Methanol‐Tolerant Heterogeneous PdCo@PdPt/C Electrocatalyst for the Oxygen Reduction Reaction

We have prepared carbon‐supported nanoparticles with the heterogeneous structure of a PdPt shell on a PdCo core which are effective for the oxygen reduction reaction (ORR) in the presence of methanol. The preparation was based on the galvanic replacement reaction between PdCo/C nanoparticles and PtCl₄^2–, a method of general utility which can be extended to the preparation of other core‐shell electrocatalysts. The heterogeneous PdCo‐core and PtPd‐shell architecture was confirmed by multiple techniques including high resolution transmission electron microscopy, energy dispersive X‐ray spectroscopy, powder X‐ray diffraction and X‐ray photoelectron spectroscopy. The activity of the PdCo@PdPt/C catalyst in ORR was evaluated in acidic solutions both with and without methanol (0.1 M). The results showed four to sixfold increases in activity over a standard Pt/C catalyst with no apparent loss of catalyst stability. It is inferred that the strain effect from the lattice mismatch between the shell and core components is the major contributor for the enhancement of ORR activity and selectivity.     

Nano-stuctured Pt-Fe/C as cathode catalyst in direct methanol fuel cell

Pt-Fe/C catalysts were prepared by a modified polyol synthesis method in an ethylene glycol (EG) solution, and then were heat-treated under H₂/Ar (10 vol.%) at moderate temperature (300 °C, Pt-Fe/C300) or high temperature (900 °C, Pt-Fe/C900). As comparison, Pt-Fe/C alloy catalyst was prepared by a two-step method (Pt-Fe/C900B). X-ray diffraction (XRD) and transmission electron microscopy (TEM) images show that particles size of the catalyst increases with the increase of treatment temperatures. Pt-Fe/C300 catalyst has a mean particle size of 2.8 nm (XRD), 3.6 nm (TEM) and some Pt-Fe alloy was partly formed in this sample. Pt-Fe/C900B catalyst has the biggest particle size of 6.2 nm (XRD) and the best Pt-Fe alloy form. Cyclicvoltammetry (CV) shows that Pt-Fe/C300 has larger electrochemical surface area than other Pt-Fe/C and the highest utilization ratio of 76% among these Pt-based catalysts. Rotating disk electrode (RDE) cathodic curves show that Pt-Fe/C300 has the highest oxygen reduction reaction (ORR) mass activity (MA) and specific activity (SA), as compared with Pt/C catalyst in 1.0 M HClO₄. However, Pt-Fe/C catalyst does not appears to be a more active catalyst than Pt/C for ORR in 1.0 M HClO₄ + 0.1 M CH₃OH. Pt-Fe/C300 exhibits higher ORR activity and better performance than other Pt-Fe/C or Pt/C catalysts when employed for cathode in direct methanol single cell test, the enhancement of the cell performance is logically attributed to its higher ORR activity, which is probably attributed to more Pt⁰ species existing and Fe ion corrosion from the catalyst.     

Preparation of high loading Pt nanoparticles on ordered mesoporous carbon with a controlled Pt size and its effects on oxygen reduction and methanol oxidation reactions

A series of ordered mesoporous carbon (OMC) supported Pt (Pt/OMC) catalysts with a controlled Pt size from 2.7 to 6.7 nm at high Pt loading around 60 wt.% have been prepared and their electrocatalytic activities for the electrode reactions relevant to the direct methanol fuel cells have been investigated. The Pt/OMC catalysts with a high dispersion (Pt size around 3 nm) could be prepared by the use of a modified, sequential impregnation–reduction method. The Pt/OMC catalysts containing larger Pt particles were obtained by increasing reduction temperature under hydrogen flow and Pt loading, and by performing impregnation–reduction in a single cycle. The oxygen reduction reaction (ORR) and methanol oxidation reaction (MOR) activities of Pt/OMC catalysts as a function of Pt size were investigated at room temperature in 0.1 M HClO₄ and (0.1 M HClO₄ + 0.5 M methanol), respectively. The specific activity of Pt/OMC for ORR steeply increased up to 3.3 nm and became independent of Pt size from 3.3 to 6.7 nm, and the mass activity curve exhibited maximum activity at 3.3 nm. The MOR activity of Pt/OMC also exhibited the similar trend with the ORR activity, as the maximum of mass activity was also found at 3.3 nm. The results of the present work indicate that the Pt catalysts of ca. 3 nm is an optimum particle size for both ORR and MOR, and this information may be translated into design of high performance membrane electrode assembly.     

