大型快速流化床内颗粒浓度和速度分布的实验研究

采用压力巡检仪和光纤测量仪,对直径300 mm的快速流化床反应器内气固两相流动特性进行了研究,考察了操作条件对快速床轴、径向催化剂颗粒浓度、颗粒速度、筛分分布等的影响. 结果表明,当操作气速提高到2.0~2.6 m/s,相应的催化剂循环强度在60~160 kg/(m2×s),床层密度可保持在50~650 kg/m3;催化剂颗粒浓度在径向上呈中心低、边壁高的不均匀分布,轴向上各径向位置在颗粒加速区逐渐降低、在充分发展区趋于稳定、随表观气速增大或催化剂循环强度减小而减小,且径向均匀性变好,在r/R<0.7的中心区域趋于一致;颗粒速度在径向上呈中心高、边壁低的抛物线形分布,且随操作气速增大或催化剂循环强度增大而更加明显.     

内置钝体对快速流化床中颗粒浓度分布的影响

本文在内径140mm的快速流化床中,考察了内置钝体对床内轴向压力分布和径向颗粒浓度分布的影响。实验结果表明,内置钝体构件对于快速流化床中的压力和浓度的分布影响显著,而且大大增强了气固两相的径向混合。     

气固下行流化床反应器Ⅱ气固两相的流动规律

气固下行流化床反应器气固两相流动过程是比较复杂的，沿轴向气固两相运动可分为第一加速、第二加速和恒速３个运动段，沿径向局部气体速度、颗粒速度和颗粒浓度都具有不同程度的不均匀性。而这种不均匀性是由气固两相顺重力场湍动运动所决定的。和循环床提升管相比，下行管反应器气固两相沿径向分布的不均匀性得到有效地改善，气固可以实现超短接触操作，因而是一种新型高效气固超短接触反应器     

二元颗粒混合物在下行床反应器中局部颗粒速度的分布

采用PV-4A光导纤维测速仪在一高2m、直径30mm的下行床反应器中较系统地测定了FCC催化剂及玻璃珠各自在6个截面8个不同径向位置局部颗粒速度的轴向及径向分布,研究了操作条件及喷口位置对该两种不同物料局部颗粒速度径向分布的影响,进而将FCC催化剂和玻璃珠两种物料分别同时进入下行床反应器中,考察了以不同混合比组成的二元组分混合物的颗粒速度径向双峰分布特点.最后,分别给出了预测FCC催化剂及玻璃珠的量纲1局部颗粒速度经验关联式.实验结果表明：物性不同的粒子其局部颗粒速度径向分布差别较大,二元组分混合物的颗粒速度径向分布较FCC催化剂单一颗粒趋于均匀,且随表观气速增加,颗粒速度分布双峰特性愈为明显,可见在下行床进入细颗粒的同时加入粗颗粒引起了气固流动机制的变化与颗粒速度分布的平滑.     

循环流化床多组分颗粒气固两相流动模型和数值模拟

基于稠密气体分子运动论和颗粒动力学,考虑多组分颗粒中颗粒组分与颗粒组分、颗粒组分内颗粒之间的相互作用以及气体与颗粒之间的相互作用,提出多组分颗粒非等温颗粒气固两相流动模型.以颗粒压力、径向分布函数、黏度、颗粒碰撞耗散等耦合各颗粒组分间和颗粒间的相间作用.采用大涡模拟方法模拟气相湍流流动.提出了多组分颗粒的径向分布函数计算方法.对循环流化床上升管中双组分颗粒气固两相流动特性进行了数值模拟,模拟结果揭示了上升管中双组分颗粒气固两相流动的环-核流动结构,得到了平均颗粒粒径的轴向和径向分布规律,计算结果与文献中实验结果相吻合.     

