天然气-氢气-空气混合气的层流燃烧速度测定

在定容燃烧弹内研究了常温常压下天然气-氢气-空气混合气的火焰传播规律，得到了不同掺氢比例（氢气在天然气中的体积掺混比例为0％～100％）和燃空当量比（0．6～1．4）下混合气的层流燃烧速率和马克斯坦长度，通过对马克斯坦长度的测量，分析了拉伸对火焰传播的影响。结果表明，随着天然气中掺氢比例的增加，混合气的燃烧速率呈指数规律增加，马克斯坦长度值减小，火焰的稳定性下降。各掺氢比例下，随当量比的增加，马克斯坦长度值增加，火焰的稳定性增强。通过对试验结果的数据拟合，得到了计算天然气-氢气-空气混合气层流燃烧速率的关系式。     

不同初始压力下掺氢天然气的燃烧特性

在定容燃烧弹内研究了不同初始压力下天然气-氢气-空气混合气的火焰传播规律,得到了不同掺氢比例和初始压力下,不同燃空当量比时混合气的层流燃烧速率,并分析了火焰的稳定性及其影响因素.研究结果表明,随着天然气中掺氢比例的增加,混合气的燃烧速率增加,且增长速率逐渐加快,而马克斯坦长度值则随着掺氢比例的增加而减小,即火焰的稳定性下降.不同初始压力下,随着燃空当量比的增加,马克斯坦长度值在不同掺氢比例下均增加,显示火焰的稳定性增加.无拉伸层流燃烧速率随着初始压力的增加略有减小,且在化学当量比附近,变化的初始压力和掺氢比对无拉伸层流燃烧速率的影响最为明显.     

高温高压下掺氢天然气的燃烧特性

在定容燃烧弹内研究了高温(450,K)、高压(0.75,MPa)条件下天然气-氢气-空气混合气的火焰传播过程,获得了不同掺氢比和不同当量比下掺氢天然气的无拉伸层流燃烧速率,并分析了火焰的稳定性。结果表明,高温高压下随着掺氢比的增加,掺氢天然气的燃烧速率增加,且增长速率逐渐加快;马克斯坦长度则随着掺氢比的增加而减小,即火焰的稳定性下降。随着当量比的增加,无拉伸层流燃烧速率呈现先增大后减小的趋势,且最大无拉伸层流燃烧速率所对应当量比的位置随着掺氢比的提高而向浓混合气移动;马克斯坦长度随当量比的增加而增大,即火焰稳定性随当量比的增加而提高。     

丙烷-空气-稀释气层流燃烧速率测定

利用高速纹影摄像法和球型发展火焰研究了常温常压下丙烷-空气,丙烷-空气-稀释气预混层流燃烧特性,获得了不同稀释系数(0、10%、20%、30%)和燃空当量比(0.6～2.0)下混合气的层流燃烧速率和马克斯坦长度值,分析了拉伸对火焰传播速率的影响.结果表明:丙烷-空气混合气的无拉伸火焰传播速率和无拉伸层流燃烧率在当星比1.1时达到最大值,随当量比的增加,马克斯坦长度值降低,火焰前锋面不稳定性趋势增加.当量比为1.4时,马克斯坦长度值由正值转为负值.丙烷-空气-稀释气混合气随稀释系数的增加,火焰传播速率和层流燃烧速率降低,在当量比小于1.4时,随稀释系数的增加,马克斯坦长度值增加,火焰前锋面的稳定性趋势增加.有无稀释气时无拉伸层流燃烧速率的比值仅与稀释系数有关并成线性关系而与混合气浓度无关.     

初始压力对天然气-氢气-空气混合气火焰传播特性的影响

使用定容燃烧弹研究了不同初始压力下天然气-氢气-空气混合气的火焰传播规律,得到了初始压力、掺氢比和燃空当量比对无拉伸层流燃烧速率、质量燃烧流量的影响,结合高速纹影图片分析了影响火焰稳定性的因素(马克斯坦长度、火焰面两侧密度比和火焰厚度).结果表明,掺氢天然气无拉伸层流燃烧速率以及火焰的不稳定性受掺氢比、初始压力和燃空当量比的综合影响.结合高速纹影图片,得出火焰的稳定性会随初始压力的增加而减小;在相同的燃空当量比和掺氢比下,初始压力对密度比的影响不大,但是对火焰厚度的影响比较明显.     

