立方形状态方程的相图分析

本文通过对修正Ω的R-K方程的数学分析,对根的取舍和判断作了明确的解释。通过对纯二氧化碳、二氧化碳-异丁烷以及二氧化碳-正癸烷体系的P-V相图分析,可以了解各相图区中的VL,Vv以及汽液两相共存区的准确位置和数值,及其可能导致的误差。     

从统计力学推导流体状态方程(Ⅲ)——关于马丁-侯状态方程等的统计力学证明与解释

本文从多方阱非球形势硬粒子微扰理论出发,通过适当的近似与化简,导出了马丁-侯状态方程,从而使这个由经验提出的状态方程得到了统计力学的证明与解释.从多方阱非球形势硬粒子微扰理论出发,通过更粗略的近似也能得到范德华状态方程以及Barner与Adler改进的(?)offie状态方程.由理论分析,马丁-侯方程较为全面,不仅有高级微扰项,保留了多级密度展开式,同时取用了较精确的多级参考流体状态方程.     

基于Patel-Teja状态方程的统一粘度模型(Ⅱ)应用于油气藏流体粘度的预测

基于(I)报根据pVT和Tμp图形的相似性和Patel-Teja状态方程建立的预测纯流体气、液相粘度的统一模型,通过引入常规的状态方程参数的混合规则,将其应用于二元轻烃混合物共计1894个数据点及模拟天然气高压粘度的预测,平均相对误差分别为13.78%和16.75%;应用于油藏原油和天然气高压粘度的预测,结果优于现有的有关油气藏流体粘度模型.     

有微扰理论研究链状流体的状态方程

本文用微扰理论建立了链状流体的分子热力学模型，并给出了体系Ｈｅｌｍｈｏｌｔｚ自由能函数及状态方程的表达式，对非级性流体，体系的热力学性质由硬球作用，成链作用及色散作用三部分组成。对极性链状流体，分子间作用还包括偶极作用及诱导作用。将此模型应用于正烷烃及正一元醇的计算，同时关联纯液体的密度和饱和蒸汽压，结果与实验值符合良好。本文中所用的参数具有明确的物理意义，与前人的工作相比较，本文理论处理简单并用     

由状态方程计算混合物的临界性质

混合物的临界性质(T_c,P_c和V_c)在高压相态及分离过程计算中具有重要意义.由于实验测定的困难,文献与手册中有关混合物临界性质的数据(与混合物组成有关)极少,如何通过计算确定这些性质成为热力学界所关心的问题之一.混合物的临界性质一般可通过以下三种方法进行估算:(1)通过相包线计算间接确定;(2)由经验或半经验关联式计算;(3)基于严格的临界状态的热力学准则应用状态方程直接计算.第一种方法过于繁琐;而第二种方法普适性较差,且缺乏与汽液平衡计算的热力学一致性;第三种直接计算法可消除上述缺点,因而近年来受到较大重视.Heidemann和Khalil(1980)以及Peng和Robinson(1977)所提出的直接计算法已成功地应用于烃类非极性混合物临界性质的预测.本文的目的主要是将直接法扩充应用至极性混合物临界性质的计算,并改进前人对临界比容的预测.在前阶段工作(徐东海和郭天民,1989)基础上,本文作了较大扩充与修改.按Heidemann和Khalil由Helmholtz自由能导出的下列临界状态判别准则Q△n=0,△n~T△n=1(1)及偏导数矩阵Q中的元素q_(ij)与三次式中三阶偏导数的表达式结合状态方程(可导出逸度f_i表达式)联解方程式(l)和(2)便可求得组成指定的混合物的临界性质.为将直接法扩展应用至极性混合物,作者选用了Leet等(1986)提     

修正的硬球三参数状态方程(Ⅱ)纯物质热力学性质的预测

对本文(I)报中MCSPT方程与物质有关的参数A_1、A_2、A_3、A_4和A_5给出了以偏心因子ω和临界压缩因子Z_c为关联因子的普遍化关联式,从而将MCSPT方程推广到极性、强极性物质热力学性质的预测.通过对72种物质饱和液体密度和151种物质液体蒸发焓的计算结果表明,MCSPT不仅能精确地预测物质的饱和性质,而且也能准确地计算焓差.     

