不同填料增强顺丁橡胶性能对比研究

采用TG-DSC、RPA等手段研究了不同填料(纳米TiO2、纳米MgO、炭黑N220)对BR硫化特性、热稳定性、力学性能、动态力学性能等的影响。结果表明,BR/N220复合材料的ML、MH明显大于BR/MgO和BR/TiO2;纳米MgO和纳米TiO2可以抑制BR的热氧降解,提高BR的热稳定性;BR/MgO、BR/TiO2拉断伸长率大于BR/N220,而BR/N220的拉伸强度、撕裂强度、定伸应力和硬度更高。动态力学性能分析表明,BR/MgO复合材料的贮能模量G’和损耗因子tanδ大于BR/N220和BR/TiO2,出现较明显的"Payne效应"。     

烧结助剂添加量对微波烧结3Y-TZP/Al2O3复相陶瓷性能的影响

本文分别以TiO2和MgO纳米粉体为烧结助剂,采用微波烧结技术制备了3Y-TZP/Al2O3复相陶瓷.研究了烧结助剂含量对材料相组成、致密化及力学性能的影响,通过XRD分析了复相陶瓷中t-ZrO2相的相对量变化,并采用SEM观察了弯曲断裂断口形貌.结果表明:随烧结助剂添加量的增加,微波烧结复相陶瓷的致密度、硬度和弯曲强度均有所增加,均优于传统烧结性能,陶瓷颗粒更细.烧结助剂添加量为0.2wt％ MgO、0.4wt％ TiO2,在1300℃微波烧结30 min时试样的致密度为98.1％,显微硬度和抗弯强度分别达18.9 GPa和626 MPa.     

CMS和纳米TiO2对氧化铝陶瓷烧结的影响

选用CaO-MgO-SiO2(CMS)和纳米TiO2两种添加剂及其复合来降低氧化铝陶瓷的烧结温度、改善其烧结性能.讨论了烧结助剂配比和掺量、烧结温度对氧化铝陶瓷的相对密度、抗弯强度的影响,利用扫描电子显微镜观察了氧化铝陶瓷的显微结构.研究结果发现:CMS/TiO2质量比为1/1,(CMS+TiO2)质量分数为6%,烧结温度为1450 ℃时,氧化铝陶瓷相对密度为93.07 %,晶粒细小均匀、排列紧密、平均粒径3 μm,抗弯强度达到362.87 MPa.     

Al2TiO5添加量对MgO-Al2TiO5复合陶瓷烧结及抗热震性的影响

以纳米MgO粉为原料,选用以纳米Al2O3粉和纳米TiO2粉经1500℃保温3 h烧结制备的Al2TiO5为添加剂,采用固相烧结法经1500℃保温3 h制备了Al2TiO5质量分数分别为0、5%、10%和20%的MgO-Al2TiO5复合陶瓷,并采用XRD、SEM和EDS等研究了Al2TiO5添加量对MgO-Al2TiO5复合陶瓷烧结性能及抗热震性能的影响。结果表明:添加Al2TiO5有利于促进复合陶瓷的烧结,其体积密度和线收缩率随Al2TiO5添加量的增加而增大,当Al2TiO5添加量为20%(w)时,其体积密度和线收缩率分别为3.68 g·cm-3和22.07%;当Al2TiO5添加量为10%(w)时,其抗热震性能最佳。Al2TiO5位于方镁石晶粒交界处,抑制方镁石晶粒生长,阻碍裂纹扩展,使MgO-Al2TiO5复合陶瓷的抗热震性能得到改善。     

MgO-Al2O3-TiO2浇注料的组成、结构及性能

用XRD分析了MgO -Al2 O3-TiO2 系浇注料的物相组成 ,通过光学显微镜观察了材料的微观结构。结果表明 :MgO -Al2 O3-TiO2 浇注料经高温烧结后主要由方镁石和MgO·Al2 O3- 2MgO·TiO2 固溶体组成 ;加入TiO2 能显著促进MgO -Al2 O3质浇注料的烧结 ,气孔率降低 ,强度显著提高。     

MgO-TiO_2-La_2O_3系氧化铝陶瓷的力学性能及物相分析

采用MgO-TiO2-La2O3为烧结助剂,利用低温烧结技术制备95氧化铝瓷。研究了烧成温度和助剂含量对氧化铝陶瓷力学性能及物相组成的影响。结果表明:在MgO含量为1.5wt%,TiO2为1.0wt%,La2O3为2.5wt%,1500℃保温2h可得到抗弯强度和硬度分别为348.94MPa和79.6HRA的氧化铝陶瓷。     

纳米TiO2陶瓷无压烧结的主烧结曲线

采用纳米金红石相TiO2粉末在空气中进行烧结,用热膨胀仪记录恒定加热速率条件下的烧结过程,测量了烧结体密度,根据烧结3个阶段的全期烧结模型(combined-stage sintering model),建立TiO2主烧结曲线(master sintering curve).纳米TiO2主烧结曲线对烧结路径不敏感,烧结体的相对密度仅是时间和温度的函数,利用主烧结曲线得到的相对密度和Archimedes法实测的密度吻合,证明了主烧结曲线的有效性;根据纳米金红石的主烧结曲线,得到其在空气中的烧结激活能为105 kJ/mol;可以预测烧结收缩量和最终相对密度,准确描述烧结全程的烧结行为.     

