共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
3.
4.
基于动力学有限元模型的多跨转子轴系无试重整机动平衡研究* 总被引:3,自引:0,他引:3
针对多跨转子轴系现场动平衡需频繁启停机的问题,结合影响系数平衡法和模态振型平衡法特点,提出一种新的基于动力学有限元模型的轴系无试重整机动平衡法。综合转子动力学相关理论和有限元技术,通过仿真构建与轴系结构尺寸和运行参数相符的转子动力学有限元模型。采用柔性转子共振分离原理,分析轴系振型和不平衡振动阶次以确定各跨转子加重平衡平面数和位置,分别在各跨转子平衡位置处施加不平衡激励,获取轴系平衡转速下各振动测点处不平衡响应,计算出相应的加重影响系数,从而取代轴系现场动平衡中需要多次启停机试重测取过程。然后采用最小二乘法通过解平衡矢量方程组得到轴系所需的平衡配重。最后以模拟百万兆瓦超超临界汽轮机的四跨五支承柔性转子轴系试验台为例,应用该方法开展了2 700 r/min转速下轴系四个平面同时配重动平衡试验,单点降幅最高达53%,实现了无试重下柔性转子轴系整机动平衡,可有效减少因盲目试重次数,节省平衡费用和周期。 相似文献
5.
6.
在转子现场平衡ZF法的基础上,提出了进一步提高不平衡量现场测相精度的新方法。经理论分析和试验验证,该法在现有振幅测量精度的前提下,可以有效地提高不平衡量的现场测相精度,提高了转子一次平衡降低率。 相似文献
7.
提出了一种用于单面现场动平衡的平行四边形加重法。在叶轮上加试重,并测试相应振动值,用公式就可计算出不平衡量的大小和位置。试验证明该方法简单、方便可行。 相似文献
8.
单面现场动平衡解析三点加重法试验研究 总被引:1,自引:0,他引:1
提出了一种用于单面现场动平衡的解析三点加重法,在叶轮上三个等分点分别加试重,并测试相应振动值,用公式就可以计算出不平衡量的大小和位置,实验证明这种方法简单,方便可行。 相似文献
9.
10.
11.
12.
In a recent paper, the Ritz method with simple algebraic polynomials as trial functions was used to obtain an eigenvalue equation for the free vibration of a class of homogeneous solids with cavities. The method presented is here extended to the study of a class of non-homogeneous solids, in which each solid is composed of a number of isotropic layers with different material properties. The Cartesian coordinate system is used to describe the geometry of the solid which is modelled by means of a segment bounded by the yz, zx and xy orthogonal coordinate planes and by two curved surfaces which are defined by fairly general polynomial expressions in the coordinates x, y and z. The surface representing the interface between two material layers in the solid is also described by a polynomial expression in the coordinates x, y and z. In order to demonstrate the accuracy of the approach, natural frequencies are given for both a two- and three-layered spherical shell and for a homogeneous hollow cylinder, as computed using the present approach, and are compared with those obtained using an exact solution. Results are then given for a number of two- and three-layered cylinders and, to demonstrate the versatility of the approach, natural frequencies are given for a five-layered cantilevered beam with a central circular hole as well as for a number of composite solids of more general shape. 相似文献
13.
我公司于80年代末引进Aspera公司年产80万台冰箱(冷柜)压缩机生产线及软件技术,在压缩机加工中,活塞销孔(如图1所示)的加工是难点之一。用镗床加工,质量一直难以达到要求,废品率很高。后来我们将Aspera公司的加工工艺即精镗后滚光改为精镗后用金刚石铰刀粗、精铰孔,由此解决了这个技术难题。(1)原意大利Aspera公司工艺简述其工艺流程为:钻6.5通孔→扩孔至7+0.1→粗镗7.473+0.036、圆柱度0.01→精镗至7.935+0.006、圆柱度0.002→滚光7.938+0.006、圆柱度0… 相似文献
14.
根据广州市珠江新城旅客自动运输系统(APM)列车的运行特点,介绍APM列车制动系统的制动方式及其特点,分析APM列车动态制动和摩擦制动的工作机理及其区别和联系,阐明APM列车制动系统的电控制过程和气控制过程,从而为APM列车制动系统的维护和管理提供一定的依据. 相似文献
15.
三爪自定心卡盘作为机床的主要附件,已有一百多年的发展历史,尽管目前随着数控技术的不断发展,越来越多地需求高速动力卡盘,但三爪自定心卡盘目前仍有一定的市场。 要保证卡盘可靠地夹紧工件,必须使其有可靠的夹持精度;要保持卡盘的精度,必须要严格控制各零部件公差及误差,如盘丝的极心偏。 极心偏是形成圆的渐开线的基圆圆心 (极心 )与盘丝内孔中心不同心所造成的偏差值。它对卡盘精度的影响分两种情况,一是卡爪夹持弧采用配磨,二是卡爪夹持弧采用单磨。本文主要探讨配磨时的影响。 卡爪夹持弧采用配磨,即每台卡盘整体… 相似文献
16.
17.
详细分析了圆柱面素线的直线度公差带在新旧标准中定义和解释的区别,并从对圆柱面素线实际要素检测的角度,提出了推行新标准的实际意义。 相似文献
18.
通过分析膨胀套在实际使用产生滑移受阻现象、卡死现象原因的实质,并在分析产生问题原因的基础上提出了改进措施即:增加导向机构。 相似文献
19.
设计了磨粉机快辊轴承座的加工工艺和具体的工装夹具.利用卧式加工中心加工磨粉机快辊轴承座,辅以能够高效快速夹紧的夹具,既可以保证加工精度,又能够提高加工效率. 相似文献
20.
The article presents a brief review of the wear models based on the kinetic thermofluctuation approach. The materials were developed using SamGTU sclerometric programming software and a set of instruments developed at Samara Engineering University for assessing the parameters of kinetic thermoactivation for surface fracture deformed by friction. The first obtained results of assessments and the estimated prediction of wear resistance exemplified by tribocouple of the aircraft chassis are presented. 相似文献