Effects of SmF3 addition on aluminum nitride ceramics via pressureless sintering

Aluminum nitride (AlN) ceramics with dense structure, high thermal conductivity, and exceptional mechanical properties were fabricated by pressureless sintering with a novel non-oxide sintering additive, samarium fluoride (SmF₃). The results showed that the use of a moderate amount of SmF₃ promoted significant densification of AlN and removed the oxygen impurity. This led to the formation of fine and isolated secondary phase that cleaned the grain boundaries and increased the contact between AlN grains, remarkably enhancing thermal conductivity. Furthermore, SmF₃ also exhibited grain refinement and grain boundary strengthening effects similar to traditional sintering additive, samarium oxide (Sm₂O₃), leading to high mechanical properties in SmF₃-doped AlN samples. The most optimal characteristics (thermal conductivity of 190.67 W·m⁻¹·K⁻¹, flexural strength of 403.86 ± 18.27 MPa, and fracture toughness of 3.71 ± 0.19 MPa·m^1/2) were achieved in the AlN ceramic with 5 wt% SmF₃.     

High-strength AlN ceramics by low-temperature sintering with CaZrO3–Y2O3 co-additives

Aluminum nitride (AlN) ceramics with the concurrent addition of CaZrO₃ and Y₂O₃ were sintered at 1450-1700 °C. The degree of densification, microstructure, flexural strength, and thermal conductivity of the resulting ceramics were evaluated with respect to their composition and sintering temperature. Specimens prepared using both additives could be sintered to almost full density at relatively low temperature (3 h at 1550 °C under nitrogen at ambient pressure); grain growth was suppressed by grain-boundary pinning, and high flexural strength over 630 MPa could be obtained. With two-step sintering process, the morphology of second phase was changed from interconnected structure to isolated structure; this two-step process limited grain growth and increased thermal conductivity. The highest thermal conductivity (156 Wm⁻¹ K⁻¹) was achieved by two-step sintering, and the ceramic showed moderate flexural strength (560 MPa).     

Structural,thermal and mechanical properties of aluminum nitride ceramics with CeO2 as a sintering aid

AlN ceramics have been prepared with CeO₂ as a sintering aid at a sintering temperature of 1900 °C. The effect of CeO₂ contents on the microstructure, density, thermal conductivity and hardness was investigated. Addition of CeO₂ exerted a significant effect on the densification of AlN ceramics and hence on the microstructure. Thermal conductivity of AlN ceramics increased with CeO₂ content and was greater than that of Y₂O₃-doped AlN ceramics at a similar sintering temperature. The resulting AlN ceramics with 1.50 wt% of CeO₂ had the highest relative density of 99.94%, thermal conductivity of 156 W m⁻¹ K⁻¹ and hardness of 72.46 kg/mm².     

High thermal conductivity silicon nitride ceramics prepared by pressureless sintering with ternary sintering additives

Silicon nitride ceramics were pressureless sintered at low temperature using ternary sintering additives (TiO₂, MgO and Y₂O₃), and the effects of sintering aids on thermal conductivity and mechanical properties were studied. TiO₂–Y₂O₃–MgO sintering additives will react with the surface silica present on the silicon nitride particles to form a low melting temperature liquid phase which allows liquid phase sintering to occur and densification of the Si₃N₄. The highest flexural strength was 791(±20) MPa with 12 wt% additives sintered at 1780°C for 2 hours, comparable to the samples prepared by gas pressure sintering. Fracture toughness of all the specimens was higher than 7.2 MPa·m^1/2 as the sintering temperature was increased to 1810°C. Thermal conductivity was improved by prolonging the dwelling time and adopting the annealing process. The highest thermal conductivity of 74 W/(m∙K) was achieved with 9 wt% sintering additives sintered at 1810°C with 4 hours holding followed by postannealing.     

Effect of YF3 on densification behavior and thermal conductivity of AlN ceramics with Y2O3–YF3 additives under reducing atmosphere

The effect of yttrium fluoride (YF₃) on the densification behavior, microstructure, phase composition and thermal conductivity of aluminium nitride (AlN) ceramics with yttrium oxide (Y₂O₃) and YF₃ additives were studied. Since YF₃ provided liquid phases and promoted densification at a lower temperature, the sintering temperature required to reach the full density of AlN samples decreased with the increase in YF₃ content. Appropriate addition of YF₃ could improve the thermal conductivity of AlN ceramics, but the values of thermal conductivity decreased as YF₃ increased further. It is attributed to the ability of YF₃ to react with oxygen impurity was worse than that of Y₂O₃. Moreover, the reducing atmosphere significantly affected the phase composition, and the oxygen content in grain boundary phases decreased at 1750 °C and 1800 °C. Therefore, the proper proportion of Y₂O₃–YF₃ additives could simultaneously improve densification and the thermal conductivity of AlN samples at a low sintering temperature.     

