Rheology,composition, and peel-mechanism of block copolymer–tackifier-based pressure sensitive adhesives

Three samples of styrene–isoprene–styrene (S–I–S) block copolymers were chosen; copolymer A had 25% styrene, and copolymers B and C had 14% styrene. Copolymers A and B contained 20% diblock polymer and copolymer C contained 40% diblock polymer. All copolymers were mixed with a terpene type tackifier to make 56% and 48% weight tackifier concentration. These represent our model samples of pressure sensitive adhesives. The determination of tack, room-temperature peel-strength, and failure temperature under static shear were performed. The above results have been interpreted with the basic rheological data. The dynamic viscoelastic measurements and tensile stress–strain measurements were used. The effects of tackifier on the rubbery plateau moduli were treated with the Guth–Gold-type equation. The implications of the deviation from the equation are discussed in terms of the connectivity between polystyrene domains and the stability of the hard domains affected by inclusion of rubber segments.     

Effects of compatibility between tackifier and polymer on adhesion property and phase structure: Tackifier‐added polystyrene‐based triblock/diblock copolymer blend system

The effects of compatibility of tackifier with polymer matrix and mixing weight ratio of triblock/diblock copolymers as the matrix on the adhesion property and phase structure of tackifier‐added polystryrene triblock/diblock copolymer blends were investigated. For this purpose, polystyrene‐block‐polyisoprene‐block‐polystyrene triblock and polystyrene‐block‐polyisoprene diblock copolymers were used and the diblock weight ratio in the blend was varied from 0 to 1. Spherical polystyrene domains with a mean size of about 20 nm were dispersed in the polyisoprene (PI) continuous phase. In the case of the hydrogenated cycloaliphatic resin as tackifier having a good compatibility with PI and a poor compatibility with polystyrene, the peel strength increased with an increase of the tackifier content, and the degree of increase became significant above 40 wt % of tackifier. It was found that the nanometer‐sized agglomerates of tackifier in the PI matrix were formed and the distance between the nearest neighbors of agglomerates was about 15 nm from SAXS measurement. The peel strength increased with an increase of the nanometer‐sized agglomerates of tackifier from TEM observation. On the other hand, in the case of the rosin phenolic resin as tackifier having a good compatibility with both polystyrene and PI, the peel strength increased effectively at the lower tackifier content, while no significant increase at higher tackifier content was observed. The agglomerates of tackifier were never confirmed in this system. The higher peel strength was obtained at the diblock weight ratio in the blend of 0.5–0.7 for both tackifier‐added systems. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Poly(dimethylsiloxane‐b‐styrene) diblock copolymers prepared by reversible addition–fragmentation chain‐transfer polymerization: Synthesis and characterization

Well‐defined poly(dimethylsiloxane‐b‐styrene) diblock copolymers were prepared by reversible addition–fragmentation chain‐transfer (RAFT) polymerization. Monohydroxyl‐terminated polydimethylsiloxane was modified to form a functional polydimethylsiloxane/macro‐RAFT agent, which was reacted with styrene to form the diblock copolymers. The chemical compositions and structures of the copolymers were characterized by proton nuclear magnetic resonance spectroscopy, Fourier transform infrared spectroscopy, and gel permeation chromatography. The surface properties and morphology of the copolymers were investigated with static water contact‐angle measurements, X‐ray photoelectron spectroscopy, transmission electron microscopy, and atomic force microscopy, which showed a low surface energy and microphase separation surfaces that were composed of hydrophobic domains from polydimethylsiloxane segments. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Crystalline-crystalline poly(3-hexylthiophene)-polyethylene diblock copolymers: Solidification from the melt

We report on the development of the solid-state structure from the melt of crystalline-crystalline diblock copolymers consisting of the semiconducting poly(3-hexylthiophene) (P3HT) and insulating polyethylene (PE) - a material combination that previously was shown to feature promising characteristics for applications in flexible organic electronics. The nature of the structures obtained from the melt was found to generally be dictated by crystallization of the PE block, which solidified after the P3HT sequence. This resulted in the formation of classical spherulitic structures for diblock copolymers of low P3HT content. At P3HT contents exceeding 10-20 wt%, the semiconductor block increasingly hampered crystallization of the PE moiety, with the P3HT entity arranging into columnar and at higher content into lamellar micelle-type domains. Unlike the rate of crystal growth of the two moieties, interestingly, the dimensionality of both entities of the diblock copolymers was found to be unaffected by the presence of the dissimilar block.     