Catalysts for Direct Methanol Fuel Cells

The activity of in house prepared carbon-supported Pt-Ru catalysts for methanol oxidation and carbon-supported RuSe for the oxygen reduction reaction in direct methanol fuel cells (DMFCs) was investigated. The composition of Pt-Ru/C was varied both in terms of weight loading (ratio of total metal content to carbon) as well as the ratio of Pt to Ru. The measurements were carried out in a half cell arrangement in sulphuric acid at various temperatures. The weight loading and ratio of Pt to Ru were varied in order to find out the optimum weight loading of precious metal and the temperature dependence of Pt to Ru ratio on methanol oxidation reaction. It has been found that there exists an optimum in the weight loading at 60 wt.% for carbon-supported Pt-Ru catalyst towards its maximum mass activity. While 1:1 Pt to Ru ratio exhibits a higher activity than 3:2 Pt:Ru above 60 °C, 3:2 ratio exhibits a higher activity at lower temperature. It has been observed that RuSe is inactive towards methanol and it is realised that RuSe is a potential candidate as methanol tolerant oxygen reduction catalyst. The activity of carbon supported RuSe for oxygen reduction reaction (ORR) was tested in sulphuric acid in the presence of methanol. Even though the mass specific activity of the RuSe catalyst is somewhat lower than that of Pt/C, the surface activity of carbon-supported RuSe is superior than that of carbon supported Pt which indicate the unfavourable size distribution of RuSe/C catalyst.     

High Oxygen‐Reduction‐Activity and Methanol‐Tolerance Cathode Catalyst Cu/PtFe/CNTs for Direct Methanol Fuel Cells

A novel nanocomposite Cu/PtFe/carbon nanotubes (CNTs) was designed, prepared and examined as a cathode catalyst for direct methanol fuel cells (DMFCs). The effects of Fe and Cu on oxygen reduction reaction (ORR) activity and methanol tolerance were investigated by varying their amounts or their configurations in the nanocomposite. The experimental results show that PtFe alloy on CNTs could not enhance methanol tolerance, but could improve the ORR activity. Cu was deposited on PtFe/CNTs to obtain better methanol tolerance. The optimum molar ratio of Cu/Pt/Fe in Cu/PtFe/CNTs is 2.1:1:0.7. After 500 cycles in 1 M HClO₄ solution, the Cu/PtFe/CNTs catalyst is fairly stable with 92% of its original ORR activity and 89.6% of its original electrochemical active surface areas (EAS) maintained.     

Highly Durable Platinum based Cathode Electrocatalysts for PEMFC Application using Oxygen and Nitrogen Functional Groups Attached Nanocarbon Supports

The combined effect of oxygen and nitrogen functional groups on highly crystalline carbon supports like multiwalled carbon nanotubes (MWCNT) and MWCNT‐few layer graphene hybrid structures (MWCNT+FLG) have been investigated towards oxygen reduction reaction (ORR) performance and carbon corrosion durability in polymer electrolyte membrane fuel cell (PEMFC) applications. The pristine carbon supports were modified with oxygen and nitrogen functionalities by treating with concentrated mineral acids and subsequent nitrogen plasma treatment assisted with R.F. magnetron sputtering. Pt nanoparticles were dispersed over these chemically modified carbon supports by polyol reduction method. The physicochemical properties of as synthesized electrocatalysts were studied by different techniques such as XRD, TEM, FTIR, Raman and XPS. Electrochemical properties were investigated by cyclic voltammetry and linear sweep voltammetry in 0.1M HClO₄ medium. Compared to commercial Pt/C catalysts, durability show ∼30 % enhancement for the as prepared electrocatalysts due to the presence of large amount of pyrrolic nitrogen and highly oriented graphitic nature of the catalyst supports. The ORR performance were comparable with Pt/C (TEC10E30E) in terms of MSA, 259, 270, 252 A g⁻¹ for Pt/C, Pt/N‐f‐MWCNT, Pt/N‐f‐(MWCNT+FLG) respectively.     

