Distribution of pyrochlore phase in Pb(Mg1/3Nb2/3)O3-PbTiO3 films and suppression with a Pb(Zr0.52Ti0.48)O3 interfacial layer

Thin films of the relaxor ferroelectric Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (PMN-PT) on Pt/Ti/SiO₂/Si (Pt/Si) substrates both with and without a Pb(Zr_0.52Ti_0.48)O₃ (PZT) interfacial layer were investigated. Perovskite and pyrochlore coexistence was observed for PMN-PT thin films without a PZT interfacial layer. Interestingly, most of the pyrochlore phase was observed in single-coated films and in the first layer of multi-coated films. The pyrochlore phase exhibited grains with an average size of about 25 nm, which is smaller than those of the perovskite phase (about 90 nm). In contrast, for PMN-PT thin films grown on a PZT interfacial layer, the formation of a pyrochlore phase at the interface between PMN-PT layers and the substrate is completely suppressed. Moreover, small grains are not observed in the films with a PZT interfacial layer. The measured polarization-electric field (P-E) hysteresis loops of PMN-PT films with and without PZT layers indicate that enhanced electrical properties can be obtained when a PZT interfacial layer is used. These enhanced properties include an increase in the value of remanent polarization P_r from 2.7 to 5.8 μC/cm² and a decrease in the coercive field E_c from 60.5 to 28.0 kV/cm.     

Enhanced ferroelectric properties of Pb(Zr0.80Ti0.20)O3/PbO thin films prepared by radio frequency magnetron sputtering

The Pb(Zr_0.80Ti_0.20)O₃ (PZT) thin films with and without a PbO buffer layer were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by radio frequency (rf) magnetron sputtering method. The PbO buffer layer improves the microstructure and electrical properties of the PZT thin films. High phase purity and good microstructure of the PZT thin films with a PbO buffer layer were obtained. The effect of the PbO buffer layer on the ferroelectric properties of the PZT thin films was also investigated. The PZT thin films with a PbO buffer layer possess better ferroelectric properties with higher remnant polarization (P_r = 25.6 μC/cm²), and lower coercive field (E_c = 60.5 kV/cm) than that of the films without a PbO buffer layer (P_r = 9.4 μC/cm², E_c = 101.3 kV/cm). Enhanced ferroelectric properties of the PZT thin films with a PbO buffer layer is attributed to high phase purity and good microstructure.     

The thickness effect of Bi3.25La0.75Ti3O12 buffer layer in PbZr0.58Ti0.42O3/Bi3.25La0.75Ti3O12 (PZT/BLT) multilayered ferroelectric thin films

A series of PbZr_0.58Ti_0.42O₃ (PZT) thin films with various Bi_3.25La_0.75Ti₃O₁₂ (BLT) buffer layer thicknesses were deposited on Pt/TiO₂/SiO₂/p-Si(100) substrates by RF magnetron sputtering. The X-ray diffraction measurements of PZT film and PZT/BLT multilayered films illustrate that the pure PZT film shows (111) preferential orientation, and the PZT/BLT films show (110) preferential orientation with increasing thickness of the BLT layer. There are no obvious diffraction peaks for the BLT buffer layer in the multilayered films, for interaction effect between the bottom BLT and top PZT films during annealing at the same time. From the surface images of field-emission scanning electron microscope, there are the maximum number of largest-size grains in PZT/BLT(30 nm) film among all the samples. The growth direction and grain size have significant effects on ferroelectric properties of the multilayered films. The fatigue characteristics of PZT and PZT/BLT films suggest that 30-nm-thick BLT is just an effective buffer layer enough to alleviate the accumulation of oxygen vacancies near the PZT/BLT interface. The comparison of these results with that of PZT/Pt/TiO₂/SiO₂/p-Si(100) basic structured film suggests that the buffer layer with an appropriate thickness can improve the ferroelectric properties of multilayered films greatly.     

Stress-induced shifting of the morphotropic phase boundary in sol-gel derived Pb(Zr0.5Ti0.5)O3 thin films

The structure evolution of Pb(Zr_0.5Ti_0.5)O₃ thin films with different thicknesses on the Pt(1 1 1)/Ti/SiO₂/Si substrates has been investigated using X-ray diffraction and Raman scattering. Differing from Pb(Zr_0.5Ti_0.5)O₃ bulk ceramic with a tetragonal phase, our results indicate that for PZT thin films with the same composition monoclinic phase with Cm space group coexisting with tetragonal phase can appear. It is suggested that tensile stress plays a role in shifting the morphotropic phase boundary to titanium-rich region in PZT thin films. The deteriorated ferroelectric properties of PZT thin films can be attributed mainly to the presence of thin non-ferroelectric layer and large tensile stress.     

