四边简支条件下正交各向异性蜂窝夹层板的固有特性分析

以四边简支正交各向异性矩形蜂窝夹层板为研究对象,应用Reissner-Mindlin夹层板剪切理论,在考虑横向剪切变形的基础上,给出了一种将夹层板弯曲控制方程组化为仅含一个位移函数的单一方程的方法,从而获得了四边简支条件下矩形蜂窝夹层板弯曲振动固有频率的精确解,理论结果与数值结果和实验结果取得很好的一致,验证了本文方法的合理性;在此基础上研究了面板、芯层的各项结构和材料设计参数对夹层板其固有频率的影响,并对各设计参数对夹层板固有频率的调控机理进行了分析。研究结果对蜂窝夹层板的结构设计和工程应用具有指导意义。     

明胶鸟弹撞击复合材料蜂窝夹芯板试验

开展明胶鸟弹撞击复合材料蜂窝夹芯板试验,研究夹芯结构在软体高速冲击下的损伤形式,分析相关因素对结构动态响应结果的影响。通过CT扫描对复合材料蜂窝夹芯板内部进行检测可知,面板出现分层、基体开裂、纤维断裂、凹陷、向胞内屈曲等损伤形式,蜂窝芯出现芯材压溃、与面板脱粘的损伤形式;分析复合材料蜂窝夹芯板后面板的动态变形过程及撞击中心处位移-时间数据可知,复合材料蜂窝夹芯板在撞击过程中出现由全局弯曲变形主导和局部变形主导的两种变形模式;通过对比不同工况下的复合材料蜂窝夹芯板损伤程度可知,复合材料蜂窝夹芯板损伤程度随鸟弹撞击速度的增加而增大;蜂窝芯高度为10 mm的复合材料蜂窝夹芯板较蜂窝芯高度为5 mm的复合材料蜂窝夹芯板的损伤程度大;初始动能较大的球形鸟弹较圆柱形鸟弹对复合材料蜂窝夹芯板造成的冲击损伤程度更大。      

Quasi-static indentation tests on aluminium foam sandwich panels

Mechanical response and energy absorption of aluminium foam sandwich panels subjected to quasi-static indentation loads were investigated experimentally. These sandwich panels consisted of two aluminium face-sheets and a closed cell aluminium foam core (ALPORAS®). Quasi-static indentation tests were conducted using an MTS universal testing machine, with sandwich panels either simply supported or fully fixed. Force–displacement curves were recorded and the total energy absorbed by sandwich panels was calculated accordingly. Videos and photographs were taken to capture the deformation of top face-sheets, foam cores and bottom face-sheets. Effects of face-sheet thickness, core thickness, boundary conditions, adhesive and surface condition of face-sheets on the mechanical response and energy absorption of sandwich panels were discussed.     

Development of a satellite structure with the sandwich T-joint

In this study, a monocoque satellite structure composed of many composite sandwich panels, which consist of two carbon fiber/epoxy composite faces and an aluminum honeycomb core, was designed to reduce structural mass and to improve static and dynamic structural rigidity. To join composite sandwich panels with T-shape joints, a new I-shape side insert, which was fixed inside the composite sandwich panel edge with film adhesive, was suggested. The composite sandwich panels were assembled with bolts using the through-the-thickness insert and the I-shape side insert. The flatwise tensile and compressive tests of the composite sandwich panels were performed with respect to the bonding pressure between the composite face and the aluminum honeycomb core to achieve an optimal bonding pressure. To investigate the joint characteristics of the composite faces and the I-shape side insert, cleavage peel tests were performed with respect to the bonding thickness. Also, a finite element model of the composite sandwich T-joint with the I-shape side insert was developed from experimental results of the impulse response tests and composite sandwich T-joint static tests. From the finite element analysis, the structural reliability of the monocoque composite sandwich satellite structure was verified.     

The structural response of clamped sandwich beams subjected to impact loading

The structural response of dynamically loaded monolithic and sandwich beams made of aluminum skins with different cores is determined by loading the end-clamped beams at mid-span with metal foam projectiles. The sandwich beams comprise aluminum honeycomb cores and closed-cell aluminum foam cores. Laser displacement transducer was used to measure the permanent transverse deflection of the back face mid-point of the beams. The resistance to shock loading is evaluated by the permanent deflection at the mid-span of the beams for a fixed magnitude of applied impulse and mass of beam. It is found that sandwich beams with two kind cores under impact loading can fail in different modes. Experimental results show the sandwich beams with aluminum honeycomb cores present mainly large global deformation, while the foam core sandwich beams tend to local deformation and failure, but all the sandwich beams had a higher shock resistance, then the monolithic beam. For each type of beams, the dependence of transverse deflection upon the magnitude of the applied impulse is measured. Moreover, the effects of face thickness and core thickness on the failure and deformation modes were discussed. Results indicated that the structural response of sandwich beams is sensitive to applied impulse and structural configuration. The experimental results are of worth to optimum design of cellular metallic sandwich structures.     

