聚苯乙烯/纳米SiO2复合颗粒制备与表征

为改善二氧化硅(SiO2)纳米粒子与聚合物基体间的亲和性,使SiO2表面功能化,将硅烷偶联剂KH-570引入C=C基团,采用乳液聚合方法在纳米SiO2粒子表面接枝苯乙烯(St)单体,实现了纳米二氧化硅表面的聚苯乙烯(PS)高分子包覆改性,制备了具有核/壳结构的SiO2-PS复合纳米粒子,产物的单体转化率和接枝效率在80%以上.研究了二氧化硅含量和偶联剂用量对聚合反应的单体转化率和接枝效率的影响,探讨了偶联剂的作用机理,利用FT-IR、TEM、TG对SiO2-PS复合粒子的表面结构进行了表征.结果表明,复合粒子具有明显的核壳结构,壳层厚度在20nm左右,乳液聚合过程可有效使二氧化硅的团聚体剥离呈纳米级颗粒.     

核壳结构CdS：Mn/ZnS纳米晶的制备与光学性能研究

以3-巯基丙酸为稳定剂,采用共沉淀法在水相中合成了CdS∶Mn掺杂纳米晶,然后进一步将ZnS包覆于CdS∶Mn纳米晶表面,制备了CdS∶Mn/ZnS核壳结构纳米晶。利用X射线衍射（XRD）,透射电子显微镜（TEM）和紫外-可见吸收光谱（UV-Vis）对纳米晶的结构、形貌和光学性质进行了表征,发现制备的纳米晶具有优秀的单分散性,确认合成了CdS∶Mn/ZnS核壳结构纳米晶。通过荧光光谱（PL）研究了纳米晶的发光性质和光稳定性,结果表明包覆壳层后纳米晶的发光强度显著提高,最高可达8倍,且Mn2＋离子的发光峰峰位置随着ZnS壳层数的增加而红移。此外,核壳纳米晶的光稳定性大大提高。     

介孔SiO2负载和包覆的纳米金属颗粒的制备与研究

制备了以SiO2为核、介孔SiO2为壳的核-壳颗粒负载纳米金属颗粒以及介孔SiO2壳层包覆SiO2负载的纳米金属颗粒。结果表明,十六烷基三甲基溴化胺(CTAB)作为模板剂,有助于介孔SiO2壳层包覆SiO2核的结构形成,介孔SiO2壳层的孔径方向垂直于SiO2核的表面;在聚乙烯吡咯烷酮(PVP)的稳定作用下,Pt纳米颗粒能均匀地分布在介孔SiO2壳层的表面。单分散SiO2颗粒经过3-氨丙基三乙氧基硅烷(APS)功能化后,可负载纳米金属颗粒。进一步研究表明,以SiO2负载纳米金属颗粒为核,NH3.H2O,乙醇和水为分散剂,CTAB为模板剂,正硅酸乙酯(TEOS)为硅源,还能制备介孔SiO2壳包覆SiO2负载的纳米金属颗粒,而且介孔SiO2壳层的厚度可通过TEOS的含量调节。     

α-N（OH）2/SiO2核壳以及α-Ni（OH）2空心微球的制备及表征

采用以正硅酸乙酯（TEOS）水解为基础的硅溶胶种子生长法制备了粒径约为270nm的近单分散二氧化硅球型颗粒.采用一种新的溶液生长法,以氢氟酸作为溶液中镍离子配位剂,加入氨水调节溶液pH值的同时作为镍离子补充配位剂,60℃水浴条件下在已制得SiO2微球表面均匀包覆α-Ni（OH）2得到Ni（OH）2/SiO2核壳结构,Ni（OH）2壳层厚度约为35nm.结合多步包覆法提高Ni（OH）2壳层厚度,三次包覆后壳层厚度达到约100nm,四次包覆后约为140nm.采用20wt%的强碱NaOH溶液对三次包覆后的Ni（OH）2/SiO2核壳结构进行处理,得到了壳层厚度约为95nm的α-Ni（OH）2空心微球.空心微球具有较大的比表面积为141.06m2/g.     

