Cold spray of SiC and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> with soft metal incorporation: A technical contribution

Al + SiC, Al + Al₂O₃ composites as well as pure Al, SiC, and Al₂O₃ coatings were prepared on Si substrates by the cold gas dynamic spray process (CGDS or cold spray). The powder composition of metal (Al) and ceramic (SiC, Al₂O₃) was varied into 1:1 and 10:1 wt.%, respectively. The propellant gas was air heated up to 330 °C and the gas pressure was fixed at 0.7 MPa. SiC and Al₂O₃ have been successfully sprayed producing coatings with more than 50 μm in thickness with the incorporation of Al as a binder. Also, hard ceramic particles showed peening effects on the coating surfaces. In the case of pure Al metal coating, there was no crater formation on hard Si substrates. However, when Al mixed with SiC and Al₂O₃, craters were observed and their quantities and sizes depended on the composition, aggregation and size of raw materials.     

HVOF-Sprayed Coatings Engineered from Mixtures of Nanostructured and Submicron Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript> Powders: An Enhanced Wear Performance

In previous studies, it has been demonstrated that nanostructured Al₂O₃-13 wt.%TiO₂ coatings deposited via air plasma spray (APS) exhibit higher wear resistance when compared to that of conventional coatings. This study aimed to verify if high-velocity oxy-fuel (HVOF)-sprayed Al₂O₃-13 wt.%TiO₂ coatings produced using hybrid (nano + submicron) powders could improve even further the already recognized good wear properties of the APS nanostructured coatings. According to the abrasion test results (ASTM G 64), there was an improvement in wear performance by a factor of 8 for the HVOF-sprayed hybrid coating as compared to the best performing APS conventional coating. When comparing both hybrid and conventional HVOF-sprayed coatings, there was an improvement in wear performance by a factor of 4 when using the hybrid material. The results show a significant antiwear improvement provided by the hybrid material. Scanning electron microscopy (SEM) at low/high magnifications showed the distinctive microstructure of the HVOF-sprayed hybrid coating, which helps to explain its excellent wear performance. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

Toughening and strengthening mechanism of plasma sprayed nanostructured Al2O3–13 wt.%TiO2 coatings

The starting materials of Al₂O₃, TiO₂, ZrO₂ and CeO₂ nanoparticles were agglomerated into sprayable feedstock powders and plasma sprayed to form nanostructured coatings. There were net structures and fused structures in plasma sprayed nanostructured Al₂O₃–13 wt.%TiO₂ coatings. The net structures were derived from partially melted feedstock powders and the fused structures were derived from fully melted feedstock powders. The nanostructured Al₂O₃–13 wt.%TiO₂ coatings possessed higher hardness, bonding strength and crack growth resistance than conventional Metco 130 coatings which were mainly composed of lamellar fused structures. The higher toughness and strength of nanostructured Al₂O₃–13 wt.%TiO₂ coatings were mainly related to the obtained net structures.     

Fabrication and Properties of Plasma-Sprayed Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/ZrO<Subscript>2</Subscript> Composite Coatings

Al₂O₃ /xZrO₂ (where x = 0, 3, 13, and 20 wt.%) composite coatings were deposited onto mild steel substrates by atmospheric plasma spraying of mixed α-Al₂O₃ and nano-sized monoclinic-ZrO₂ powders. Microstructural investigation showed that the coatings comprised well-separated Al₂O₃ and ZrO₂ lamellae, pores, and partially molten particles. The coating comprised mainly of metastable γ-Al₂O₃ and tetragonal-ZrO₂ with trace of original α-Al₂O₃ and monoclinic-ZrO₂ phases. The effect of ZrO₂ addition on the properties of coatings were investigated in terms of microhardness, fracture toughness, and wear behavior. It was found that ZrO₂ improved the fracture toughness, reduced friction coefficient, and wear rate of the coatings.     