等腰梯形蜂窝芯玻璃钢夹芯板的面内压缩性能

为研究等腰梯形蜂窝芯玻璃钢夹芯板面内压缩破坏机制, 利用材料试验机对夹芯板面内压缩性能进行了试验测试, 并开展了模拟研究。结果表明: 夹芯板的面内压缩破坏方式主要有面板折断、夹芯板屈曲失稳和夹芯板中面板与蜂窝芯脱粘3种类型。面板为夹芯板面内压缩的主要承载构件, 蜂窝芯对面板起到固支作用。面板结构参数与材料参数为影响夹芯板面内压缩抗压强度与抗压刚度主要因素, 多数蜂窝芯的结构参数与材料参数对夹芯板面内压缩抗压强度的影响微弱, 而个别蜂窝芯的结构参数对夹芯板面内压缩抗压刚度的影响比较显著。夹芯板体积一定时, 随着蜂窝芯胞体单元数量的增加, 夹芯板面内压缩的抗压强度与抗压刚度逐渐增大。      

水下冲击波作用的铝合金蜂窝夹层板动力学响应研究

为研究铝合金蜂窝夹层板水下爆炸冲击波载荷作用的动态响应及抗冲击性能,利用非药式水下爆炸冲击波加载装置对气背固支5A06铝合金夹层板及具有相同面密度的单层板进行水下冲击波加载试验。利用高速相机结合三维数字散斑技术(DIC)对夹层板后面板动态响应进行实时测量,获得夹层板气背面受水下冲击波作用的动态响应历程及变形毁伤模式,比较分析铝合金蜂窝夹层板抗冲击防护性能。结果表明,较相同面密度的单层板,蜂窝夹层板受水下冲击波载荷作用的芯层压缩能有效减少气背面板的塑性变形,提高夹层结构整体抗冲击性能。     

四边固支对称蜂窝夹层板主共振非线性动力学计算

应用同伦分析方法(HAM)研究了四边固支对称蜂窝夹层板主共振情况下的非线性动力学特性。将铝基蜂窝芯层等效为一正交异性层, 等效弹性参数由修正后的Gibson方程得出。基于经典叠层板理论(CPT)和几何大变形理论建立了四边固支蜂窝夹层板受横向激振力作用下的受迫振动微分方程, 通过振型正交化将蜂窝夹层板受迫振动微分方程简化成双模态下的动力学控制方程, 得到了主共振情况下的平均方程, 研究了不同结构参数对动力学特性的影响。计算结果表明, 蜂窝夹层板的幅频特性曲线类似单自由度Duffing方程响应曲线, 随着结构参数的增大, 硬特性明显加大并且振幅的峰值明显减小, 所得结论可为蜂窝夹层板的设计和实际应用提供理论依据。     

Modelling of aluminium foam core sandwich panels under impact perforation

Aluminium foam core sandwich panels are good energy absorbers for impact protection applications, such as light-weight structural panels, packing materials and energy absorbing devices. In this study, the high-velocity impact perforation of aluminium foam core sandwich structures was analysed. Sandwich panels with 1100 aluminium face-sheets and closed-cell A356 aluminium alloy foam core were modelled by three-dimensional finite element models. The models were validated with experimental tests by comparing numerical and experimental damage modes, output velocity, ballistic limit and absorbed energy. By this model the influence of foam core and face-sheet thicknesses on the behaviour of the sandwich panel under impact perforation was evaluated.     

The influence of core height and face plate thickness on the response of honeycomb sandwich panels subjected to blast loading

This paper reports on an investigation into the behaviour of circular sandwich panels with aluminium honeycomb cores subjected to air blast loading. Explosive tests were performed on sandwich panels consisting of mild steel face plates and aluminium honeycomb cores. The loading was generated by detonating plastic explosives at a pre-determined stand-off distance. Core height and face plate thickness were varied and the results are compared with previous experiments. It was observed that the panels exhibited permanent face plate deflection and tearing, and the honeycomb core exhibited crushing and densification. It was found that increasing the core thickness delayed the onset of core densification and decreased back plate deflection. Increasing the plate thickness was also found to decrease back plate deflection, although the panels then had a substantially higher overall mass.     

