乙酸甲酯与甲醇共沸物催化精馏水解工艺

以乙酸甲酯与甲醇共沸物为原料,采用阳离子交换树脂为催化剂,研究了乙酸甲酯催化精馏水解工艺。在实验中以捆扎包作为催化剂的装填方式,系统地研究了催化精馏段和提馏段的高度、进料位置、进料中含甲醇、水酯物质的量比、回流进料比和空速等对酯分解率的影响,获得了最佳的工艺条件。分析了传统的水解分离工艺,提出了可行的新工艺。在最佳工艺条件下,新工艺系统的能耗比传统的固定床工艺降低39.99%。     

Simulation study on a reactive distillation process of methyl acetate hydrolysis intensified by reaction of methanol dehydration

Methyl acetate (MeOAc) recovery from the polyvinyl alcohol (PVA) production is a difficult and heavy energy consuming process. In this work, a reactive distillation (RD) process of MeOAc hydrolysis intensified by methanol (MeOH) dehydration, as an auxiliary reaction, was proposed. Two different feeds with the mole ratio of MeOAc to MeOH at 1:1 and 1:9 were studied, and the effect of the operating pressure, the feed location and the reflux ratio on the RD column was analyzed. The simulations of reactive distillation were performed using a three phase non-equilibrium model implemented by gPROMS. As the limit of the reaction rate of MeOH dehydration, it is impossible to get 100% conversion of MeOAc and MeOH by a single RD column. Therefore, two novel processes for recovery of methyl acetate in PVA production were developed. The simulation results show that the high purity of dimethyl ether (DME) could be achieved with a complete conversion of MeOAc, and a large amount of energy demand and equipment costs can be reduced.     

醋酸甲酯水解的新工艺

提出醋酸甲酯水解的新工艺，并进行了处理量、进料分水比及回流比等操作因素对醋酸甲酯转化率影响规律的研究。醋酸甲酯的转化率随处理量的增加而降低，随回流比的增加而增大。当小于０．７，进料分水比对醋酸甲酯转化率的影响较为显著，并存在最佳操作值     

催化精馏水解醋酸甲酯研究

建立了一套催化精馏的小试装置 ,对催化精馏工艺在聚乙烯醇 (PVA)生产中取代固定床工艺水解醋酸甲酯(MeOAc)进行了实验研究。对催化精馏过程中影响MeOAc水解效果的 3个主要因素 :进料水酯比Rm,回流进料比Rf 及空速S ,进行了较详细的讨论 ,并与固定床工艺的水解效果进行了对比。结果表明 ,与固定床工艺相比 ,采用催化精馏工艺水解MeOAc可以大幅提高MeOAc转化率 ,并节省大量能量     

反应与精馏耦合水解醋酸甲酯(英文)

A process composed of a fixed-bed and a distillation column with a side withdraw, mainly methanol, is developed to hydrolyze methyl acetate (MA) as a typical byproduct in polyvinyl alcohol (PVA) and pure terephthalic acid (PTA) factory. The process is simulated by employing the equilibrium stage model RadFrac and plug flow model Rplug in Aspen Plus. Experiments are also carried out in a lab-scale to evaluate the process. The results show that at the molar ratio of water to methyl acetate about 4.0-5.0 in the feed stream and the volume ratio of distillate to feed MA above a critical value, the side product contains more than 80% (by mass) (MeOH) and less than 2% (by mass) MA, while the bottom contains more than 46% (by mass) acetic acid (HAc) and less than 0.5% (by mass) methanol with almost complete conversion of MA. Compared with the old catalytic distillation process we proposed before, this process can cut down 47.6% energy consumption and a distillation column.     

“背包式”反应精馏水解乙酸甲酯的工艺

采用“背包式”反应精馏深度水解乙酸甲酯,考察了工艺条件对水解率和酸水比的影响,并与传统的单塔催化精馏工艺进行了对比。结果表明：提高水酯比可以显著提高乙酸甲酯的水解率;回流进料比的增加有利于提高水解率但会增加能耗,较佳回流比为3.0左右;乙酸甲酯水解率随空速的增加而降低的速度较慢,可以适当提高空速以增加处理能力;增加固定床体积有利于酯的预水解,但是不一定有利于酯的总转化率。采用“背包式”催化精馏工艺可以实现乙酸甲酯的深度水解,且优于传统的单塔催化精馏工艺。     

001×7（732）阳离子交换树脂催化醋酸甲酯 水解反应过程模拟与优化

在充分搅拌和可忽略粒度影响条件下，测定了间歇搅拌反应釜中001×7（732）阳离子交换树脂催化醋酸甲酯水解反应动力学数据，建立了其拟均相与非均相反应动力学模型，进行了模型筛选和参数估值。结果表明，醋酸甲酯与水均吸附，表面反应为控制步骤的非均相反应动力学模型能较好地拟合实验数据，并满足统计检验。根据优选的反应动力学模型，对醋酸甲酯水解过程进行了模拟计算，考察了反应温度、树脂浓度、水酯摩尔比对水解过程的影响，得到的优化反应条件为：反应温度55℃、树脂浓度260 g·L^-1、水酯摩尔比1.5∶1。此时反应90 min接近醋酸甲酯平衡水解率34.8%。     