HVOF thermal spray deposited Y<Subscript>2</Subscript>O<Subscript>3</Subscript>-stabilized ZrO<Subscript>2</Subscript> coatings for thermal barrier applications

High velocity oxy-fuel (HVOF) thermal spray has been successfully used to deposit yttria-stabilized zirconia (YSZ) for thermal barrier coating (TBC) applications. Adherent coatings were obtained within a limited range of spray conditions using hydrogen as fuel gas. Spray parameters such as hydrogen-to-oxygen ratio, spray distance, and substrate cooling were investigated. Spray distance was found to have a pronounced effect on coating quality; adherent coatings were obtained for spray distances between 75 and 125 mm from the gun exit for the hydrogen-to-oxygen ratios explored. Compared to air plasma spray (APS) deposited YSZ coatings, the HVOF deposited coatings were more fully stabilized in the tetragonal phase, and of similar density, surface roughness, and cross-sectional microhardness. Notably, fracture surfaces of the HVOF coatings revealed a more homogeneous structure. Many theoretical models predict that it should not be possible to melt YSZ in an HVOF flame, and therefore it should not be possible to deposit viable YSZ coatings by this process. The experimental results in the present work clearly contradict those expectations. The present results can be explained by taking into account the effect of partial melting and sintering on particle cohesion, as follows. Combustion chamber pressures (P _o) of ∼3.9 bar (58.8 psi) realized during HVOF gun operation allows adiabatic flame temperature values that are above the zirconia melting temperature. Under these conditions, the Ranz-Marshall heat transfer model predicts HVOF sprayed particle surface temperatures T _p that are high enough for partial melting of small (∼10 μm) zirconia particles, T _p=(1.10−0.95)T _m. Further analysis shows that for larger particles (38 μm), adherent coatings are produced when the particle temperature, T _p=0.59−0.60 T _m, suggesting that sintering may have a role in zirconia particle deposition during HVOF spray. These results suggest two different bonding mechanisms for powders having a broad particle size distribution.     

Development and Application of Binary Suspensions in the Ternary System Cr<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for S-HVOF Spraying

Compositions in the system Cr₂O₃-TiO₂-Al₂O₃ are among the most used ceramic materials for thermally sprayed coating solutions. Cr₂O₃ coatings present good sliding wear resistance; Al₂O₃ coatings show excellent insulation behavior and TiO₂ striking corrosion properties. In order to combine these properties, coatings containing more than one oxide are highly interesting. The conventional spraying process is limited to the availability of binary feedstock powders with defined compositions. The use of suspensions offers the opportunity for tailor-made chemical compositions: within the triangle of Cr₂O₃-TiO₂-Al₂O₃, each mixture of oxides can be created. Criteria for the selection of raw materials as well as the relevant aspects for the development of binary suspensions in the Cr₂O₃-TiO₂-Al₂O₃ system to be used as feedstock for thermal spraying are presented. This formulation of binary suspensions required the development of water-based single-oxide suspensions with suitable behavior; otherwise, the interaction between the particles while mixing could lead up to a formation of agglomerates, which affect both the stability of the spray process and the coating properties. For the validation of this formulation procedure, binary Cr₂O₃-TiO₂ and Al₂O₃-TiO₂ suspensions were developed and sprayed using the S-HVOF process. The binary coatings were characterized and discussed in terms of microstructure and microhardness.     

Effect of a surface treatment for LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> cathode material in lithium secondary batteries

LiNi_1/3Co_1/3Mn_1/3O₂ cathode material was surface-treated to improve its electrochemical performance. Al₂O₃ nanoparticles were coated onto the surface of LiNi_1/3Co_1/3Mn_1/3O₂ powder using a sol-gel method. The as-prepared Al₂O₃ nano-particle was identified as the cubic structure of Al₂O₃. XRD showed that the LiNi_1/3Co_1/3Mn_1/3O₂ structure was not affected by the Al₂O₃ coating. With a coating of 3 wt.% Al₂O₃ on LiNi_1/3Co_1/3Mn_1/3O₂, the cyclic-life performance and rate capability were improved. However, heavier coatings (5 wt.%) on LiNi_1/3Co_1/3Mn_1/3O₂ resulted in a considerable decrease of the discharge capacity and rate capability. The thermal stability of LiNi_1/3Co_1/3Mn_1/3O₂ materials was greatly improved by the 3 wt.% Al₂O₃ coating.     