不同壳层的CdS／ZnS核／壳结构量子点的温度相关荧光性质

报导了CdS／ZnS纳米晶体（NCs）的制备过程和其光学}生质。通过采用连续离子层吸附和反应技术（SILAR）,我们用少量的表面活性剂合成了不同壳层的四个样品,包括CdS核纳米晶以及具有1～3层ZnS壳的CdS／ZnS核／壳结构纳米晶体样品。发现具有一层ZnS壳的CdS／ZnS样品的荧光量子产率大约比未包覆壳层的CdS纳米晶体样品的强11倍。另外,随着壳层的增加（增至两到三层）,荧光量子产率呈现下降的趋势。对样品进行了温度相关的光谱测量,发现CdS／ZnS和CdS一样具有特殊的光学特性。     

核-壳式聚苯乙烯/二氧化硅复合微球及空腔硅球的制备

利用层层自组装的方法制备了粒径和组成可裁剪、具有核-壳式结构的单分散聚苯乙烯(PS)/二氧化硅(SiO₂)复合微球.对复合微球进行热处理除去有机物中心,制备出壁厚可剪裁的空腔硅球.透射电镜(TEM)照片显示二氧化硅纳米颗粒在中心外生成均匀壳层,而煅烧后则可得到轮廓分明的球形空腔;热重分析(TG)说明复合球体的硅含量随着所组装的纳米二氧化硅的粒径的增加而增加;比较PS、SiO₂、复合球体及热处理后的粉体的红外光谱,可分别验证二氧化硅的成功组装和热处理过程中作为中心的PS的完全去除.在吸附相同层的前提下,随着所选用的二氧化硅纳米粒子(10um,20um,40um)的粒径的增大,复合微球的粒径增大,空腔球体的壁厚增加.     

低对称性SiO2/Ag核壳复合纳米结构的银镜反应制备及表面增强拉曼散射活性研究

利用银镜反应在自组装的SiO2纳米粒子单层膜上制备了低对称性的SiO2/Ag核壳复合纳米结构.通过透射电镜(TEM)、扫描电镜(SEM)和紫外-可见分光光度计(UV-Vis)对核壳复合纳米结构的表面形貌和光学性质进行了表征.以亚甲基蓝作为探针分子,研究了低对称性SiO2/Ag核壳复合纳米结构的表面增强拉曼散射(SERS)活性.     

核壳结构Co/SiO_2非晶态纳米颗粒的制备和性能

主要研究了核壳结构Co/SiO2非晶态纳米颗粒的制备及性能。正硅酸乙酯水解生成二氧化硅,水溶液中硼氢化钠还原氯化钴生成钴单质,存在硅烷偶联剂APS时,将二者进行结合生成二氧化硅包覆在钴颗粒表面。采用XRD、TEM、FT-IR、VSM等手段对样品进行表征。     

金、银纳米粒子包覆核壳结构微球的制备与研究进展

金、银纳米粒子包覆的核-壳结构微球在众多领域具有许多潜在的应用功能,也是近几年来的一个研究热点。本文分析和讨论了金、银纳米粒子包覆的核-壳结构微球的制备方法,包括静电自组装法、原位还原法、晶种生长法、化学镀法、超声法、一步合成法等;简述了金、银纳米粒子包覆的核壳结构微球的优异性能及其应用,并对其发展前景进行了展望。     

分散聚合法制备SiO2/PAM核壳复合微球

采用分散聚合法制备出以SiO2为核、PAM为壳的核壳复合微球。根据Stber法制备了单分散SiO2微球,粒径随着TEOS、氨水浓度的增加而增大。采用硅烷偶联剂对SiO2微球进行表面处理,TEM显示处理后的微球继续保持单分散性,粒径有所增加。以SiO2微球或处理后的SiO2微球为核,采用分散聚合法在其上包覆AM,借助TEM、IR对其进行表征;研究发现,以处理后的Si O2微球为核能得到核壳结构,这种SiO2/PAM核壳微球的粒径大约为163 nm,包覆层30 nm左右。     

Facile fabrication of wurtzite ZnS hollow nanospheres using polystyrene spheres as templates

Wurtzite ZnS hollow nanospheres were fabricated using PS nanospheres as templates by a facile method at relative low temperature. The prepared hollow nanospheres are uniform, monodispersed with homogeneous size of around 480 nm, and spherical shape. The shell thickness of these hollow nanospheres is about 60 nm, and composed of many wurtzite ZnS nanocrystals with the size of 8 nm. The definite shape, thick and denser shell with higher specific surface area reveals that these hollow nanospheres will find a great deal of potential applications in environment protection, photocatalysis and so on.     

