by solution casting technique. Their conductivity was measured using the impedance spectroscopy technique. The highest room temperature conductivity of 1.8 × 10^?4 S cm^?1 was obtained at 7.5 wt % of TiO₂ filler. It was observed that the relationship between temperature and conductivity were linear, fitting well in Arrhenius and not in Vogel‐Tamman‐Fulcher equation. The pre‐exponential factor, σ₀ and E_a are 1.8 × 10^?4 S cm^?1 and 0.15 eV, respectively. The conductivity data have been supported by differential scanning calorimeter (DSC) analysis. DSC analysis showed that there was a significant change in glass transition temperature (T_g) with the filler concentration. The SEM micrograph revealed that the TiO₂ particles are dispersed in the electrolyte, thus enhancing its conductivity. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Composite polymer electrolytes based on the low crosslinked copolymer of linear and hyperbranched polyurethanes

Low crosslinked copolymer of linear and hyperbranched polyurethane (CHPU) was prepared, and the ionic conductivities and thermal properties of the composite polymer electrolytes composed of CHPU and LiClO₄ were investigated. The FTIR and Raman spectra analysis indicated that the polyurethane copolymer could dissolve more lithium salt than the corresponding polymer electrolytes of the non crosslinked hyperbranched polyurethane, and showed higher conductivities. At salt concentration EO/Li = 4, the electrolyte CHPU30‐LiClO₄ reached its maximum conductivity, 1.51 × 10^?5 S cm^?1 at 25°C. DSC measurement was also used for the analysis of the thermal properties of polymer electrolytes. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3607–3613, 2007     

Morphological,infrared, and ionic conductivity studies of poly(ethylene oxide)–49% poly(methyl methacrylate) grafted natural rubber–lithium perchlorate salt based solid polymer electrolytes

The potential of poly(ethylene oxide) (PEO) and 49% poly(methyl methacrylate) grafted natural rubber (MG49) as a polymer host in solid polymer electrolytes (SPE) was explored for electrochemical applications. PEO–MG49 SPEs with various weight percentages of lithium perchlorate salt (LiClO₄) was prepared with the solution casting technique. Characterization by scanning electron microscopy, Fourier transform infrared spectroscopy, and impedance spectroscopy was done to investigate the effect of LiClO₄ on the morphological properties, chemical interaction, and ionic conductivity behavior of PEO–MG49. Scanning electron microscopy analysis showed that the surface morphology of the sample underwent a change from rough to smooth with the addition of lithium salts. Infrared analysis showed that the interaction occurred in the polymer host between the oxygen atom from the ether group (C? O? C) and the Li⁺ cation from doping salts. The ionic conductivity value increased with the addition of salts because of the increase in charge carrier up to the optimum value. The highest ionic conductivity obtained was 8.0 × 10^?6 S/cm at 15 wt % LiClO₄. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

LiClO4 doped cellulose acetate as biodegradable polymer electrolyte for supercapacitors

The possibility of producing a biodegradable polymer electrolyte based on cellulose acetate (CA) with varied concentration of LiClO₄ for use in supercapacitors has been investigated. The successful doping of the CA films has been analyzed by FTIR and DSC measurements of the LiClO₄ doped CA films. The ionic conductivity of the films increased with increase in salt content and the maximum ionic conductivity obtained for the solid polymer electrolyte at room temperature was 4.9 × 10^?3 Ω^?1 for CA with 16% LiClO₄. The biodegradation of the solid polymer electrolyte films have been tested by soil burial, degradation in activated sludge, and degradation in buffer medium methods. The extent of biodegradation in the films has been measured by AC Impedance spectroscopy and weight loss calculations. The study indicated sufficient biodegradability of the materials. A p/p polypyrrole supercapacitor has been fabricated and its electrochemical characteristics and performance have been studied. The supercapacitor showed a fairly good specific capacitance of 90 F g^?1 and a time constant of 1 s. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphology and electrochemical and mechanical properties of polyethylene‐oxide‐based nanofibrous electrolytes applicable in lithium ion batteries