AlN with high strength and high thermal conductivity based on an MCAS-Y2O3-YSZ multi-additive system

The additive composition of an AlN ceramic substrate material was optimized to achieve high strength and thermal conductivity. MgO-CaO-Al₂O₃-SiO₂ (MCAS) glass and Y₂O₃ were used as basic additives for improved sintering properties and thermal conductivity, thereby allowing for AlN to be sintered at a relatively low temperature of 1600 °C without pressurization. Yttria-stabilized zirconia (YSZ) was added (0–3 wt%) to further improve the strength of the AlN ceramic. YSZ and Y₂O₃ reacted with AlN to produce ZrN, Y₄Al₂O₉, and Y₃Al₅O₁₂ secondary phases. The formation of these yttrium aluminate phases improved the thermal conductivity by removing oxygen impurities, while ZrN formed at the AlN grain boundaries provided resistance to grain boundary fractures for improved strength. Overall, the AlN ceramic with 1 wt% MCAS, 3 wt% Y₂O₃, and 1 wt% YSZ exhibited excellent thermal and mechanical properties, including a thermal conductivity of 109 W/mK and flexural strength of 608 MPa.     

Effects of Y2O3/MgO ratio on mechanical properties and thermal conductivity of silicon nitride ceramics

In this work, the effects of Y₂O₃/MgO ratio on the densification behavior, phase transformation, microstructure evolution, mechanical properties, and thermal conductivity of Si₃N₄ ceramics were investigated. Densified samples with bimodal microstructure could be obtained by adjusting the ratio of Y₂O₃/MgO. It was found that a low Y₂O₃/MgO ratio facilitated the densification of Si₃N₄ ceramics while a high Y₂O₃/MgO ratio benefited the phase transformation of Si₃N₄ ceramics. Best mechanical properties (flexural strength of 875 MPa, and fracture toughness of 8.25 MPa·m^1/2, respectively) and optimal thermal conductivity of 98.04W/(m·K) were achieved in the sample fabricated with Y₂O₃/MgO ratio of 3:4 by sintering at 1900°C for 4 h.     

Microstructure and properties of porous SiC ceramics with AlN–RE2O3 (RE = Sc,Y, Lu) additives

The intrinsic microstructure and crystalline phases of porous SiC ceramics with 5 vol% AlN–RE₂O₃ (RE = Sc, Y, Lu) additives were characterized by high-resolution transmission microscopy with energy-dispersive spectroscopy and X-ray diffraction. The homophase (SiC/SiC) and heterophase (SiC/junction) boundaries were found to be clean; that is, amorphous films were not observed in the specimens. In addition, ScN, YN, and LuN were formed as secondary phases. The flexural strength and thermal conductivity of the ceramics were successfully tuned using different additive compositions. The flexural strength of the ceramics improved by a factor of ~3, from 11.7 MPa for the specimen containing Y₂O₃ to 34.2 MPa for that containing Sc₂O₃, owing to the formation of a wide necking area between SiC grains. For the same reason, the thermal conductivity improved by ~56%, from 9.2 W·m^?1·K^?1 for the specimen containing Lu₂O₃ to 14.4 W·m^?1·K^?1 for that containing Sc₂O₃.     

Direct bonding of silicon carbide ceramics sintered with yttria

SiC ceramics sintered with yttria were successfully joined without an interlayer by conventional hot pressing at lower temperatures (2000–2050 °C) compared to those of the sintering temperatures (2050–2200 °C). The joined SiC ceramics sintered with 2000 ppm Y₂O₃ showed almost the same thermal conductivity (˜198 Wm⁻¹ K⁻¹), fracture toughness (3.7 ± 0.2 MPa m^1/2), and hardness (23.4 ± 0.8 GPa) as those of the base material, as well as excellent flexural strength (449 MPa). In contrast, the joined SiC ceramics sintered with 4 wt% Y₂O₃ showed very high thermal conductivity (˜204 Wm⁻¹ K⁻¹) and excellent flexural strength (˜505 MPa). Approximately 16–22% decreases in strength compared to those of the base SC materials were observed in both joined ceramics, due to the segregation of liquid phase at the interface. This issue might be overcome by preparing well-polished and highly flat surfaces before joining.     