Preparation and characterization of acrylated-SiO2@TiO2 hollow hybrid nanospheres

Novel inorganic-organic hybrid hollow nanospheres, acrylated SiO2 and SiO2@TiO2, were synthesized via a sol-gel polymerization, using crown-appended sugar gelator 1 as an organic template for the unique nanospherical structures in demand for a fast expanding area in nanomaterial research. In this work, hollow SiO2 nanospheres were obtained by a simple sol-gel method followed by calcination and rather rough TiO2 nanolayers were coated onto the highly dispersed surface of SiO2 nanospheres and further copolymerization of MPA on the surface of SiO2 and SiO2@TiO2 nanosphseres was successfully conducted. The morphological properties of those hollow nanospheres were characterized by TEM, SEM and powder-XRD. Furthermore, the physical and chemical properties of the synthesized nanocomposites were characterized by the analysis of EDX, FT-IR, TGA and ESCA.     

Fabrication of hollow polyelectrolyte nanospheres via surface-initiated atom transfer radical polymerization

Novel polyelectrolyte-grafted core-shell organic/inorganic hybrid nanospheres which possess hard backbone of silica nanoparticles and soft shell of cross-linked poly(ionic liquids) (PILs) have been synthesized via a surface-initiated atom transfer radical polymerization (SI-ATRP). After removal of the core templates of the core-shell nanospheres, nearly monodispersed hollow polyelectrolyte nanospheres were obtained. Various characterization techniques including FT-IR, XPS, and TEM were used to characterize the resulting core-shell and hollow polyelectrolyte nanospheres. The results showed that the hollow nanosphere has a hollow core of an average diameter of ca. 200 nm with a shell thickness of ca. 25 nm. The obtained hollow polyelectrolyte nanospheres could be applied in release-control systems.     

SiO2空心微球的制备与表征

以自制的微米级碳酸钙颗粒为模板,正硅酸乙酯为硅源,通过溶胶-凝胶方法合成出CaCO3/SiO2核壳结构;随后通过高温煅烧、酸浸和干燥处理,制备出圆形度高、分散性好、结构完整的微米级SiO2空心球。并利用SEM、XRD、FTIR、TG和压缩实验等方法对空心微球的形貌、结构和抗压强度进行了分析和测定。SiO2空心微球的粒径为2-5μm,壳层厚度为0.42-0.85μm,比表面积为554.01m^2/g,最可几孔径为1.7nm,抗压强度在20~30MPa之间。     

SiO_2/SiCN核壳陶瓷微球的制备及表征

采用乳液技术和先驱体转化法相结合,利用改性后SiO_2颗粒表面的双键引发聚硅氮烷(PSN)原位聚合,得到SiO_2/PSN核壳结构微球,经高温裂解过程成功制备SiO_2/SiCN核壳陶瓷微球。研究SiO_2与PSN原料的质量比、固化时间和热解温度对核壳微球形成过程和形貌的影响,并采用SEM,EDS,TEM,FT-IR,XRD对微球的微观形貌、化学成分及物相进行表征。结果表明:SiO_2与PSN质量比为1∶4时,200℃固化4h得到表面颗粒分布均一、包覆完全的SiO_2/PSN核壳微球;经800~1200℃热处理后,得到能保持原来形貌的非晶态SiO_2/SiCN核壳陶瓷微球;1400℃热解产物发生结晶,生成了SiO_2,SiC和Si_3N_4晶相。     

Solid ion transition route to 3D S–N-codoped hollow carbon nanosphere/graphene aerogel as a metal-free handheld nanocatalyst for organic reactions