We report the synthesis of all‐solid‐state polymeric electrolytes based on electrospun nanofibers. These nanofibers are composed of polyethylene oxide (PEO) as the matrix, lithium perchlorate (LiClO₄) as the lithium salt and propylene carbonate (PC) as the plasticizer. The effects of the PEO, LiClO₄ and PC ratios on the morphological, mechanical and electrochemical characteristics were investigated using the response surface method (RSM) and analysis of variance test. The prepared nanofibrous electrolytes were characterized using SEM, Fourier transform infrared, XRD and DSC analyses. Conductivity measurements and tensile tests were conducted on the prepared electrolytes. The results show that the average diameter of the nanofibers decreased on reduction of the PEO concentration and addition of PC and LiClO₄. Fourier transport infrared analysis confirmed the complexation between PEO and the additives. The highest conductivity was 0.05 mS cm^?1 at room temperature for the nanofibrous electrolyte with the lowest PEO concentration and the highest ratio of LiClO₄. The optimum nanofibrous electrolyte showed stable cycling over 30 cycles. The conductivity of a polymer film electrolyte was 29 times lower than that of the prepared nanofibrous electrolyte with similar chemical composition. Furthermore, significant fading in mechanical properties was observed on addition of the PC plasticizer. The results obtained imply that further optimization might lead to practical uses of nanofibrous electrolytes in lithium ion batteries. © 2019 Society of Chemical Industry     

Blending poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) as composite polymer electrolyte

A blend of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (PSAN) has been evaluated as a composite polymer electrolyte by means of differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, ac impedance measurements, and linear sweep voltammetry (LSV). The blends show an interaction with the Li⁺ ions when complexed with lithium perchlorate (LiClO₄), which results in an increase in the glass‐transition temperature (T_g) of the blends. The purpose of using PSAN as another component of the blend is to improve the poor mechanical properties of PMMA‐based plasticized electrolytes. The mechanical property is further improved by introducing fumed silica as inert filler, and hence the liquid electrolyte uptake and ionic conductivity of the composite systems are increased. Room‐temperature conductivity of the order of 10^?4 S/cm has been achieved for one of the composite electrolytes made from a 1/1 blend of PSAN and PMMA containing 120% liquid electrolyte [1M LiClO₄/propylene carbonate (PC)] and 10% fumed silica. These systems also showed good compatibility with Li electrodes and sufficient electrochemical stability for safe operation in Li batteries. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1319–1328, 2001     

1H NMR,thermal, and conductivity studies on PVAc based gel polymer electrolytes

The lithium‐ion conducting gel polymer electrolytes (GPE), PVAc‐DMF‐LiClO₄ of various compositions have been prepared by solution casting technique. ¹H NMR results reveal the existence of DMF in the gel polymer electrolytes at ambient temperature. Structure and surface morphology characterization have been studied by X‐ray diffraction analysis (XRD) and scanning electron microscopy (SEM) measurements. Thermal and conductivity behavior of polymer‐ and plasticizer‐salt complexes have been studied by differential scanning calorimetry (DSC), TG/DTA, and impedance spectroscopy results. XRD and SEM analyses indicate the amorphous nature of the gel polymer‐salt complex. DSC measurements show a decrease in T_g with the increase in DMF concentrations. The thermal stability of the PVAc : DMF : LiClO₄ gel polymer electrolytes has been found to be in the range of (30–60°C). The dc conductivity of gel polymer electrolytes, obtained from impedance spectra, has been found to vary between 7.6 × 10^?7 and 4.1 × 10^?4 S cm^?1 at 303 K depending on the concentration of DMF (10–20 wt %) in the polymer electrolytes. The temperature dependence of conductivity of the polymer electrolyte complexes appears to obey the VTF behavior. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of novel crosslinked polyurethane–acrylate electrolyte

Flexible, transparent, and crosslinked polymer films were synthesized by polymerization of PEG‐modified urethane acrylate using a simple method. A series of novel solid polymer electrolytes and gel electrolytes were prepared based on this type of polymer film. To understand the interactions among salt, solvent, and polymer, the swelling behaviors of the crosslinked polymer in pure propylene carbonate (PC) and liquid electrolyte solutions (LiClO₄/PC) were investigated. The results showed that the swelling rate in the electrolyte solution containing moderate LiClO₄ was greater than that in pure PC. Thermogravimetric analysis (TGA) also supported the interaction between the solvent and polymer. The morphology and crystallinity of the crosslinked polymer and polymer electrolytes were studied using atomic force microscopy (AFM) and wide‐angle X‐ray diffraction (WAXD) spectroscopy. The effects of the content of the electrolyte solution on the ionic conductivity of gel electrolytes were explored. The dependence of the conductivity on the amount of the electrolyte solution was nonlinear. With a different content of the plasticizer, the ionic conduction pathway of the polymer electrolytes would be changed. The best ionic conductivity of the gel electrolytes, which should have good mechanical properties, was 4 × 10^r?3 S cm^?1 at 25°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 340–348, 2003     