动态电路的超回路分析法

提出了一个新的状态方程编写法——超回路法，它适用于含各种受控源的电路。最后，给出了一个实例。     

Scrap of magnesia parts,the reasons for it,and means of reducing it

Conclusions The most common and characteristic forms of scrap of magnesia parts differing in form, dimensions, and composition are shown. These include deviations of the dimensions from the nominal, breaking off of the corners and edges, nonuniformity, welding together, spots, voids, fire cracks, spalls, and cracks of different origin.The reasons for formation of scrap were determined. The primary of them are the reduced quality of the raw material (chromite, magnesite) with a larger quantity of impurities containing limited silicon and calcium oxides, sometimes insufficient density, grain size, and completeness of hydration of the magnesite powders, nonconformity of the bunker, proportioning, mixing, and pressing equipment to the requirements of modern production of progressive high-quality refractories, the insufficiently high binding capacity of lignosulfonates, deviations in the quality of assembly and finishing of press equipment and automatic ejectors, of the car floor lining, and in firing conditions, a high variation in density of the green parts, and nonuniform heating and cooling in the volume of the parts and of the whole charge during firing. More than 50% of the total scrap of all forms is due to firing scrap of parts.The primary means of reducing or eliminating scrap of parts and simultaneously increasing their quality based on the reasons for formation of different forms of it were noted. These above all else, are increasing the volumes and improving and introduction of new methods of concentration of magnesite and chromite, a successive increase in the share of chrome concentrates, chromium-containing broken parts, and powders by firing of magnesite and caustic dust in the production of magnesia refractory parts as the result of a decrease in the share of commercial natural chromite and magnesite, the use in the production of parts of high-quality type PMSP-93 powder produced in shaft kilns and used as the charge for production of fused materials, the use of the prospect of processes for production of dense periclase powders uniform in chemical analysis from recovered caustic dust, replacement of obsolete mixing and press equipment by more modern, increasing the strength of green parts by above all else improving the binding properties of LST and increasing pressing pressure, forming of the taper of parts by the side plates of the die, improving the quality of assembly and increasing the reliability of functioning of press equipment and automatic ejectors, improving car floor linings, introduction of new methods and increasing the volumes of production of progressive unfired refractories in place of certain forms of fired parts, observation of all production parameters, and a relationship of the wages of labor to the quantity of scrap and the quality of refractories.Introduction of the new management system and the active work of the quality groups created will open up and lead to the action of unutilized reserves for reduction of scrap.Translated from Ogneupory, No. 2, pp. 31–38, February, 1989.     

Special Features Of Stabilization Of The Growth Process In Plasma-arc Growth Of Single Crystals Of Refractory Compounds From SHS Products

Problems of the stability of the growth process in growing single crystals of refractory compounds (carbides and bondes of transition metals) by the method of plasma-arc remelting are considered. The main reasons behind the loss of stability of the spatial configuration of the melt (a shift of the anode lock-on of the arc from the center of the molten pool, disturbance of the symmetry of the plasma jet, superheating of the melt) are considered. The effect of cyclic perturbations in the crystallization system that appear upon replenishment on the fluctuation of the energy characteristics of the arc, the temperature of the melt, and the displacements of the crystallization surface is described. It is established that the crystallization rate and the process of coarsening of the crystallites in the formation of a columnar structure in the ingot depend on the frequency of feeding new portions and on their mass.     

Investigation of conditions of spherulite formation in mixtures of crystalline and amorphous polymers

The supermolecular structure of mixtures of crystalline polymers (low pressure and high pressure polyethylene, isotactic polypropylene) with an amorphous polymer (atactic polypropylene) from the point of view of the influence of the amorphous component on the morphology of the crystalline component has been investigated. The criterion of changes in the morphological state of larger supermolecular formations was the microscopic image of the samples obtained with an optical microscope, both between crossed nicols and in phase contrast. It has been established that the formation of typical spherulites depends on the amount of admixture of the amorphous polymer and also on the treatment of the samples. Upon crystallization in presence of a small amount of solvent (p-xylene), formation of typical spherulites of the crystalline component of the mixture can be observed while the same mixture in case of evaporation of the solvent presents a granulated refractive structure without typical spherulites, regardless of the rate of cooling. The probable role of the solvent is to facilitate mutual segregation of the microphases of both polymers in consequence of decrease in viscosity of the mixture. It has been further shown that even after briefly heating the mixture to a temperature of 220°C., before crystallization, spherulites do not form; on the contrary, spherulites originally present disappear and a structure consisting of smaller refractive formations of crystalline polymer is obtained. The formation of this structure, emerging after destruction of spherulites, might be attributed to an increase of interpenetration of both polymers and to an increase of the contact surfaces between components of the mixture.     

Some special features of open-hearth furnace bottoms

Conclusions The peculiar feature of the formation of hearths fettled with fine-grained chromemagnesite powder compared with those fettled with metallurgical magnesite powder is the formation of a more clearly expressed crystalline concretion of periclase as a result of the fine grain size composition of the powder and the presence in it of grains of chromite which help the process of hearth formation.Wear of the hearths made of chromemagnesite and magnesite powders is due mainly to one and the same factor — destruction of the crystalline concretion of periclase under the action of iron-silicate melt in the slag. The process of destruction of the hearths made from chromemagnesite powder occurs more slowly owing to the more complete formation of the concretion of crystals of periclase in these hearths, which is probably the basic cause of the higher resistance.Investigation of samples of hearth taken from the site of an accidental escape of metal through the bottom, showed that they contained crystals of iron spinel which is probably due to the local supersaturation of the hearth with iron oxides.     

