γ-TiAl合金表面Al2O3/Al复合涂层的抗高温熔盐腐蚀性能研究

采用磁控溅射技术于γ-TiAl合金表面制备Al₂O₃/Al复合涂层。在850 °C下、 100 wt.% Na₂SO₄熔盐中观测Al₂O₃/Al复合涂层的高温腐蚀行为。结果表明,Al₂O₃/Al复合涂层具备由Al₂O₃表层、富Al中间层以及互扩散层组成的梯度结构,因而有效地提高了基体γ-TiAl合金的抗高温腐蚀性能。在腐蚀实验后,涂层试样表面相结构为Al₂O₃,TiO₂和TiAl₃。致密的Al₂O₃/Al复合涂层有效地抑制了O_2-,S_-和Na₊对基体γ-TiAl合金的侵蚀。并且,Al₂O₃/Al复合涂层的梯度结构亦使其表现出了优异的抗开裂和抗剥落性能。     

激光熔覆纳米SiC增强Ni基合金涂层的组织与高温抗氧化性能

目的揭示添加纳米粉体对激光熔覆涂层高温防护性能的影响。方法以NiCoCrAlY合金粉末为熔覆材料,添加纳米SiC粉体,在GH4037合金表面激光熔覆纳米SiC增强Ni基合金涂层,对熔覆层表面及界面区进行显微组织分析,并进行1070℃下的高温抗氧化性实验。结果加入纳米SiC粉体的激光熔覆涂层组织明显细化,界面区未出现明显缺陷,其高温氧化速率远远低于未加纳米粉体的涂层,氧化膜致密,抗剥落能力显著增强。结论添加适量纳米SiC粉体对Ni基合金激光熔覆层的组织具有明显细化作用,对界面区裂纹的产生有一定的抑制作用,使得熔覆层的高温抗氧化性能显著提高。     

基于磁过滤技术的热障涂层表面Al2O3 覆盖层抗CMAS腐蚀性能

为了提高热障涂层（TBC）的抗沉积物（主要成分为CaO、MgO、Al₂O₃和SiO₂,简称CMAS）腐蚀性能,采用磁过滤阴极真空电弧（FCVA）技术在TBC表面上制备了致密的Al₂O₃覆盖层,比较和分析了Al₂O₃改性TBC和沉积态TBC的润湿行为和抗CMAS腐蚀性能。结果表明：使用FCVA技术制备Al₂O₃覆盖层的过程对7%（质量分数）氧化钇稳定的氧化锆（7YSZ）相的结构无明显影响,且经Al₂O₃改性的TBC综合性能均优于沉积态TBC。在1250 ℃、CMAS腐蚀条件下,Al₂O₃覆盖层有效地限制了熔融CMAS在TBC表面上的扩散行为。同时,Al₂O₃填充了7YSZ柱状晶之间的间隔并且阻碍了熔融CMAS的渗透,证明了FCVA可作为一种制备Al₂O₃涂层的新方法以提高TBC的抗CMAS腐蚀性能,且Al₂O₃涂层及其制备过程对TBC的热震性能均无消极影响。     

功率对激光熔覆(Fe0.25Co0.25Ni0.25Cr0.125Mo0.125)86B14涂层组织均质性及磨损性能的影响*

目前激光熔覆缺少对涂层组织、相结构纵向均质性与性能关联的研究。采用激光熔覆技术,选取不同的激光功率,制备(Fe_0.25Co_0.25Ni_0.25Cr_0.125Mo_0.125)₈₆B₁₄ 高熵合金涂层;借助电子探针(EPMA)、扫描电子显微镜(SEM)、能谱仪(EDS)和 X 射线衍射仪(XRD)等观察涂层微观组织与物相纵向分布,利用显微硬度计和摩擦磨损试验机测试涂层不同深度部位显微硬度及磨损性能,分析激光功率对熔覆(Fe_0.25Co_0.25Ni_0.25Cr_0.125Mo_0.125)₈₆B₁₄ 涂层纵向组织、物相分布影响规律及磨损性能。结果表明：三种功率下,涂层均由 BCC+FCC 相、硬质相 Mo₂B 组成,Mo₂B 在枝晶间富集。随着功率的增加,涂层中底部显微组织由细枝晶向粗大的柱状晶转变。三种涂层硬度均由表及里先增加后降低,摩擦因数先降低后增加;但是当激光功率为 1.6 kW 时,涂层呈现以 BCC 相为主的 FCC+BCC 双相结构,且由表及里 BCC 相含量不断增加、Mo₂B 含量逐渐减少,涂层组织均质化最高,摩擦因数变化梯度最小,耐磨损性能最佳。激光功率会影响熔覆高熵合金耐磨涂层均质性,进而影响摩擦性能的稳定性。     

