膨化车间包装工房沾蜡工序泵蜡装置改进研究

膨化车间包装工房沾蜡工序泵蜡装置在生产过程中常因多种原因,存在安全隐患,通过改进抽蜡装置、熔蜡锅结构和加热盘管布置等措施,消除了安全隐患,实现了安全生产。     

检测凸轮轴窜动间隙的新型装置

为了科学准确地检测和调整喷油泵总成中凸轮轴轴向窜动间隙,最大限度地降低返工费用,设计了2套工序控制检测装置和1套成品检测装置,介绍了它们的设计原理和使用方法,对工序控制检测装置与成品检测装置进行的工艺试验表明,两者所获得的结果一致。     

PB反应器关键工序质量控制与检验

本文介绍了PB反应器关键工序的工艺方案研究 ,详细论述了关键工序应采取的工艺技术和过程质量控制措施 ,阐述了重要产品关键工序工艺方案研究的重要性     

一种换热器试样拉脱力检测装置设计与仿真

针对换热器管板与换热管结构特点,阐述了胀接工序的工艺过程以及拉脱力的测试方法,以此为依据设计了一种换热器试样拉脱力检测装置,对装置进行了设计与仿真。     

加氢反应器质量控制

加氢反应器是各种加氢工艺过程或加氢装置的核心关键设备,其制造工艺复杂、检验项目繁多、运行服役条件苛刻,操作危险性极高,是石化产品中的高端设备。本文主要介绍了加氢反应器各制造工序的流程及各关键工序的质量控制要点,通过一些列的质量控制手段,较好地保证了产品质量。     

双热源集成发电系统研究

阐述了烧结工序中烧结机烟气和冷却机废气两种余热分布规律及协同回收利用原则,对立式逆流冷却机、热废气-烟气双热源余热锅炉装置、三进口余热锅炉装置及双余热源集成发电系统进行了研究,并以宝钢2号烧结余热回收系统余热源参数为基础,在烧结机烟气和冷却机废气携带热量不变的工况下,对研发的集成发电系统选定两种方案与原余热回收方案进行...     

利用太阳能生产蒸烘干纺织品

本文叙述为纺织干燥工序提供热源的太阳能收集器装置。该装置用24个单轴跟踪抛物线槽形聚焦收集器来加热高温水回路中的水。再用这种高温水加热蒸汽发生器以提供生产用蒸汽,即太阳把水晒热的过程就是用滚筒烘燥器烘干纺织品的过程。     

工序质量控制在生产线管理中的应用

工序是产品、零部件制造过程的基本环节,也是生产组织过程的基本单位.机体、曲轴是柴油机构造中的主重要件,此次研究对象是机体、曲轴加工生产线,通过对加工生产线重点工序的过程控制,保证了产品的加工质量.     

高合金钢中氮含量控制分析

结合某钢厂高合金钢的实际生产情况,分析了精炼过程、连铸生产各个工序环节钢水含氮量的变化规律。通过现场各工序取样分析,研究各工序增氮的主要原因,提出改进建议并进行工业试验,为生产高品质的高合金钢在控氮方面给予指导意见。     

基于数控龙门钻床的带三通集箱找正的方法研究和应用

为了提高集箱找正的精准度和效率,通过对数控龙门钻床的激光检测装置和机械检测装置研究和应用,以带三通的集箱钻孔工序找正为例进行试验,结果表明,激光检测和机械检测方法在精准度和效率方面优于传统气泡水平仪,为后续集箱找正加工管孔提供实践依据和方法。     

Ash-forming elements in four Scandinavian wood species. Part 1: Summer harvest

Woody biomass in Finland and Sweden comprises mainly four wood species: spruce, pine, birch and aspen. To study the ash, which may cause problems for the combustion device, one tree of each species were cut down and prepared for comparisons with fuel samples. Well-defined samples of wood, bark and foliage were analyzed on 11 ash-forming elements: Si, Al, Fe, Ca, Mg, Mn, Na, K, P, S and Cl. The ash content in the wood tissues (0.2–0.7%) was low compared to the ash content in the bark tissues (1.9–6.4%) and the foliage (2.4–7.7%). The woods’ content of ash-forming elements was consequently low; the highest contents were of Ca (410–1340 ppm) and K (200–1310), followed by Mg (70–290), Mn (15–240) and P (0–350). Present in the wood was also Si (50–190), S (50–200) and Cl (30–110). The bark tissues showed much higher element contents; Ca (4800–19,100 ppm) and K (1600–6400) were the dominating elements, followed by Mg (210–2400), P (210–1200), Mn (110–1100) and S (310–750), but the Cl contents (40–330) were only moderately higher in the bark than in the wood. The young foliage (shoots and deciduous leaves) had the highest K (7100–25,000 ppm), P (1600–5300) and S (1100–2600) contents of all tissues, while the shoots of spruce had the highest Cl contents (820–1360) and its needles the highest Si content (5000–11,300). This paper presented a new approach in fuel characterization: the method excludes the presence of impurities, and focus on different categories of plant tissues. This made it possible to discuss the contents of ash element in a wide spectrum of fuel-types, which are of large importance for the energy production in Finland and Sweden.     