Enhanced ferro- and piezoelectric properties in (100)-textured Nb-doped Pb(ZrxTi1 − x)O3 films with compositions at morphotropic phase boundary

To develop high-performance piezoelectric films on conventional Pt(111)/Ti/SiO₂/Si(100) substrates, sol-gel-derived highly [100]-textured Nb-doped Pb(Zr_xTi_1 − x)O₃ (PNZT) thin films with different Zr/Ti ratios ranging from 20/80 to 80/20 were prepared and characterized. The phase structure, ferroelectric and piezoelectric properties of the PZNT films were investigated as a function of Zr/Ti ratios, and it was confirmed that there was distinct phase transition of the PNZT system from tetragonal to rhombohedral when the Zr/Ti ratio varied across the morphotropic phase boundary (MPB). The Nb-doped PZT films showed enhanced remanent polarization but reduced coercive field, whose best values reached 75 μC/cm² and 82 kV/cm, respectively at the composition close to MPB. In addition, the [100]-textured PNZT film at MPB also shows a high piezoelectric coefficient up to 161 pm/V. All these properties are superior to those for undoped PZT films.     

Composition dependent preferential orientation, dielectric and ferroelectric properties of Pb(ZrxTi1 − x)O3 thin films derived by sol-gel process

Pb(Zr_xTi_1 − x)O₃ (x = 0.35, 0.40, 0.60, 0.65) thin films were prepared by sol-gel spin on technique. From the X-ray diffraction analysis, PZT films with Zr-rich compositions (x = 0.60 and 0.65) had (111) preferential orientation and the preferential orientation changed to (100) for Ti-rich compositions (x = 0.35 and 0.40). The dielectric measurements on the above compositions at room temperature showed that the dielectric constant values were higher in Zr-rich compositions compared to Ti-rich compositions. The ferroelectric behavior measured in terms of the remnant polarization (P_r) and coercive field (E_c) up to an applied field of 260 kV/cm depicted that the Zr-rich PZT films with (111) preferential orientation had higher P_r and lower E_c values compared to the Ti-rich PZT films with (100) preferential orientation can be understood from the domain switching mechanism.     

Enhanced ferroelectric properties of epitaxial Pb(Zr,Ti)O3 film with LaAlO3 buffer

PbZr_0.52Ti_0.48O₃ films (PZT) have been grown epitaxially on SrRuO₃/LaAlO₃ (SRO/LAO) substrates using pulse laser deposition. In order to improve the ferroelectric properties of the PZT, one LAO buffer was introduced into the interface of PZT/SRO. The dependence of the electrical properties of the PZT films on the buffer thickness was studied. When a 10-nm-thick buffer was used, the remnant polarization (Pr) of the PZT film reached 58 ± 5 μC/cm², 2 times larger than the sample without any buffer layer. The leakage current was reduced 1-2 orders of magnitude. Besides, the PZT film with 10-nm-thick LAO buffer also exhibited good fatigue endurance after 10⁹ switching cycles. These results could propose one effective way to improve the properties of ferroelectric films deposited on oxide electrodes.     

Effect of annealing ambient on structure and ferroelectric properties of Pb(Zr0.4Ti0.6)O3 thin films on LaNiO3 coated Si substrates

Pb(Zr_0.4Ti_0.6)O₃ [PZT(40/60)] thin films were deposited onto LaNiO₃ (LNO) coated Si substrates by sol-gel technique. Three kinds of gases, air, O₂ and N₂, were used as the annealing ambient. The effect of the annealing ambient on their structure and ferroelectric properties was investigated. The results showed that both the films annealed in air and O₂ were the complete perovskite phase with (1 0 0) preferential orientation, while those annealed in N₂ were random orientation including some pyrochlore phases. As compared with the air ambient, either too much O₂ or too much N₂ was detrimental to the ferroelectric properties of PZT films. The difference in structure and ferroelectric properties was mainly associated with the intermediate phases and the concentration of domain pinning centers in the films.     