纳米TiO_2表面接枝PAN及其对PP抗紫外老化性能的影响

采用细微乳液聚合法制备了基于共价键结合的纳米TiO2表面接枝聚丙烯腈(PAN)(纳米TiO2-g-PAN)复合抗紫外老化剂,将其与聚丙烯(PP)共混制备了PP/纳米TiO2-g-PAN复合材料。研究了纳米TiO2-g-PAN在PP中的分散情况及PP/纳米TiO2-g-PAN复合材料的抗紫外老化性能。傅立叶变换红外光谱、热失重、扫描电子显微镜和力学性能测试分析表明,PAN成功接枝到纳米TiO2表面,提高了纳米TiO2与PP的相容性及PP/纳米TiO2-gPAN复合材料的热稳定性能、力学性能和抗紫外老化性能。当纳米TiO2-g-PAN与PP配比为0.05时,PP/TiO2-gPAN复合材料的拉伸强度、冲击强度、拉伸强度保持率和冲击强度保持率分别为38.66 MPa,691.75 kJ/m2,63.49%和58.42%,综合力学性能最佳。     

纳米TiO2添加剂对Al2O3陶瓷微观结构与烧结性能的影响

用微米级和纳米级两种不同的TiO2作为烧结助剂,研究其对Al2O3陶瓷微观结构和烧结性能的影响.结果表明:纳米TiO2能更好的提高Al2O3陶瓷的烧结活性,降低烧结温度.当TiO2含量为2%时,在1 580℃烧结试样的显气孔率为0.54%;在1 650℃烧结试样的显气孔率为0.16%.纳米TiO2的加入改变了Al2O3陶瓷的微观结构,更有利于Al2O3陶瓷的烧结.     

纳米TiO2原位聚合改性聚氯乙烯研究

通过原位悬浮聚合将偶联剂KH-570包覆的纳米TiO2添加到聚氧乙烯(PVC)中对其进行改性。经改性纳米TiO2改性后,PVC的拉伸强度、冲击强度和维卡软化温度均有所提高,纳米TiO2占PVC质量为0.2%时,拉伸强度由60.7 MPa提高到66.8 MPa,改性纳米TiO2为0.5%,冲击强度由3.7 kJ/m2提高到5.85 kJ/m2,改性纳米TiO2占PVC质量为0.1%时,维卡软化温度由84℃提高至91℃;热重分析表明,改性纳米TiO2表面接枝了3.2%的偶联剂KH-570,聚合后纳米TiO2表面接枝了36%的PVC。比较了不同溶剂中偶联剂改性的纳米TiO2对PVC的改性效果,在甲苯中改性的纳米TiO2对维卡软化温度的提高最为明显,通过XRD分析可以发现甲苯中改性的纳米TiO2使PVC有了有序结构。     

SEDIMENTATION OF BINARY MIXTURES OF PARTICLES OF UNEQUAL DENSITIES AND OF DIFFERENT SIZES

A model is developed for the sedimentation from a suspension of two particle species of unequal densities and of different sizes. The composition and the thickness of various layers in the sediments are predicted using graphical and analytical methods. The model predictions were in excellent agreement with experimental results, when the particle size ratio was ≥ 108. When size ratio of the particles was 2.60 and 4.31 the agreement occurred in about 50 percent of the cases.     

COMPARISON OF METHODS OF ANALYSIS OF GYPSUM1

The different analytical methods proposed for the evaluation of gypsum have been subjected to an experimental test. A combination method, consisting of a fusion with KHCO₃ and determination of CaO by KMnO₄ titration, the SO₃ by Andrews method of titration of BaCrO₄ has been found to give very reliable results with the least consumption of time.     

氢气纯度分析方法准确性的探讨

ONACCURACYOFANALYSISOFOFHYDROGEN1前言我公司目前应用的氢气纯度分析方法有两种,一种是爆炸反应法,另一种是焦性没食子酸吸收法。几年来,人们对两种分析方法的准确性曾有过褒贬不一的评论。这里我们也谈谈自己粗浅的观点。2爆炸法测定氢气纯度一定量的氢气样品与适量的空气之均匀混合物因反应后生成液体水而引起气体体积减少,减少的体积等于参加反应气体体积之和。其中l／3为氧气,2／3为氢气。根据氢气取样量和反应前后混气体体积之差,以及氢气在反应中的体积比例关系,可计算出样品的氢气纯度。计算公式式中：A一混…     

骑式摩托车油箱喷涂工艺的改进

面对日益激烈的市场竞争,摩托车油箱外观质量越来越成为影响销售的因素之一。文章介绍了改进工艺后的油箱涂装,该涂装体系提高了油箱外观的丰满度,降低了油箱涂装的生产成本。     

HEASUREHENT OF INSTANTANEOUS RATES OF LOSS OF VOIATILE COMPOUNDS DURING DRYING OF DROPS

A novel technique serves to monitor instantaneous rates of loss of a volatile solute from a suspended drop during drying. A highly sensitive electron capture detector is used to monitor concentrations of SF6 released into a flowing gas stream from a suspended, drying drop. Simultaneously, the appearance and morphological development of the drop are monitored with a video camera. This provides the wherewithal of relating instantaneous rates of loss of the volatile solute to particular events during the development of particle morphology.