Finite element modelling of low velocity impact of composite sandwich panels

This paper outlines a finite element procedure for predicting the behaviour under low velocity impact of sandwich panels consisting of brittle composite skins supported by a ductile core. The modelling of the impact requires a dynamic analysis that can also handle non-linearities caused by large deflections, plastic deformation of the core and in-plane degradation of the composite skins. Metal honeycomb, frequently used as a core material, is anisotropic and requires a non-standard approach in the elasto-plastic part of the analysis. A suitable yield criteria based on experimental observations is proposed. Comparisons of experimental and finite element responses are shown for sandwich panels with carbon fibre skins and aluminium honeycomb cores.     

Some theoretical considerations on the dynamic response of sandwich structures under impulsive loading

A theoretical solution is obtained to predict the dynamic response of peripherally clamped square metallic sandwich panels with either honeycomb core or aluminium foam core under blast loading. In the theoretical analysis, the deformation of sandwich structures is separated into three phases, corresponding to the transfer of impulse to the front face velocity, core crushing and overall structural bending/stretching, respectively. The cellular core is assumed to have a progressive crushing deformation mode in the out-of-plane direction, with a dynamically enhanced plateau stress (for honeycombs). The in-plane strength of the cellular core is assumed unaffected by the out-of-plane compression. By adopting an energy dissipation rate balance approach developed by earlier researchers for monolithic square plates, but incorporating a newly developed yield condition for the sandwich panels in terms of bending moment and membrane force, “upper” and “lower” bounds are obtained for the maximum permanent deflections and response time. Finally, comparative studies are carried out to investigate: (1) influence of the change in the in-plane strength of the core after the out-of-plane compression; (2) performances of a square monolith panel and a square sandwich panel with the same mass per unit area; and (3) analytical models of sandwich beams and circular and square sandwich plates.     

Mechanical response of metallic honeycomb sandwich panel structures to high-intensity dynamic loading

Explosive tests were performed in air to study the dynamic mechanical response of square honeycomb core sandwich panels made from a super-austenitic stainless steel alloy. Tests were conducted at three levels of impulse load on the sandwich panels and solid plates with the same areal density. Impulse was varied by changing the charge weight of the explosive at a constant standoff distance. At the lowest intensity load, significant front face bending and progressive cell wall buckling were observed at the center of the panel closest to the explosion source. Cell wall buckling and core densification increased as the impulse increased. An air blast simulation code was used to determine the blast loads at the front surfaces of the test panels, and these were used as inputs to finite element calculations of the dynamic response of the sandwich structure. Very good agreement was observed between the finite element model predictions of the sandwich panel front and back face displacements and the experimental observations. The model also captured many of the phenomenological details of the core deformation behavior. The honeycomb sandwich panels suffered significantly smaller back face deflections than solid plates of identical mass even though their design was far from optimal for such an application.     

Behaviour of sandwich panels subject to intense air blasts – Part 2: Numerical simulation

Finite element simulation is employed to analyse the behaviour of clamped sandwich panels comprising equal thicknesses mild steel plates sandwiching an aluminium honeycomb core when subject to blast loadings. Pressure-time histories representative of blast loadings are applied to the front plate of the sandwich panel. The FE model is verified using the experimental test results for uniform and localised blast loading in the presence of a honeycomb core and with only an air gap between the sandwich plates. It is observed that for the particular core material, the load transfer to the back plate of the panel depends on the load intensity, core thickness and flexibility of the sandwich panels.     

钢板夹泡沫铝组合板抗爆性能研究

鉴于泡沫铝材料优异的吸能特性和夹层结构在强度、刚度上的优势,提出了分层结构为钢板-泡沫铝芯层-钢板的抗爆组合板。对厚度为10 cm、7 cm和5 cm的组合板进行了5组不同装药量的爆炸试验,考察了各板在不同装药量爆炸条件下的变形及破坏情况,并对变形破坏过程进行了理论分析。研究表明:组合板承受爆炸冲击荷载时,通过局部压缩变形和整体弯曲变形吸收能量。钢板相同时,适当增大泡沫铝芯层厚度,增强面板与芯层间连接,可提高该组合板的抗爆性能,防止组合板发生剥离,减小其承受爆炸冲击荷载时产生的变形。     