液固提升管-流化床组合反应器中流化床径向固含率分布的实验研究

在一套新型液固提升管-流化床组合反应器中，以水-玻璃珠为液-固体系，对f500 mm′4000 mm的液固流化床反应器内不同高度颗粒固含率的径向分布进行了实验，考察了表观液速和颗粒循环速率操作条件对颗粒固含率径向分布的影响. 实验表明，液固流化床内流动区域在轴向上可以划分为分布器影响区、过渡区和均匀流化区，径向上可以划分为中心区和环隙区. 这种分布特征主要取决于分布器的结构、尺寸及其流化介质. 本工作还对液固流化床与气固喷动床的三区流动结构进行了比较.     

快速流化床内颗粒加速运动段长度

本文根据对快速流化床内气固两相流动的分析,确定压力沿床高分布的非线性变化区域为颗粒的加速运动段。通过对大量实验数据的分析,得到了颗粒加速段长度及其随操作条件,气固物性以及床层直径等因素的变化规律。结果充分表明,在快速流态化区域内,颗粒的加速作用是非常明显的。     

ＣＦＢ稀相段直长对颗粒内循环流动规律的影响

采用光纤探头测定Ｄ１m射流循环流化床（半圆形）稀相区颗粒速度、颗粒浓度和颗粒流通量的径向分布规律,并考察了操作条件及其轴向的影响,实验结果表明,在循环流化床（ＣＦＢ）中,颗粒流动在床层径向有较大的不均匀性,并呈明显的内循环流动结构,进而考察了影响其流动规律的,以期进一步理解循环流化床颗料流动机理,强化和改善反应器的设计操作。     

不同流型下组合约束型提升管出口段固含率分布

在一套组合约束型提升管冷态实验装置上,研究了气力输送和快速流态化两种流型下,出口段局部固含率分布规律及不同操作条件对固含率的影响。结果表明:局部固含率径向分布整体上呈中心小、边壁大的分布特征,并随分布器开孔率和表观气速的降低而增大,随上部流化床层压降和颗粒循环强度的降低而减小;在快速流态化操作下,局部固含率曲线分布形式与常规提升管类似,而在气力输送状态下,临近出口区域局部固含率最大值通常不出现在边壁处,其位置随表观气速和分布器开孔率增加以及颗粒循环强度和上部流化床层压降降低而远离边壁;两种流型下局部固含率径向分布的均匀性均随表观气速及分布器开孔率的增加而升高,随颗粒循环强度及流化床层压降的增加而降低。     

提升管-下行床耦合反应器内颗粒混合行为

引　言循环流化床中气固两相的流动有两种不同的方式 :提升管中为气固并流上行的逆重力场运动 ,下行床中为气固并流下行的顺重力场运动 .其差异表现为提升管内颗粒浓度、速度以及气体速度在径向上严重的不均匀 ,颗粒浓度概率密度分布以及速度的瞬时信号都表明了颗粒团 -空穴两相结构的存在[1] ,一些研究[2 ,3] 还发现提升管中颗粒的停留时间分布 (ＲＴＤ)曲线存在较大的拖尾甚至出现双峰 ,研究者认为提升管内存在弥散颗粒和颗粒团两种不同的混合机理 ;下行床则比提升管大大改善 ,气固速度、颗粒浓度沿径向分布要均匀得多 ,颗粒的ＲＴＤ曲线…     

GAS-SOLIDS FLOW PATTERNS IN A CONCURRENT DOWNFLOW FAST FLUIDIZED BED(CDFFB)

Radial profiles of solid concentration and velocity for concurrent downward gas-solid suspension in a140mm inside diameter fast fluidized bed were investigated.The influence of gas velocity,solid circulating rateand axial position on radial profiles of solid concentration and particle velocity has been examined.It hasbeen found that an annular region of high solid concentration exists at r/R=0.94.At both the center and wallregion,the solid concentration and the particle velocities are relatively low.The shape of radial solid con-centration profile curves is mainly dependent on the cross-section averaged voidage,and the shape of radialparticle velocity profile is mainly affected by the gas velocity and cross-section averaged voidage.Based on the radial profiles of solid concentration and particle velocity,the solid mass flux profile and thenonuniformity of solids flow are discussed in this paper.It is shown that solids flow in CDFFB is much moreuniform than that in UFFB.     

