甲醇水蒸汽重整制氢Au/TiO2催化剂

采用沉积-沉淀法制备了一系列Au/TiO2催化剂,考察了Au负载量、焙烧温度以及助剂等因素对甲醇水蒸汽重整制氢反应催化性能的影响;并利用XRD, TEM对催化剂进行了表征. 结果表明,制备条件对催化性能有明显影响;Au负载量为5%(w)时所得催化剂活性较好;助剂NiO可使催化剂催化甲醇水重整的催化活性明显提高;100℃烘干未焙烧制得的催化剂活性最好;TEM结果显示,NiO的加入使载体TiO2颗粒分散度提高,Au粒粒度变小.     

制备参数对Au/TiO_2催化剂上CO低温氧化性能的影响

以溶胶-凝胶法制备TiO2载体,用沉积-沉淀法制备出一系列负载型Au/TiO2。系统考察了焙烧温度、金的负载量、反应液pH值、沉淀剂种类以及Cl-存在与否等制备参数对催化剂活性的影响。以室温下CO的催化氧化为探针反应,确定催化剂的最适宜制备参数,并对优化的质量分数为1.0%的Au/TiO2催化剂进行了活性稳定性测试。结果表明：Au/TiO2的最适宜焙烧温度是200～350℃;反应液的最适宜pH值为9;最适宜沉淀剂是NaOH;金的负载量（质量分数,下同）在0.5%～5.0%范围内时,金含量越高,催化剂活性和热稳定性越好。大量Cl-的存在能导致催化剂活性的显著下降。对优化的Au/TiO2催化剂在室温下催化氧化不同浓度的CO进行循环测试,经历3次循环,连续反应2 160 min后,CO的转化率仍为100%。     

镍盐前体对Ni-Fe/γ-Al2O3催化剂甲烷化性能的影响

以3种不同镍盐(硝酸镍、乙酸镍和氯化镍)为前体,采用等体积浸渍法制备了双金属Ni-Fe/γ-Al2O3催化剂,分别记作Ni-Fe-N、Ni-Fe-Ac和Ni-Fe-Cl,在浆态床反应装置上对各催化剂CO甲烷化催化活性进行评价。结果表明,Ni-Fe-N甲烷化催化活性最高,CO转化率、CH4选择性分别为97.2%和87.3%;而Ni-Fe-Cl甲烷化催化活性最低,CO转化率、CH4选择性分别为47.3%和58.7%。通过XRD、H2-TPR和CO-TPD等表征技术探讨了催化剂的微观结构与甲烷化催化活性之间的关系,发现Ni-Fe-N甲烷化活性高的原因是NiO晶粒小、分散好,Ni与Fe之间具有较好的协同作用,并且CO吸附量大。     

Au/Fe2O3催化剂上CO选择氧化反应性能的研究

采用共沉淀法、沉积-沉淀法和浸渍法制备了1.5%Au/Fe2O3催化剂,考察了不同方法制备的Au/Fe2O3催化剂对富氢气体中CO选择氧化反应性能的影响。结果表明,浸渍法制得的催化剂在40℃~60℃时CO的转化率为100%;共沉淀法与沉积-沉淀法制得的催化剂在80℃以下CO的转化率均为100%;沉积-沉淀法制得的催化剂在100℃时CO的转化率依然高于95%。上述三种催化剂CO氧化反应的选择性均高于40%,且在CO完全转化时选择性在50%以上。     

Au/α-Fe2O3催化剂选择性氧化富氢气中CO的性能研究

通过并流共沉淀法制备了Au/-Fe2O3催化剂,考察了金负载量及焙烧温度对Au/-Fe2O3催化剂的物化结构及其选择性氧化富氢气体中CO催化性能的影响。研究结果表明,金负载量和焙烧温度对催化剂的性能均有较大影响,金负载量为1.5%(wt),低温焙烧(200~400℃)时制得的Au/-Fe2O3催化剂对CO选择性氧化反应具有很好的催化活性和选择性,其中金负载量为1.5%(wt)、300℃焙烧的Au/-Fe2O3催化剂,在40℃时对富氢气体中CO的转化率达到100%,选择性为 66%,该催化剂连续反应120h催化活性没有明显下降。XRD、BET和TEM分析结果表明,催化剂的性能与单质Au的粒径有关,粒径越小,催化活性越高。     

载体对镍系催化剂催化对硝基苯酚加氢制对氨基苯酚的影响

采用浸渍法制备了Ni/Al2O3、Ni/TiO2、Ni/活性炭和Ni/硅藻土等一系列镍系催化剂,研究了其催化对硝基苯酚加氢制备对氨基苯酚的活性.负载型镍系催化剂具有单一的对氨基苯酚选择性.不同载体负载的催化剂上对硝基苯酚的转化率顺序为:Ni/活性炭>Ni/硅藻土>Ni/TiO2Ni/Al2O3.高比表面积以及金属镍在活性炭上的良好分散性使得Ni/活性炭催化活性最高;NiO与硅藻土间弱相互作用,有助于提高活性;而NiO与Al2O3之间存在相互作用抑制了还原后金属镍的催化加氧活性.     