Synthesis, morphology and mechanical properties of linear triblock copolymers based on poly(α-methylene-γ-butyrolactone)

A series of well-defined triblock copolymers containing middle soft poly(n-butyl acrylate) (PBA) block and outer hard blocks of poly(α-methylene-γ-butyrolactone) homopolymer (PMBL) or random poly (α-methylene-γ-butyrolactone)-r-poly(methyl methacrylate) copolymer (PMBL-r-PMMA) were synthesized by atom transfer radical polymerization (ATRP). Phase separated morphologies of cylindrical or spherical hard block domains arranged in the soft PBA matrix were observed by atomic force microscopy and small-angle X-ray scattering. The mechanical and thermal properties of the copolymers were thoroughly characterized and their thermoplastic elastomer behavior was studied. Dynamic mechanical analysis (DMA) showed for all PMBL-b-PBA-b-PMBL copolymers a very broad rubbery plateau range extending up to temperatures of 300 °C. Replacement of the PMBL hard block with the less brittle PMBL-r-PMMA resulted in an improvement of the tensile properties, without compromising the very good thermal stability of the materials.     

The influence of styrene–butadiene diblock copolymer on styrene–butadiene–styrene triblock copolymer viscoelastic properties and product performance

The effects of the styrene–butadiene (SB) diblock copolymer on the viscoelastic properties of styrene–butadiene–styrene (SBS) triblock copolymers were examined in both in the the neat state and within specific product applications. The addition of the SB diblock copolymer into a pure SBS triblock copolymer resulted in a significant decrease in the plateau storage modulus and a quantitative linear rise in tan delta. In a pure triblock, in which all endblocks are anchored in polystyrene domains, all entanglements are physically trapped. The SB diblock embodies untrapped polybutadiene endblocks that are able to relax stress by chain reptation through the rubbery polybutadiene matrix. The SB diblock copolymer quantitatively lowered the microphase separation temperature (MST) of the SBS triblock copolymer. These changes in linear viscoelastic behavior manifest themselves into a reduction in the efficiency and performance of the SBS triblock copolymer in asphalt pavement binders and hot-melt adhesive blends. Specifically, the SB diblock diminished the complex shear modulus and elasticity of a polymer-modified asphalt, which translated into lower predicted rutting specification values. The increase in diblock content altered the viscoelastic response of the hot-melt adhesive blend, translating into a reduction in the shear holding power and shear adhesion failure temperature. The lack of network participation, coupled with the relaxation of the polybutadiene endblocks, accounts for the lower strength and greater temperature susceptibility of the diblock-containing systems. © 1995 John Wiley & Sons, Inc.     

Self‐assembled nanostructures: preparation,characterization, thermal,optical and morphological characteristics of amphiphilic diblock copolymers based on poly(2‐hydroxyethyl methacrylate‐block‐N‐phenylmaleimide)

A series of well‐defined amphiphilic poly[(2‐hydroxyethyl methacrylate)‐block‐(N‐phenylmaleimide)] diblock copolymers containing hydrophilic and hydrophobic blocks of different lengths were synthesized by atom transfer radical polymerization. The properties of the diblock copolymers and their ability to form large compound spherical micelles are described. Their optical, morphological and thermal properties and self‐assembled structure were also investigated. The chemical structure and composition of these copolymers have been characterized by elemental analysis, Fourier transform infrared, ¹H NMR, UV–visible and fluorescence spectroscopy, and size exclusion chromatography. Furthermore, the self‐assembly behavior of these copolymers was investigated by transmission electron microscopy and dynamic light scattering, which indicated that the amphiphilic diblock copolymer can self‐assemble into micelles, depending on the length of both blocks in the copolymers. These diblock copolymers gave rise to a variety of microstructures, from spherical micelles, hexagonal cylinders to lamellar phases. © 2013 Society of Chemical Industry     

Nanoscale localization of poly(vinylidene fluoride) in the lamellae of thin films of symmetric polystyrene-poly(methyl methacrylate) diblock copolymers