二甲醚-空气混合气层流燃烧速度的测定

在定容燃烧弹中利用高速纹影摄像法系统地研究了不同燃空当量比和初始压力下二甲醚-空气混合气的层流燃烧特性.利用球形扩散火焰理论分析纹影照片,获得了不同初始压力和当量比下的二甲醚-空气混合气层流燃烧速率.结果表明：随着初始压力的增大,层流燃烧速率显著减小,层流燃烧速率的峰值向浓混合气侧偏移.拉伸层流燃烧速率随拉伸率的增加而增加,拉伸层流质量燃烧速率随拉伸率的增加而减小.根据球形扩散火焰模型得到混合气的马克斯坦长度值表明：在各初始压力下,随着当量比的增加,二甲醚-空气混合气的马克斯坦长度值逐渐减小,火焰前锋面的不稳定性增加.     

EGR中二氧化碳对氢气层流燃烧特性的影响

为了更深入地理解废气中二氧化碳对掺氢燃料燃烧特性的影响,在定容燃烧弹中利用高速摄像系统研究了不同燃空当量比φ(0.6～1.4)和稀释比(0%～40%)下CO2稀释氢气-空气混合气的层流燃烧特性.结果表明:氢气-空气混合气的火焰传播速率随着燃空当量比的增大而增大;马克斯坦长度随着当量比的增大而增大,即火焰的稳定性增强;随稀释比的增大,无拉伸火焰传播速率S1明显减小;同时得到层流火焰燃烧速率,并分析了稀释比对火焰稳定性的影响.通过对试验结果数据拟合,获得了计算氢气-CO2-空气混合气的无拉伸层流燃烧速率的拟合多项式.     

天然气/氢气燃烧特性研究

在定容燃烧弹中研究了不同氢气掺混比例、燃空当量比和初始压力下的大然气／氢气混合气的燃烧特性，建立了适合用于容弹计算的准维双区模型。研究结果表明：在各种当量比和初始压力下，随着掺氢比例的增加，混合气的质量燃烧速率明显增加，燃烧持续期和火焰发展期娃著缩短。随着掺氢比例的增加，短的燃烧持续期所对应的当量比范围变宽，稀混合气和浓混合气条件下天然气掺氢对火焰发展期缩短的效果更明显。化学计量比附近（1．0—1．1）掺氢燃烧对燃烧最大压力值影响不大，浓混合气（燃空当量比大于1．1）和稀混合气燃烧时，随着掺氢比例的增加，最大燃烧压力值增加。     

高温高压下二甲醚—空气预混层流燃烧特性研究

在定容燃烧弹内研究了初始压力为0.5 MPa时,不同初始温度和燃空当量比下二甲醚-空气混合气预混层流火焰的层流燃烧速率和马克斯坦长度,分析了火焰拉伸对火焰传播速率的影响.基于容弹燃烧的双区模型计算了预混层流燃烧的燃烧特性参数.结果表明:随着初始温度的增加,二甲醚-空气预混合气的无拉伸火焰传播速率和无拉伸层流燃烧率增加;对于给定的初始温度,在化学当量比偏浓混合气一侧存在一个层流燃烧速度的峰值;随初始温度和当最比增加,马克斯坦长度值减小,火焰前锋面的不稳定性增加;最大燃烧压力随初始温度的增加而下降,压力升高率随初始温度的增加而降低.     

CO_2稀释对天然气掺氢预混层流火焰燃烧特性的影响

在定容燃烧弹内研究了相同的掺氢比、不同的二氧化碳体积分数下,天然气-氢气-二氧化碳-空气的预混气体层流火焰燃烧特性;分析了二氧化碳体积的增加对火焰燃烧特性的影响.结果表明:随着二氧化碳体积分数的增加,二氧化碳气体的稀释作用和吸热作用使混合气燃烧速率降低,火焰半径随时间的增长率明显减小;同时火焰前锋出现"ω"形的火焰锋面,减小了已燃区和未燃区接触面积,拉伸火焰传播速率明显下降.当二氧化碳体积分数?CO_2≤5%,时,拉伸火焰传播速率随拉伸率的增加而减小,马克斯坦长度为正值,火焰前锋面趋于稳定;当?CO_2≥10%,时,马克斯坦长度随二氧化碳体积分数的增加没有统一的规律可循,由于氢气和天然气的马克斯坦长度随着稀释度的增加有相反的变化规律,所以其变化规律取决于可燃混合气中占主导地位的可燃气体是氢气还是天然气.     

