A single‐phase buck‐boost PFC converter with output‐voltage,ripple‐reducing operation

This paper describes a new single‐phase buck‐boost power‐factor‐correction (PFC) converter with output‐voltage, ripple reducing operation. The converter consists of a conventional buck‐boost PFC converter and an additional switch to obtain a freewheeling mode of the dc inductor current, and is operated by two modulators. The first modulator controls the buck‐boost switch to obtain PFC. The other modulator controls the square value of the instantaneous dc inductor current to perform the output‐voltage‐ripple‐reducing operation. In the two modulations, the time integral value of the input and output currents in each modulation period are controlled directly and indirectly, respectively. Thus, modulation errors or undesirable distortions of the input current and output voltage ripple are eliminated even if the dc inductor current produces large ripple in a low‐frequency range. The theories and combination techniques for the two modulators, implementation, and experimental results are described. © 1998 Scripta Technica, Electr Eng Jpn, 126(2): 56–70, 1999     

A novel active‐clamp zero‐voltage‐switching buck‐boost converter

An active‐clamp zero‐voltage‐switching (ZVS) buck‐boost converter is proposed in this paper to improve the performance of converter in light load condition. By employing a small resonant inductor, the ZVS range of switches could be adjusted to very light load condition. Moreover, 2 clamping capacitors are added in the converter to eliminate the voltage spike on the switches during transition. The operating principle of the proposed converter is analyzed, and the optimal design guide for full range ZVS is also provided. A 60‐W output prototype is experimentally built and tested in laboratory to verify the feasibility of proposed converter. The measured results show the critical ZVS operation of power switches at 1 and 0.7‐W output power for buck and boost mode, respectively. The peak conversion efficiency is up to 92.3%.     

Application of duality principle to synthesis of single‐stage power‐factor‐correction voltage regulators

The duality principle is applied to derive new single‐stage power‐factor‐correction (PFC) voltage regulators. This paper begins with an application of duality transformation to conventional discontinuous‐conduction‐mode buck, buck‐boost and boost converters. The resulting dual converters operate in the discontinuous capacitor voltage mode. These new converters provide the same PFC property, but in the dual manner. It is proved that in the practical case of the input being a voltage source, the mandatory insertion of inductance between the voltage input and the ‘dual PFC converter’ does not affect the power‐factor‐correcting property. A new single‐stage PFC regulator is derived by taking the dual of a well‐known circuit based on a cascade of conventional boost and buck converters. Analytical design expressions are derived, illustrating the relation between current stress and component values. Experiments are performed to confirm the operation of the circuit and its power‐factor‐correcting capability. Copyright © 2003 John Wiley & Sons, Ltd.     

Fast‐transient DC‐DC converter using a high‐performance error amplifier with a rapid output‐voltage control technique

This letter presents a method for improving the transient response of DC‐DC converters. The proposed technique replaces the conventional error amplifier with a combination of two different amplifiers to achieve a high loop gain and high slew rate. In addition, a rapid output‐voltage control circuit is employed to further reduce the recovery time. The proposed technique was applied to a four‐phase buck converter, and the chip was implemented using a 0.18‐μm CMOS process. The switching frequency of each phase was set at 2 MHz. Using a supply voltage of 2.7–5.5 V and an output voltage of 0.6–1.5 V, the regulator provided up to 2‐A load current with maximum measured recovery time of only 6.2 and 6.5 μs for increasing and decreasing load current, respectively. Copyright © 2017 John Wiley & Sons, Ltd.     

A new single‐phase high‐power‐factor converter with buck and buck–boost hybrid operation

In recent years, a wide variety of high‐power‐factor converter schemes have been proposed to solve the harmonic problem. The schemes are based on conventional boost, buck, or buck–boost topology, and their performance, such as output voltage control range in the boost and buck topology or efficiency in the buck–boost topology, is limited. To solve this, the authors propose a single‐phase high‐power‐factor converter with a new topology obtained from a combination of buck and buck–boost topology. The power stage performs the buck and buck–boost operations by a compact single‐stage converter circuit while the simple controller/modulator appropriately controls the alternation of the buck and buck–boost operation and maintains a high‐quality input current during both the buck and buck–boost operations. The proposed scheme results in a high‐performance rectifier with no limitation of output voltage control range and a high efficiency. In this paper, the principle and operation of the proposed converter scheme are described in detail and the theory is confirmed through experimental results obtained from 2‐kW prototype converter. © 2000 Scripta Technica, Electr Eng Jpn, 131(3): 91–100, 2000     

