Synthesis and characterisation of PP-g-butyl acrylate copolymers

Butyl acrylate was grafted onto isotactic polypropylene using benzoyl peroxide as an initiator and toluene as a solvent. Effects of various parameters such as monomer and initiator concentration, reaction time and temperature on rates of polymerization, percentage grafting and grafting efficiency were studied. The extent of grafting achieved was 2.85%. The graft copolymers were characterized by IR, thermal, viscometric and contact-angle studies. Improved thermal stability and decreased intrinsic viscosity and critical surface tension were observed for graft copolymers.     

Preparation and characterization of polyaniline N‐grafted with poly(ethyl acrylate) synthesized via atom transfer radical polymerization

Polyaniline (PANI) N‐grafted with poly(ethyl acrylate) (PEA) was synthesized by the grafting of bromo‐terminated poly (ethyl acrylate) (PEA‐Br) onto the leucoemeraldine form of PANI. PEA‐Br was synthesized by the atom transfer radical polymerization of ethyl acrylate in the presence of methyl‐2‐bromopropionate and copper(I) chloride/bipyridine as the initiator and catalyst systems, respectively. The leucoemeraldine form of PANI was deprotonated by butyl lithium and then reacted with PEA‐Br to prepare PEA‐g‐PANI graft copolymers containing different amounts of PEA via an N‐grafting reaction. The graft copolymers were characterized by Fourier transform infrared spectroscopy, elemental analysis, and thermogravimetric analysis. Solubility testing showed that the solubility of PANI in chloroform was increased by the grafting of PEA onto PANI. The morphology of the PEA‐g‐PANI graft copolymer films was observed by scanning electron microscopy to be homogeneous. The electrical conductivity of the graft copolymers was measured by the four‐probe method. The results show that the conductivity of the PANI decreased significantly with increasing grafting density of PEA onto the PANI backbone up to 7 wt % and then remained almost constant with further increases in the grafting percentage of PEA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Graft copolymerization of methyl acrylate onto poly(vinyl alcohol) initiated by potassium diperiodatonickelate(IV)

The graft copolymerization of methyl acrylate onto poly(vinyl alcohol) (PVA) with a potassium diperiodatonickelate(IV) [Ni(IV)]–PVA redox system as an initiator was investigated in an alkaline medium. The grafting parameters were determined as functions of the temperature and the concentrations of the monomer and initiator. The structures of the graft copolymers were confirmed by Fourier transform infrared spectroscopy, scanning electron microscopy, X‐ray diffraction, differential scanning calorimetry, and thermogravimetric analysis. The Ni(IV)–PVA system was found to be an efficient redox initiator for this graft copolymerization. A single‐electron‐transfer mechanism was proposed for the formation of radicals and the initiation. Other acrylate monomers, such as methyl methacrylate, ethyl acrylate, n‐butyl acrylate, and n‐butyl methacrylate, were used as reductants for graft copolymerization. These reactions definitely occurred to some degree. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 529–534, 2003     

Synthesis and characterization of vegetable tannin-vinyl graft copolymers part I. Cutch-poly(methyl acrylate) graft copolymers

New graft copolymers were synthesized by grafting methyl acrylate onto cutch, a vegetable tanning agent, in acetic acid medium with hydrogen peroxide as the initiator. The graft copolymers were characterized by infrared spectroscopy and thermogravimetric analysis. The dependence of the percentage of grafting, monomer conversion, efficiency of grafting and rate of grafting on the concentrations of initiator, acetic acid, and cutch were investigated. The optimum experimental conditions for grafting were obtained. A probable mechanism of grafting was also proposed.     

Grafting of butyl acrylate onto gelatin in a water-isopropanol medium

Graft copolymerization of butyl acrylate onto gelatin using potassium persulphate initiator was studied in a water-isopropanol medium. The crude graft copolymers were soxhlet extracted with acetone to remove the loosely bound ungrafted homopolymer. The influence of a number of experimental factors such as effect of time, monomer concentration, initiator concentration, backbone concentration and temperature on the graft copolymerization of gelatin were investigated.     