聚羧酸减水剂影响抗裂性能的机理研究

通过实验,以混凝土28d的拉压比大小为评价混凝土抗裂性能的优劣，分析了合成聚羧酸减水剂的羧基、氨基、磺酸基、羟基、酯基等各官能团比例，聚醚支链的长短，减水剂分子量大小等因素对混凝土抗裂性能的影响。初步探讨了聚羧酸减水剂提高混凝土抗劈裂性能机理。     

Maternal Melatonin Deficiency Leads to Endocrine Pathologies in Children in Early Ontogenesis

The review summarizes the results of experimental and clinical studies aimed at elucidating the causes and pathophysiological mechanisms of the development of endocrine pathology in children. The modern data on the role of epigenetic influences in the early ontogenesis of unfavorable factors that violate the patterns of the formation of regulatory mechanisms during periods of critical development of fetal organs and systems and contribute to the delayed development of pathological conditions are considered. The mechanisms of the participation of melatonin in the regulation of metabolic processes and the key role of maternal melatonin in the formation of the circadian system of regulation in the fetus and in the protection of the genetic program of its morphofunctional development during pregnancy complications are presented. Melatonin, by controlling DNA methylation and histone modification, prevents changes in gene expression that are directly related to the programming of endocrine pathology in offspring. Deficiency and absence of the circadian rhythm of maternal melatonin underlies violations of the genetic program for the development of hormonal and metabolic regulatory mechanisms of the functional systems of the child, which determines the programming and implementation of endocrine pathology in early ontogenesis, contributing to its development in later life. The significance of this factor in the pathophysiological mechanisms of endocrine disorders determines a new approach to risk assessment and timely prevention of offspring diseases even at the stage of family planning.     

浅谈我国陶瓷产品出口反倾销数据动态预警系统的构建

本文首先从我国陶瓷产品贸易现状出发，阐述了建立我国陶瓷产品出口反倾销数据动态预警系统的意义，然后指出建立我国陶瓷产品出口反倾销数据动态预警系统的总体思路，并在此基础上论述建立我国陶瓷产品出口反倾销数据动态分析预警系统的主要步骤。     

Some problems of separation of mixtures

The paths of the development of research and the change of priorities in the area of separation of mixtures are tracked by the example of analysis of the works of the laboratory founded by N.M. Zhavoronkov in 1945. The studies performed encompass a wide range of basic problems of heat and mass transfer in gas absorption, distillation (including vacuum, molecular, etc.), fractional crystallization, and melting. The subjects of the works under consideration include separation of isotopes of light elements, design of mass-transfer apparatuses with high unit power, investigation of the mechanism and kinetics of separation processes, studies of separation enhancement methods, and development of hybrid energy-and resource-saving processes and equipment.     

Application of Sonic Moduli of Elasticity and Rigidity to Testing of Heavy Refractories

The application of A.S.T.M. C 215-51 T (Tentative Method of Test for Fundamental Transverse Frequency of Concrete Specimens for Calculating Young's Modulus of Elasticity) to the nondestructive testing of 1- by 1- by 7-in. laboratory fire-clay specimens and standard 9-in. fire-clay and high-alumina refractory brick is reviewed. Both room-temperature measurements and hot sonic modulus of elasticity measurements to 1700°F. are analyzed. Sonic moduli of elasticity and rigidity are compared with modulus of rupture by a theory of measurements and statistical analysis. The limits of uncertainty of the average of modulus of rupture are shown to be a function of the degree of verification whereas in the case of both sonic moduli they are not. Limits of uncertainty of the average of sonic moduli data are usually of the same order as errors calculated from the precision of measurements. In the case of modulus of rupture of well-vitrified clays, the uncertainty of the average is much greater than calculated error limits. Sonic moduli differentiate statistically between two samples of 60% alumina brick whereas modulus of rupture does not. If Poisson's ratio is assumed to be zero rather than the conventional one-sixth, ratios of sonic modulus of elasticity to rigidity are shown to approximate the theoretical ratio more closely. Effects of nonuniform density to displace normal nodes are illustrated. Hot sonic modulus of elasticity is shown to reflect changes due to crystallographic inversions, deterioration of chemical bond in unfired brick, and development of sintered bond in unfired brick.     

不脱蛋白质壳聚糖制备工艺

采用D -近似最优设计法系统地研究了NaOH质量分数、碱处理时间及碱处理温度这三个主要因素对制备壳聚糖的影响 :当碱液质量分数增加时 ,壳聚糖的脱乙酰度增加 ,但其速度却在减小 ,当碱液质量分数达到 40 %时 ,脱乙酰度出现峰值 ,约为 90 % ,而后增加碱液质量分数时 ,脱乙酰度反而下降 ;随着反应温度的升高 ,其脱乙酰度几乎线性递增 ,当温度达到 2 0 0℃附近时 ,曲线趋于平直并且脱乙酰度达到最大 ;随着反应时间的增加 ,脱乙酰度开始呈线性增加 ,当反应时间超过 5 0min后 ,脱乙酰度有下降趋势 ;在一定碱液质量分数 (4 0 % )条件下 ,脱乙酰度随着温度的增加而增加 ,因此 ,若需获得较高质量的壳聚糖 ,必须提高反应温度