Measurement of laminar burning velocities and Markstein lengths of diluted hydrogen-enriched natural gas

The laminar flame characteristics of natural gas–hydrogen–air–diluent gas (nitrogen/CO₂) mixtures were studied in a constant volume combustion bomb at various diluent ratios, hydrogen fractions and equivalence ratios. Both unstretched laminar burning velocity and Markstein length were obtained. The results showed that hydrogen fraction, diluent ratio and equivalence ratio have combined influence on laminar burning velocity and flame instability. The unstretched laminar burning velocity is reduced at a rate that is increased with the increase of the diluent ratio. The reduction effect of CO₂ diluent gas is stronger than that of nitrogen diluent gas. Hydrogen-enriched natural gas with high hydrogen fraction can tolerate more diluent gas than that with low hydrogen fraction. Markstein length can either increase or decrease with the increase of the diluent ratio, depending on the hydrogen fraction of the fuel.     

Effect of initial pressure on laminar combustion characteristics of hydrogen enriched natural gas

Flame propagation of premixed natural gas–hydrogen–air mixtures was studied in a constant volume combustion bomb. Laminar burning velocities and mass burning fluxes were obtained under various hydrogen fractions and equivalence ratios with various initial pressures, while flame stability and their influencing factors (Markstein length, density ratio and flame thickness) were obtained by analyzing the flame images at various hydrogen fractions, initial pressures and equivalence ratios. The results show that hydrogen fraction, initial pressure as well as equivalence ratio have combined influence on both unstretched laminar burning velocity and flame instability. Meanwhile, according to flame propagation pictures taken by the high speed camera, flame stability decreases with the increase of initial pressures; for given equivalence ratio and hydrogen fraction, flame thickness is more sensitive to the variation of the initial pressure than to that of the density ratio.     

Experimental determination of laminar burning velocities and Markstein lengths for 75% hydrous-ethanol, hydrogen and air gaseous mixtures

Hydrogen-rich mixtures generated by the on-board reforming of biomass-derived hydrous-ethanol can be used as a potential alternative fuel (i.e., reformed ethanol fuel, RE fuel). In this paper, outwardly propagating spherical flames were employed to observe the laminar flame characteristics of the gaseous mixtures composed of simulated RE fuel (mixture of 75% hydrous-ethanol and hydrogen) and air in a constant-volume combustion vessel at an initial temperature of 383 K, a pressure of 0.1 MPa, a hydrogen fraction from 0% to 80%, and an equivalence ratio from 0.6 to 1.6. The results show that the unstretched flame propagation speeds and burning velocities increase with increasing hydrogen fraction, especially when the fraction is above 40%. When the hydrogen fraction is less than 40%, the Markstein length and flame instability decrease and increase with the equivalence ratio, respectively, while the reverse holds when the hydrogen fraction is greater than 40%. At an equivalence ratio below 1.4, the Markstein length decreases with increasing hydrogen fraction, indicating a positive correlation between the flame instability and hydrogen fraction. At an equivalence ratio above 1.4, a negative relationship is observed. Finally, it is concluded that a hydrogen fraction of approximately 40% in simulated RE fuel is feasible for spark ignition engines by comparing the laminar burning characteristics of ethanol-air mixtures.     