Grafting of ethyl acrylate onto monofilament polyester fibers using benzoyl peroxide

Ethyl acrylate was grafted onto monofilament poly(ethylene terephthalate) fibers using benzoyl peroxide as a chemical initiator. Breaking tenacity and densities of grafted fibers decreased while breaking elongation increased with the graft yield. Scanning electron micrographs showed that the fiber geometry and its diameter were not affected by grafting. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 1701–1705, 1998     

以聚乙烯醇为保护胶体的乳液与部分官能团的接枝反应研究

主要研究了在以聚乙烯醇为保护胶体的醋酸乙烯乳液聚合中,乳液与环氧丙烯酸酯、聚氨酯、硅烷等官能团的接枝反应.在以过硫酸铵为引发剂、以聚乙烯醇为保护胶体的醋酸乙烯乳液聚合中,乳液与上述各类官能团间发生的接枝反应直接影响乳液的黏度、固体含量、剪切强度等宏观性质.研究发现官能单体脂肪醇聚氧乙烯醚、丙烯酸异辛酯(2-EHA)等单体和丙烯酸(AA)与乙烯基三乙氧基硅烷共同作用时对乳液的宏观性质影响显著.     

Glycidyl methacrylate–grafted linear low‐density polyethylene fabrication and application for polyester/polyethylene bonding

The grafting of glycidyl methacrylate (GMA) onto linear low‐density polyethylene (LLDPE) was investigated. The grafting was performed by free‐radical grafting in the melt state in a twin‐screw extruder using an organic peroxide as initiator. The effect of initial GMA and peroxide concentration, styrene comonomer addition, as well as initial resin viscosity, on the final content in grafted moieties, unbound homopolymer, and unreacted monomer was assessed. The effect of process parameters such as flow rate, screw rotation speed, and barrel temperature was also investigated. Chemical composition was shown to be the main parameter for controlling grafting level and grafting efficiency. Grafting levels up to 1.8% and efficiency of 90% were reported even though in most conditions, the graft efficiency was severely decreased by the homopolymerization of GMA into polyGMA chains not bound to LLDPE. Finally, the effect of grafting level and the presence of unbound GMA‐based species on the efficiency GMA‐grafted LLDPE as adhesive between polyethylene and polyester were discussed. Good adhesion to poly(ethylene terephthalate) copolymer was found for low viscosity grafted polyethylene resins. A significant improvement in adhesive strength on polyester was observed when the molecular weight of the grafted LLDPE was increased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3180–3191, 2004     

Graft copolymerization of butyl acrylate onto pullulan using manganic pyrophosphate as initiator

The graft copolymerization of butyl acrylate onto pullulan using manganic pyrophosphate as initiator in aqueous medium was studied. The effects of concentration of initiator, monomer, pullulan, and sulfuric acid on the percentage of grafting, the grafting, efficiency, as well as the rate of graft copolymerization were investigated. The rate equation was derived and a suitable reaction mechanism was proposed. Finally, the grafted samples were characterized by IR spectral measurement.     

Graft copolymerization of methyl acrylate onto poly(vinyl alcohol) initiated by potassium diperiodatoargentate(III)

The graft copolymerization of methyl acrylate onto poly(vinyl alcohol) (PVA) using potassium diperiodatoargentate(III) [Ag(III)]–PVA redox system as initiator was studied in an alkaline medium. Some structural features and properties of the graft copolymer were confirmed by Fourier‐transfer infrared spectroscopy, scanning electron microscope, X‐ray diffraction and thermogravimetric analysis. The grafting parameters were determined as a function of concentrations of monomer, initiator, macromolecular backbone (X?_n = 1750, M? = 80 000 g mol^?1), reaction temperature and reaction time. A mechanism based on two single‐electron transfer steps is proposed to explain the formation of radicals and the initiation profile. Other acrylate monomers, such as methyl methacrylate, ethyl acrylate and n‐butyl acrylate, were also used to produce graft copolymerizations. It has been confirmed that grafting occurred to some degree. Thermogravimetric analysis was performed in a study of the moisture resistance of the graft copolymer. Copyright © 2004 Society of Chemical Industry     