Magnetoelectric effect in Pb(Zr0.95Ti0.05)O3 and CoFe2O4 heteroepitaxial thin film composite

Multiferroic epitaxial films, include SrRuO₃/Pb(Zr_0.95Ti_0.05)O₃/CoFe₂O₄ has been successfully deposited on SrTiO₃ substrate by pulsed-laser deposition technique. The results show that the prepared films exhibit a single phase. The Pb(Zr_0.95Ti_0.05)O₃ (PZT) film was highly textured with (1 0 0) orientation and gives good ferroelectric properties with saturated polarization of 15 μC/cm². The magnetic coercivity of CoFe₂O₄ film on Pb(Zr_0.95Ti_0.05)O₃ has been dampened to 0.9 kOe. The anisotropic magnetically behavior of CoFe₂O₄ film was changed to isotropic by using high Zr concentrated PZT as underneath layer. Heterostructure films show a good ferromagnetic and ferroelectric coupling that lead to the large magnetoelectricity of 287 mV/cm Oe.     

Mechanical properties determined by nanoindentation tests of [Pb(Zr,Ti)O3] and [Pb(Mg1/3Nb2/3)1−xTixO3] sputtered thin films

As the introduction of piezoelectric materials into micro electromechanical systems increases, there is a correlating requirement for understanding the mechanical properties of these films. We have investigated the mechanical properties of unpoled PZT [Pb(Zr,Ti)O₃] and PMNT [Pb(Mg_1/3Nb_2/3)_1−xTi_xO₃] thin films deposited by sputtering. In this study, nano-indentation, a technique which allows determination of the transverse mechanical properties, is used. It is the easiest method for assessing the biaxial elastic modulus and the hardness of thin films. It was confirmed that neither cracks, nor pile-ups, were observed for indentation depths below 20% of the film's thickness.The continuous stiffness method was used and allowed us to demonstrate that the indentation modulus decreases continuously with increasing grain diameter. This can be explained by the orientation changes of the crystallites with increasing grain diameter. The indentation modulus measured under load, or at almost null load (that is when the ferroelectric domains are or are not oriented by the stress) are coherent with those determined by the same method with a hard bulk ceramic. These results tend to show that the compliance C_ij of the hard bulk ceramic can possibly be used with sputtered thin films. The hardness is almost independent of the grain diameter (H_b ≅ 7.5 ± 0.9 GPa) and higher than that for the bulk PZT ceramics considered in this study. PMNT and PZT films have appreciably the same mechanical characteristics. No influence of the film thickness was found on the values of both of these parameters.     

Structural and electrical characterizations of Bi(Zn0.5Ti0.5)O3 doped lead zirconate titanate ferroelectric films with enhanced ferroelectric properties

Bi(Zn_0.5,Ti_0.5)O₃ (BZT) doped Pb(Zr_0.4,Ti_0.6)O₃ (PZT) films were fabricated using a chemical solution deposition method and were characterized intensively in the present work. It was discovered that the room temperature remnant polarization and zero-field longitudinal piezoelectric constant of the BZT-doped PZT film were enhanced by 23% and 30%, respectively, as compared with those of the undoped PZT film prepared under the same experiment conditions. In order to explain the improved ferroelectric properties, the phase structures of the BZT-PZT and undoped PZT films were experimentally investigated in a broad temperature range (from 30 to 600 °C) by using the high temperature two-dimensional X-ray diffraction method. It was found that the improvement in ferroelectricity does not correspond to an elevated Curie temperature (T_C) or a substantially larger tetragonality (c/a). The difference on the change of T_C by doping of Bi-based perovskites in PZT solid solutions between this work and some previous investigations was explained on the basis of Zr/Ti ratio, and the necessity of an in-depth theoretical investigation was addressed.     

Pb(Zr0.52Ti0.48)O3/TiNi multilayered heterostructures on Si substrates for smart systems

Ferroelectric/shape memory alloy thin film multilayered heterostructures possess both sensing and actuating functions and are considered to be smart. In this article, Pb(Zr_0.52Ti_0.48)O₃ (PZT) ferroelectric thin films and Ti-riched TiNi shape memory alloy thin films have been deposited on Si and SiO₂/Si substrates in the 400-600 °C temperature range by pulsed laser deposition technique. Deposition processing, microstructure and surface morphology of these films are described. The TiNi films deposited at 500 °C had an austenitic B2 structure with preferred (110) orientation. The surfaces of the films were very smooth with the root-mean-square roughness on a unit cell level. The structure of the TiNi films had a significant influence on that of the subsequently deposited PZT films. The single B2 austenite phase of the TiNi favored the growth of perovskite PZT films. The PZT/TiNi heterostructures with the PZT and TiNi films respectively deposited at 600 and 500 °C exhibited a polarization-electric field hysteresis behavior with a leakage current of about 2 × 10^− 6 A/cm².     

