介质加载矩形谐振腔分析

利用导波系统中传输模的横向谐振法,导出了介质加载矩形谐振腔中分层介质区内谐振模的本征值方程,由此可精确地求解其谐振频率。     

二氧化硅衬底中太赫兹超介质谐振特性的研究

设计了一种工作在0.3~1.1 THz的双开口太赫兹超介质,最小透射系数为0.06,传输幅度在0.5以下的带宽为0.11 THz。利用等效电路法对这种超介质单元的谐振特性进行了理论分析,用HFSS对超介质单元进行仿真分析。结果表明,超介质单元的结构参数对其谐振特性的影响与理论分析是一致的。通过对超介质结构参数分析可知,若要调节超介质单元的谐振特性,调节其外环开口缝隙宽度是最有效、最直接的方法。     

介质谐振腔任意模式谐振频率的求解

本文用模式匹配法计算圆柱形对称和非对称介质谐振腔内任意谐振模式的谐振频率。文章对有关公式做了详细的推导和必要的简化,计算结果与实验和有关资料都很一致。     

单负介质部分填充圆柱谐振腔的亚波长谐振特性分析

探讨了单负介质部分填充的圆柱谐振腔的基本特性,得到磁负介质或者电负介质部分填充的圆柱谐振腔中存在谐振频率与谐振腔尺寸无关的谐振模式,即存在亚波长谐振模式,并对之特性进行分析研究,得到了一些与普通谐振腔不同的奇特谐振特性。单负介质是容易获得的,从而可以实现亚波长谐振器以实现微波器件的小型化。     

可调介质谐振天线的研究进展

可调介质谐振天线是无线通信领域的研究热点,本文对近年来可调介质谐振天线的研究热点和研究现状进行了介绍,并对可调介质谐振天线已有的研究方法进行了总结和分析,概述了加载寄生导电片、加载寄生槽(缝隙)、采用液体介质、增加空气带隙、使用特殊介质材料、使用开关(转换)器件这几种可调技术,最后分析了各种可调技术的优缺点。     

复合缝波导耦合器的全波分析

本文使用时域有限差分法 (FDTD法 )对由两根正交矩形波导构成的复合缝耦合器进行了严格分析 ,得出在不同偏置、倾斜角度和谐振频率下耦合缝隙的谐振长度和散射参量特性 ;并对带有短路器的复合缝波导耦合器系统进行了分析 ,得出短路片移动时该小系统的传输特性     

介质谐振天线的发展

介绍了介质谐振器及其特点，并详细地分析了当前已有的各种介质谐振天线和新型介质谐振天线。     

单层带通FSS结构中空气间隙的影响

以狭缝阵列为例,利用模匹配法计算分析,并结合实验,针对即贴型频率选择表面(FSS)与介质板复合结构中的空气间隙进行研究.结果表明,空气间隙对FSS结构的传输特性影响与介质厚度和空气间隙大小密切相关.合空气间隙时谐振频率比无空气间隙时向高处漂移.空气间隙的厚度达到一定值后,传输特性随空气间隙厚度周期性变化.在同一周期中,传输特性的变化幅度取决于介质厚度.基于研究结果提出了隐身屏蔽罩概念,为大入射角下低损耗FSS天线罩的应用提供了新思路.     

小型TM010模介质谐振器滤波器

求解圆形介质杆谐振器的特征方程,得到了谐振模式图。TM_(010)模介质谐振器谐振频率的计算值与测量值相符。对介质杆谐振器的Q值进行了讨论。给出了S波段小型TM_(010)模介质谐振器滤波器的实验结果。     

高速嵌入式系统中电源噪声抑制方法

根据平面腔体谐振模型理论推导出高速嵌入式电路电源平面对阻抗函数关系式,分 析了电源平面对的谐振特性与PCB板材、介质层厚度以及导体平面的电导率之间的关系,得 出可通过减小介质层厚度、使用高介电常数的介质材料以及增加介质损耗等3种方法来抑制 电源平面对的谐振效应,并使用全波仿真方法验证了可行性。从时域仿真了高速电路中的噪 声传播与电源平面谐振的相互关系,结果表明,通过抑制电源平面对谐振阻抗可将电源噪声 减 小至原有结构的15%,从而有效提高系统的电源完整性。     