Effect of carbon content on electrical,thermal, and mechanical properties of porous SiC ceramics with B4C and C additives

The electrical, thermal, and mechanical properties of porous SiC ceramics with B₄C-C additives were investigated as functions of C content and sintering temperature. The electrical resistivity of porous SiC ceramics decreased with increases in C content and sintering temperature. A minimal electrical resistivity of 4.6 × 10^?2 Ω·cm was obtained in porous SiC ceramics with 1 wt% B₄C and 10 wt% C. The thermal conductivity and flexural strength increased with increasing sintering temperature and showed maxima at 4 wt% C addition when sintered at 2000 °C and 2100 °C. The thermal conductivity and flexural strength of porous SiC ceramics can be tuned independently from the porosity by controlling C content and sintering temperature. Typical electrical resistivity, thermal conductivity, and flexural strength of porous SiC ceramics with 1 wt% B₄C-4 wt% C sintered at 2100 °C were 1.3 × 10^?1 Ω·cm, 76.0 W/(m·K), and 110.3 MPa, respectively.     

Influence of Y2O3 on densification,flexural strength and heat shock resistance of cordierite-based composite ceramics

In order to fabricate a heat transfer ceramic-based pipeline for concentrated solar power, rare earth Y₂O₃ was utilized as a modifying agent to improve the physico-chemistry properties of the cordierite-based composite ceramics. The influences of the sintering temperature and Y₂O₃ additive on the densification, flexural strength, and thermostability were investigated. The research results indicate that the densification degree of the composite ceramics gradually increases with elevated temperature, and the initial sintering temperature decreases with the addition of Y₂O₃. In addition, the flexural strength and heat shock resistance of the ceramic materials were improved with the addition of Y₂O₃. In particular, a sample containing 7 wt% Y₂O₃ (sample E4) sintered at 1360 °C showed the best properties with a relative density of 92.49%, a flexural strength of 126.81 MPa, and strength loss rate of -7.74% after 30 heat shock cycles. X-ray diffraction and scanning electron microscopy analysis showed that parts of Y³⁺ ions dissolving into high-temperature liquid phases could reduce liquid viscosity to accelerate grain crystallization and pore elimination. The second phase of yttrium silicate properly impeded the generation of β-spodumene with lower strength during the heat shock process. Overall, a cordierite-based composite ceramic with low porosity was obtained with high mechanical strength and heat shock resistance and can be regarded as a highly potential material for solar heat transfer pipelines.     

Mechanical and thermal properties of silicon carbide ceramics with yttria–scandia–magnesia

Two different SiC ceramics with a new additive composition (1.87 wt% Y₂O₃–Sc₂O₃–MgO) were developed as matrix materials for fully ceramic microencapsulated fuels. The mechanical and thermal properties of the newly developed SiC ceramics with the new additive system were investigated. Powder mixtures prepared from the additives were sintered at 1850 °C under an applied pressure of 30 MPa for 2 h in an argon or nitrogen atmosphere. We observed that both samples could be sintered to ≥99.9% of the theoretical density. The SiC ceramic sintered in argon exhibited higher toughness and thermal conductivity and lower flexural strength than the sample sintered in nitrogen. The flexural strength, fracture toughness, Vickers hardness, and thermal conductivity values of the SiC ceramics sintered in nitrogen were 1077 ± 46 MPa, 4.3 ± 0.3 MPa·m^1/2, 25.4 ± 1.2 GPa, and 99 Wm⁻¹ K⁻¹ at room temperature, respectively.     

Fabrication of Al2O3/AlN composite ceramics with enhanced performance via a heterogeneous precipitation coating process