高硫合成气制甲硫醇K2MoO4/SiO2催化剂的研究Ⅰ.镍的促进作用

采用共同浸渍法制备了K2MoO4-NiO/SiO2催化剂,考察了NiO添加量对高硫合成气制甲硫醇K2MoO4/SiO2催化剂性能的影响.活性评价结果表明,添加了NiO的催化剂活性有很大的提高,当Ni/Mo物质的量比为2/9时,CO转化率为72.6%,较未添加NiO的催化剂提高了一倍多.程序升温还原(TPR)表征显示,添加的NiO与Mo有强相互作用,促进了Mo物种的还原.电子自旋共振(ESR)表征显示,反应后的催化剂中可检测到"oxo-Mo(V)"物种和"thio-Mo(V)"物种,K2MoO4-NiO/SiO2催化剂表面主要为"thio-Mo(V)"物种,而K2MoO4/SiO2催化剂表面主要为"oxo-Mo(V)"物种,NiO的添加促进了Mo物种的还原、硫化,可能是造成催化剂活性极大提高的原因.     

Au-Pt-Sn异丁烷脱氢催化剂的制备

以异丁烷为原料制取异丁烯是解决异丁烯稀缺和异丁烷浪费的双赢方法,异丁烷脱氢主要问题是催化剂的研发。国内外大量研究以Pt-Sn为活性组分,但仍然存在转化率偏低和容易失活等问题,而负载型纳米Au催化剂在低温时对CO氧化表现出很高的催化活性。在原有Pt-Sn催化剂基础上,加入Au,采用等体积浸渍法制备Au-Pt-Sn催化剂,比较Au对异丁烷脱氢催化剂转化率和选择性的影响,使用小型固定床不锈钢反应器,常压、温度600 ℃、空速2 400 h^-1和临氢条件下评价其性能。发现加入一定量Au后,增强了催化剂活性,n(Au)∶n(Pt)=1.0时,异丁烯收率大于40%。考察催化剂再生前后效果差异,发现经过再生后,异丁烷转化率和选择性略低有下降,表明催化剂可以再生利用。     

选择性催化还原脱硝催化剂研究进展

催化剂是选择性催化还原(selective catalytic reduction,SCR)脱硝技术的核心,催化剂的低温活性、选择性和稳定性直接影响到NOx的脱除效果.SCR脱硝催化剂性能主要取决于催化剂活性组分和催化剂载体.简述了以氨、尿素和碳氢化合物等不同物质作为SCR还原剂的化学反应原理;介绍了以贵金属(Pt,Pd,Rh,Au等)和金属氧化物(V2O5,WO3,FeaO3,CuO,CrOx,MnO2.MoO3和NiO等)为催化剂活性组分.以分子筛、柱撑黏土、碳基材料和TiO2等为催化剂载体的SCR脱硝催化剂的研究进展.以V2O3为主要活性组分,以TiO2为载体的钒钛类催化剂因其理想的综合性能,目前已商业化应用.纳米有序结构TiO2薄膜可望成为理想的SCR脱硝催化荆新型载体.     

Au基MOFs双功能催化剂的制备及其催化CO2与苯胺/H2反应性能

以UiO-66(Zr)、MIL-100(Fe)、MIL-100(Cr)、MIL-101(Cr)、NH 2-MIL-101(Al)为载体,Au为活性组分,制备Au/UiO-66(Zr)、Au/MIL-100(Fe)、Au/MIL-100(Cr)、Au/MIL-101(Cr)、Au/NH 2-MIL-101(Al)双功能催化剂。采用XRD、BET、NH 3-TPD、HRTEM等表征催化剂的结构,在釜式反应器中评价催化剂对CO 2与苯胺/H 2反应生成N-甲基苯胺与N,N-二甲基苯胺的N-甲基化反应性能,考察反应条件对催化剂催化性能的影响。结果表明,催化剂的XRD特征衍射峰与相应MOFs的模拟特征峰基本一致;负载Au后催化剂仍具有高的比表面积和大的孔容、孔径;不同MOFs负载Au的催化剂具有不同的酸强度和酸量;Au纳米粒子的分散性很好,粒径为(3~7)nm。制备的催化剂均具有催化CO2与苯胺/H2的N-甲基化反应性能,其中质量分数2%Au/MIL-101(Cr)催化剂催化性能最好,苯胺转化率为45.26%,N-甲基苯胺和N,N-二甲基苯胺选择性分别为73.50%和26.50%,重复使用性能优异。     