Grafting of styrene onto poly(butyl acrylate) in emulsion

The effect of time, temperature, the concentration of initiator and emulsifier, and the ratio of starting polymer to monomer on the degree of conversion (MC) of styrene and the grafting efficiency (GE) of polystyrene has been investigated. The reaction was initiated with potassium persulphate. It has been found that the degree of conversion of styrene and the grafting efficiency change in opposite directions when plotted as functions of the reaction parameters studied. The graft copolymerization is assisted by short reaction times and weight ratios of poly(butyl acrylate) to styrene greater than unity. The results obtained suggest that higher grafting efficiencies are obtained when the concentration of emulsifier is below its c.m.c. (critical micellar concentration) value. When using two different anionic emulsifiers it has been observed that the effect of initiator concentration on the degree of conversion of styrene and the grafting efficiency is complicated. Both the quantities studied (MC and GE) exhibit extrema in the range of initiator concentration studied (3.7?33.3 × 10^?5 mol dm^?3 of H₂O). No meaningful effect of temperature in the range 60°–90°C or that of dodecyl mercaptan (molecular weight regulator) used in an amount 0–0.4% in relation to poly(butyl acrylate) and styrene has been observed on the MC and GE values.     

Ni(Ⅳ)引发丙烯酸甲酯与三元尼龙接枝共聚反应的研究

以二过碘酸合镍(Ⅳ)钾〔Ni(Ⅳ)〕为氧化剂,共聚尼龙上的弱的还原基团(酰胺基)为还原剂,组成氧化还原引发体系,于碱性介质中直接在共聚尼龙分子骨架上产生接枝点,引发丙烯酸甲酯(MA)的接枝共聚合反应,获得了较高的接枝效率(可达90%以上)。探讨了引发剂浓度、单体浓度、反应温度对接枝参数的影响,结果表明:当c〔Ni(Ⅳ)〕=8×10-4mol/L,c(MA)=1 5mol/L,θ=35℃时,接枝效率和接枝百分比可达到最高值。用红外光谱、X射线衍射、扫描电镜对接枝共聚物进行了表征,提出了建立在镍(Ⅳ)还原为镍(Ⅱ)的过程为两步单电子转移的基础之上的引发机理。将所得接枝共聚物用作尼龙/聚甲基丙烯酸甲酯体系的增容剂,通过扫描电镜分析表明:该共混体系的相容性得到一定程度的改善。     

Poly(ethylene glycol)-block-poly(butyl acrylate). I. Synthesis

Prepolymers of poly(ethylene oxide) (Pre-PEO) were synthesized by reacting azoisobutyronitrile (AIBN) with poly(ethylene glycol) (PEG), and their structures were characterized by IR and UV. The molecular weight of pre-PEO was related to the feed ratio and reaction time. These prepolymers can be used to prepare block copolymers—poly(ethylene oxide)-block-poly(butyl acrylate) (PEO-b-PBA) by radical polymerization in the presence of butyl acrylate (BA). Solution polymerization was a suitable technique for this step. The yield and the molecular weight of the product were related to the ratio of the prepolymer to BA, the reaction time, and temperature. GPC showed that the molecular weight increased with a higher ratio of BA to pre-PEO. The intrinsic viscosity of the copolymers was only slightly dependent on reaction time, but decreased at higher reaction temperatures, as did the amount of PBA homopolymer. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65:1667–1674, 1997     

Grafting of maleic anhydride onto polypropylene: Synthesis and characterization

Isotactic polypropylene was grafted with maleic anhydride using benzoyl peroxide as an initiator and toluene as a solvent. Effects of various parameters such as monomer and initiator concentration, reaction time, and reaction temperature on percentage grafting were studied. Effect of various solvents on extent of grafting was also studied. The maximum extent of grafting achieved was 5.3%. The graft copolymers were characterized by i.r., thermal, viscometric, and contact angle studies. Improved thermal stability and decreased intrinsic viscosity and critical surface tension were observed for graft copolymers. © 1994 John Wiley & Sons, Inc.     

丙烯酸丁酯改性C_9石油树脂的研究

利用丙烯酸丁酯改性C9石油树脂,以AIBN为引发剂,以正庚烷为溶剂,采用自由基溶液聚合法合成了C9石油树脂/丙烯酸丁酯接枝共聚物。采用单因素实验和正交实验,考察了反应中单体的选择、单体用量、引发剂用量、反应温度、反应时间对接枝率以及单体转化率的影响。最佳反应条件为:反应温度为80℃,反应时间为4 h,引发剂用量为0.75 g,丙烯酸丁酯的用量为12%,在此条件下,产物的接枝率为27.03%。红外光谱分析证实了接枝产物的生成。     