Photoresponse and donor concentration of plasma-sprayed TiO<Subscript>2</Subscript> and TiO<Subscript>2</Subscript>-ZnO electrodes

The photoelectrochemical characteristics of plasma-sprayed porous TiO₂, TiO₂-5%ZnO, and TiO₂-10%ZnO electrodes in 0.1 N NaOH solution were studied through a three-electrode cell system. The microstructure, morphology, and composition of the electrodes were analyzed using an electron probe surface roughness analyzer (ERA-8800FE), scanning electron microscopy, and x-ray diffraction. The results indicate that the sprayed electrodes have a porous microstructure, which is affected by the plasma spray parameters and composition of the powders. The TiO₂-ZnO electrodes consist of anatase TiO₂, rutile TiO₂, and Zn₂Ti₃O₈ phase. The photoresponse characteristics of the plasma-sprayed electrodes are comparable to those of single-crystal TiO₂, but the breakdown voltage is close to 0.5 V (versus that of a saturated calomel electrode). The short-circuit photocurrent density (J _SC) increases with a decrease of donor concentration, which was calculated according to the Gartner-Butler model. For the lowest donor concentration of a TiO₂-5%ZnO electrode sprayed under an arc current of 600 A, the short-circuit J _SC is approximately 0.4 mA/cm² higher than that of the TiO₂ electrodes under 30 mW/cm² xenon light irradiation. The J _SC increases linearly with light intensity. The original version of this paper was published as part of the DVS Proceedings: “Thermal Spray Solutions: Advances in Technology and Application,” International Thermal Spray Conference, Osaka, Japan, 10–12 May 2004, CD-Rom, DVS-Verlag GmbH, Düsseldorf, Germany.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> particles on the microstructure and sliding wear of 7075 Al alloy manufactured by squeeze casting method

Aluminum (Al) alloy 7075 reinforced with Al₂O₃ particles was prepared using the stir casting method. The microstructure of the cast composites showed some degree of porosity and sites of Al₂O₃ particle clustering, especially at high-volume fractions of Al₂O₃ particles. Different squeeze pressures (25 and 50 MPa) were applied to the cast composite during solidification to reduce porosity and particle clusters. Microstructure examinations of the squeeze cast composites showed remarkable grain refining compared with that of the matrix alloy. As the volume fraction of particles and applied squeeze pressure increased, the hardness linearly increased. This increase was related to the modified structure and the decrease in the porosity. The effect of particle volume fraction and squeeze pressure on the dry-sliding wear of the composites was studied. Experiments were performed at 10, 30, and 50 N with a sliding speed of 1 m/s using a pin-on-ring apparatus. Increasing the particle volume fraction and squeeze pressure improved the wear resistance of the composite compared with that of the monolithic alloy, because the Al₂O₃ particles acted as load-bearing constituents. Also, these results can be attributed to the fact that the application of squeeze pressure during solidification led to a reduction in the porosity, and an increase in the solidification rate, leading to a finer structure. Moreover, the application of squeeze pressure improved the interface strength between the matrix and Al₂O₃ particles by elimination of the porosity at the interface, thereby providing better mechanical locking.     

Elevated Temperature Solid Particle Erosion Performance of Plasma-Sprayed Co-based Composite Coatings with Additions of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and CeO<Subscript>2</Subscript>

In this paper, investigation into solid particle erosion behavior of atmospheric plasma-sprayed composite coating of CoCrAlY reinforced with Al₂O₃ and CeO₂ oxides on Superni 76 at elevated temperature of 600 °C is presented. Alumina particles are used as erodent at two impact angles of 30° and 90°. The microstructure, porosity, hardness, toughness and adhesion properties of the as-sprayed coatings are studied. The effects of temperature and phase transformation in the coatings during erosion process are analyzed using XRD and EDS techniques. Optical profilometer is used for accurate elucidation of erosion volume loss. CoCrAlY/CeO₂ coating showed better erosion resistance with a volume loss of about 50% of what was observed in case of CoCrAlY/Al₂O₃/YSZ coating. Lower erosion loss is observed at 90° as compared to 30° impact angle. The erosion mechanism evaluated using SEM micrograph revealed that the coatings experienced ductile fracture exhibiting severe deformation with unusual oxide cracks. Reinforced metal oxides provide shielding effect for erodent impact, enabling better erosion resistance. The oxidation of the coating due to high-temperature exposure reforms erosion process into oxidation-modified erosion process.     