Dependences of the Oxygen Reduction Reaction Activity of Pd–Co/C and Pd–Ni/C Alloy Electrocatalysts on the Nanoparticle Size and Lattice Constant

Carbon-supported Pd-based binary alloy electrocatalysts (Pd–Co and Pd–Ni) with different particle sizes for polymer electrolyte fuel cells were prepared by a NaBH₄ reduction method and investigated to examine effects of the size and lattice constant of the Pd alloy nanoparticles on the oxygen reduction reaction (ORR) activity. The particle size and lattice constant were controlled in the wide ranges 4.2–12.1 and 0.3802–0.3948 nm, respectively by heating the catalysts in specific atmospheres. The alloy structures were characterized by X-ray diffraction, transmission electron microscopy and X-ray absorption fine structure. The electrochemical tests of the Pd–Co/C and Pd–Ni/C catalysts were performed by cyclic voltammetry and rotating disk electrode in 0.1 M HClO₄. Nearly linear relationship between the lattice constant and nanoparticle size was observed with the Pd–Co and Pd–Ni nanoparticles. The nanoparticle sizes and lattice constants of the Pd–Co/C and Pd–Ni/C electrocatalysts, which influence the Pd d-band center, showed positive and inverse relations with the ORR specific activities, respectively. The mass activities of the Pd–Co/C and Pd–Ni/C electrocatalysts showed an increasing trend with the lattice expansion.     

Synthesis, characterization and electrocatalytic behaviour of non-alloyed PtCr methanol tolerant nanoelectrocatalysts for the oxygen reduction reaction (ORR)

In order to point out the effect of the second metal in platinum-based catalysts, a synthesis method by colloidal route derived from that of Bönnemann was used to prepare non-alloyed Pt_1−xCr_x/C electrocatalysts active towards the oxygen reduction reaction (ORR). The non-alloyed character of the catalysts was showed by XRD analysis. The Pt/Cr electrocatalyst having an nominal atomic ratio, as determined by EDX then corresponding to bulk composition and not surface composition, close to (0.8:0.2) showed higher activity for ORR in methanol-free oxygen saturated electrolyte, whereas the catalyst having an atomic ratio of (0.7:0.3) displayed higher activity for ORR at low overpotentials in saturated oxygen electrolyte containing 0.1 M methanol.Correlation of XRD and electrochemical results allows us to point out the effect of electronic interactions in catalyst activity towards ORR. It was also shown that adding chromium to platinum does not alter the reaction mechanism of oxygen reduction, and that in presence of low methanol concentration, the ORR occurs via the four-electron process according to the same mechanism as in methanol-free solution.     

Electro-reduction of oxygen and electro-oxidation of methanol at Pd monolayer-modified macroporous Pt electrode

With polystyrene latex spheres self-assembled on indium tin oxide-coated glass electrode as templates, highly ordered macroporous Pt was prepared by electrochemical deposition. Then, the macroporous Pt was modified by Pd monolayer involving the galvanic displacement of Cu monolayer formed by under-potential deposition on macroporous Pt. Electrocatalytic properties of the Pd-modified macroporous Pt electrode for oxygen reduction were investigated by cyclic voltammetry and chronoamperometry in O₂-saturated solution containing 0.1 M HClO₄. Methanol electro-oxidation on the Pd-modified macroporous Pt surfaces in 0.5 M H₂SO₄ containing 1 M CH₃OH was studied by cyclic voltammetry. The corresponding results showed that Pd-modified macroporous Pt electrode had negative catalytic activity for methanol oxidation in compared with macroporous Pt. However, Pd-modified macroporous Pt electrode had positive electrocatalytic activity to O₂ reduction.     

Study of Methanol‐tolerant Oxygen Reduction Reaction at Pt–Bi/C Bimetallic Nanostructured Catalysts

The nanostructured platinum–bismuth catalysts supported on carbon (Pt₃Bi/C, PtBi/C and PtBi₃/C) were synthesised by reducing the aqueous metal ions using sodium borohydride (NaBH₄) in presence of a microemulsion. The amount of metal loading on carbon support was found to be 10 wt.‐%. The catalyst materials were characterised by X‐ray diffraction (XRD), X‐ray fluorescence (XRF), transmission electron microscope (TEM) and electroanalytical techniques. The Pt₃Bi/C, PtBi/C and PtBi₃/C catalysts showed higher methanol tolerance, catalytic activity for oxygen reduction reaction (ORR) than Pt/C of same metal loading. The electrochemical stability of these nano‐sized catalyst materials for methanol tolerance was investigated by repetitive cycling in the potential range of –250 to 150 mV_MSE. Bi presents an interesting system to have a control over the activity of the surface for MOR and ORR. All Pt–Bi/C catalysts exhibited higher mass activities for oxygen reduction (1–1.5 times) than Pt/C. It was found that PtBi/C catalyst exhibits better methanol‐tolerance than the other catalysts.     

