Effect of Solvent on Titania Particle Formation and Morphology in Thermal Hydrolysis of TiCl4

Titania powders were synthesized by the thermal hydrolysis of titanium tetrachloride with the yield of above 85% in a mixed solvent of n -propanol and water. The morphology of the precipitates was controlled by adjusting the volume ratio of n -propanol to water (RH ratio) of the mixed solvent. Precipitates obtained with an RH ratio of 0 were fine, and highly agglomerated. In contrast, an RH ratio of 3 resulted in precipitates consisting of uniform and discrete particles. According to observations of the zeta potentials of precipitates and the dielectric constants of solvents, the discrete particles obtained with an RH ratio of 3 resulted from the low zeta potential and dielectric constant. The result of Fourier transform infrared (FTIR) spectroscopy showed the chemical interaction of particle surface with the solvent alcohol, which decreased the zeta potential of precipitates with an increase of RH ratio. Adding hydroxypropyl cellulose (HPC) as a steric dispersant made it possible to reduce the size of particles to the submicrometer range. Effects of the solvent on the formation and morphology of the resulting particles were investigated.     

La2Ti2O7 Ceramics

La₂Ti₂O₇ powders were prepared using three different techniques. Single-phase material was obtained at 1150°C by calcination of mixed oxides, at 1000°C by molten salt synthesis, and at 850°C by evaporative decomposition of solutions. Particle sizes and morphologies of the powders differed substantially, as did the sintered microstructures and dielectric properties. Very dense (99%), translucent, grain-oriented lanthanum titanate was fabricated by hot-forging at 1300°C under a 200-kg load. Anisotropy was demonstrated by X-ray diffraction, scanning electron microscopy, thermal expansion, and dielectric measurements.     

Methanol–Water System for Solvothermal Synthesis of YVO4:Eu with High Photoluminescent Intensity

A methanol–water mixed solvent was used as a reaction medium for the preparation of Eu³⁺-doped YVO₄ phosphor materials. These were synthesized by a solvothermal method at 150°–300°C using a 10 vol% solution of water in methanol as the reaction medium followed by calcination at 1000°–1200°C. The phase composition and optical properties of the products were characterized by X-ray diffraction, scanning electron microscope, and photoluminescence spectroscopy. The powders obtained were composed of spherical particles ∼0.5 μm in size, with an internal structure that was different for samples prepared under subcritical and supercritical conditions of methanol. After the calcination, the powders obtained at 240°–300°C retained the initial raspberry-like morphology, whereas the morphology of samples prepared at 150°–210°C changed significantly due to noticeable sintering. The fluorescence intensity exhibited by the prepared samples was higher than the fluorescence intensity shown by one of the best commercial YVO₄:Eu phosphors having a large particle size.     

Low-Temperature Synthesis of NiFe2O4 by a Hydrothermal Method

Nickel ferrite (NiFe₂O₄) nanoparticles were successfully synthesized via a hydrothermal process and characterized by X-ray diffraction and transmission electron microscope techniques. The effects of reaction temperature, holding time, and RH ratio (isopropyl alcohol/water) were discussed. The NiFe₂O₄ nanoparticles could be obtained at 60°C within 3 h. The crystallization of the spinel ferrites was promoted by the increase in reaction temperature, holding time, and RH ratio.     

Fabrication of Grain-Oriented Bi2WO6 Ceramics

Grain-oriented Bi₂WO₆ ceramics were fabricated by normal sintering techniques. Platelike crystallites were initially synthesized by a fused salt process using an NaCl-KCI melt. When calcined at <800°C, the Bi₂WO₆ crystallites are 3∼5 μ m in size and, at >850°C, =100 μm. After dissolving away the salt matrix, the Bi₂WO₆ particles were mixed with an organic binder and tapecast to align the platelike crystallites. Large particles were easily oriented by tapecasting but the sinterability of the tape was poor. Preferred orientation of small particles was increased by tapecasting and grain growth during sintering further improves the degree of orientation. Sintering above the 950°C phase transition, however, results in discontinuous grain growth and low densities. Optimum conditions for obtaining highly oriented ceramics with high density occur at sintering temperatures of 900°C using fine-grained powders which yield orientation factors of =0.88 and densities of 94% theoretical.     