EFFECTS OF PARTICLE CHARACTERISTICS ON THE PERFORMANCE OF A FAST FLUIDIZED BED REACTOR

A heterogeneous model for the fast fluidized bed reactor which carries out a gas-solid non catalytic reaction is presented. The hydrodynamics of the fast fluidized bed is characterized by the model of Kwauk et al. (1985) which assumes the existence of two phases; a dense phase and a dilute pneumatic transport phase. For a given solid flowrate, the length of the reactor occupied by each phase depends on gas velocity, particle diameter and density and average voidage within the reactor. The gas-solid reaction is assumed to follow the shrinking core model. The solids are assumed to be completely backmixed in the dense phase and move in plug How in the dilute pneumatic transport phase. The gas phase is assumed to be in plug flow in both phases

For given gas and solid flowrates, the transition from the dense phase flow to the fast fluidized bed (containing two regions) as functions of particle size and density is determined using the model of Kwauk et al. (1985). The numerical solution of the governing mass balance equations show that for given solid and gas flowrates, (and average voidage) the gas phase conversion shows an unusual behavior with respect to particle diameter and density. Such behavior is resulted from the effects of particle diameter and density on the reactor volume occupied by each phase and the effect of particle diameter on the apparent reaction rate. The numerical results show that a fast fluidized bed gives the best conversion at large particle density and for the particle diameter which results the fast fluidized bed to be operated near the pure dense phase flow.     

快速流化床中平均滑落速度及絮状物的特性

本文依据大量实验数据,研究快速流化床的操作条件,气固物性等参数对于床内颗粒平均滑落速度的影响。颗粒聚集为絮状物是快速流化床中气固流动的一个重要特征,文中对等效絮状物的基本特征进行了讨论,根据大量实验数据对絮状物的终端速度、絮状物当量直径,以及絮状物中的粒子个数作了推算,这对认识快速流化床气固接触机理及反应器的设计具有参考价值。     

低密度循环流化床局部颗粒速度的轴径向分布的研究

在高8m,内径186mm的循环流化床中,利用光纤激光多普勒测速仪测量了FCC颗粒的局部速度沿轴径向的分布。实验结果表明:局部颗粒速度沿径向分布是不均匀的,床中心区域分布比较平坦,近壁环形区域分布较陡,颗粒沿轴向运动有较长的加速段。由实验数据回归得到预测低密度循环流化床局部颗粒速度的经验关联式。     

多段分级转化流化床提升管速度场的研究

针对流化床煤气化过程中需要长气固接触时间和高固体浓度,开发了耦合灰熔聚流化床和提升管的多段分级转化流化床。为了研究多段分级转化流化床提升管中局部颗粒速度的径向、轴向分布,在不同的操作条件下,采用PV-6型颗粒速度测量仪在冷态实验装置中系统测定提升管内局部颗粒速度。实验结果表明:提升管中任何径向、轴向位置的颗粒速度随着操作气速的增大而增大,随循环量的增加而减小。操作条件对中心区颗粒速度变化的影响明显高于边壁区。颗粒的加速首先发生在提升管中心区域,然后向边壁区域扩展。颗粒速度径向分布的不均匀性沿轴向逐渐增大,并且受操作气速影响比较大。     

气-固并流下行快速流态化的研究(I)

研究气-固并流顺重力场运动中气-固两相之间的相互作用,并依此将气-固运动过程分为第Ⅰ、Ⅱ加速段及恒速段.在直径为φ140mm,高为5.8m的下行快床中,测定了不同操作条件下(μ_g=1.3-10m/s,G_a=30-180kg/m~2·s)床层压力梯度轴向分布及第Ⅰ加速段长度的变化规律,同时考察了颗粒特性对上述过程的影响.     

