La^3掺杂对纳米TiO2微观结构及光催化性能的影响

以钛酸丁酯和氧化镧为原料，采用溶胶－凝胶法制备了La^3掺杂TiO2纳米粉体，讨论了不同掺杂浓度，不同热处理温度的样品催化降解刚果红染料实验中的光催化活性，并通过X射线衍射（XRD）、透射电镜（TEM）分析了La^3掺杂TiO2样品的相组成、晶胞参数和晶粒大小对光催化活性的影响。结果表明La^3掺杂能够显著提高TiO2粒子的光催化活性，最佳掺杂浓度为100：3．0，最佳热温度为600℃；La^3掺杂的TiO2的相组成是影响光催化活性的决定性因素，晶格膨胀程度及晶粒大小对光催化活性的影响，主要是在相组成相或相近时才体现得比较明显。     

La3+离子掺杂对纳米ZnO光催化性能的影响

采用共沉淀法,选择尿素为沉淀剂,制备了一系列不同La3 掺杂浓度的纳米ZnO粉体.讨论了不同掺杂浓度的样品催化降解甲基橙的光催化活性,并通过X射线衍射(XRD)和透射电镜(TEM)等分析测试手段研究了粉体样品的相组成、晶胞参数和晶粒大小对光催化性能的影响.结果表明:La3 掺杂能够显著提高ZnO粒子的光催化活性.最佳掺杂浓度为100:0.2;最后提出了La3 改善纳米ZnO粉体光催化性能的作用机制.     

Ce-TiO2光催化剂的制备与性能研究

采用溶胶-凝胶法制备了稀土Ce离子掺杂的纳米TiO2光催化剂(Ce-TiO2),通过XRD、FT-IR、UV-Vis、PL、Nano-sizer纳米粒度分析仪等对Ce-TiO2样品进行了表征和分析,并以亚甲基蓝(MB)作为目标降解物,考察了不同掺杂浓度及经不同温度热处理后的Ce-TiO2样品对MB的光催化降解效果,结果表明所制备样品的晶型均为锐钛矿相和金红石相的混晶相,Ce离子的掺杂拓展了TiO2在可见光区的光谱响应范围,提高了TiO2光催化活性。当pH值为1.5,Ce的掺杂量为n(Ce)∶n(TiO2)=1∶300,热处理温度为600℃条件下制备的样品其催化活性显著高于Degussa P25。     

镧掺杂纳米二氧化钛光催化剂的制备及性能研究

采用溶胶-凝胶法制备了稀土La离子掺杂的纳米TiO2光催化剂(La-TiO2),通过XRD、PL、UV-Vis对La-TiO2样品进行了表征和分析,并以亚甲基蓝(MB)作为目标降解物,研究了不同热处理温度及不同La掺杂浓度的(La-TiO2)样品对MB的光催化降解效果。结果表明,所制备样品的晶型均为锐钛矿相和金红石相的混晶相,La离子的掺入拓展了TiO2对可见光的吸收范围,有效地抑制了光生电子-空穴对的复合,提高了TiO2的光催化性能。La的掺杂量为n(La)∶n(TiO2)=1∶200,热处理温度为600℃条件下制备的样品对亚甲基蓝的降解率为96.6%,显著高于Degussa P25(58.62%)。     

磁性La3+掺杂TiO2的制备及性能

利用溶胶-凝胶法,在室温条件下,以钛酸四丁酯、硝酸镧为主要原料,无水乙醇为溶剂,冰醋酸为抑制剂,浓硝酸为催化剂制得稳定的掺La3+TiO2溶胶,陈化后的凝胶经不同温度煅烧3h后制得不同掺La3+量的TiO2。通过XRD对不同煅烧温度及不同掺La3+量的TiO2进行了表征;以紫外光为光源,研究了掺La3+-TiO2对甲基橙溶液的光降解效果。用化学共沉淀法制备了具有强磁性的Fe3O4水基磁流体,再与La3+掺杂TiO2进行复合,制备了Fe3O4负载量不同的磁性La3+掺杂TiO2,研究了Fe3O4负载量不同的La3+掺杂TiO2对甲基橙的光催化降解效果、磁分离回收率的影响。结果表明,掺La3+量及煅烧温度对TiO2的晶型、各晶型TiO2的相对含量及对甲基橙的光降解效果均有影响。La3+掺杂TiO2比纯TiO2显示出更强的光催化性能,掺La3+量2%,热处理温度450℃的La3+掺杂TiO2光催化活性最高。Fe3O4负载量为10%的Fe3O4/La3+-TiO2对甲基橙的降解率8h时为99.4%;磁分离回收率达97.39%。     

Eu~(3+)掺杂纳米TiO_2的制备及催化降解亚甲基蓝的研究

采用溶胶-凝胶法制备了Eu3+掺杂的纳米TiO2粉体,采用X射线衍射(XRD)和荧光光谱分析(PL)等手段对TiO2的相结构和TiO2中电子-空穴对的复合性能进行了表征,探讨了掺杂组分对光催化活性的影响机制。以紫外光下降解亚甲基蓝为探针反应,考察铕的掺杂对催化剂催化性能的影响。结果表明Eu3+的掺杂能够通过抑制催化剂晶粒长大从而减少团聚,并且通过降低光生电子-空穴的复合几率,提高催化剂的光催化活性。光催化实验表明,催化剂加入量为3g/L,亚甲基蓝溶液初始浓度为20mg/L时,掺杂1%Eu3+的催化剂催化性能最佳,反应3.5h降解率达到85.5%。     