Initial experiments have been carried out with drops of aqueous solutions of glucose, sucrose, maltodextrin and coffee extract. The results clearly display the onset of the volatiles-retentive selective diffusion phenomenon. There is also substantial loss of the volatile component later in the drying process, when the drops undergo repeated ex ansion, bursting and cratering due to the formation of internaf bubbles. These experiments appear to be the first quantitative demonstration of major losses accompanying changes in drop morphology.     

用两个形状指数表征粉煤灰颗粒形貌的研究

引用两个形状指数表征颗粒形状的概念,即先将颗粒形状近似为椭圆,再将椭圆图像分离:以圆为基准的颗粒宏观形状指数δ;以光滑椭圆为基准的颗粒轮廓凹凸度,即微观形状指数ζ。分析和发展了近似椭圆模型。并运用图像分析仪对粉煤灰、水泥样品进行实验。结果表明,粉煤灰颗粒的两个形状指数δ和ζ都大于水泥颗粒。证明粉煤灰颗粒的球形度、表面光滑度优于水泥,而且,随着粒径增大,δ和ζ呈下降趋势,表明磨制颗粒越粗。(?)粒形状越不规则。文中还运用近似椭圆模型再现了颗粒的模拟图像。     

典型煤碳燃烧特性研究和数值模拟

本文以三种典型煤的碳燃烧为研究对象，分别采用简单一维沉降燃烧方式和等温加热燃烧方式，实验研究了煤在快速加热条件下，其碳的初期和中，后期燃烧过程。以实验为基础，建立了煤的碳燃烧模型，变工况数值模拟了煤的碳燃烧过程，揭示了煤不同条件下的单颗粒碳燃烧特性。     

茶多酚提取方法进展

本文综述了国内外现有茶多酚提取方法的现状以及近期的研究进展，并对其优缺点进行了评价。这将有助于中低档茶的综合利用和茶多酚的进一步开发应用。     

卫生陶瓷烧成用窑炉发展之我见

归纳了当今卫生陶瓷工业的发展现状和水平 ,对窑炉产业提出了的新要求 ,分析了某一新型窑炉的特点 ,对发展我国陶瓷窑炉产业提出了建议     

ANALYSIS OF RECENT MEASUREMENTS OF THE VISCOSITY OF GLASSES

Viscosity of Simple Soda-Silicate 500° to 1400°C Comparison of the results given by English with those of Washburn, Shelton and Libman, indicates a discrepancy in the absolute values of log₁₀ viscosity amounting to 0.6, those of Washburn et al., being relatively too high. If correction for this is made, the isothermal curves of log₁₀ viscosity as a function of soda content are smooth up to 50% Na₂O, showing no inflection. The observations as a function of temperature T are all represented within accidental error by an equation of the type where all three constants vary regularly with the composition. Change of Viscosity of Glass (6SiO₂, 2Na₂O) due to Molecular Substitution of CaO, MgO and Al₂O₃ for Na₂O The effect is clearly brought out by plotting (from the results of English) the change of log₁₀η due to the substitution as a function of temperature. The curves each show a sharp bend at a temperature between 840° and 1050°C, which is designated the aggregation temperature T_a. If we divide these curves by the corresponding percentage substituted, we get curves for each oxide which are straight and parallel below the aggregation temperatures, the slopes (increase of change of log₁₀η per 100°C) being −0.056 (CaO), −0.055 (MgO), −0.018 (A1₂O₃) per per cent oxide substituted. For substitution of 1/2 molecule the slopes are −0.325 (CaO), −0.23 (MgO) and −0.18 (Al₂O₃) per 100°. At the aggregation temperature the change of log₁₀η per per cent is a minimum, 0.03 to 0.06 for CaO, 0.12 for MgO, 0.07 for Al₂O₃. Evidence of Aggregation in Glasses, from viscosity Measurements The sharp bends in the plots of change of log₁₀η due to substitution of an oxide for Na₂O, suggest the beginning of molecular aggregation at these temperatures. These aggregation temperatures are close to the devitrification temperatures, but the effect on the viscosity curves cannot be due to actual devitrification since it does not change with time. Taking the aggregation temperatures as equal to devitrification temperatures, additional isotherms are roughly sketched into the equilibrium triangle of the system Na₂O-CaO-SiO₂. Change of Viscosity of Glass (4SiO₂, 2Na₂O) due to of Substitution of B₂O₃ for SiO₂ The change of log₁₀η (from the results of English) is plotted as a function of temperature, and also the change of log₁₀η per per cent B₂O₃. The curves are more complex than for the substitution for Na₂O.