We employed thin film blends of diblock copolymers with functional homopolymers as a simple strategy to incorporate organic functional materials into nanodomains of diblock copolymers without serious synthesis. A blend pair of polystyrene-poly(methyl methacrylate) (PS-PMMA) diblock copolymers and poly(vinylidene fluoride) (PVDF) was selected as a model demonstration because PVDF is a well-known ferroelectric polymer and completely miscible with amorphous PMMA. Thin films of symmetric PS-PMMA copolymers provided the nanometer-sized PMMA lamellae, macroscopically parallel to the substrate, in which PVDF chains were dissolved. Thus, amorphous PVDF chains were effectively confined in the PMMA lamellae of thin film blends. The location of PVDF chains in the PMMA lamellae was investigated by the dependence of the lamellar period on the volume fraction of PVDF, from which we found that PVDF chains were localized in the middle of the PMMA lamellae. After the crystallization of PVDF, however, some of PVDF migrated to the surface of the film and formed small crystallites.     

Synthesis of azobenzene‐containing side chain liquid crystalline diblock copolymers using RAFT polymerization and photo‐responsive behavior

Well‐defined azobenzene‐containing side chain liquid crystalline diblock copolymers composed of poly[6‐[4‐(4‐methoxyphenylazo)phenoxy]hexyl methacrylate] (PAzoMA) and poly(glycidyl methacrylate) (PGMA) were synthesized by a two‐step reversible addition–fragmentation chain transfer polymerization (RAFT). The thermal liquid‐crystalline phase behavior of the PGMA‐b‐PAzoMA diblock copolymers in bulk were measured by differential scanning calorimetry (DSC) and polarized light microscopy (POM). The synthesized diblock copolymers exhibited a smectic and nematic liquid crystalline phase over a relatively wide temperature range. With increasing the weight fraction of the PAzoMA block, the phase transition temperatures, and corresponding enthalpy changes increased. Atomic force microscope (AFM) measurements confirmed the formation of the microphase separation in PGMA‐b‐PAzoMA diblock copolymer thin films and the microphase separation became more obvious after cross‐linking the PGMA block. The photochemical transition behavior of the PGMA‐b‐PAzoMA diblock copolymers in solution and in thin films were investigated by UV–vis spectrometry. It was found that the trans–cis isomerization of diblock copolymers was slower than that of the corresponding PAzoMA homopolymer and the photoisomerization rates decreased with increasing either the length of PAzoMA block or PGMA block. The photo‐induced isomerization in solid films was quite different with that in CHCl₃ solution due to the aggregation of the azobenzene chromophore. The cross‐linking structures severely suppressed the photoisomerization of azobenzene chromophore. These results may provide guidelines for the design of effective photo‐responsive anisotropic materials. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2165–2175, 2013     

MMA-DMAEMA两亲嵌段共聚物的合成

在室温下，采用苄醇钾(BzOK)作引发剂通过氧阴离子聚合方法合成了相对分子质量、嵌段组成均可控且相对分子质量分布窄的两亲嵌段共聚物BzO—MMA—DMAEMA和BzO—MMA—DMAEMA。用^1HNMR、FTIR、GPC对共聚物进行表征。比较不同加料次序所获得的嵌段共聚物，发现相同“单体／引发剂”条件下，共聚物的组成完全一致，从而证明MMA和DMAEMA的氧阴离子聚合反应体系均为活性聚合。     

Theory of chromatography of ring-shaped block copolymers

A theory is developed for describing liquid chromatography of ring diblock and multiblock copolymers. The chromatographic behavior of ring block copolymers at different adsorption interactions is analyzed theoretically and compared with that of linear block copolymers; typical chromatograms are simulated by using the theory. In particular, it is shown that under the critical interaction condition for one block the chromatographic retention of a ring diblock copolymer is dependent of the length of the ‘critical’ block; this behavior differs qualitatively from that of a linear diblock copolymer. Ring copolymers are always more retained than linear ones, therefore such copolymers can be separated. Especially good separation of heterogeneous ring and linear block copolymers is predicted at near-critical interaction conditions. According to the theory, ring diblocks and multiblocks can be separated as well, if one component of a copolymer is adsorbing, while the other one is not adsorbing.     