Effect of the addition of hydrophobic clay on the electrochemical property of polyacrylonitrile/LiClO4 polymer electrolytes for lithium battery

In this study, an organoclay, ALA-MMT, was prepared by the ionic exchange reaction of montmorillonite (MMT) with 12-aminododecanoic acid (ALA). ALA-MMT was then used as a filler to prepare a series of composite polymer electrolytes based on polyacrylonitrile (PAN) and LiClO₄. The effect of the addition of ALA-MMT on the properties of the composite polymer electrolytes (CPEs) was investigated by XRD, FT-IR, DSC, tensile strength, AC impedance, and cyclic voltammetry measurements. It was found that the ALA-MMT particles were well dispersed in the CPEs. Owing to the incorporation of ALA-MMT, a higher fraction of the free anions was obtained, indicating that the lithium salt dissolved in the PAN matrix more effectively for the CPE than in the PAN/LiClO₄ polymer electrolyte. Moreover, the glass-transition temperature was reduced, benefiting the ion transport. The best ionic conductivity at room temperature was obtained from the CPE with 7 wt% of the modified clay and 0.6 M LiClO₄ per PAN repeat unit (CPE-7) and was more than seven times higher than that from the corresponding PAN/LiClO₄ polymer electrolyte (CPE-0). The mechanical property and the cation transference number, t₊, of CPE-7 are largely increased compared to that of CPE-0. Besides, the CPEs were electrochemically stabilized up to 4.75 V and the corresponding cell exhibited excellent electrochemical stability and cyclability over the potential range between 0 V and 4.0 V vs. Li/Li⁺.     

Characterization of (PEO)LiClO4‐Li1.3Al0.3Ti1.7(PO4)3 composite polymer electrolytes with different molecular weights of PEO

A group of polyethylene oxide (PEO)LiClO₄‐Li_1.3Al_0.3Ti_1.7(PO₄)₃ composite polymer electrolyte (CPE) films was prepared by the solution‐cast method. In each film, EO/Li = 8 and the Li_1.3Al_0.3Ti_1.7(PO₄)₃ content of 15 wt % were fixed, but the number averaged molecular weight of PEO (M_n) was altered from 5 to 7 × 10⁴ to 10⁶, 2.2–2.7 × 10⁶, 3–4 × 10⁶, 4–5 × 10⁶, and 5.5–6 × 10⁶, respectively. Several techniques including X‐ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and electrical impedance spectroscopy (EIS) were used to characterize the CPE films. LiClO₄ was found to have a strong tendency to complex with PEO, but Li_1.3Al_0.3Ti_1.7(PO₄)₃ was rather dispersed in PEO matrix. DSC analysis revealed that the amorphous phase was dominant in the CPE films although the PEOs before‐use was considerably crystalline. SEM study showed smooth and homogeneous morphologies of the films with low molecular weight PEO and a dual phase characteristic for those with high molecular weight PEO. EIS results indicated that the CPE films are all ionic conductor and the conducting behavior obeys Vogel‐Tamman‐Fulcher (VTF) equation. The parameters in VTF equation were obtained and discussed by taking into considerations PEO molecular weights and crystallinities of the CPE films. Of all the films, the one with PEO with the smallest M_n = 5–7 × 10⁴ had the maximum conductivity, i.e., 1.590 × 10^?5 S cm^?1 at room temperature and 1.886 × 10^?3 S cm^?1 at 373 K. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4269–4275, 2006     

Structure and ionic conductive properties of polydioxolane–polyurethane‐based electrolytes

A series of polyurethanes (PUs) with different polyether soft segments [polydioxolane (PDXL), polyethylene glycol (PEG), or PDXL/PEG] were synthesized successfully, and solid polymer electrolytes based on PU/LiClO₄ complexes were prepared. The relations between structure and the ionic conductive properties of the PU‐based electrolytes were investigated by means of Fourier transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical analysis, and complex impedance analysis. Results showed that the glass‐transition temperature (T_g) of PDXL–PU was lower than that of PEG–PU. Doped lithium perchlorate (LiClO₄) salt could be dissolved well in soft segments of PDXL–PU. The ionic conductivity of the PDXL–PU/LiClO₄ complex could reach a value of 2 × 10^?5 S/cm at room temperature without the addition of an organic plasticizer. The system with PDXL/PEG as a soft segment had a higher T_g and a lower ionic conductivity than the one with PDXL as a soft segment. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 103–111, 2002