Single‐Inductor Dual‐Output DC–DC Converter Design Using RC Ripple Regulator Method

In this paper, we have proposed Single‐Inductor Dual‐Output (SIDO) buck–buck and boost–boost dc–dc converter using improved RC ripple regulator control. The proposed SIDO buck–buck converter has the characteristics of low‐ripple and high control frequency. RC ripple regulator control cannot be applied to SIDO boost–boost converter because RC ripple regulator undergoes self‐excited oscillation and two self‐excited oscillating controllers make the SIDO converter unstable. Thus we proposed the priority circuit for RC ripple regulator control. The proposed control circuit improves response characteristic and simplicity of the control circuit. Simulations are performed to verify the validity of the proposed SIDO converter. Simulation results indicate good performance of the proposed SIDO converter.     

High‐efficiency transformerless buck–boost DC–DC converter

A novel high‐efficiency transformerless buck–boost DC–DC converter is proposed in this paper. The presented converter voltage gain is higher than that of the conventional boost, buck–boost, CUK, SEPIC and ZETA converters, and high voltage gain can be obtained with a suitable duty cycle. The voltage stress across the power switch is low. Hence, the low on‐state resistance of the power switch can be selected to decrease conduction loss of the switch and improve efficiency. The input current ripple in the presented converter is low. The principle of operation and the mathematical analyses of the proposed converter are explained. The validity of the presented converter is verified by the simulation results in PSCAD/EMTDC software and experimental results based on the prototype circuit with 250 W and 40 kHz. Copyright © 2017 John Wiley & Sons, Ltd.     

Single‐stage single‐switch PFC converter for wide‐input extreme step‐down voltage applications

This paper presents a new single‐stage single‐switch high power factor correction AC/DC converter suitable for low‐power applications (< 150 W) with a universal input voltage range (90–265 V_rms). The proposed topology integrates a buck–boost input current shaper followed by a buck and a buck–boost converter, respectively. As a result, the proposed converter can operate with larger duty cycles compared with the existing single‐stage single‐switch topologies, hence, making them suitable for extreme step‐down voltage conversion applications. Several desirable features are gained when the three integrated converter cells operate in discontinuous conduction mode. These features include low semiconductor voltage stress, zero‐current switch at turn‐on, and simple control with a fast well‐regulated output voltage. A detailed circuit analysis is performed to derive the design equations. The theoretical analysis and effectiveness of the proposed approach are confirmed by experimental results obtained from a 100‐W/24‐V_dc laboratory prototype. Copyright © 2011 John Wiley & Sons, Ltd.     

Improved control‐to‐output characteristics of a PWM buck‐boost converter

An indirect control variable for improving the control‐to‐output characteristics of a Pulse Width Modulation (PWM) buck‐boost converter is introduced in this letter. The voltage gain and the small‐signal model of the buck‐boost converter are reviewed. The actual voltage command at one input of the PWM comparator is from the proposed indirect control variable and the peak value of the high‐frequency PWM carrier. The resulted voltage gain function appears proportional to this indirect control command. Also the dependence of the DC gain of the control‐to‐output transfer function on the duty cycle is eliminated. Experimental results conform well to the theoretical analysis. Copyright © 2010 John Wiley & Sons, Ltd.     

High‐power‐factor single‐switch AC to DC converter for LED lighting

In this paper, we report a novel single‐switch AC to DC step‐down converter suitable for light emitting diodes. The proposed topology has a buck and a buck–boost converter. The circuit is designed to operate in the discontinuous conduction mode in order to improve the power factor. In this topology, a part of the input power is connected to the load directly. This feature of the proposed topology increases the efficiency of power conversion, improves the input power factor, produces less voltage stress on intermediate stages, and reduces the output voltage in the absence of a step‐down transformer. The theoretical analysis, design procedure, and performance of the proposed converter are verified by simulation and experiment. A 36 V, 60 W prototype has been built to demonstrate the merits of this circuit. © 2017 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Non‐isolated single‐switch DC–DC converters with extended duty cycle for high step‐down voltage applications

Several new topologies of single‐switch non‐isolated DC–DC converters with wide conversion gain and reduced semiconductor voltage stress are proposed in this paper. Most of the proposed topologies are derived from the conventional inverse of SEPIC (Zeta) converter. The proposed topologies can operate with larger switch duty cycles compared with the existing single switch topologies, hence, making them well suitable for high step‐down voltage conversion applications. With extended duty cycle, the current stress in the active power switch is reduced, leading to a significant improvement of the system losses. Moreover, the active power switch in some of the proposed topologies is utilized much better compared to the conventional Zeta and quadratic‐buck converters. The principle of operation, theoretical analysis, and comparison of circuit performances with other step‐down converters are discussed regarding voltage and current stress and switch silicon utilization. Finally, simulation and experimental results for a design example of a 50 W/5 V at 42‐V input voltage operating at 50 kHz will be provided to evaluate the performance of the proposed converters. Copyright © 2014 John Wiley & Sons, Ltd.     