醋酸甲酯催化精馏水解过程模拟

利用醋酸甲酯水解体系热力学、水解反应动力学以及催化填料的基础数据,采用化工流程模拟与分析的方法,系统地对醋酸甲酯催化精馏水解过程进行了模拟研究。通过与实验数据进行对比,验证了该模拟方法的正确性。通过对工艺条件的灵敏度分析,获得该过程较优的工艺参数。在对现有工艺流程模拟的基础上,结合工业实际操作,提出两种工艺改进方案。     

乙酸甲酯催化精馏水解工艺研究

采用阳离子交换树脂为催化剂 ,研究了乙酸甲酯催化精馏水解工艺。反应区充填离子交换树脂催化剂捆束包 ,提馏段充填Mo Ti金属板波纹丝网填料。在小试、中试 (塔径为 2 0 0mm)和工业化 (塔径为1 0 0 0mm)实验中 ,系统地研究了水酯摩尔比、回流进料比和空速对酯分解率和分解液中酸水质量比的影响 ,获得不改变现有聚乙烯醇生产中乙酸甲酯分解回收工艺流程的最佳分解率为 50 %— 60 % ,由此导致比原工艺节能约 30 %和原有设备利用率成倍提高     

醋酸甲酯水解催化精馏过程的模拟计算

采用非平衡级速率模型对醋酸甲酯水解的催化精馏中试过程进行了模拟计算,考察了回流进料比、进料水酯比和酯进料位置等的变化对醋酸甲酯水解率的影响, 不仅证实了中试实验所得的结论,还获得了难以通过实验取得的结果.     

催化精馏塔内甲酸甲酯水解制甲酸的研究

在催化精馏塔内以压制的强酸性阳离子交换树脂为催化剂填料对甲酸甲酯水解制甲酸进行了实验研究.在全回流操作条件下,通过改变操作参数获得了高于90%的水解转化率.考虑到反应过程中水的阻碍作用,根据实验结果提出了可用于催化精馏过程的动力学方程并建立了基于平衡级理论的反应与分离耦合的数学模型.通过设定进料水酯摩尔比、回流与进料比、反应段与分离段理论级数等参数获得了水解过程的仿真结果,并提出了较佳的工艺操作条件.研究表明:仿真结果与实测数据相吻合;通过改变操作条件可调整反应段内水与甲酸甲酯的浓度,提高水解速度;增加反应段的高度比增加分离段的高度更有利;产品甲醇和甲酸在催化精馏塔内能够完全分离,反应段两端反应速度高于中间段的反应速度.     

乙酸甲酯的催化精馏水解实验研究

在自行设计的催化精馏塔中,以Amberlyst 35wet阳离子交换树脂为催化剂,全回流操作下,对乙酸甲酯催化精馏水解进行了研究。考察了空速、塔高度、回流进料比(体积比)以及进料中水酯物质的量比等操作条件对水解反应的影响。实验结果表明,在空速0.09 min-1,催化剂装填高度80 cm,提馏段7块塔板,回流进料比5∶1,进料中水酯物质的量比6.5∶1时,乙酸甲酯水解率达到83.5%。     

Synthesis of High‐Purity Methylal via Extractive Catalytic Distillation

An integrated continuous process, which combines catalytic distillation and extractive distillation in one column, is investigated for the synthesis of high‐purity methylal from methanol and formalin in the presence of a cation‐exchange resin catalyst. A feed with methanol:formaldehyde 2:1 molar ratio is chosen to evaluate the effects of operating parameters, such as extractant feeding position, ratio of extractant to feed, reflux ratio, and reboiler temperature, on the continuous synthesis of methylal. Under the optimum operating conditions and with water as extractant, the extractive catalytic distillation process operated continuously, producing a methylal purity of 98.7 % (H₂O: < 1.30 %) with 98.0 % formaldehyde conversion.     

2,3-丁二醇分离纯化中反应精馏的实验和模拟

对反应萃取-水解精馏法分离发酵液中2,3-丁二醇工艺中的水解精馏进行了实验和模拟研究。实验验证了4,5-二甲基-2-丙基-1,3-二氧戊环(DPD)水解精馏得到2,3-丁二醇的可行性。采用Aspen Plus建立反应精馏模型,以UNIFAC为热力学方程,RadFrac为反应精馏模块,对常压下DPD的水解精馏进行模拟,模拟结果与实验结果吻合较好。以2,3-丁二醇的收率为主要优化目标,考察最佳塔板数、进料位置、进料比、回流比和塔顶馏出比。模拟结果表明,在最佳操作条件下,塔釜2,3-丁二醇的收率为0.981,摩尔分率为0.150。     