碳纤维铝蜂窝夹芯复合结构隔声性能研究

铝蜂窝夹芯复合结构在航空工业、高速列车及汽车车体中得到越来越多的应用,其隔声性能对车内及机舱噪声有重要影响。建立了碳纤维铝蜂窝夹芯复合结构有限单元模型,用有限单元法计算了结构在声载荷激励下的响应,并计算分析了复合结构的隔声性能,分析了碳纤维复合面板厚度、面板层数、铺设角度、铝蜂窝芯层的厚度、铝蜂窝壁厚对隔声性能的影响。研究结果表明,面板采用碳纤维复合结构时,在小于1 000 Hz的低频段,相同面板厚度的铝蜂窝复合结构隔声性能比全铝合金材料的铝蜂窝夹芯复合结构有所降低,而且在高频段会出现隔声量更低的隔声低谷;相较于铝合金面板,复合结构的面板采用碳纤维复合材料时,能够实现整体结构轻量化也提高复合结构的隔声性能;各层之间按相对90°铺设时复合结构隔声性能最好;随着面板厚度的增加复合结构隔声性能增加,面板层总厚度不变的情况下,单层面板或者过多的层数都会使复合结构隔声性能降低。     

Failure analysis of adhesive surface damage in sandwich plates under compressed loads

Abstract

Failures of honeycomb sandwich plates are analyzed using experiments and three-dimensional (3D) finite element simulations to understand the failure mechanism. Meanwhile, correlations of the critical load and various physical parameters (e.g., height and thickness of the core) are investigated. The results demonstrated that the core height and skin thickness have significant effects on the compressed load buckling of the honeycomb sandwich plates, the core density is a sub-critical sensitive factor, while wall thickness and spacing of the cell, and the sandwich modulus have negligible effects. Cracking on the adhesive surface is the dominant factor to reduce the buckling critical load of the laminated plate, which leads to failures of sandwich plates. The ultimate failure of the sandwich panel is attributed to severe deformations that lead to local cracking of the entire cemented adhesive surface. Due to the bonding of the adhesive surface defects, the actual loads related to the core height are large enough to cause compressions with local buckling. Hence, the actual loads cannot reflect the performance of the sandwich panels. It is recommended to use panels with appropriate thicknesses below the sandwich and moderate grid density in the design.     

Impact behavior and energy absorption of paper honeycomb sandwich panels

Dynamic cushioning tests were conducted by free drop and shock absorption principle. The effect of paper honeycomb structure factors on the impact behavior was analyzed. Results of many experiments show that the dynamic impact curve of paper honeycomb sandwich panel is concave and upward; the thickness and length of honeycomb cell-wall have a great effect on its cushioning properties; increasing the relative density of paper honeycomb can improve the energy absorption ability of the sandwich panels; the thickness of paper honeycomb core has an up and down fluctuant effect on the cushioning properties; with the increase of the thickness of paper honeycomb core, the effect dies down; flexible corrugated paperboard as liners can improve the compression resistance and cushioning properties of paper honeycombs. The research results can be used to optimize the structure design of paper honeycomb sandwich panel and material selection for packaging design.     

复合材料蜂窝夹层板结构的多工况优化设计研究

以复合材料蜂窝夹层板结构作为研究对象,建立了多工况优化模型,对众多的材料设计变量进行必要的取舍,通过优化分析确定复合材料蜂窝夹层板面板各分层的厚度以及蜂窝芯层的厚度等,使结构满足相应的频率约束、屈曲约束,以及强度约束、位移约束和尺寸限制等,同时达到结构的重量最轻。采用序列二次规划法对某卫星的承力筒结构进行了优化设计,优化结果表明:在满足其振动特性以及静力学特性的条件下,复合材料蜂窝承力筒的各面板层厚度以及蜂窝芯层的厚度均有所减小,减重效果显著,较好地实现了复合材料蜂窝夹层板结构的多工况优化设计。     

Behaviour of sandwich panels subjected to intense air blast – Part 1: Experiments

Tests that investigate the inelastic response of blast-loaded sandwich structures, comprising mild steel plates and aluminium alloy honeycomb cores, are reported. The “uniform” loading was generated by detonating a disc of explosive and directing the blast through a tube towards the target. Localised blast loading was generated by detonating discs of explosive in very close proximity to the test structure. The sandwich panels responded in a more efficient manner to the uniformly distributed loading, and hence the majority of the paper is concentrated on uniform loading response. The honeycomb sandwich results are compared to test results on structures with air as the core. The failure modes and interaction between the components are discussed. Three phases of interaction are identified for each sandwich structure, based upon deformation, contact, crushing and tearing responses of the sandwich components. The compromise between load transfer through the core and improved energy absorption is discussed.