Implementation of parallel zero‐voltage switching converter with series‐connected transformers

This paper presents a parallel zero‐voltage switching (ZVS) DC–DC converter with series‐connected transformers. In order to increase output power, two transformers connected in series are used in the proposed converter. Two buck‐type converters connected in parallel have the same switching devices. The primary windings of series‐connected transformers can achieve the balanced secondary winding currents. The current doubler rectifiers with ripple current cancellation are connected in parallel at the output side to reduce the current stress of the secondary winding. Thus, the current ripple on the output capacitor is reduced, and the size of the output choke and output capacitor are reduced. Only two switches are used in the proposed circuit instead of four switches in the conventional parallel ZVS converter to achieve ZVS and output current sharing. Therefore, the proposed converter has less power switches. The ZVS turn‐on is implemented during the commutation stage of two complementary switches such that the switching losses and thermal stresses on the semiconductors are reduced. Experimental results for a 528‐W (48 V/11 A) prototype are presented to prove the theoretical analysis and circuit performance. Copyright © 2011 John Wiley & Sons, Ltd.     

One‐cycle controlled quadratic buck converter

The quadratic DC‐DC converter can broaden the voltage conversion ratio, which meets the requirements of wide input voltage. However, large‐scale variation of input voltage puts forward harsh requirements on ability to resist input disturbance of control strategy. Quadratic buck converter (QBC) is pulsed nonlinear dynamic systems, so the one‐cycle control strategy based on robustness principle may provide better rejection of power source than the linear feedback control. But the traditional one‐cycle controlled QBC (TOCCQBC) suffers from poor ability against load disturbance and steady‐state error. To overcome aforementioned shortages, an improved OCCQBC is proposed by adding inductor current to diode voltage as integral variable and introducing feedback of output voltage. The paper first introduces the working principle of the QBC, and second, the OCCQBC is presented. Then, a mathematical model using small signal analysis of the OCCQBC is established, and an experimental prototype with a power of 6 W is set up. Simulation and experimental results verify the correctness of the theoretical analysis and the feasibility of the strategy.     

Design and implementation of a digitally controlled single‐inductor dual‐output (SIDO) buck converter

This paper describes design and implementation of a digitally controlled single‐inductor dual‐output (SIDO) buck converter operating in discontinuous conduction mode. This converter adopts time‐multiplexing control in providing two independent output voltages using only an inductor. The design issues of the digital controller are discussed, including static and dynamic characteristics. Implementation of the controller, a modified hybrid digital pulse width modulator and a single look‐up table are developed. The digital controller was implemented on a field‐programmable gate array‐based control board. Experimental results demonstrating system validity are presented for a SIDO buck converter with nominal 3.6 V input voltage, and the outputs are regulated at 1.8 and 2.2 V. Copyright © 2012 John Wiley & Sons, Ltd.     

A White LED Driver Using a Buck–Boost Converter

For mobile backlighting applications, a white LED (WLED) driver using a buck–boost converter is proposed in this letter. Unlike conventional converters using boost converters, 2×/1.5× charge pumps, and so on, the proposed converter offers the negative stepped‐down voltage to drive the LED's cathode only when the input voltage is insufficient to drive a 1× transfer mode. Furthermore, unlike the LED backlight using charge pumps, the proposed converter can adjust the output voltage by controlling the duty factor of the clock pulse. Thus, the proposed converter can realize high power efficiency. The validity of the proposed converter is confirmed by simulations and experiments. © 2010 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Output current ripple reduction of LED driver using ceramic‐capacitor‐input circuit and buck‐boost converter

This article proposes an LED driver that consists of a ceramic‐capacitor‐input rectifier and a buck‐boost converter. The LED driver has an advantage of long life because it does not contain any electrolytic capacitors. However, the issue with electrolytic capacitor‐less LED driver is that the ripple of the smoothed voltage becomes large due to insufficient capacitance of the smoothing capacitor. The proposed method, which uses the discontinuous current mode of a buck‐boost converter, reduces the output current ripple under such conditions. Experimental results using a 5.7 W LED driver prototype demonstrate that the proposed method reduces the output current ripple and that the percent flicker becomes 4.4%, which is smaller than the recommended upper limit of 8%.     