Properties of Pt/C catalyst modified by chemical vapor deposition of Cr as a cathode of phosphoric acid fuel cell

Cr-modified Pt/C catalysts were prepared by the chemical vapour deposition (CVD) of Cr on Pt/C, and their performance as a cathode of phosphoric acid fuel cell (PAFC) was compared with the case of catalysts containing Cr added by impregnation (IMP).The catalyst prepared by CVD showed a higher activity for oxygen reduction reaction (ORR) than one prepared by IMP. There was an optimum amount of Cr that yielded the maximum mass activity of the catalyst because the gain in the intrinsic activity due to the promotional effect of Cr was counterbalanced by the loss of exposed Pt surface area as a result of the Cr introduction. Nevertheless, the activity increase at the optimum amount of Cr was greater for the CVD catalyst than for the IMP catalyst. Also, the optimum amount of Cr to yield the maximum activity was smaller for the former catalyst [Cr/Pt]_CVD = 0.6, than for the latter, [Cr/Pt]_IMP = 1.0.The enhancement of the Pt catalyst activity by Cr addition is attributed to two factors: changes in the surface Pt-Pt spacing and the electronic modification of the Pt surface. The formation of a Pt-Cr alloy, as confirmed by X-ray diffraction, decreased the lattice parameter of Pt, which was beneficial to the catalyst activity for ORR. X-ray photoelectron spectroscopy results showed that the binding energies of Pt electrons were shifted to higher energies due to Cr modification. Accordingly, the electron density of Pt was lowered and the Pt-O bond became weak on the Cr-modified catalysts, which was also beneficial to the catalyst activity for ORR.The promotion of oxygen reduction on Cr-modified catalysts was confirmed by measuring the cyclic voltammograms of the catalysts. All the above changes were made more effectively for catalysts prepared by CVD than for those prepared by IMP because the former method allowed Cr to interact more closely with the Pt surface than the latter, which was demonstrated by the characterization of catalysts in this study.     

Electrochemical and structural characterization of carbon-supported Pt-Pd bimetallic electrocatalysts prepared by electroless deposition

Electrochemical and structural characteristics of various Pt-Pd/C bimetallic catalysts prepared by electroless deposition (ED) methods have been investigated. Structural analysis was conducted by X-ray diffraction spectroscopy, X-ray photoelectron spectroscopy, scanning transmission electron microscopy, and energy dispersive X-ray spectroscopy (EDS). Monometallic Pt or Pd particles were not detected by EDS, indicating the ED methodology formed only bimetallic particles. The size of the Pt-Pd bimetallic particles was smaller than those of a commercially available Pt/C catalyst. The morphology of the Pt on Pd/C catalysts was identified and corresponded to Pd particles partially encapsulated by Pt.The electrochemical characteristics of the lowest Pd loading catalyst (7.0% Pt on 0.5% Pd/C) for the oxygen reduction reaction (ORR) have been investigated by the rotating ring disk electrode technique. The electrochemical activity was equal or lower than the commercially available Pt/C catalyst; however, the amount of hydrogen peroxide observed at the ring was reduced by the Pd, suggesting that such a catalyst has the potential to decrease ionomer degradation in applications. The Pt on Pd/C catalysts also show a higher tolerance to ripening induced by potential cycling. Therefore, catalyst suitability cannot be judged solely by its initial performance; information related to specific degradation mechanisms is also needed for a more complete assessment.     