NEXT GENERATION ENGINEERED MATERIALS FOR ULTRA SUPERCRITICAL STEAM TURBINES

正1 ABSTRACT To reduce the effect of global warming on our climate,the levels of CO2emissions should be reduced.One way to do this is to increase the efficiency of electricity production from fossil fuels.This will in turn reduce the amount of CO2emissions for a given power output.Using US practice for efficiency calculations,then a move from a typical US plant running at 37%efficiency to a 760℃/38.5 MPa(1 400/5 580 psi)plant running at 48%efficiency would reduce CO2emissions by 170kg/MW.hr or 25%.     

Performance assessment of some ice TES systems

In this paper, a performance assessment of four main types of ice storage techniques for space cooling purposes, namely ice slurry systems, ice-on-coil systems (both internal and external melt), and encapsulated ice systems is conducted. A detailed analysis, coupled with a case study based on the literature data, follows. The ice making techniques are compared on the basis of energy and exergy performance criteria including charging, discharging and storage efficiencies, which make up the ice storage and retrieval process. Losses due to heat leakage and irreversibilities from entropy generation are included. A vapor-compression refrigeration cycle with R134a as the working fluid provides the cooling load, while the analysis is performed in both a full storage and partial storage process, with comparisons between these two. In the case of full storage, the energy efficiencies associated with the charging and discharging processes are well over 98% in all cases, while the exergy efficiencies ranged from 46% to 76% for the charging cycle and 18% to 24% for the discharging cycle. For the partial storage systems, all energy and exergy efficiencies were slightly less than that for full storage, due to the increasing effect wall heat leakage has on the decreased storage volume and load. The results show that energy analyses alone do not provide much useful insight into system behavior, since the vast majority of losses in all processes are a result of entropy generation which results from system irreversibilities.     

Aerodynamic performance effects of leading-edge geometry in gas-turbine blades

The purpose of this paper is to illustrate the advantages of the direct surface-curvature distribution blade-design method, originally proposed by Korakianitis, for the leading-edge design of turbine blades, and by extension for other types of airfoil shapes. The leading edge shape is critical in the blade design process, and it is quite difficult to completely control with inverse, semi-inverse or other direct-design methods. The blade-design method is briefly reviewed, and then the effort is concentrated on smoothly blending the leading edge shape (circle or ellipse, etc.) with the main part of the blade surface, in a manner that avoids leading-edge flow-disturbance and flow-separation regions. Specifically in the leading edge region we return to the second-order (parabolic) construction line coupled with a revised smoothing equation between the leading-edge shape and the main part of the blade. The Hodson–Dominy blade has been used as an example to show the ability of this blade-design method to remove leading-edge separation bubbles in gas turbine blades and other airfoil shapes that have very sharp changes in curvature near the leading edge. An additional gas turbine blade example has been used to illustrate the ability of this method to design leading edge shapes that avoid leading-edge separation bubbles at off-design conditions. This gas turbine blade example has inlet flow angle 0°, outlet flow angle −64.3°, and tangential lift coefficient 1.045, in a region of parameters where the leading edge shape is critical for the overall blade performance. Computed results at incidences of −10°,   −5°,   +5°,   +10° are used to illustrate the complete removal of leading edge flow-disturbance regions, thus minimizing the possibility of leading-edge separation bubbles, while concurrently minimizing the stagnation pressure drop from inlet to outlet. These results using two difficult example cases of leading edge geometries illustrate the superiority and utility of this blade-design method when compared with other direct or inverse blade-design methods.     

Effect of co-cultivation of Chlamydomonas reinhardtii with Azotobacter chroococcum on hydrogen production

Chlamydomonas reinhardtii cc124 and Azotobacter chroococcum bacteria were co-cultured with a series of volume ratios and under a variety of light densities to determine the optimal culture conditions and to investigate the mechanism by which co-cultivation improves H₂ yield. The results demonstrated that the optimal culture conditions for the highest H₂ production of the combined system were a 1:40 vol ratio of bacterial cultures to algal cultures under 200 μE m^?2 s^?1. Under these conditions, the maximal H₂ yield was 255 μmol mg^?1 Chl, which was approximately 15.9-fold of the control. The reasons for the improvement in H₂ yield included decreased O₂ content, enhanced algal growth, and increased H₂ase activity and starch content of the combined system.     