Novel Synthesis of SrBi2Nb2O9 Powders From Hydroxide Precursors

Simple hydroxide precursors were used for the first time for the synthesis of a typical Aurivillius compound (SrBi₂Nb₂O₉ (SBN)) at a low temperature. This method is very advantageous because it circumvents the use of SrCO₃ in the case of conventional ceramics as well in the coprecipitation methods, thereby lowering the formation of the product phase. Commercially purchased strontium hydroxide is mixed thoroughly with freshly precipitated bismuth and niobium hydroxides in a stoichiometric ratio and heated at different temperatures ranging from 100°C to 750°C for 12 h. The sequence of the reaction and evolution of the product phase was monitored by X-ray diffraction (XRD) studies by recording the XRD for samples calcined at different temperatures. The incipient SBN phase begins to form at temperatures as low as 400°C, and phase formation was complete only at 650°C as revealed by the XRD observations. The differential thermal/thermogravimetric analyses) also corroborate this result. The morphology and average particle size of these powders were investigated by transmission electron microscopy studies.     

Homogeneous Precipitation of TiO2 Ultrafine Powders from Aqueous TiOCl2 Solution

Crystalline TiO₂ powders were prepared by the homogeneous precipitation method simply by heating and stirring an aqueous TiOCl₂ solution with a Ti⁴⁺ concentration of 0.5 M at room temperature to 100°C under a pressure of 1 atm. TiO₂ precipitates with pure rutile phase having spherical shapes 200-400 nm in diameter formed between room temperature and 65°C, whereas TiO₂ precipitates with anatase phase started to form at temperatures >65°C. Precipitates with pure anatase phase having irregular shapes 2-5 µm in size formed at 100°C. Possibly because of the crystallization of an unstable intermediate product, TiO(OH)₂, to TiO₂ x H₂O during precipitation, crystalline and ultrafine TiO₂ precipitates were formed in aqueous TiOCl₂ solution without hydrolyzing directly to Ti(OH)₄. Also, formation of a stable TiO₂ rutile phase between room temperature and 65°C was likely to occur slowly under these conditions, although TiO₂ with rutile phase formed thermodynamically at higher temperatures.     

Dense Al2O3/ZrO2 Particulate Composites by Free Sintering of Coated Powders

Composite powders, prepared by coating coarse ZrO₂ particles with fine Al₂O₃ powder using a chemical precipitation technique, were compacted and sintered freely at a constant heating rate of 4°C/min to ∼1600°C. Composites containing up to ∼30 vol% inclusions were sintered to nearly full density under the same conditions used for the unreinforced matrix. Furthermore, the sintering kinetics were not influenced significantly by the inclusion volume fraction. The sinterability of the composites formed from the coated powders was significantly better than that for similar composites formed from mechanically mixed powders. The present data provide a further demonstration that the use of coated powders may have widespread applicability for the fabrication, by free sintering, of dense ceramic particulate composites.     

Synthesis of Transparent Nd-doped HfO2-Y2O3 Ceramics Using HIP

A Nd-doped HfO₂-Y₂O₃ ceramic having excellent transmittance was synthesized by HIPing, using high-purity powders (>99.99 wt%) of Y₂O₃, Nd₂O₃, and HfO₂. The mixed powder compacts of these powders were sintered at 1650°C for 1 h under vacuum and HIPed at 1700°C for 3 h under 196 MPa of Ar. The specimen after HIPing consisted of uniform grains measuring about 30 μm and having pore-free structure. The optical transmittance of 1 at.% Nd-doped 2.6 mol% HfO₂-Y₂O₃ ceramics ranging between visible and infrared wavelength was almost equivalent or superior to that of a Nd:Y₂O₃ single crystal grown by the Verneuil method.     

Preparation of Submicrometer A12O3 Powder by Gas-Phase Oxidation of Tris (acetylacetonato) aluminum (111)

Fine A1₂O₃ powder was prepared by the gas-phase oxidation of aluminum acetyl-acetonate. The reaction products were amorphous material at 600° and 800°C, γ-Al₂O₃ at 1000° and 1200°C, and δ-Al₂O₃ at 1400°C. The powders consisted of spherical particles from 10 to 80 nm in diameter; particle size increased with increasing reaction temperature and concentration of chelate in the gas.     

Synthesis of Ti3AlC2 Powders Using Sn as an Additive

Nearly pure Ti₃AlC₂ powders have been synthesized by calcining a mixture of titanium, aluminum, and graphite powders using tin powders as additives. Four recipes with different mole ratios of Ti:Al:C:Sn were examined at calcining temperatures from 1300° to 1500°C. The addition of Sn effectively inhibited the generation of thermal explosion when the volume of the starting materials is larger, and considerably reduced the lower-limit calcining temperature. The nearly pure Ti₃AlC₂ powders can be obtained reliably on a large scale by calcining the starting materials with a mole ratio of 3Ti:1Al:1.8C:0.2Sn at temperatures from 1350° to 1500°C.     