To improve the thermal and mechanical properties of Al₂O₃/AlN composite ceramics, a novel heterogeneous precipitation coating (HPC) approach was introduced into the fabrication of Al₂O₃/AlN ceramics. For this approach, Al₂O₃ and AlN powders were coated with a layer of amorphous Y₂O₃, with the coated Al₂O₃ and AlN powders found to favor the formation of an interconnected YAG second phase along the grain boundaries. The interconnected YAG phase was designed to act as a diffusion barrier layer to minimize the detrimental interdiffusion between Al₂O₃ and AlN particles. Compared with samples prepared by a conventional ball-milling method, the HPC Al₂O₃/AlN composites exhibited less AlON formation, a higher relative density, a smaller grain size and a more homogeneous microstructure. The thermal conductivity, bending strength, fracture toughness and Weibull modulus of the HPC Al₂O₃/AlN composite ceramics were found to reach 34.21 ± 0.34 W m⁻¹ K⁻¹, 475.61 ± 21.56 MPa, 5.53 ± 0.29 MPa m^1/2 and 25.61, respectively, which are much higher than those for the Al₂O₃ and Al₂O₃/AlN samples prepared by the conventional ball-milling method. These results suggest that HPC is a more effective technique for preparing Al₂O₃/AlN composites with enhanced thermal and mechanical properties, and is probably applicable to other composite material systems as well.     

Fabrication and properties of pressure-sintered reaction-bonded Si3N4 ceramics with addition of Eu2O3–MgO–Y2O3

Dense pressure-sintered reaction-bonded Si₃N₄ (PSRBSN) ceramics were obtained by a hot-press sintering method. Precursor Si powders were prepared with Eu₂O₃–MgO–Y₂O₃ sintering additive. The addition of Eu₂O₃–MgO–Y₂O₃ was shown to promote full nitridation of the Si powder. The nitrided Si₃N₄ particles had an equiaxial morphology, without whisker formation, after the Si powders doped with Eu₂O₃–MgO–Y₂O₃ were nitrided at 1400 °C for 2 h. After hot pressing, the relative density, Vickers hardness, flexural strength, and fracture toughness of the PSRBSN ceramics, with 5 wt% Eu₂O₃ doping, were 98.3 ± 0.2%, 17.8 ± 0.8 GPa, 697.0 ± 67.0 MPa, and 7.3 ± 0.3 MPa m^1/2, respectively. The thermal conductivity was 73.6 ± 0.2 W m^?1 K^?1, significantly higher than the counterpart without Eu₂O₃ doping, or with ZrO₂ doping by conventional methods.     

Effect of in-situ formed Y2O3 by metal hydride reduction reaction on thermal conductivity of β-Si3N4 ceramics

The effect of YH₂ on densification, microstructure, and thermal conductivity of Si₃N₄ ceramics were investigated by adjusting the amount of YH₂ in the range of 0–4 wt% using a two-step sintering method. Native SiO₂ was eliminated, and Y₂O₃ was in situ formed by a metal hydride reduction reaction, resulting in various Y₂O₃/SiO₂ ratios. Full densification of YH₂-doped samples could be achieved after sintering at 1900 °C for 4 h. The Y₂O₃/SiO₂ ratio had a significant influence on the composition of crystalline secondary phases. Besides, the increased Y₂O₃/SiO₂ ratio is conducive not only to the grain growth but also to the reduction of activity of SiO₂ in the liquid phase, resulting in enlarged purified grains, reduced volume fraction of intergranular phases and increased Si₃N₄-Si₃N₄ contiguity. Ultimately, the thermal conductivity increased by 29 % from 95.3 to 123.0 W m⁻¹ K⁻¹ after sintering at 1900 ℃ for 12 h by the substitution of Y₂O₃ with YH₂.     

Improved thermal conductivity of β-Si3N4 ceramics by lowering SiO2/Y2O3 ratio using YH2 as sintering additive

A two-step sintering process was conducted to produce β-Si₃N₄ ceramics with high thermal conductivity. During the first step, native SiO₂ was eliminated, and Y₂O₃ was in situ generated by a metal hydride reduction process, resulting in a high Y₂O₃/SiO₂ ratio. The substitution YH₂ for Y₂O₃ endow Si₃N₄ ceramics with an increase of 29% in thermal conductivity from 95.3 to 123 W m⁻¹ K⁻¹ after sintered at 1900°C for 12 hours despite an inferior sinterability. This was primarily attributed to the purified enlarged grains, devitrified grain boundary phase, and reduced lattice oxygen content in the YH₂-MgO-doped material.     