Natural-gas fueled spark-ignition (SI) and compression-ignition (CI) engine performance and emissions

Natural gas is a fossil fuel that has been used and investigated extensively for use in spark-ignition (SI) and compression-ignition (CI) engines. Compared with conventional gasoline engines, SI engines using natural gas can run at higher compression ratios, thus producing higher thermal efficiencies but also increased nitrogen oxide (NO_x) emissions, while producing lower emissions of carbon dioxide (CO₂), unburned hydrocarbons (HC) and carbon monoxide (CO). These engines also produce relatively less power than gasoline-fueled engines because of the convergence of one or more of three factors: a reduction in volumetric efficiency due to natural-gas injection in the intake manifold; the lower stoichiometric fuel/air ratio of natural gas compared to gasoline; and the lower equivalence ratio at which these engines may be run in order to reduce NO_x emissions. High NO_x emissions, especially at high loads, reduce with exhaust gas recirculation (EGR). However, EGR rates above a maximum value result in misfire and erratic engine operation. Hydrogen gas addition increases this EGR threshold significantly. In addition, hydrogen increases the flame speed of the natural gas-hydrogen mixture. Power levels can be increased with supercharging or turbocharging and intercooling. Natural gas is used to power CI engines via the dual-fuel mode, where a high-cetane fuel is injected along with the natural gas in order to provide a source of ignition for the charge. Thermal efficiency levels compared with normal diesel-fueled CI-engine operation are generally maintained with dual-fuel operation, and smoke levels are reduced significantly. At the same time, lower NO_x and CO₂ emissions, as well as higher HC and CO emissions compared with normal CI-engine operation at low and intermediate loads are recorded. These trends are caused by the low charge temperature and increased ignition delay, resulting in low combustion temperatures. Another factor is insufficient penetration and distribution of the pilot fuel in the charge, resulting in a lack of ignition centers. EGR admission at low and intermediate loads increases combustion temperatures, lowering unburned HC and CO emissions. Larger pilot fuel quantities at these load levels and hydrogen gas addition can also help increase combustion efficiency. Power output is lower at certain conditions than diesel-fueled engines, for reasons similar to those affecting power output of SI engines. In both cases the power output can be maintained with direct injection. Overall, natural gas can be used in both engine types; however further refinement and optimization of engines and fuel-injection systems is needed.     

Hydrogen production by steam-gasification of carbonaceous materials using concentrated solar energy – V. Reactor modeling,optimization, and scale-up

A chemical reactor for the steam-gasification of carbonaceous particles (e.g. coal, coke) is considered for using concentrated solar radiation as the energy source of high-temperature process heat. A two-phase reactor model that couples radiative, convective, and conductive heat transfer to the chemical kinetics is applied to optimize the reactor geometrical configuration and operational parameters (feedstock's initial particle size, feeding rates, and solar power input) for maximum reaction extent and solar-to-chemical energy conversion efficiency of a 5 kW prototype reactor and its scale-up to 300 kW. For the 300 kW reactor, complete reaction extent is predicted for an initial feedstock particle size up to 35 μm at residence times of less than 10 s and peak temperatures of 1818 K, yielding high-quality syngas with a calorific content that has been solar-upgraded by 19% over that of the petcoke gasified.     

Assessment methods of material ageing using Sdobyrev''s creep rupture model

The physical aspects of the activation energy, in higher and high temperatures, of the metal creep process were examined. The research results of creep-rupture in a uniaxial stress state and the criterion of creep-rupture in biaxial stress states, at two temperatures, are then presented. For these studies creep-rupture, taking case iron as an example the energy and pseudoenergy activation was determined. For complex stress states the criterion of creep-rupture was taken to be Sdobyrev's, i.e. σ_red = σ₁ β + (1 − β)σ_i, where: σ₁-maximal principal stress, σ_i-stress intensity, β-material constant (at variable temperature β = β(T)). The methods of assessment of the material ageing grade are given in percentages of ageing of new material in the following mechanical properties: 1) creep strength in uniaxial stress state, 2) activation energy in uniaxial stress state, 3) criterion creep strength in complex stress states, 4) activation pseudoenergy in complex stress states. The methods 1) and 3) are the relatively simplest because they result from experimental investigations only at nominal temperature of the structure work, however, for methods 2) and 4) it is necessary to perform the experimental investigations at least at two temperatures.     

Production of hydrogen from sewage biosolids in a continuously fed bioreactor: Effect of hydraulic retention time and sparging

Hydrogen was produced from primary sewage biosolids via mesophilic anaerobic fermentation in a continuously fed bioreactor. Prior to fermentation the sewage biosolids were heated to 70 °C for 1 h to inactivate methanogens and during fermentation a cellulose degrading enzyme was added to improve substrate availability. Hydraulic retention times (HRT) of 18, 24, 36 and 48 h were evaluated for the duration of hydrogen production. Without sparging a hydraulic retention time of 24 h resulted in the longest period of hydrogen production (3 days), during which a hydrogen yield of 21.9 L H₂ kg⁻¹ VS added to the bioreactor was achieved. Methods of preventing the decline of hydrogen production during continuous fermentation were evaluated. Of the techniques evaluated using nitrogen gas to sparge the bioreactor contents proved to be more effective than flushing just the headspace of the bioreactor. Sparging at 0.06 L L min⁻¹ successfully prevented a decline in hydrogen production and resulted in a yield of 27.0  L H₂ kg⁻¹ VS added, over a period of greater than 12 days or 12 HRT. The use of sparging also delayed the build up of acetic acid in the bioreactor, suggesting that it serves to inhibit homoacetogenesis and thus maintain hydrogen production.     

汽轮机数字电液调节系统挂闸异常的技术完善

分析了200MW汽轮机数字电液调节系统在运行中存在的挂闸异常问题,采取了相应的技术处理措施,且运行实践效果良好。