Structure and electric property comparison between Ge nanoclusters embedded in Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/ZrO<Subscript>2</Subscript>

Metal-insulator-semiconductor (MIS) structures containing Ge nanocrystals embedded in both Al₂O₃ and ZrO₂/Al₂O₃ are fabricated by an ultra-high vacuum electron-beam evaporation method. Secondary ion mass spectroscopy (SIMS) results indicate that Ge embedded in Al₂O₃ diffuses towards the surface of the Al₂O₃ layer after annealing at 800°C in N₂ ambient for 30 min. Ge embedded in ZrO₂/Al₂O₃ is stable, thus inducing less leakage current. Capacitance voltage studies indicate that annealing can effectively passivate the negatively charged trapping centers. Memory effect of the Ge nanoclusters is verified by hysteresis in the C-V curves in the Al₂O₃/Ge+Al₂O₃/Al₂O₃ and ZrO₂/Ge+Al₂O₃/Al₂O₃ samples. This article is based on a presentation in “The 7th Korea-China Workshop On Advanced Materials” organized by the Korea-China Advanced Materials Cooperation Center and the China-Korea Advanced Materials Cooperation Center, held at Ramada Plaza Jeju Hotel, Jeju Island, Korea on August 24–27, 2003.     

Preparation and characterization of nanostructured Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-13wt.%TiO<Subscript>2</Subscript> ceramic coatings by plasma spraying

Nanostructured and conventional Al₂O₃-13wt.%TiO₂ ceramic coatings were prepared by plasma spraying with nanostructured agglomerated and conventional powders, respectively. The microstructure and microhardness of the coatings were investigated using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and microhardness measurement. Meanwhile, the friction and wear behaviors were analyzed and compared using a ball-on-disk tribometer. The results show that the conventional coating has lamellar stacking characteristic and has some pores. However, the nanostructured coating shows a bimodal microstructure, which is composed of both fully melted regions and partially melted regions. According to the microstructural difference, the partially melted regions can be divided into liquid-phase sintered regions (a three-dimensional net or skeleton-like structure: Al₂O₃-rich submicron particles embedded in the TiO₂-rich matrix) and solid-phase sintered regions (remained nanoparticles). The microstructural characteristics of the liquid-phase sintered region are formed due to the selective melting of TiO₂ nanoparticles during plasma spraying. On the other hand, the TiO₂ and Al₂O₃ nanoparticles of the solid-phase sintered regions are all unmelted during plasma spraying. Due to the existence of nanostructured microstructures, the nanostructured coating has a higher microhardness, a lower friction coefficient, and a better wear resistance than the conventional coating.     

热喷涂TiB2-Ni复合涂层组织结构和力学性能

采用团聚烧结方法制备TiB₂-Ni复合粉末喂料,并采用大气等离子喷涂和高速火焰喷涂两种喷涂方法制备了TiB₂-Ni涂层,比较分析了两种涂层的显微组织、物相组成、孔隙率、硬度和断裂韧性.结果表明,与等离子喷涂相比,高速火焰喷涂制备的TiB₂-Ni涂层具有更高的致密度,TiB₂含量,硬度和断裂韧性.两种涂层中TiB₂都没有发生明显的脱硼,氧化,但等离子喷涂过程中TiB₂向金属相中发生了溶解生成了大量脆性Ni₂₀Ti₃B₆相,并降低了涂层中TiB₂的含量,这是涂层硬度和断裂韧性相对较低的主要原因.     