Swelling behavior of gelatin‐g‐poly(butyl acrylate) copolymers

Gelatin‐g‐poly (butyl acrylate) copolymers were prepared with gelatin and butyl acrylate. The effects of various reaction parameters, including the concentration of the monomer, the concentration of the initiator, the concentration of gelatin, the reaction time, and the temperature, on the swelling behavior were studied systematically. In addition, the effect of the intercalation of graft copolymers with montmorillonite on the swelling behavior was investigated. The results indicated that the graft copolymerization and intercalation with montmorillonite could greatly reduce the swelling degree of gelatin. The swelling process of the copolymers followed second‐order kinetics identical to those of the original gelatin. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1033–1037, 2005     

Optimized condition for grafting reaction of poly(butyl acrylate) onto oil palm empty fruit bunch fibre

Preparation of poly(butyl acrylate)‐grafted oil palm empty fruit bunch fibre (OPEFB) has been successfully carried out using H₂O₂/Fe²⁺ as a redox initiator in aqueous solution. The effects of reaction temperature and period, as well as the amount of monomer, initiator and nitric acid, on the percentage of grafting were investigated. The percentage of grafting increases with amount of monomer and can be controlled by setting the appropriate reaction conditions. The maximum percentage of grafting (about 265%) was obtained when the reaction was carried out without acid under optimum conditions (reaction period: 2 h, reaction temperature: 55 °C, amount of H₂O₂: 5.88 mmol) with 42.2 mmol of monomer. Mechanisms of grafting of butyl acrylate onto OPEFB were proposed. Characterization of the grafted OPEFB was done by Fourier‐transform infrared spectroscopy and scanning electron microscopy. The thermal properties were studied by thermogravimetric analysis. Copyright © 2003 Society of Chemical Industry     

The study of melt grafting mechanism of acrylic acid and butyl acrylate onto low density polyethylene and its application as internal plasticizer

Melt grafting of acrylic acid (AA) and butyl acrylate (BA) (equal molar ratios) onto low‐density polyethylene (LDPE) was carried out in Haake internal mixter by free radical grafting copolymerization. The graft degree of AA and BA in the grafted LDPE (LDPE‐g‐(AA+BA)) was determined by FTIR. The influences of initiator on the graft degree of AA and BA, melt flow rate (MFR), and gel content were investigated, and the optimum conditions were obtained. The successive self‐nucleation/annealing (SSA) thermal fraction method was used to characterize the molecular structure and polydispersity of LDPE‐g‐(AA+BA) with various graft degrees. The effects of thermal fraction parameters on fraction of LDPE‐g‐(AA+BA) were investigated. On the basis of the results of SSA, the grafting reaction mechanism of AA and BA onto LDPE was proposed, i.e., grafting reaction preferentially occurred on the tertiary carbons of LDPE. The grafted LDPE possessed suitable reactivity and rheological property. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

聚丙烯固相接枝苯乙烯和丙烯酸乙酯的研究

用固相接枝共聚方法制备聚丙烯（PP）接枝聚苯乙烯（PP-g-PS)和聚丙烯接枝聚丙烯酸乙酯（PP-g-PEA)，考察了引发剂浓度、反应温度、反应时间与单体种类对接枝反应的影响，对接枝改性的PP进行结构和热分析表征，并用接枝功能化的聚丙烯做增容剂，研究了其对纳米SiO2/PP复合材料力学性能的影响。力学性能研究表明：低含量接枝聚丙烯的存在可使SiO2/PP复合材料的韧性大幅提高。     

Chlorohydrin water swellable rubber compatibilized by an amphiphilic graft copolymer. I. Synthesis and characterization of compatibilizer PVA‐g‐PBA

The graft copolymerization of butyl acrylate onto poly(vinyl alcohol) with ceric ammonium nitrate as redox initiator in a aqueous medium has been investigated. The formation of graft copolymer was confirmed by means of IR, scanning electron microscopy (SEM), and wide‐angle X‐ray diffraction (WAXD). The percentage of mononer conversion and percentage of grafting varied with concentrations of initiator, nitric acid, monomer, macromolecular backbone (X_n = 1750, M = 80 000), reaction temperature and reaction time. Some inorganic salts and organic solvents have a great influence upon grafting. The reaction mechanism has been explored, and rate equations for the reaction are established. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 977–986, 2000