网格尺寸对循环流化床内气固两相流动的影响

将基于能量最小多尺度方法(EMMS)的曳力模型耦合到双流体模型中,并针对循环流化床内的气固两流动进行了模拟研究。采用全滑移壁面边界条件处理颗粒相,考察了3种网格尺度对轴向空隙率和出口颗粒循环量等气固流动特性的影响。计算结果表明,应用EMMS曳力模型处理相间作用力,同时在采用全滑移壁面边界条件处理颗粒相时,双流体模型能够正确预测轴向空隙率分布。采用网格尺寸为2.325 mm×20 mm时,模拟结果和实测数据吻合较好,表明在循环流化床的数值模拟中选择恰当的网格尺度是极为重要的。     

提升管-流化床耦合反应器颗粒约束返混区的流动特性及约束作用分析

针对催化汽油辅助反应器改质降烯烃工艺,在一套提升管-流化床耦合反应器大型冷态实验装置上,系统研究了提升管出口段的颗粒流动特性,通过定义约束指数R_i（R_i为颗粒约束返混区实际截面平均固含率与理论截面平均固含率之比）定量反映提升管出口分布器及流化床层的约束作用。结果表明,与常规提升管相比,耦合反应器提升管出口存在一个颗粒约束返混区,其长度主要受表观气速、颗粒循环强度及上部流化床内颗粒静床高度影响;由于出口设置了倒锥形分布器,使得颗粒约束返混区靠近提升管出口区域在表观气速较低和颗粒循环强度较大时,局部固含率最大值出现在量纲 1半径Φ＝0.7处;颗粒约束返混区的约束指数在靠近出口的过程中逐渐增大,气固流动受到分布器及上部流化床层的约束作用亦逐渐增强。     

Solid concentration and velocity distributions in an annulus turbulent fluidized bed

Solid concentration and particle velocity distributions in the transition section of a?200 mm turbulent fluidized bed (TFB) and a?200 mm annulus turbulent fluidized bed (A-TFB) with a?50 mm central standpipe were mea-sured using a PV6D optical probe. It is concluded that in turbulent regime, the axial distribution of solid concen-tration in A-TFB was similar to that in TFB, but the former had a shorter transition section. The axial solid concentration distribution, probability density, and power spectral distributions revealed that the standpipe hin-dered the turbulence of gas–solid two-phase flow at a low superficial gas velocity. Consequently, the bottom flow of A-TFB approached the bubbling fluidization pattern. By contrast, the standpipe facilitated the turbulence at a high superficial gas velocity, thus making the bottom flow of A-TFB approach the fast fluidization pattern. Both the particle velocity and solid concentration distribution presented a unimodal distribution in A-TFB and TFB. However, the standpipe at a high gas velocity and in the transition or dilute phase section significantly affected the radial distribution of flow parameters, presenting a bimodal distribution with particle concentration higher near the internal and external wal s and in downward flow. Conversely, particle concentration in the middle an-nulus area was lower, and particles flowed upward. This result indicated that the standpipe destroyed the core-annular structure of TFB in the transition and dilute phase sections at a high gas velocity and also improved the particle distribution of TFB. In conclusion, the standpipe improved the fluidization quality and flow homogeneity at high gas velocity and in the transition or dilute phase section, but caused opposite phenomena at low gas ve-locity and in the dense-phase section.     

Computational fluid dynamics of a circulating fluidized bed under various fluidization conditions

A computational fluid dynamics (CFD) model was developed to simulate the hydrodynamics of gas-solid flow in a circulating fluidized bed (CFB) riser at various fluidization conditions using the Eulerian-Granular multiphase model. The model was evaluated comprehensively by comparing its predictions with experimental results reported for a CFB riser operating at various solid mass fluxes and superficial gas velocities. The model was capable of predicting the main features of the complex gas-solids flow, including the cluster formation of the solid phase along the walls, for different operating conditions. The model also predicted the coexistence of up-flow in the lower regions and downward flow in the upper regions at the wall of the riser for high gas velocity and solid mass flux, as reported in the literature. The predicted solid volume fraction and axial particle velocity were in good agreement with the experimental data within the high density fast fluidization regime. However, the model showed some discrepancy in predicting the gas-solid flow behavior in the riser operating in dense suspension up-flow and low density fast fluidization regimes.