Zirconium Aluminum Carbides: New Precursors for Synthesizing ZrO2–Al2O3 Composites

ZrO₂–Al₂O₃ nanocrystalline powders have been synthesized by oxidizing ternary Zr₂Al₃C₄ powders. The simultaneous oxidation of Al and Zr in Zr₂Al₃C₄ results in homogeneous mixture of ZrO₂ and Al₂O₃ at nanoscale. Bulk nano- and submicro-composites were prepared by hot-pressing as-oxidized powders at 1100°–1500°C. The composition and microstructure evolution during sintering was investigated by XRD, Raman spectroscopy, SEM, and TEM. The crystallite size of ZrO₂ in the composites increased from 7.5 nm for as-oxidized powders to about 0.5 μm at 1500°C, while the tetragonal polymorph gradually converted to monolithic one with increasing crystallite size. The Al₂O₃ in the composites transformed from an amorphous phase in as oxidized powders to θ phase at 1100°C and α phase at higher temperatures. The hardness of the composite increased from 2.0 GPa at 1100°C to 13.5 GPa at 1400°C due to the increase of density.     

Magnesium Aluminate (MgAl2O4) Spinel Powders from Water-Based Sols

Magnesium aluminate (MgAl₂O₄) spinel powders of irregular and spherical morphologies were obtained from the bi-component water-based sols following the sol–gel and sol–emulsion–gel methods, respectively. For the synthesis of the oxide microspheres, the surfactant concentration and viscosity of the sols were found to affect the characteristics of the derived microspheres. The gel and calcined powders were investigated by using thermogravimetry analysis, differential thermal analysis, X-ray diffraction (XRD), optical and scanning electron microscopy (SEM), Fourier transformed infrared spectroscopy, and particle size analysis. XRD results indicated crystallization of the only phase MgAl₂O₄ spinel from 200° to 1000°C. Formation of hollow microspheres with a single cavity was identified by SEM.     

High-Temperature Characteristics of Transition Al2O3 Powder with Ultrafine Spherical Particles

Ultrafine transition Al₂O₃ powder with spherical particles was prepared by an arc-discharge method. High-temperature characteristics were found to be superior to those of commercial A1₂O₃ powders by DTA, specific surface-area measurements, XRD, and TEM. The powder studied transformed to α-phase at about 1335°C. After heat treatment at 1260°C for 1 h, the specific surface area of the powder decreased from 25.0 to 17.3 m²/g. Some particles were able to retain the transition phase even after 106 h at 1160°C.     

Synthesis, Characterization, and Consolidation of Si3N4 Obtained from Ammonolysis of SiCl4

Thermal decomposition of silicon diimide, Si(NH)₂, in vacuum resulted in very-high-purity, fine-particle-size, amorphous Si₃N₄ powders. The amorphous powder was isothermally aged at 50° to 100° intervals from 1000° to 1500°C for phase identification. Examination of ir spectra and X-ray diffraction patterns indicated a slow and gradual transition from an amorphous material to a crystalline α-phase occurring at 1200°C for >4 h and/or 1300° to 1400°C for 2 h. As the temperature was increased to ≥1450°C for 2 h, the crystalline β-phase was observed. Phase nucleation and crystallite morphology in this system were studied by electron microscopy and electron diffraction combined with TG as functions of temperature for the inorganic polymer starting materials. Powders prepared in this manner with 4 wt% Mg₃N₂ added as a sintering aid were hot-pressed to high-density fine-grained bodies with uniform microstructures. The optimum hot-pressing condition was 1650°C for 1 h. Silicon concentration steadily increased as the hot-pressing temperature or time was increased. A method for chemical etching for high-density fine-grained Si₃N₄ is described. Electrical measurements between room temperature and ∼500°C indicated dielectric constant and tan δ values of 8.3±0.03 and 0.65±0.05×10⁻², respectively.     

Pyrolysis of Pb(Zr05Ti05)O3 Precursors: Avoiding Lead Partitioning

Three different chemical precursor routes were investigated to synthesize Pb(Zr₀₅Ti₀₅)O₃: mixing hexanoates, acetate complexing of alkoxides, and the synthesis of a mixed alkoxide by the reaction of titanium alkoxide and zirconium alkoxide with lead acetate. For each, elemental Pb and PbO were the first crystalline phase observed during pyrolysis conditions that involved rapid heating (e.g., to 400°C). The formation of Pb (and PbO) could be avoided by first heattreating hydrolyzed, mixed alkoxide precursor powders at 300°C for 1 h. This treatment was not effective for the two other precursors. It is concluded that both the carbonaceous content of the precursor (lowest for the hydrolyzed, mixed alkoxides) and the rate of hydrocarbon release during pyrolysis are critical to avoid the formation of elemental Pb during pyrolysis.     