Hydrothermal temperature effect on magnetoelectric coupling of Ni/Pb(Zr0.52Ti0.48)O3 bilayers

Magnetoelectric (ME) Ni/Pb(Zr_0.52Ti_0.48)O₃ bilayers have been prepared by hydrothermal method. The structure and ferroelectric properties of the Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films prepared at various hydrothermal temperatures are characterized by X-ray diffraction and ferroelectric testing. With the hydrothermal temperature increasing the grain size of the PZT thin films gradually decreases leading to a gradual increase of the coercive field and a decrease of the remnant polarization of the Ni/PZT bilayers. The ME voltage coefficient of the Ni/PZT bilayers gradually decreases as hydrothermal temperature increases. The large ME coefficient makes these Ni/PZT bilayers possible for applications in multifunctional devices such as electromagnetic sensor, transducers and microwave devices.     

Role of La0.5Sr0.5CoO3 template layers on dielectric and electrical properties of pulsed-laser ablated Pb(Nb2/3Mg1/3)O3-PbTiO3 thin films

Relaxor ferroelectric thin films of 0.7Pb(Mg_1/3Nb_2/3)O₃-0.3PbTiO₃ (PMN-PT) deposited on platinized silicon substrates with and without template layers were studied. Perovskite phase (80% by volume) was obtained through proper selection of the processing conditions on bare Pt/Ti/SiO₂/Si substrates. The films were initially grown at 300 °C using pulsed-laser ablation and subsequently annealed in a rapid thermal annealing furnace in the temperature range of 750-850 °C to induce crystallization. Comparison of microstructure of the films annealed at different temperatures showed change in perovskite phase formation and grain size etc. Results from compositional analysis of the films revealed that the films initially possessed high content of lead percentage, which subsequently decreased after annealing at temperature 750-850 °C. Films with highest perovskite content were found to form at 820-840 °C on Pt substrates where the Pb content was near stoichiometric. Further improvement in the formation of perovskite PMN-PT phase was obtained by using buffer layers of La_0.5Sr_0.5CoO₃ (LSCO) on the Pt substrate. This resulted 100% perovskite phase formation in the films deposited at 650 °C. Dielectric studies on the PMN-PT films with LSCO template layers showed high values of relative dielectric constant (3800) with a loss factor (tan δ) of 0.035 at a frequency of 1 kHz at room temperature.     

Compositionally graded Pb(Zr,Ti)O3 thin films with different crystallographic orientations

Compositionally graded ferroelectric PbZr_xTi_1−xO₃ (PZT) films were deposited using a sputtering method and crystallized in situ at 500 °C. The films showed purely (100) or (111) crystallographic orientation when grown on Si/SiO₂/TiO₂/Pt substrates, while they exhibited c-axis epitaxial microstructure when prepared on MgO/Pt substrates. Their crystallographic orientation was controlled owing to a thin TiO_x layer sputtered on substrates prior to PZT deposition. Analysis performed by Auger depth profile clearly confirmed the variation of composition in the films. Coercive fields from 80 kV/cm to 200 kV/cm and remnant polarization as large as 45 μC/cm² were obtained. However, no typical offset was observed on hysteresis loops, unlike previous works related to graded PZT films.     

Structural evaluation of sol-gel derived lead strontium titanate diffusion barrier for integration in lead zirconate titanate transducer design

Sol-gel derived Pb₄₀Sr₆₀TiO₃ (PST) thin film has been investigated as a diffusion barrier for integrating in PbZr₃₀Ti₇₀O₃ (PZT) device structures on Si substrates. PST film was deposited on SiO₂/Si substrate and annealed at a relatively low temperature range of 550-600 °C producing a crack-free, smooth and textured surface. Following deposition on PST/SiO₂/Si template PZT thin film was crystallised exhibiting random grain orientations and an insertion of the bottom Pt/Ti electrode forming PZT/Pt/Ti/PST/SiO₂/Si stacks promoted the preferred PZT (111) perovskite phase. PZT (111) peak intensity gradually decreased along with slight increase of the PZT (110) peak with increasing annealing temperature of the buffer PST film. The dielectric and ferroelectric properties of the PZT with barrier PST deposited at 550 °C were assessed. The dielectric constant and loss factor were estimated as 390 and 0.034 at 100 kHz respectively and the remnant polarisation was 28 µC/cm² at 19 V. The performance of the PZT/PST device structures was compared to similar PZT transducer stacks having widely used barrier TiO₂ layer.     