Influence of diblock copolymer on the morphology and properties of polystyrene/poly(dimethylsiloxane) blends

Blends of polystyrene (PS) and poly(dimethylsiloxane) (PDMS), with and without diblock copolymers (PS‐b‐PDMS), were prepared by melt mixing. The melt rheology behavior of the blends was studied with a capillary rheometer. The morphology of the blends was examined with scanning electron microscopy. The miscibility of the blends was studied with differential scanning calorimetry. The morphology of PS/PDMS blends was modified by the addition of PS‐b‐PDMS copolymers and investigated as a function of the molar mass of the diblock copolymers, viscosity ratios and the processing conditions. As investigated, the observed morphology of the melt‐blended PS/PDMS pair unambiguously supported the interfacial activity of the diblock copolymers. When a few percent of the diblock copolymers blended together with the PS and PDMS homopolymers, the phase size was reduced and the phase dispersion was firmly stabilized against coalescence. The compatibilizing efficiency of the copolymers was strongly dependent on its molar mass. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2747–2757, 2004     

Synthesis and characterization of amphiphilic PMTFPS‐b‐PEO diblock copolymers

A series of new amphiphilic poly[methyl(3,3,3‐trifluoropropyl) siloxane]‐b‐poly(ethyleneoxide) (PMTFPS‐b‐PEO) diblock copolymers with different ratio of hydrophobic segment to hydrophilic segment were prepared by coupling reactions of end‐functional PMTFPS and PEO homopolymers. PMTFPS‐b‐PEO diblock copolymers synthesized were shown to be well defined and narrow molecular weight distributed by characterizations such as NMR, GPC, and FTIR. Additionally, the solution properties of these diblock copolymers were investigated using tensiometry and transmission electron microscopy. Interestingly, the critical micellization concentration increases with increasing length of hydrophobic chain. Transmission electron microscopy studies showed that PMTFPS‐b‐PEO diblock copolymers in water preferentially aggregated into vesicles. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Control of the Surface Properties in Polymer Blends

We report on the preparation of amphiphilic diblock copolymers containing a hydrophilic segment, poly(acrylic acid)(PAA), and a polystyrene hydrophobic part. We analysed, by means of contact-angle measurements, how the hydrophilic segments usually bury themselves under the hydrophobic when exposed to air to reduce the surface free energy of the system. In contrast, in contact with water, the hydrophilic blocks have a tendency to segregate to the interface. We first describe the parameters that control the surface reconstruction when the environmental conditions are inversed from dry air to water vapour. Then, annealing time, temperature, composition and size of the diblock copolymers, and size of the matrix that influenced the surface migration process are the main parameters also considered. Finally, the density of the carboxylic functions placed at the surface was determined using the methylene blue method.     

The rubber particle size dependence of crazing in polypropylene

The tensile crazing and Charpy impact behavior of polypropylene modified with styrene-butadiene copolymer (SBR) and ethylene-propylene-diene monomer (EPDM) was studied. Various rubber particle size distributions were obtained by varying the relative viscosities between rubbery phase and PP matrix. Transmission electron microscopy and computer-aided image analysis were used to provide particle size information. In general, PP blends with smaller rubber particles are tougher and more ductile than those with larger particles, probably because the former represents a more efficient use of rubbery phase in promoting crazing and/or shear yielding. Samples with average particle diameter D? ≥ 0.5 μm were found to exhibit pronounced crazing. Within a given sample, no crazes appeared to develop around individual rubber particles with D < 0.5 μm. The higher the D, the greater the propensity to form crazes. The behavior of samples with D? ? 0.5 μm appeared to be dominated by shear yielding; very few crazes could be found. That there exists a critical rubber particle size is explained by the requirement that sufficient stress concentration be maintained to a finite radial distance to permit the initiation and growth of a craze, which requires a finite volume. Small particles, inducing smaller stress-enhanced zones, are therefore not effective in initiating crazes.     

Effect of polymer architecture on metal nanoclusters

Synthesis of metal nanoclusters in polymeric media has been shown to yield small clusters with a narrow size distribution. Embedding such clusters in the three-dimensional structures formed by diblock copolymers will allow the development of ordered structures with high optical and magnetic contrast between the different regions. In this paper we investigate the effect of homopolymer and diblock copolymer properties on the cluster size. We find that in homopolymer solutions, the cluster size reaches a minimum at a specific chain molecular weight (MW). In the case of diblock copolymers, the cluster size is set by the MW of the block with the stronger affinity to the metal surface.     