Coplanar Waveguide: A Surface Strip Transmission Line Suitable for Nonreciprocal Gyromagnetic Device Applications

A coplanar waveguide consists of a strip of thin metallic film on the surface of a dielectric slab with two ground electrodes running adjacent and parallel to the strip. This novel transmission line readily lends itself to nonreciprocal magnetic device applications because of the built-in circularly polarized magnetic vector at the air-dielectric boundary between the conductors. Practical applications of the coplanar waveguide have been experimentally demonstrated by measurements on resonant isolators and differential phase shifters fabricated on low-loss dielectric substrates with high dielectric constants. Calculations have been made for the characteristic impedance, phase velocity, and ripper bound of attenuation of a transmission line whose electrodes are all on one side of a dielectric substrate. These calculations are in good agreement with preliminary experimental results. The coplanar configuration of the transmission system not only permits easy shunt connection of external elements in hybrid integrated circuits, but also adapts well to the fabrication of monolithic integrated systems. Low-loss dielectric substrates with high dielectric constants may be employed to reduce the longitudinal dimension of the integrated circuits because the characteristic impedance of the coplanar waveguide is relatively independent of the substrate thickness; this may be of vital importance for Iow-frequency integrated microwave systems.     

PPS基纳米复合介质制备与性能研究

采用化学沉淀法制备了平均粒径约30 nm的TiO2粉料,以聚苯硫醚树脂为基复合纳米无机粉料,结合螺杆挤出与模压等工艺制备了复合介质基板,借助SEM、EDS、DTA-TGA分别对合成的纳米粉料及树脂基复合料进行了微观结构表征与分析,用带状线方法对PPS基无机复合介质基板微波复介电常数进行了测量。获得了相对介电常数为6.0～13.0,且损耗低的高性能新型微波复合介质材料。     

Mutual coupling between metal strip antennas on finite size,electrically thick dielectric substrates

An analysis of the mutual coupling between metal strip antennas which are contiguous with the ends of finite-size, electrically thick dielectric substrates is outlined. Such antennas have been proposed as useful monolithic microwave integrated circuit antennas for millimeter-wavelength applications. The analysis presented was verified experimentally, and the results are applied to three-element arrays of metal strip folded dipoles with coplanar strip feed lines. The effect of the electrically thick, finite-size dielectric substrates on the mutual coupling between elements of the arrays is described     

A Simple Technique for the Accurate Determination of the Microwave Dielectric Constant for Microwave Integrated Circuit Substrates (Correspondence)

A method of determining the microwave dielectric constant of microwave integrated circuit substrates is described. The technique is especially suitable to substrates being prepared for MICs since they are, in general, regular, rectangular, and, therefore, simple resonators. The dielectric constant using this technique has been determined in the 2- to 12-GHz range for GaAs (/spl epsiv/R = 12.46), sapphire (/spl epsiv/R =9.37), polyguide (/spl epsiv/ =2.33), and Alsimag 772 (/spl epsiv/R = 10.08).     

An Accurate Determination of Dielectric Loss Effect in Monolithic Microwave Integrated Circuits Including Microstrip and Coupled Microstrip Lines

For the first time, by a rigorous analysis, the performance of MIC planar transmission lines with Iossy substrates can be studied accurately. The generaf structural shape chosen for the analysis includes infinitely thin metallic strips embedded within the layers of homogeneous dielectric substrates. The rigor of the analysis was guaranteed by the assumption of the propagation of an electromagnetic hybrid wave (i.e., TE+TM) along tbe planar transmission lines. An efficient computation was, however, achieved by implementing the spectral domain approach as the basis for the analysis. To test the analysis, phase constants, characteristic impedances, and attenuations, due to dielectric losses, were computed for microstrip and coupled microstrip lines. The results obtained were compared with those given previously by the spectral domain analysis in which dielectric losses were not included directly [1]. The comparison showed an excellent agreement between the two theories for low-loss substrates. However, for Iossy substrates the present method is more accurate.     