Ordered mesoporous Fe (or Co)–N–graphitic carbons as excellent non-precious-metal electrocatalysts for oxygen reduction

Novel mesoporous Fe (or Co)–N_x–C non-precious-metal catalysts (NPMCs) have been fabricated by a simple nanocasting-pyrolysis method using 1,10-phenanthroline metal chelates as the precursors. Owing to the ordered hexagonal mesostructures, appropriate surface area, large-pore channels, and well-distributed metal–N_x moieties embedded within the graphitic carbon backbones, the prepared metal–N_x–C materials exhibit excellent catalytic activity for oxygen reduction reaction (ORR) in both alkaline and acidic media. The prepared Fe–N_x–C materials, when prepared with an optimized catalyst loading on the electrode, exhibit more positive ORR onset-potential and half-wave potential (E_1/2) than commercial Pt/C catalysts and the previously reported NPMCs in 0.1 M KOH electrolyte. They also have the comparable ORR onset-potential and current densities to Pt/C electrode in 0.1 M HClO₄ electrolyte. Moreover, ORR over mesoporous Fe–N_x–C was found to proceed by the direct four-electron mechanism with high selectivity in both electrolytes. The mesoporous Fe–N_x–C materials demonstrated higher ORR catalytic activity compared to the NPMCs made by alternative methods. Analysis of the catalytic behavior, structure and nature of surface species of N_x–C materials allows us to ascribe the origin of the excellent ORR catalytic activity of mesoporous Fe (or Co)–N_x–C in both electrolytes to Fe (or Co)–N_x moieties embedded within the graphitic carbon frameworks.     

Combinatorial Search for Quaternary Methanol Tolerant Oxygen Electro‐Reduction Catalyst

A combinatorial library containing 645 different compositions was synthesised and characterised for methanol tolerant oxygen electro‐reduction reaction (ORR) catalytic performance. The library was composed of compositions involving between 1 and 4 metals among Pt, Ru, Fe, Mo and Se. In an optical screening test, Pt(50)Ru(10)Fe(20)Se(10) composition exhibited the highest ORR activity in the presence of methanol. This composition was further investigated by synthesis and characterisation of a powder version catalyst [Pt(50)Ru(10)Fe(20)Se(10)/C]. At 0.85 V [vs. reversible hydrogen electrode (RHE)] in the absence of methanol, the Pt/C catalyst exhibited higher ORR current (0.0990 mA) than the Pt(50)Ru(10)Fe(20)Se(10)/C catalyst (0.0902 mA). But much higher specific activity (12.7 μA cm_pt^–2) was observed in the Pt(50)Ru(10)Fe(20)Se(10)/C catalyst than for the Pt/C catalyst 6.51 μA cm_pt^–2). In the presence of methanol, the ORR current decreased by 0.0343 and 0.247 mA for the Pt(50)Ru(10)Fe(20)Se(10)/C and Pt/C catalysts, respectively, which proved the excellent methanol tolerance of the Pt(50)Ru(10)Fe(20)Se(10)/C catalyst.     

Oxygen reduction activity of Pt and Pt-Mn-Co electrocatalysts sputtered on nano-structured thin film support

We report on extensive measurements of oxygen reduction activity of Pt and Pt-Co-Mn electrocatalysts using the rotating ring-disk electrode (RRDE) method. The electrocatalysts were prepared by sputtering from Pt or Pt, Co and Mn targets onto 3M's nano-structured thin film support (NSTF) structures. The area specific activity of Pt/NSTF, measured in 0.1 M HClO₄ and at room temperature, is similar to that of bulk Pt. The area specific measurements show a 20 mV reduction in the Pt-Co-Mn/NSTF overpotential compared to Pt/NSTF. The corresponding kinetic gain in the area specific activity of the ternary alloy is about a factor of two. This ORR enhancement factor observed in the ternary Pt-Co-Mn/NSTF by RRDE measurements is similar to the results obtained in 50 cm² H₂/air fuel cells.     

Characterization of methanol-tolerant Pd–WO3 and Pd–SnO2 electrocatalysts for the oxygen reduction reaction in direct methanol fuel cells

Palladium (Pd) catalysts containing nanosized metal oxides, tungsten oxide (WO₃) and tin oxide (SnO₂), supported on carbon black (Pd–MO_x/C) were synthesized, and the effect of the metal oxide on the oxygen reduction reaction (ORR) in a direct methanol fuel cell (DMFC) was investigated. The SEM images showed that the Pd nanoparticles were highly dispersed on the carbon black, and the metal oxide particles were also distributed well. Pd/C and Pd–WO₃/C catalysts as cathode materials for the ORR in DMFCs showed activity similar to or better than that of Pt/C, whereas Pd–SnO₂/C showed no improvement in catalytic activity.     