铁掺杂TiO2纳米粉的制备、表征及其光催化活性

以钛酸丁酯为前驱体,硝酸铁为杂质添加剂,利用溶胶-凝胶法制备了掺铁TiO2纳米粉.以苯酚水溶液的光催化降解反应为探针,评价了掺铁TiO2的光催化性能.借助X射线衍射分析(XRD)、荧光光谱(FS)、热重-差热分析(TG-DTA)等手段对掺铁TiO2催化剂进行了表征.结果表明,掺杂浓度和焙烧温度对掺铁TiO2纳米粉的光催化降解活性有很大影响.掺铁0.5%、煅烧温度为400 ℃的催化剂表现出最佳的光催化活性,在苯酚的降解中催化效率比未掺杂TiO2纳米粉约提高了1倍;并初步探讨了荧光强度对光催化活性的影响.     

Pr-TiO_2光催化剂的制备与性能研究

采用溶胶-凝胶法制备了稀土元素Pr掺杂的纳米TiO2光催化剂(Pr-TiO2)。通过XRD、FT-IR、UV-Vis、TEM等对Pr-TiO2样品进行了表征和分析,并以亚甲基蓝(MB)作为目标降解物,考察了不同热处理温度及不同掺杂量的Pr-TiO2对MB的光催化降解效果。结果表明,Pr掺杂纳米TiO2的晶型为锐钛矿相和金红石相的混晶相,Pr的掺入提高了TiO2光催化活性。当热处理温度为500℃,在pH值为2.5,Pr掺杂量为n(Pr):n(TiO2)=1:300的条件下制备的光催化剂的催化活性显著高于DegussaP25。     

电气石/La/TiO2光催化材料的合成与表征

以硝酸镧、天然电气石(Tourmaline,简称T)和钛酸丁酯为原料,采用溶胶-凝胶法制备掺杂电气石和稀土La的TiO2复合光催化薄膜样品。用正交试验方法对影响该薄膜样品光催化性能的制备工艺进行优化,并通过紫外可见光谱对复合薄膜样品的吸收光谱进行分析。结果表明,掺杂稀土元素La可使TiO2的光吸收范围发生红移,掺杂电气石将增强La/TiO2光吸收强度,T/La/TiO2复合光催化薄膜最佳制备工艺为:La3+掺杂量为1.2%(wt,下同)、电气石掺杂量为0.8%、焙烧温度为500℃、焙烧时间为1.5h、负载次数2次,样品的的甲醛降解率可达82.5%。     

Ce掺杂TiO2薄膜电极光电催化降解甲基橙

用溶胶-凝胶法制备了泡沫镍负载TiO2及Ce离子掺杂TiO2薄膜电极,并以其为工作电极,建立了三电极光电催化体系。通过对水溶液中甲基橙的降解实验,考察了催化剂热处理温度、涂敷层数、外加电压、铈掺杂等因素对薄膜催化剂光催化性能的影响,结果表明,泡沫镍是光催化剂的优良载体;经500℃处理所得催化剂主要为锐钛矿相,催化活性最好;外加适当电压,有助于光催化降解;Ce的掺杂有易于TiO2催化活性的改善;外加适当电压有助于甲基橙的光催化降解。研究证明,500℃为铈掺杂TiO2薄膜的最佳热处理温度,外加一定电压、涂敷3层、掺杂n(Ce)/n(Ti)=2%的铈时催化剂的活性最高。     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Synthesis of Alumina-Zirconia Nanocomposites by Solgel Process

Al₂O₃-ZrO₂ nanocomposites were developed starting with the solgel process. Composite alumina-zirconia nanopowders were synthesized from metallorganic precursors (Aluminium secondary butoxide and zirconium Iso propoxide) using the solgel process. The parameters affecting the synthesis—solvent, concentration of precursor, R/H ratio (i.e., dilution of water in solvent)—were varied as also the temperature and pH. BET and TEM were used to measure nanosize. Diffuse reflectance spectroscopy and also qualitative optical absorption led to identical particle size estimate. The variation of process parameters was used to study the effect and interdependence of process parameters. Artificial Neural Networks was used to rigorously analyze the process. Although this led to confirmation of interdependence of parameters, the presence of a single overwhelming solvent variable was also established. Then the optimal process was used to synthesize more nanopowder. To produce bulk nanocomposite the nanopowders were sintered by varying the temperature and time period. The sintered lithoids were probed with a vickers hardness tester to measure elastic modulus, hardness, and fracture toughness. The results showed high elastic modulus, modest hardness, and very high fracture toughness.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Friction Stir Processing Strategies for Uniform Distribution of Reinforcement in a Surface Composite

Friction stir processing (FSP) is an important technique for preparing surface composites. Fabricating defect-free surface composites with uniform particle distribution by FSP is a challenging task. In this study, silicon carbide particles reinforced AA5083 alloy surface composites was fabricated using different FSP strategies including variation in process parameters, dual-tool processing and tool offset overlapping. Material flow of the processed material with reinforcement particles demonstrated that the distribution of particles was influenced by the stirring action of the probe as well as the extrusion of the plasticized material due to the movement of the tool. Process parameters, particularly rotational speed, showed a dominant influence on the distribution of silicon carbide particles.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.