Polymorphism of LiGa5O8 and of LiGa5O8-MgGa2O4Solid Solutions

High-temperature X-ray diffraction and differential thermal analyses showed that LiGa₅O₈ exists in two polymorphs related by the first-order transition at 1138°±3°C of the low-temperature simple-cubic form, space group (probably) O⁷, to the high-temperature spinel (fcc) form, space group O _h ⁷. The transition is rapid, and the high-temperature form in pure LiGa₅O₈ could not be quenched to room temperature under the conditions used. However, the high-temperature polymorph can be quenched under equilibrium conditions when 40 mol% or more MgGa₂O₄ is present. The subsolidus equilibrium relations in the system MgGa₂O₄-LiGa₅O₈ are discussed.     

Magnetoresistance of CuxCo1-xFe2O4 Ferrites

Magnetoresistance measurements (Δ/R) were carried out on Cu _x Co_{1- x} Fe₂O₄ samples with x =1, 0.75, 0.50, 0.25 and cobalt ferrite in the range of magnetic intensity (H) from 1.0 to 4.5 kG. Linear plots were obtained between log (Δ/R) and log H for all compositions except that of cobalt ferrite. The values of n at x =0.5 do not agree with the results of some authors. The discrepancy may be attributed to the value of magnetic field intensity at which such measurements were carried out. The similarity of features of n and μ_D with composition leads us to believe that the magnetoresistance may arise from the scattering of conduction electrons by localized electrons involving the s-d exchange interaction.     

Sintering of Si3N4-Y2O3-Al2O3

Sintering kinetics of the system Si₃N4-Y2O₃-Al₂O3 were determined from measurements of the linear shrinkage of pressed disks sintered isothermally at 1500° to 1700°C. Amorphous and crystalline Si₃N₄ were studied with additions of 4 to 17 wt% Y₂O₃ and 4 wt% A1₂O₃. Sintering occurs by a liquid-phase mechanism in which the kinetics exhibit the three stages predicted by Kingery's model. However, the rates during the second stage of the process are higher for all compositions than predicted by the model. X-ray data show the presence of several transient phases which, with sufficient heating, disappear leaving mixtures of β ' -Si₃N₄ and glass or β '-Si₃N₄, α '-Si₃N₄, and glass. The compositions and amounts of the residual glassy phases are estimated.     

Effects of metal-support interactions on the hydrogenation of CO over PdSiO2 and PdLa2O3

A study of CO hydrogenation over $\text{Pd}\text{SiO}{}_2$ and $\text{Pd}\text{La}{}_2\text{O}{}_3$ has been carried out for the purpose of identifying the effects of Pd dispersion, Pd morphology, and support composition on the catalytic activity of supported Pd. The specific activity of each catalyst for methanol and methane synthesis was determined from microreactor studies carried out at a fixed set of reaction conditions. Palladium dispersion was measured by H₂O₂ titration, and the morphology of the Pd crystallites, as expressed by the distribution of Pd(100) and Pd(111) planes, was determined from in situ infrared spectra of adsorbed CO. The crystallite morphology of the $\text{Pd}\text{SiO}{}_2$ catalysts is the same, independent of Pd weight loading: 90% of the surface is comprised of Pd(100) planes and 10% of the surface is comprised of Pd(111) planes. By contrast, the crystallite morphology of the $\text{Pd}\text{La}{}_2\text{O}{}_3$ catalysts changes with Pd loading. Primarily Pd(100) planes are exposed at low-weight loadings while Pd(111) planes are exposed at high-weight loadings. The Pd dispersion has little effect on the methanol turnover frequency over both $\text{Pd}\text{SiO}{}_2$ and $\text{Pd}\text{La}{}_2\text{O}{}_3$, for dispersions between 10 and 20%. On the other hand, the methane turnover frequency is independent of Pd dispersion over $\text{Pd}\text{SiO}{}_2$, but increases with decreasing dispersion over $\text{Pd}\text{La}{}_2\text{O}{}_3$. It is further observed that the Pd morphology influences the specific activity of $\text{Pd}\text{La}{}_2\text{O}{}_3$ for methanol synthesis: Pd(100) is nearly threefold more active than Pd(111). For a fixed morphology, the specific methanol synthesis activity of $\text{Pd}\text{La}{}_2\text{O}{}_3$ is a factor of 7.5 greater than that of $\text{Pd}\text{SiO}{}_2$.     