Full wave approach for the analysis of open planar waveguides withfinite width dielectric layers and ground planes

A unified full wave approach based on an extended method of lines is presented for the analysis of open planar waveguides. It can be used to analyze various open planar waveguides and is suitable especially for dielectric substrates with discontinuities and/or with finite ground planes where a full wave approach is not available yet. The convergence of the method is examined by numerical experiments. As application examples, the dispersion characteristics of open single and coupled microstrip lines with finite dielectric substrates are calculated and compared with the full wave results for structures with infinite width dielectric/conductor and the available quasi-static results for single microstrip line with finite dielectric in the literature. The effect of dielectric width on the characteristics is also discussed     

RF, DC, and Reliability Performance of MIM Capacitors Embedded in Organic Substrates by Wafer-Transfer Technology (WTT) for System-on-Package Applications

In this paper, radio frequency (RF), dc, and reliability performance have been studied on metal-insulator-metal (MIM) capacitors embedded in organic substrates. The MIM structure including ~74-nm SiN dielectric was prefabricated on Si and then transferred onto organic substrates (FR-4) by wafer-transfer technology (WTT). The RF characteristics up to 30 GHz were investigated by equivalent lumped circuit modeling, showing that the parameters associated with the MIM layers including the main capacitance, parasitic inductance, and resistance were only slightly changed by the WTT process. The substrate-related parasitics were reduced as a result of the replacement of lossy Si with insulating FR-4 substrates. Excellent capacitance linearity, low voltage coefficient (~2.2 ppm/V²), and temperature coefficient (~38 ppm/degC) were obtained for capacitors on FR-4 substrates. Current-voltage and time-dependent dielectric breakdown tests verified that, after the harsh processes of WTT, the MIM structures maintained the intrinsic reliability as those originally fabricated on Si. This paper, along with earlier reports, proved that WTT presented a new dimension to realize embedded capacitors for high-density circuit board and system-on-package applications     

External field coupling to MTL networks with nonlinear junctions:numerical modeling and experimental validation

The problem of predicting the voltages and currents induced on a printed circuit multiconductor transmission line (MTL) network by an impinging transient plane wave electromagnetic field is considered. The MTL network contains nonlinear circuit elements and test cases with various dielectric substrates are examined. Numerical predictions based on quasi-TEM models of the MTL and modified nodal analysis (MNA) models of the lumped element junctions are compared to experimental results obtained in the time domain using a GTEM cell. As has been done in the past, the effect of the incident plane wave is introduced as forcing functions in the MTL equations. The primary goal of this paper is to quantify the accuracy of the various commonly used quasi-TEM mathematical time-domain models. It is shown that when modeling the forcing function terms, it is important to take into account the perturbation of the incident plane wave due to the dielectric substrate. (The experimental-numerical comparisons herein are shown for the case of end-fire illumination since it best demonstrates this point.) Neglecting the dielectric effect on the incident transient pulse, even for substrates with low dielectric constant, produces poor results     

X-Band Microstrip-Inserted Puck Circulator Using Arc-Plasma-Sprayed Ferrite (Short Papers)

Experimental circulators using ferrite pucks which have been sprayed into cavities in dielectric substrates by an arc-plasma spray (APS) process are described.     

Analysis of the tapered slot antenna

A method for calculating the radiation pattern of end-fire tapered slot antennas with or without dielectric substrate is presented. The method involves a two-step procedure: 1) determine the field distribution of a traveling wave along the tapered slot, and 2) compute the radiation from this slot field by using the half-plane Green's function to account for termination effects. Acceptable estimates of the slot field usually can be obtained from a stepped approximation to the tapered geometry. The method has been verified by comparisons to measured patterns for various dielectric substrates and antenna dimensions. However, the effect of lateral truncation has not yet been successfully modeled. Experimental patterns showing this effect are presented.