A novel metal-free bulk nanocatalyst,S-N-codoped hollow carbon nanosphere/graphene aerogel (SNC-GA-1000),has been successfully fabricated using a facile and clean solid ion transition route.In this method,ZnS is used as the hard template and S source,while polydopamine acts as a reducing agent and carbon source.At a high annealing temperature,Zn metal is reduced and evaporates,leaving only free S vapor to diffuse into the carbon layer.Interestingly,the as-obtained SNC-GA-1000 exhibits much higher catalytic activity in an organic reduction reaction than unloaded bare S-N-codoped carbon nanospheres.Hydrothermal reduction of the graphene oxide sheets loaded with ZnS@polydopamine core-shell nanospheres (ZnS@PDA) affords a three-dimensional bulk graphene aerogel.Although nanosized catalysts exhibit high catalytic activities,their subsequent separation is not always satisfactory,making post-treatment difficult.This approach achieves a trade-off between activity and separability.More importantly,due to the 3D structural nature,such bulk and handheld nanocatalysts can be easily separated and recycled.     

A versatile approach for the fabrication of Au hollow nanoparticles based on poly(styrene-co-2-aminoethyl methacrylate) template

The hollow Au nanospheres were successfully prepared by the template method. The poly(styrene-co-2-aminoethyl methacrylate hydrochloride) (P(St-co-AEMH)) nanoparticles synthesized by the emulsion polymerization were used as the templates. After coating by Au colloidal nanoparticles and the formation of Au shells, the interior templates were etched out by sulfuric acid, leading to the formation of Au hollow nanospheres. The structure and morphology of the nanoparticles and hollow nanospheres were carefully investigated by the fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray analysis (EDX), wide-angle X-ray diffractometer (WAXD), and thermal gravimetric analysis (TGA) techniques.     

纳米尺度PS/Ag核壳结构复合球的制备与表征

采用分步法制备了聚苯乙烯/银(PS/Ag)核壳结构复合纳米球。首先采用无皂乳液聚合法并利用丙烯酸(AA)的羧基对制备的PS球进行改性,使其表面带负电荷;然后通过静电吸附作用在改性PS球的表面沉积[Ag(NH3)2]+,水浴(80℃)环境中利用十二烷基磺酸钠(SDS)作为还原剂将PS球表面的[Ag(NH3)2]+还原,制备出PS/Ag核壳结构复合球。通过动态激光粒度分析仪和透射电子显微镜对PS/Ag核壳纳米球的粒度分布、形貌和结构进行了表征,研究了AA的用量对复合球粒径及包覆的Ag壳厚度的影响。结果表明,随着AA用量的增大,所包覆的银层更加致密,厚度增大,当AA用量为15%时可得到Ag完全包覆的PS/Ag复合纳米球。     

Preparation of hollow carbon nanospheres via explosive detonation

Hollow carbon nanospheres were prepared via a rapid detonation technique, by using negative-oxygen balance explosive trinitrotoluene and nickel powder as starting materials and inorganic acid as solvent. The carbon/metal nanocomposite particles precursor with core-shell structure was engendered firstly during detonation, and then the metal nickel core was dissolved through inorganic acid to attain the hollow carbon nanospheres. High-Resolution Transmission Electron Microscope, X-ray diffraction and Raman spectrum were used to characterize the precursor and the as-synthesized samples respectively. The results show that the external diameter of the hollow carbon nanospheres is 25-150 nm and the thickness of the wall is about 2-10 nm. The surface of hollow carbon nanosphere displays multilayer wall in structure with 0.35 nm space between the layers. Based on the experimental results, possible formation mechanism was also proposed.     

Mn掺杂ZnO囊泡结构的制备

通过两步或三步法分别制备两层或三层结构的碳球模板,在溶液中的Zn离子和Mn离子在模板上吸附后再进行煅烧.TEM及SEM显示,煅烧后得到完全复制碳膜板结构的多层Mn掺杂ZnO囊泡.EDS显示Mn在ZnO中的掺杂含量约为1％.样品具有室温铁磁性,饱和磁化率(Ms)及矫顽磁场(Hc)分别为0.032A·m²/kg及0.781kA/m.这种Mn掺杂ZnO纳米囊泡结构使新奇的囊泡结构和ZnO的磁性性能得到了完美的结合.