Studies on Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/ZrO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> high K gate dielectrics applied in a fully depleted SOI MOSFET

Al₂O₃/ZrO₂/Al₂O₃ gate stacks were prepared on ultrathin SOI (Silicon on insulator) substrates by ultrahigh vacuum electron beam evaporation and post-annealed in N₂ at 450°C for 30 min. Three clear nanolaminate layered structure of Al₂O₃(2.1 nm)/ZrO₂(3.5 nm)/Al₂O₃(2.3 nm) was observed with a high-resolution cross-sectional transmission electron microscope (HR-XTEM). High frequency capacitance voltage (C-V) characteristics of a fully depleted (FD) SOI MOS capacitor at 1 and 5 MHz were studied. The minority carriers determine the high frequency C-V properties, which is opposite to the case of bulk MOS capacitors. The series resistance of the SOI substrate is found to be the determinant factor of the high frequency characteristics of FD SOI MOS capacitors. This article is based on a presentation in “The 7th Korea-China Workshop on Advanced Materials” organized by the Korea-China Advanced Materials Cooperation Center and the China-Korea Advanced Materials Cooperation Center, held at Ramada Plaza Jeju Hotel, Jeju Island, Korea on August 24≈27, 2003.     

Superior performance of high-velocity oxyfuel-sprayed nanostructured TiO<Subscript>2</Subscript> in comparison to air plasma-sprayed conventional Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-13TiO<Subscript>2</Subscript>

Air plasma-sprayed conventional alumina-titania (Al₂O₃-13wt.%TiO₂) coatings have been used for many years in the thermal spray industry for antiwear applications, mainly in the paper, printing, and textile industries. This work proposes an alternative to the traditional air plasma spraying of conventional aluminatitania by high-velocity oxyfuel (HVOF) spraying of nanostructured titania (TiO₂). The microstructure, porosity, hardness (HV 300 g), crack propagation resistance, abrasion behavior (ASTM G65), and wear scar characteristics of these two types of coatings were analyzed and compared. The HVOF-sprayed nanostructured titania coating is nearly pore-free and exhibits higher wear resistance when compared with the air plasma-sprayed conventional alumina-titania coating. The nanozones in the nanostructured coating act as crack arresters, enhancing its toughness. By comparing the wear scar of both coatings (via SEM, stereoscope microscopy, and roughness measurements), it is observed that the wear scar of the HVOF-sprayed nanostructured titania is very smooth, indicating plastic deformation characteristics, whereas the wear scar of the air plasma-sprayed alumina-titania coating is very rough and fractured. This is considered to be an indication of a superior machinability of the nanostructured coating.     

Microstructural characterization of plasma sprayed Al2O3-40 wt.% TiO2 coatings on high density graphite with different post-treatments

Graphite is one of the candidate materials proposed for application in pyrochemical reprocessing plants involving aggressive molten chloride environment. Post treatments are promising techniques for the improvement of properties of thermal spray coatings for different industrial applications. In the present work, the effect of post treatments like vacuum annealing (VA) and laser melting (LM) on the microstructure and chemical modification of plasma sprayed Al₂O₃-40 wt.% TiO₂ coatings over high density (HD) graphite substrates has been investigated. When compared with sprayed coatings (SC), VA coatings showed cluster morphology and LM coatings exhibited homogenous microstructure. On laser melted surfaces networks of cracks were observed. XRD studies showed that the metastable γ-Al₂O₃ phase present in the SC is transformed to stable α-Al₂O₃ after post treatments. In LM coatings Al₂TiO₅ phase was more predominant in contrast to SC and VA coatings. The microhardness enhancement was observed in case of LM coating compared to the VA and SC. Due to elimination of coating defects in LM samples, there is a considerable reduction in the surface roughness.     

Influence of FeCrAl Content on Microstructure and Bonding Strength of Plasma-Sprayed FeCrAl/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Coatings

Low-power plasma-sprayed FeCrAl/Al₂O₃ composite coatings with 1.5 mm thickness have been fabricated for radar absorption applications. The effects of FeCrAl content on the coating properties were studied. The FeCrAl presents in the form of a few thin lamellae and numerous particles, demonstrating relatively even distribution in all the coatings. Results show that the micro-hardness and porosity decrease with the increase in FeCrAl content. With FeCrAl content increasing from 28 to 47 wt.%, the bonding strength of the coatings with 1.5 mm thickness increases from 10.5 to 27 MPa, and the failure modes are composed of cohesive and adhesive failure, which are ascribed to the coating microstructure and the residual stress, respectively.     