温度对丙酮连氮水解制肼反应动力学的影响

利用自制的丙酮连氮,在间隙搅拌式高压反应釜中,研究其在一定的温度范围内水解制取水合肼的反应过程,考察了反应过程中反应压力、丙酮连氮与水的摩尔比和反应温度等因素对丙酮连氮转化率的影响。探讨了在413.15—443.15 K下水解反应的本征动力学,采用拟均相可逆反应的动力学模型进行拟合,并利用最小二乘法进行非线性回归得到了相应的动力学方程。结果表明:在实验条件下,水解反应为可逆吸热反应,且正反应的活化能远高于逆反应的活化能,升高温度平衡常数K增大,从而可增大丙酮连氮的转化率,其动力学参数为反应精馏制取水合肼的模拟优化设计提供了参考数据。     

响应面法优化一水硫酸氢钠流化催化精馏生产乙酸乙酯工艺条件

以新型的一水硫酸氢钠为催化剂,采用粉末状催化剂混合乙酸一起进料的加入方式,即流化催化精馏工艺,并利用响应面法优化乙酸乙酯催化精馏过程条件.首先,通过单因素灵敏度分析法对乙酸进料量、酸醇进料摩尔比、回流比、催化剂用量、釜底加热功率5个因素进行实验考察,确定了乙酸进料量、酸醇摩尔进料比、回流比3个关键因素的优化值及取值范围.根据单因素实验结果与精馏塔设备要求,塔釜加热功率和催化剂用量分别设定为68 W和2.0%(质量分数)乙酸,采用中心组合设计原则对乙酸进料量、酸醇进料摩尔比和回流比3个关键因素进行实验设计.以乙醇转化率为响应值,基于响应实验结果,利用响应面法对实验结果进行了方程回归,得到3个关键因素与响应值的二次关联模型.通过方差分析和平行实验,证明该模型准确可用.优化后的乙酸乙酯流态化催化精馏工艺条件为乙酸进料量3.2 mol·h^-1,酸醇进料摩尔比为3.1,回流比为3.3,在此优化条件下进行实验,乙醇转化率为88.67%,比基于单因素灵敏度分析法得到的优化工艺条件下乙醇转化率高1.0%.     

用人工神经网络模型模拟催化精馏塔

尝试用人工神经网络模型模拟醋酸甲酯水解催化精馏塔的操作过程,并寻求最佳工艺条件。以进料水酯比、回流进料比和醋酸甲酯的体积流率与催化剂体积比作为输入层的三个节点,醋酸甲酯的转化率和塔釜中的酸水比为输出层的两个节点,采用ＢＰ算法结合模拟退火算法,利用小试实验数据训练网络并检验训练结果;内插或外推一系列假想的工艺条件,让网络预测操作结果,最后确定最佳操作目标,通过网络模型寻找一组最佳工艺条件。结果表明：以充足可靠的实验数据为基础,神经网络模型能精确预测实验结果;利用人工神经网络模型对工艺条件进行优化,可取得令人满意的结果。     

Experimental Studies on the Catalytic Distillation for Hydrolysis of Methyl Acetate

In this paper, the feasibility of applying catalytic distillation for the hydrolysis of methyl acetate is studied experimentally. An optimum technological process for the hydrolysis is determined, based on experimental results and mathematical simulations. The methyl acetate conversion can be greatly increased, and the energy consumption reduced, for certain operation conditions via the catalytic distillation process.     

Investigations on the Synthesis of Methyl Acetate in a Heterogeneous Reactive Distillation Process

The production of methyl acetate in a reactive distillation process – prior art for 15 years – is often used as an example to study the basic phenomena of reactive distillation. The present paper deals with a theoretical and experimental analysis of methyl acetate synthesis in a reactive distillation column. A design method based on the interpretation of reactive distillation line diagrams is used to identify the main process parameters and to provide a foundation for experimental investigation. The significant influence of the reflux ratio on the conversion in the column is shown by mini plant experiments using supported ion exchanger in the form of Raschig rings as a heterogeneous catalyst. These experiments demonstrate the catalytic quality of this packing material. To simulate the reactive distillation column with a simple stage-to-stage method, the separation efficiency of the catalytic rings is investigated. Comparison of experimental and simulation results reveals that a simple model based on the assumption of simultaneous chemical and phase equilibrium describes the experimental data quite well over a wide range of reflux ratios. Furthermore, simulation results show that the conversion depends less on the number of reactive stages than on the use of two feed stages.     

浆料催化精馏制备甲缩醛

研究了以甲醇和甲醛为原料,以大孔径强酸性阳离子交换树脂为催化剂,通过浆料催化精馏工艺制备甲缩醛的可行性。考察了催化剂含量、进料醇醛比、进料总流量和回流比等因素对该过程的影响。在选定的试验条件下,甲缩醛收率可达89%以上,塔顶甲缩醛的质量分数可达0.99以上。结果表明,该工艺用于制备甲缩醛是可行的。