Effects of doping Al-metal powder on thermal,mechanical and dielectric properties of AlN ceramics

In this work, the influence of Al-metal powder addition upon that thermal, mechanical and dielectric properties of aluminium nitride (AlN) ceramic was studied. The findings show that adding Al-metal powder improves not only the mechanical and thermal properties of the AlN ceramic but also has no negative impact on its dielectric properties. Based on Y₂O₃ as sintering aid, the AlN ceramic with 1.0 wt% Al doping were 14.35% higher thermal conductivity, 11.73% higher flexural strength and 59.50% higher fracture toughness than those doped without Al, respectively. This study showed that the addition of Al-metal powder may favor the purifying of the AlN lattice and the formation of homogenous and isolated second phase, which would increase the AlN–AlN interfaces and improve the thermal conductivity. Furthermore, the grain boundaries of AlN ceramics might be strengthened by the isolated second phases due to the thermal mismatch between the second phases and AlN grains, thus strengthening and toughening the AlN ceramic doped with Al. However, the large additive amount of Al powder (>1.0 wt%) was not help the isolation and homogenization of the second phase, giving a deterioration in an AlN ceramic's mechanical and thermal properties. These results suggest that the introduction of an appropriate dose of aluminium metal powder is a simple method that can be used to improve the AlN ceramic's mechanical and thermal properties simultaneously.     

Effect of Sm2O3 on microstructure,thermal shock resistance and thermal conductivity of cordierite-mullite-corundum composite ceramics for solar heat transmission pipeline

Cordierite-mullite-corundum composite ceramics for solar heat transmission pipeline were fabricated via pressureless sintering at a low sintering temperature with added Sm₂O₃. The effects of Sm₂O₃ on sintering behaviors, mechanical property, phase transformation, microstructure, thermal shock resistance and thermal conductivity of the composite ceramics were investigated. TEM analysis results demonstrated that Sm³⁺ located in glass and grain boundaries to facilitate the densification via the liquid-phase sintering mechanism and improve bending strength by grain refinement, respectively. Proper addition (3 wt%) of Sm₂O₃ could promote the crystallization of cordierite, and improve thermal shock resistance of the composite ceramics with an increasing rate of 16.70% for bending strength after 30 thermal shock cycles (air cooling from 1100 °C to RT). The composite ceramics possessed a superior thermal shock resistance, where a large amount of particles were formed to suppress crack initiation and propagation during thermal shock. Cordierite-mullite-corundum composite ceramics with proper Sm₂O₃ addition (3 wt%) had a lower thermal conductivity than that of composite ceramics without Sm₂O₃ addition by strengthening the scattering of phonon, which could reduce the heat loss during solar heat transmission process.     

Electrical and Thermal Properties of SiC Ceramics Sintered with Yttria and Nitrides

The electrical and thermal properties of SiC ceramics containing 1 vol% nitrides (BN, AlN or TiN) were investigated with 2 vol% Y₂O₃ addition as a sintering additive. The AlN‐added SiC specimen exhibited an electrical resistivity (3.8 × 10¹ Ω·cm) that is larger by a factor of ~10² compared to that (1.3 × 10^?1 Ω·cm) of a baseline specimen sintered with Y₂O₃ only. On the other hand, BN‐ or TiN‐added SiC specimens exhibited resistivity that is lower than that of the baseline specimen by a factor of 10^?1. The addition of 1 vol% BN or AlN led to a decrease in the thermal conductivity of SiC from 178 W/m·K (baseline) to 99 W/m·K or 133 W/m·K, respectively. The electrical resistivity and thermal conductivity of the TiN‐added SiC specimen were 1.6 × 10^?2 Ω·cm and 211 W/m·K at room temperature, respectively. The present results suggest that the electrical and thermal properties of SiC ceramics are controllable by adding a small amount of nitrides.     

Pressureless sintered Al4SiC4 ceramics with Y2O3 addition

Highly densified Al₄SiC₄ ceramics with a relative density of 96.1% were prepared by pressureless sintering using 2 wt% Y₂O₃ as additives. The densification mechanism, phase composition, microstructures and mechanical properties of Al₄SiC₄ ceramics were investigated. Y₂O₃ in-situ reacted with the oxygen impurities in Al₄SiC₄ powder to form a yttrium aluminate liquid phase during sintering, which promoted the densification and anisotropic grain growth. The final Al₄SiC₄ ceramics were composed of equiaxed grains and columnar grains, and presented a bimodal grain distribution. The mechanical properties of the pressureless sintered Al₄SiC₄ ceramics were better than those reported for hot pressed Al₄SiC₄, including a flexural strength of 369 ± 24 MPa, fracture toughness of 4.8 ± 0.1 MPa m^1/2 and Vickers hardness of 11.3 ± 0.2 GPa. Pressureless sintering of Al₄SiC₄ ceramics is of great significance for the development and practical application of Al₄SiC₄ ceramic parts, especially with big size and complex shape.