Laminar burning velocity and Markstein length of nitrogen diluted natural gas/hydrogen/air mixtures at normal,reduced and elevated pressures

Flame propagation of premixed nitrogen diluted natural gas/hydrogen/air mixtures was studied in a constant volume combustion bomb under various initial pressures. Laminar burning velocities and Markstein lengths were obtained for the diluted stoichiometric fuel/air mixtures with different hydrogen fractions and diluent ratios under various initial pressures. The results showed that both unstretched flame speed and unstretched burning velocity are reduced with the increase in initial pressure (except when the hydrogen fraction is 80%) as well as diluent ratio. The velocity reduction rate due to diluent addition is determined mainly by hydrogen fraction and diluent ratio, and the effect of initial pressure is negligible. Flame stability was studied by analyzing Markstein length. It was found that the increase of initial pressure and hydrogen fraction decreases flame stability and the flame tends to be more stable with the addition of diluent gas. Generally speaking, Markstein length of a fuel with low hydrogen fraction is more sensitive to the change of initial pressure than that of a one with high hydrogen fraction.     

Experimental and numerical study on laminar burning characteristics of premixed methane–hydrogen–air flames

An experimental and numerical study on laminar burning characteristics of the premixed methane–hydrogen–air flames was conducted at room temperature and atmospheric pressure. The unstretched laminar burning velocity and the Markstein length were obtained over a wide range of equivalence ratios and hydrogen fractions. Moreover, for further understanding of the effect of hydrogen addition on the laminar burning velocity, the sensitivity analysis and flame structure were performed. The results show that the unstretched laminar burning velocity is increased, and the peak value of the unstretched laminar burning velocity shifts to the richer mixture side with the increase of hydrogen fraction. Three regimes are identified depending on the hydrogen fraction in the fuel blend. They are: the methane-dominated combustion regime where hydrogen fraction is less than 60%; the transition regime where hydrogen fraction is between 60% and 80%; and the methane-inhibited hydrogen combustion regime where hydrogen fraction is larger than 80%. In both the methane-dominated combustion regime and the methane-inhibited hydrogen combustion regime, the laminar burning velocity increases linearly with the increase of hydrogen fraction. However, in the transition regime, the laminar burning velocity increases exponentially with the increase of hydrogen fraction in the fuel blends. The Markstein length is increased with the increase of equivalence ratio and is decreased with the increase of hydrogen fraction. Enhancement of chemical reaction with hydrogen addition is regarded as the increase of H, O and OH radical mole fractions in the flame. Strong correlation is found between the burning velocity and the maximum radical concentrations of H and OH in the reaction zone of the premixed flames.     

Effects of initial pressure and hydrogen concentration on laminar combustion characteristics of diluted natural gas–hydrogen–air mixture

In this study, the experiment study about the laminar burning velocity and the flame stability of CO₂ diluted natural gas–hydrogen–air mixture was conducted in a constant volume combustion vessel by using the high-speed schlieren photography system. The unstretched laminar burning velocity and the Markstein length at different hydrogen fractions, dilution ratios and equivalence ratios and with different initial pressures were obtained. The flame stability was studied by analyzing the Markstein length, the flame thickness, the density ratio and the flame propagation schlieren photos. The results showed that the unstretched laminar burning velocity would be reduced with the increase of the initial pressure and dilution ratio and would be increased with the increase of the hydrogen fraction of the mixture. Meanwhile, the Markstein length would be increased with the increase of the equivalence ratio and the dilution ratio. Slight flaws occurred at the early stage. At a specific equivalence ratio, a higher initial pressure and hydrogen fraction would cause incomplete combustion.     

Effect of initial pressure,temperature and equivalence ratios on laminar combustion characteristics of hydrogen enriched natural gas

In this study, the flame propagation characteristics of premixed natural gas–hydrogen–air mixtures were studied in constant volume combustion bomb by using the high-speed schlieren photography system. The flame radius, laminar flame propagation speed and the flame stretch rate were obtained under different initial pressure, temperature, equivalence ratios and hydrogen fractions. Meanwhile, the flame stability and their influencing factors were obtained by analyzing the Markstein length and the flame propagation schlieren photos under various combustion conditions. The results show that the stretched laminar propagation speed increases with the increase of the initial temperature and hydrogen fraction of the mixture, and will decreases with the increase of the initial pressure. Meanwhile, according to the Markstein length and the flame propagation pictures, the flame stability decreases with the increase of the temperature and hydrogen fraction, and the slight flaws occurred at the early stage; at larger flame radius, the flame stability is more sensitive to the variation of the initial temperature and hydrogen fraction than to that of initial pressure and equivalence ratio.