Effect of Pb(Fe1/2Nb1/2)O3 modification on dielectric and piezoelectric properties of Pb(Mg1/3Nb2/3)O3-PbZr0.52Ti0.48O3 ceramics

10 mol% Pb(Fe_1/2Nb_1/2)O₃ (PFN) modified Pb(Mg_1/3Nb_2/3)O₃-PbZr_0.52Ti_0.48O₃ (PMN-PZT) relaxor ferroelectric ceramics with compositions of (0.9 − x)PMN-0.1PFN-xPZT (x = 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8 and 0.9) were prepared. X-ray diffraction investigations indicated that as-prepared ceramics were of pure perovskite phase and the sample with composition of x = 0.8 was close to morphotropic phase boundary (MPB) between rhombohedral and tetragonal phase. Dielectric properties of the as-prepared ceramics were measured, and the Curie temperature (T_c) increased sharply with increasing PZT content and could be higher than 300 °C around morphotropic phase boundary (MPB) area. At 1 kHz, the sample with composition of x = 0.1 had the largest room temperature dielectric constant ?_r = 3519 and maximum dielectric constant ?_m = 20,475 at T_m, while the sample with composition of x = 0.3 possessed the maximum dielectric relaxor factor of γ = 1.94. The largest d₃₃ = 318 pC/N could be obtained from as-prepared ceramics at x = 0.9. The maximum remnant polarization (P_r = 28.3 μC/cm²) was obtained from as-prepared ceramics at x = 0.4.     

Effect of LaNiO3 electrodes and lead oxide excess on chemical solution deposition derived Pb(Zrx,Ti1 − x)O3 films

The effects of LaNiO₃ (LNO) and Pt electrodes on the properties of Pb(Zr_x,Ti_1 − x)O₃ (PZT) films were compared. Both LNO and PZT were prepared by chemical solution deposition (CSD) methods. Specifically, the microstructure of LNO and its influence on the PZT properties were studied as a function of PbO excess. Conditions to minimize the Pyrochlore phase and porosity were found. Remnant polarization, coercive field and fatigue limit were improved in the PZT/LNO films relative to the PZT/Pt films. Additionally, the PZT crystallization temperature over LNO was 500 °C, about ~ 50 °C lower than over Pt. The crystallization temperature reported here is amongst the lowest values for CSD-based PZT films.     

Epitaxial growth and electrical measurement of single crystalline Pb(Zr0.52Ti0.48)O3 thin film on Si(001) for micro-electromechanical systems

We report in this work the epitaxial growth and the electrical characteristics of single crystalline Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin film on SrTiO₃(STO)-buffered Si(001) substrate. The STO buffer layer deposited by molecular beam epitaxy allows a coherent oxide/Si interface leading enhanced PZT crystalline quality. 70 nm-thick PZT (52:48) layer was then grown on STO/Si(001) by sol-gel method. X-ray diffraction demonstrates the single crystalline PZT film on Si substrate in the following epitaxial relationship: [110] PZT (001)//[110] STO (001)//[100] Si (001). The macroscopic electrical measurements show a hysteresis loop with memory window of 2.5 V at ± 7 V sweeping range and current density less than 1 μA/cm² at 750 kV/cm. The artificial domains created by piezoresponse force microscopy with high contrast and non-volatile properties provide further evidence for the excellent piezoelectric properties of the single crystalline PZT thin film.     

Phase diagrams and polarization of single-domain epitaxial Pb(Zr1-xTix)O3 thin films

Within the framework of modified Landau-Devonshire thermodynamic theory, the equilibrium polarization states and physical properties of single-domain Pb(Zr_1-xTi_x)O₃ (PZT) thin films epitaxially grown on dissimilar cubic substrates are investigated. The “misfit strain-temperature” phase diagrams are obtained for several different compositions (x = 0.75, 0.65 and 0.55) of PZT films. The presence of stability range of the monoclinic phase is the characteristic feature of these phase diagrams, which separates the stability ranges of the tetragonal phase and the orthorhombic phase. Further analysis shows that the monoclinic phase widens with the increase of Zr content, and meanwhile the center shifts from positive values of the misfit strain towards zero.