Cr<Subscript>3</Subscript>C<Subscript>2</Subscript>-NiCr HVOF-Sprayed Coatings: Microstructure and Properties Versus Powder Characteristics and Process Parameters

Two 75%Cr₃C₂-25%NiCr feedstock powders with the same size distribution but different production process were characterized and found quite different in terms of morphology and phase composition. The powders were sprayed in a HVOF Diamond Jet (Sulzer Metco DJ-2600) torch with five different values of the oxygen-to-hydrogen ratio in order to assess the influence of this parameter on the microstructure and properties of the coatings. The results show that the closed and dense microstructure of one powder (Woka 7302) results in coatings with lower amount of decarburization, less oxide formation and higher toughness compared to coatings from the other powder (Praxair 1375). It was found that the O₂/H₂ ratio impacts mainly on the Young’s modulus, which almost doubled by changing the ratio from 0.40 to 0.50, and on toughness, but does not notably affect the Vickers hardness.     

Mechanical Properties of LaTi<Subscript>2</Subscript>Al<Subscript>9</Subscript>O<Subscript>19</Subscript> and Thermal Cycling Behaviors of Plasma-Sprayed LaTi<Subscript>2</Subscript>Al<Subscript>9</Subscript>O<Subscript>19</Subscript>/YSZ Thermal Barrier Coatings

Recently, extensive efforts have been made to develop new thermal barrier coating (TBC) materials which can operate at temperatures above 1523 K over a long term. In this article, LaTi₂Al₉O₁₉ (LTA) was synthesized by solid-state reaction at 1773 K, and the mechanical properties of the LTA bulk were evaluated. The microhardness is about 14 GPa, comparable to that of YSZ bulk, whereas the Young’s modulus is about 44 GPa, lower than the value of YSZ. However, the fracture toughness of 0.8-1 MPa m^1/2 is much lower than that of bulk YSZ. A double-ceramic-layer LTA/YSZ TBC structure was proposed and the TBC sprayed by plasma spraying. Thermal cycling tests of the TBC specimens were performed at 1373 K with a dwell time of 10 min. The LTA remained good stability with ZrO₂ and Al₂O₃. However, the single layer LTA TBC was cracked at the LTA/bond coat interface after about 300 cycles, due to its poor thermal shock resistance, while the YSZ TBC yielded a lifetime of about 1000 cycles. The LTA/YSZ TBC remained intact even after 3000 cycles, exhibiting a promising potential as new TBC materials.     

Mechanical Properties of Layered La<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript> Thermal Barrier Coatings

Lanthanum zirconate (La₂Zr₂O₇) has been proposed as a promising thermal barrier coating (TBC) material due to its low thermal conductivity and high stability at high temperatures. In this work, both single and double-ceramic-layer (DCL) TBC systems of La₂Zr₂O₇ and 8 wt.% yttria-stabilized zirconia (8YSZ) were prepared using air plasma spray (APS) technique. The thermomechanical properties and microstructure were investigated. Thermal gradient mechanical fatigue (TGMF) tests were applied to investigate the thermal cycling performance. The results showed that DCL La₂Zr₂O₇ + 8YSZ TBC samples lasted fewer cycles compared with single-layered 8YSZ TBC samples in TGMF tests. This is because DCL La₂Zr₂O₇ TBC samples had higher residual stress during the thermal cycling process, and their fracture toughness was lower than that of 8YSZ. Bond strength test results showed that 8YSZ TBC samples had higher bond strength compared with La₂Zr₂O₇. The erosion rate of La₂Zr₂O₇ TBC samples was higher than that of 8YSZ samples, due to the lower critical erodent velocity and fracture toughness of La₂Zr₂O₇. DCL porous 8YSZ + La₂Zr₂O₇ had a lower erosion rate than other SCL and DCL La₂Zr₂O₇ coatings, suggesting that porous 8YSZ serves as a stress-relief buffer layer.