Single-Calcination Synthesis of Pyrochlore-Free 0.9Pb(Mg1/3Nb2/3)O3–0.1PbTiO3 and Pb(Mg1/3Nb2/3)O3 Ceramics Using a Coating Method

A coating approach for synthesizing 0.9Pb(Mg_1/3Nb_2/3)O₃–0.1PbTiO₃ (0.9PMN–0.1PT) and PMN using a single calcination step was demonstrated. The pyrochlore phase was prevented by coating Mg(OH)₂ on Nb₂O₅ particles. Coating of Mg(OH)₂ on Nb₂O₅ was done by precipitating Mg(OH)₂ in an aqueous Nb₂O₅ suspension at pH 10. The coating was confirmed using optical micrographs and zeta-potential measurements. A single calcination treatment of the Mg(OH)₂-coated Nb₂O₅ particles mixed with appropriate amounts of PbO and PbTiO₃ powders at 900°C for 2 h produced pyrochlore-free perovskite 0.9PMN–0.1PT and PMN powders. The elimination of the pyrochlore phase was attributed to the separation of PbO and Nb₂O₅ by the Mg(OH)₂ coating. The Mg(OH)₂ coating on the Nb₂O₅ improved the mixing of Mg(OH)₂ and Nb₂O₅ and decreased the temperature for complete columbite conversion to ∼850°C. The pyrochlore-free perovskite 0.9PMN–0.1PT powders were sintered to 97% density at 1150°C. The sintered 0.9PMN–0.1PT ceramics exhibited a dielectric constant maximum of ∼24 660 at 45°C at a frequency of 1 kHz.     

Fabrication and Photoluminescence Characteristics of Eu3+-Doped Lu2O3 Transparent Ceramics

A novel co-precipitation process was adopted for the preparation of highly sinterable europium-doped lutetia powders using ammonium hydroxide (NH₃·H₂O) and ammonium hydrogen carbonate (NH₄HCO₃) as the mixed precipitant. The resultant powders calcined at 1000°C for 2 h showed good dispersity and excellent sinterability. Highly transparent polycrystalline lutetia ceramics with a relative density of ∼99.9% were fabricated by pressureless sintering in flowing H₂ atmosphere at 1850°C for 6 h without any additives. The average grain sizes of the transparent material were estimated to be 50–60 μm. Optical in-line transmittance in the visible wavelength region for Lu₂O₃ ceramics (1 mm in thickness) reached 80%. The luminescence and decay behavior of the obtained transparent plate and the corresponding nanophosphors were also investigated.     

Preparation through Aerosols of Cr-Doped Y2Sn2O7 (Pyrochlore) Red-Shade Pigments and Determination of the Cr Oxidation State

A method for the preparation of Cr-doped Y₂Sn₂O₇ powders based on the pyrolysis of aerosols generated from aqueous salt solutions of the corresponding metal cations is reported. These powders yielded Cr-doped pyrochlore red-shade pigments on calcination in the absence of fluxes at lower temperature (900°–1100°C) than that involved in the traditional ceramic method (1400°C). This process resulted in pigment particles with spherical shape and broad size distribution (<10 μm) not requiring milling. The oxidation state of the Cr ions dissolved in the pyrochlore lattice has also been analyzed by using XPS and ESR spectroscopies and ac magnetic susceptibility measurements finding that the color observed for this material is due to Cr(IV) ions, most probably occupying the distorted octahedral position of Sn(IV).     

Molten-Salt Synthesis of Ba1–xPbxTiO3 in the System BaTiO3–PbCl2

Ba_{1– x} Pb _x TiO₃ powder with a fixed composition was prepared by the reaction of BaTiO₃ powders with molten PbCl₂at various PbCl₂/BaTiO₃ molar ratios at 600° and 800°C in a nitrogen atmosphere. When 0.1 μm powder was used, the reaction was finished when x = 0.9. Two phases of BaTiO₃and a solid solution of Ba_{1– x} Pb _x TiO₃ coexisted, but the final phase gave a solid solution of Ba_{1– x} Pb _x TiO₃ at 800°C. When 0.5 μm powder was used, the two phases coexisted in the products at 600°C at PbCl₂/BaTiO₃= 1.0. A sintered compact of Ba_{1– x} Pb _x TiO₃ powders solid solution was prepared by hot isostatic pressing, and its dielectric constant was measured in the temperature range 20°–550°C.