共查询到19条相似文献,搜索用时 465 毫秒
1.
深圳卓越·皇岗世纪中心项目二号塔楼建筑物主体高度238m,核心筒部分及屋顶钢架高度升至260m,核心筒高宽比为17.3,属超B级高层建筑。针对本工程的具体特点,文章着重论述了结构设计的策略。对结构荷载取值和地震作用取值、自振特性、风和地震作用下的计算结果等内容进行了介绍,对于结构设计中的几个特殊问题和动力弹塑性分析等方面进行较为深入的探讨。通过对计算结果的分析比较,结构设计成功解决了结构超限问题。本文的有关方法和结论可为相关工程提供参考。 相似文献
2.
厦门市海峡交流中心二期2号塔楼建筑物主体高度215m,高宽比为4.8,属超B级高层建筑,采用了钢管混凝土框架-核心筒结构体系。本文对该工程的结构荷载取值和地震作用取值、自振特性、风和地震作用下的计算结果等内容进行了介绍,并且对中震不屈服分析和动力弹塑性分析等方面也进行了较为深入的探讨。通过对计算结果的分析比较,证明结构设计成功解决了结构超限问题,结构设计是安全可靠的。文章最后介绍了针对本塔楼进行的新型钢管混凝土梁柱节点试验研究成果。本文的有关方法和结论可为相关工程提供参考。 相似文献
3.
4.
江苏昆山中城国际公寓是一幢室外地坪至建筑大屋面为159.75m,大屋面以上的核心筒至室外地坪总高度173.6m的超高层建筑。选择了框架-钢筋混凝土核心筒结构,针对结构的荷载和地震作用取值,风和地震作用下的计算结构比较,规范验算等内容进行了介绍,并且对结构设计中的转换层的处理以及弹塑性的分析等方面进行了深入的探讨。 相似文献
5.
6.
环贸中心项目位于深圳市前海自贸区,其中T1、T2塔楼结构高度分别为249.5 m和239.0 m,采用了框架–核心筒结构体系,在上部局部收进为框架–剪力墙结构.结构存在高度超高、立面收进、扭转不规则、连体、构件间断、承载力突变和斜墙转换等超限内容,分别采用YJK和ETABS软件对结构进行多遇地震下和设防地震下的可行性分析、楼板应力分析、悬挑及连体结构分析、舒适度分析和跨层柱屈曲分析,采用SAUSAGE软件进行了结构动力弹塑性分析、弹塑性楼板应力分析,采用ABAQUS软件进行转换结构、钢梁开洞、复杂节点分析等结构专项研究.通过对计算结果的分析比较,证明结构设计成功解决了结构超限问题,结构设计是安全可靠的,可为相关工程提供参考. 相似文献
7.
招商城市主场工程位于深圳市福田区,地面以上主楼33层,地面以下2层,建筑总高度为99.7m。结构平面和竖向均不规则,属超限结构。采用ETABS和SATWE对结构进行了整体分析,两者的计算结果吻合较好,且满足规范的相关要求,并采用有限元软件ABAQUS对受力关键的型钢混凝土柱进行了有限元分析,分析结果表明,型钢混凝土柱中型钢和混凝土的应力均在规范限值以内。介绍了对结构荷载取值和地震作用取值、自振特性、风荷载和地震作用下的计算结果等内容,并介绍了针对工程的具体特点采取的抗震措施。计算和分析结果表明,结构设计解决了超限问题,结构设计安全可靠,可为相关工程提供参考。 相似文献
8.
9.
10.
11.
12.
13.
14.
河南省广播电视发射塔设计总高度为388.0m,作为超高结构,其难点在于塔身外围桉叶糖形钢柱的吊装,方案设计分别从超高塔结构施工时垂直运输机械的选择、布置方式、塔式起重机基础、塔式起重机安装和拆除几个方面进行分析,最终采用一台ZSC 50180平臂式塔式起重机作为桉叶糖形钢柱主要吊装工具,布置方式为井道内附着式,同时塔楼顶部安设一台SCM-D300动臂塔式起重机,作为桅杆天线的吊装以及ZSC50180的拆除,满足了吊装需要,为工程顺利进行起到了关键作用。 相似文献
15.
Joachim Dehm Dipl.‐Ing. 《Stahlbau》2007,76(4):213-221
160 m self‐supporting lattice tower for a Wind Energy Conversion System. The highest wind energy system in the world. The highest wind energy conversion system of the world have been erected in Laasow near (by) Cottbus. The height of the tower is 160 m, and the height of the whole system up to the tips of the rotor blades is 205 m. The self‐supporting lattice tower from SeeBa supports a turbine EL2500 produced by Fuhrländer. The estimated output of about 7 million kWh corresponds to the consumption of about 1800 4‐person households. The advanced height of the structure represents a major challenge to static and design engineers, to suppliers and to the erection staff. This paper will give a short summary of the requirements concerning the static analysis for this tower. The differences between the present lattice tower and the normally used tubular steel towers will also be pointed out. 相似文献
16.
17.
18.
The steel–concrete hybrid wind turbine tower is characterized by the lower part of the traditional steel tubular tower replaced with the concrete segment. The lateral stiffness will be improved obviously, and then, the excessive vibration of the steel tower can be solved effectively. Based on the improved genetic algorithm, an optimization program is built to consider the influence of materials, labor, machinery, and transportation on the construction cost of a steel–concrete hybrid tower for a 2.0‐MW wind turbine with a hub height of 120 m, in which the initial height of the concrete segment is 32 m. During the optimization process, design requirements of relevant specifications and industry standards are used as the constraints. The optimization variables include the bottom and top diameters of the tower, the wall thickness of each segment, the height of the concrete segment, and the area of the prestressed steel strand. By comparing the results of construction cost and structural capacity before and after optimization, it can be found that the steel–concrete hybrid wind turbine tower after optimization has the better structural stiffness and lower construction cost. The proposed optimization program can meet the design requirements and significantly improve the economic performance of the tower. 相似文献