Amphiphilic diblock copolymers containing poly(N‐hexylisocyanate): Monolayer behavior at the air–water interface

The behavior of amphiphilic diblock copolymers containing 80–89% of poly(N‐hexylisocyanate) (PHIC) with different hydrophobic segments spread at the air–water interface has been studied. Surface pressure‐area isotherms (π‐A) at the air–water interface were determined. It was found that these diblock copolymers form stable monolayers and the isotherms present a pseudoplateau region at low surface pressure, irrespective of the nature of the partner block: poly(styrene) (PS) or poly(isoprene). Surface pressure variation at the semidilute region of the monolayer was expressed in terms of the scaling laws as power function of the surface concentration. The critical exponents of the excluded volume ν obtained for copolymers with PHIC and PS blocks are 0.58 for the copolymer with 85% of PHIC and 15% of PS, and 0.63 for the copolymer with 89% of PHIC and 11% of PS. The hydrophobicity degree of the diblock copolymers was estimated from the determination of the surface energy values by wettability measurements. The morphology of the monolayers was determined by means of Brewster angle microscopy. Molecular dynamic simulation was performed to explain the experimental behavior of diblock copolymers at the air–water interface. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology and micromechanical deformation behavior of styrene–butadiene block copolymers. IV. Structure–property correlation in binary block copolymer blends

The structure–property correlation in blends consisting of styrene/butadiene block copolymers forming alternating polystyrene (PS) and polybutadiene (PB) lamellae, and PS domains in rubbery matrix was investigated by different microscopic techniques (transmission electron microscopy, scanning force microscopy, and scanning electron microscopy), uniaxial tensile testing, and dynamic mechanical analysis. Unlike the pure lamellar block copolymer, the blends showed predominantly disordered wormlike morphology formed by the intermolecular mixing. These structures allowed a precise control of stiffness/toughness ratio of the blends over a wide range. The blends showed a gradual transition from predominantly viscoplastic to elastomeric behavior with increasing triblock copolymer content. The results demonstrated that the binary block copolymer blends provide the unique possibility of tailoring mechanical properties on the basis of nanostructured polymeric materials. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1219–1230, 2004     

A novel well-defined amphiphilic diblock copolymer containing perfluorocyclobutyl aryl ether-based hydrophobic segment

A series of well-defined binary hydrophilic-fluorophilic diblock copolymers were synthesized by successive atom transfer radical polymerization (ATRP) of methoxylmethyl acrylate (MOMA) and 4-(4′-p-tolyloxyperfluorocyclobutoxy)benzyl methacrylate (TPFCBBMA) followed by the acidic selective hydrolysis of the hydrophobic poly(methoxymethyl acrylate) (PMOMA) segment into the hydrophilic poly(acrylic acid) (PAA) segment. ATRP of MOMA was initiated by 2-MBP at 50 °C in bulk to give two different PMOMA homopolymers with narrow molecular weight distributions (M_w/M_n ≤ 1.15). PMOMA-b-PTPFCBBMA well-defined diblock copolymers were synthesized by ATRP of TPFCBBMA at 90 °C in anisole using Br-end-functionalized PMOMA homopolymer as macroinitiator and CuBr/PMDETA as catalytic system. The final PAA-b-PTPFCBBMA amphiphilic diblock copolymers were obtained via the selective hydrolysis of PMOMA block in dilute HCl without affecting PTPFCBBMA block. The critical micelle concentrations (cmc) of PAA-b-PTPFCBBMA amphiphilic copolymers in aqueous media were determined by fluorescence spectroscopy using pyrene as probe and these diblock copolymers showed different micellar morphologies with the changing of the composition.     

Study of novel biodegradable thermo‐sensitive hydrogels of methoxy‐poly(ethylene glycol)‐block‐polyester diblock copolymers

A series of biodegradable thermo‐sensitive hydrogels were synthesized by ring‐opening polymerization of methoxy‐poly(ethylene glycol) (mPEG) and various ester monomers, i.e. D ,L ‐lactide, glycolide, β‐propiolactone, δ‐valerolactone and ε‐caprolactone. The copolymers were characterized using ¹H NMR spectroscopy and gel permeation chromatography. The micelle properties were also measured. The results indicated that the diblock copolymers formed nano‐micelles at low concentrations in aqueous phase. The lower critical solution temperatures of the diblock copolymers were above 35 °C at 1 wt%. As the temperature increased above room temperature, the diblock copolymer solutions underwent a sol‐to‐gel phase transition, which was manifested in viscosity increases, indicative of the formation of a gel. The mPEG–polyester diblock copolymer solutions exhibited sol‐gel transition behavior as a function of temperature and polymer concentration. Copyright © 2010 Society of Chemical Industry