Wet Milling of Fe/Al/Al2O3 and Fe2O3/Al/Al2O3 Powder Mixtures

Wet milling of Al₂O₃-aluminide alloy (3A) precursor powders in acetone has been investigated by milling Fe/Al/Al₂O₃ and Fe₂O₃/Al/Al₂O₃ powder mixtures. The influence of the milling process on the physical and chemical properties of the milled powders has been studied. Particle refinement and homogenization were found not to play a dominant role, whereas plastic deformation of the metal particles leads to the formation of dislocations and a highly disarranged polycrystalline structure. Although no chemical reactions among the powder components in Fe₂O₃/Al/Al₂O₃ powder mixtures were observed, the formation of a nanocrystalline, ordered intermetallic FeAl phase in Fe/Al/Al₂O₃ powder mixtures caused by mechanical alloying was detected. Chemical reactions of Fe and Al particle surfaces with the atmosphere and the milling media lead to the formation of highly porous hydroxides on the particle surfaces. Hence the specific surface area of the powders increases, while the powder density decreases during milling. The fraction of Fe oxidized during milling was determined to be 0.13. The fraction of Al oxidized during milling strongly depends on the metal content of the powder mixture. It ranges between 0.4 and 0.8.     

Expansive properties of the mixture C4ASH12 − 2CS III. Effects of temperature and restraint

The effects of temperature and restraint upon the hydration and the expansion of $\text{C}{}_4\text{A}\text{S}\text{H}{}_{12}\text{? 2}\text{C}\text{S}$ mixture compacts in different contact solutions have been investigated. Temperatures above 20°C do apparently hinder the formation of an impervious felt-like layer of ettringite around the $\text{C}{}_4\text{A}\text{S}\text{H}{}_{12}$ particles, thus greatly reducing the retarding effect of the lime. An uniaxial restraint of 1 Kg/cm² is enough to reduce sensibly the expansions which remain however high (about 100%). The results can be satisfactorily interpreted by the reaction and expansion mechanism hypothesized in our previous papers.     

Raman Study of Glasses of Ba2TiSi2O8 and Ba2TiGe2O8

Raman spectra are reported for fresnoite (Ba₂Ti(Si,Ge)₂O₈ glasses, and comparison is made between the Raman spectra of the corresponding crystalline powders and glasses of Ba₂TiSi₂O₈ and Ba₂TiGe₂O₈. The Ba₂TiGe₂O₈ glass spectra show correspondence with the Ba₂TiGe₂O₈ crystalline Raman spectra; the v _s(Ge–O–Ge) mode occurs at 518 cm⁻¹ in the glass and at 521 cm⁻¹ in the crystalline material. Five-fold coordinated titanium is the majority species present in the Ba₂TiGe₂O₈ glass as revealed by a strong band at 824 cm⁻¹ in the I glass spectrum. The Ba₂TiSi₂O₈ glass spectra are similar to the Ba₂TiSi₂O₈ crystalline spectrum; the strongest band is found at 836 cm⁻¹ in the I glass spectrum. Through comparison with the previous Raman data of other titania silicate glasses, we conclude that the Ba₂TiSi₂O₈ glass has a structure similar to the crystalline phase.     

Preparation and properties of poly(Nε,Nε-dicarboxymethyl-l-lysine)

A new ampholytic homopolypeptide, $\text{poly}\text{(N}{}^{\mathrm{\epsilon }}\text{,N}{}^{\mathrm{\epsilon }}\text{-}\text{dicarboxy-methyl-}\text{l}\text{-lysine}\text{)}$, which has one tertiary amino and two carboxyl groups in the side chain has been derived from a hydrochloride salt of poly(L-lysine). The polymer in aqueous solution seems to be in the coil form with locally extended structure (LES) at neutral pH. In both the acidic and alkaline regions, the molar ellipticity of the polymer changes as a result of change in net charge on the side chain. The conformational changes may be from the coil with LES to other coiled forms. 5–7 M NaClO₄ and 80% aqueous methanol induce the α-helix in the polymer at neutral pH. Divalent cations, Cu²⁺ and Ca²⁺, do not induce any remarkably ordered structures such as α-helix or β-structure in the polymer in aqueous solution at any pH. Ultraviolet absorption studies show an absorption peak of the polymer-Cu²⁺ complex near 240 nm. Dependence of the peak intensity on pH at various q values ($\text{q =}\text{[}\text{Cu}{}^{\mathrm{2+}}\text{]}\text{[}\text{residue}\text{]}$) indicates the two steps of the complex formation. At q less than 0.64, the formation is described only with the first step. An average coordination number for Cu²⁺ at the first step was calculated to be about 2 by the method of Mandel and Leyte. The association constant of Cu²⁺ with the residue at the step was determined from the absorption data to be far smaller than that for the Cu²⁺-EDTA complex. The second step of the formation occurs in the case of large q but the absorption data for the second step cannot be obtained exactly due to precipitation.