A new non‐isolated free ripple input current bidirectional DC‐DC converter with capability of zero voltage switching

In this paper, a new nonisolated free ripple input current bidirectional dc‐dc converter with capability of zero voltage switching (ZVS) is proposed. The free ripple input current condition at low voltage side is achieved by using third winding of a coupled inductor and a capacitor for the whole range of duty cycles. In the proposed structure, the voltage conversion ratio can be more increased by adding the turn ratio of the second winding of the coupled inductor for the whole range of duty cycles. By adjusting the value of an auxiliary inductor in the topology of the converter, according to the power, the ZVS operation of the implemented 2 switches can be achieved throughout the whole power range. The mentioned features of proposed converter are validated theoretically for both boost and buck operations. In this paper, the proposed converter is analyzed for all operating modes. Moreover, all equations of the voltages and currents of all components, voltage conversion ratio, the required conditions for ZVS operation of switches, and also required conditions for canceling input current ripple at low voltage side are obtained. Finally, the performance of the proposed converter is reconfirmed through experimental and EMTDC/PSCAD simulation results.     

Analysis,modeling, and implementation of a new transformerless semi-quadratic Buck–boost DC/DC converter

This paper presents a novel transformerless semi-quadratic buck-boost converter (SQBuBoC). In the proposed SQBuBoC, two power switches with simultaneous operation are used and a higher step-up/step-down voltage conversion ratio is achieved compared with the traditional buck-boost, Cuk, single-ended primary-inductor converter, and Zeta converters. The positive polarity of the output voltage, along with low ripple continuous input current and common ground between the source and the output voltages, are some features that make the suggested topology more suitable for many applications with wide range of output voltage such as photovoltaic systems. Moreover, the total voltage stress across the power switches in this converter is lower than the cascade boost, and the traditional buck-boost converters led to power MOSFETs selection with lower drain-source ON resistance (R_ds) and efficiency improvement. All the steady-state analysis and comparisons in continuous conduction mode (CCM) are discussed in details. In addition, to study the low frequency behavior of the SQBuBoC by means of the state-space averaging technique, the small and large signal models of this converter in CCM are presented. Finally, the SQBuBoC analysis is justified using experimental results of a 50 W step-up 25 V to 120 V and a 28 W step-down 25 V to 14 V laboratory prototypes.     

Analysis and implementation of a high step‐up converter for fuel cell power‐generation systems

This paper presents a high step‐up converter, which utilizes a three‐winding coupled inductor and a rectified voltage‐doubler circuit to obtain high step‐up gain for fuel cells. The proposed converter functions as an active‐clamp circuit, which relieves large voltage spikes across the power switches. Thus, power switches with low‐voltage‐rated can be utilized to reduce conduction losses and circuit cost. Energy stored in leakage inductances of the coupled inductor is recycled to the output terminal, resulting in efficiency improvements. In addition, the coupled inductor in the presented converter can also have extra windings in order to achieve higher voltage gain. Finally, a prototype circuit with an input voltage of 60 V and an output voltage of 380 V is developed for a 1000 W‐rated fuel cell power‐generation system to validate its performance, and experimental waveforms and measured efficiency under different input voltages and output power level are demonstrated. Copyright © 2016 John Wiley & Sons, Ltd.     

An interleaved high step‐up DC‐DC converter with double boost paths

This paper proposed a novel high step‐up converter with double boost paths. The circuit uses two switches and one double‐path voltage multiplier cell to own the double boost and interleaved effects simultaneously. The voltage gain ratio of the proposed DC‐DC converter can be three times the ratio of the conventional boost converter such that the voltage stress of the switch can be lower. The high step‐up performance is in accordance with only one double‐path voltage multiplier cell. Therefore, the number of diodes and capacitors in the proposed converter can be reduced. Furthermore, the interleaved property of the proposed circuit can reduce the losses in the rectifier diode and capacitor. The prototype circuit with 24‐V input voltage, 250‐V output voltage, and 150‐W output power is experimentally realized to verify the validity and effectiveness of the proposed converter. Copyright © 2014 John Wiley & Sons, Ltd.