Pt decorating of PdNi/C as electrocatalysts for oxygen reduction

A low-cost and high performance catalyst consisting of Pt decorating PdNi/C (Pt-PdNi/C) for oxygen reduction is prepared by a two-stage route. The characterization techniques considered are X-ray diffraction (XRD), transmission electron microscopy (TEM) and energy dispersive X-ray analysis (EDX) technique. The results show that the Pt-PdNi/C catalyst has an average diameter of ca. 5 nm. The electrochemical activity for the ORR is evaluated from steady state polarization measurements, which are carried out in an ultra-thin layer rotating disk electrode (RDE). The RDE tests show that the Pt-PdNi/C catalyst has the highest ORR activity compared to pure Pt/C, Pd/C and PdNi/C catalysts. High electrocatalytic activities could be attributed to the synergistic effect between Pt and PdNi.     

Enhancement of oxygen reduction activity by sequential impregnation of Pt and Pd on carbon support

Two Pd-based PtPd bimetallic catalysts (mole ratio of Pt to Pd=1: 18) were prepared by co-impregnation (Pt-Pd/C) and sequential impregnation of Pt on Pd/C [Pt(Pd/C)] for the application to oxygen reduction reaction (ORR). The prepared bimetallic catalysts had lower ORR activities than Pt/C, while they showed largely enhanced activity compared to Pd/C. In particular, the extent of enhancement was found to be dependent on the surface composition. The observed mass and specific activities of Pt(Pd/C) were more than two times higher than those of Pt-Pd/C. The superior activity of Pt(Pd/C) observed from the performed studies was attributed to its Pt-rich surface.     

Activity,selectivity, and methanol tolerance of novel carbon-supported Pt and Pt<Subscript>3</Subscript>Me (Me = Ni,Co) cathode catalysts

The activity, selectivity, and methanol tolerance of novel, carbon supported high-metal loading (40 wt.%) Pt/C and Pt₃Me/C (Me = Ni, Co) catalysts for the O₂ reduction reaction (ORR) were evaluated in model studies under defined mass transport and diffusion conditions, by rotating (ring) disk and by differential electrochemical mass spectrometry. The catalysts were synthesized by the organometallic route, via deposition of pre-formed Pt and Pt₃Me pre-cursors followed by their decomposition into metal nanoparticles. Characteristic properties such as particle sizes, particle composition and phase formation, and active surface area, were determined by transmission electron microscopy, energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. For comparison, commercial Pt/C catalysts (20 and 40 wt.%, E-Tek, Somerset, NJ, USA) were investigated as well, allowing to evaluate Pt loading effects and, by comparison with the pre-cursor-based catalyst with their much smaller particle sizes (1.7 nm diameter), also particle size effects. Kinetic parameters for the ORR were evaluated; the ORR activities of the bimetallic catalysts and of the synthesized Pt/C catalyst were comparable and similar to that of the high-loading commercial Pt/C catalyst; at typical cathode operation potentials H₂O₂ formation is negligible for the synthesized catalysts. Due to their lower methanol oxidation activity the bimetallic catalysts show an improved methanol tolerance compared to the commercial Pt/C catalysts. The results indicate that the use of very small particle sizes is a possible way to achieve reasonably good ORR activities at an improved methanol tolerance at DMFC cathode relevant conditions.     

Oxygen reduction at Pt and Pt70Ni30 in H2SO4/CH3OH solution

The electrochemical oxygen reduction reaction (ORR) was studied at Pt and Pt alloyed with 30 atom% Ni in 1 M H₂SO₄ and in 1 M H₂SO₄/0.5 M CH₃OH by means of rotating disc electrode. In pure sulphuric acid, the overpotential of ORR at 1 mA cm⁻² is about 80 mV lower at Pt₇₀Ni₃₀ than at pure Pt. It was found that in methanol containing electrolyte solution the onset potential for oxygen reduction at PtNi is shifted to more positive potentials and the alloy catalyst has an 11 times higher limiting current density for oxygen reduction than Pt. Thus, PtNi as cathode catalyst should have a higher methanol tolerance for fuel cell applications. On the other hand, no significant differences in the methanol oxidation on both electrodes was found using cycling voltammetry, especially regarding the onset potential for methanol oxidation. During all the measurements no significant electrochemical activity loss was observed at Pt_0.7Ni_0.3. Ex-situ XPS investigations before and after the electrochemical experiments have revealed Pt enrichment in the first surface layers of the PtNi.