CoCrNiAlY涂层制备工艺对组织形态及高温氧化行为的影响

为了研究CoCrNiAlY涂层微观组织结构对高温氧化行为和剥落行为的影响规律,采用激光熔覆技术和等离子喷涂工艺在718高温合金表面制备CoCrNiAlY涂层,观察其微观组织形态。利用XRD和SEM对1150 ℃高温氧化试验样品进行氧化层物相分析和形貌观察。结果表明,激光熔覆制备的CoCrNiAlY涂层中形成了胞状亚结构的等轴晶凝固组织,相对于等离子喷涂制备的CoCrNiAlY涂层结构更致密,具有更优异的抗高温氧化性能。在高温氧化过程中,等离子喷涂CoCrNiAlY涂层生成了以Cr₂O₃结构为主的复合氧化膜。激光熔覆CoCrNiAlY涂层生成Al₂O₃结构的单一氧化膜,而且熔覆层中原位形成的Y₂O₃钉扎作用能有效提高氧化膜的抗剥落性。文中系统分析讨论了两种不同工艺制备的组织形态对高温氧化膜形成机制的影响,激光熔覆涂层在高温下主要是以界面扩散方式形成致密的Al₂O₃膜,等离子喷涂涂层在高温下以界面反应的方式快速形成Cr₂O₃复合氧化膜。     

304不锈钢表面Ni-Al2O3复合镀层制备及性能研究

采用复合电沉积法在304奥氏体不锈钢表面制备Ni-Al₂O₃纳米镀层. 研究了Al₂O₃颗粒在复合镀层中的分布情况, 确定了镀液中颗粒的最佳加入量、最佳电流强度和最佳搅拌速度. 用扫描电镜和能谱仪、X射线衍射仪等设备鉴定镀层显微组织与组成. 结果表明, Ni-Al₂O₃纳米复合镀层均匀、致密、晶粒细小; 复合镀层结合强度、耐腐蚀性能优良, 抗高温氧化性能优于纯镍镀层.     

激光重熔Al2O3-TiO2涂层的强韧性能

采用等离子喷涂和激光重熔复合工艺在Ti-6Al-4V基体上制备了Al₂O₃-TiO₂涂层,通过X射线衍射(XRD)、扫描电镜(SEM)、显微硬度试验和压痕试验等方法研究了激光重熔对涂层的组织及强韧性能的影响.结果表明,等离子喷涂Al₂O₃-TiO₂涂层中的主相为γ-Al₂O₃,而相应重熔涂层中的主相为α-Al₂O₃.激光重熔可消除喷涂态涂层内部的孔隙、微裂纹和层状堆垛等微观缺陷,获得致密化的组织,并使涂层与基体形成良好冶金结合.重熔涂层的硬度比相应喷涂态涂层约提高了50%,裂纹扩展抗力相比喷涂态涂层提高了近两倍.激光重熔纳米涂层中的未熔增强颗粒和纳米结构特性等对涂层起到了协同强化和韧化作用.     

BN/Al2O3 复合粉末及其聚合物基复合材料的制备与导热性能

采用固-液相共混法制备了多种BN/Al₂O₃复合粉末,通过冻融法和表面修饰法对BN进行了改性处理,改变表面修饰剂类型和摩尔比得到了前驱体和烧结态BN/Al₂O₃复合粉末,并利用机械混合法制备了聚合物基BN/Al₂O₃复合材料,并测试分析了其导热性能。结果表明,经冻融处理的BN分散性和界面相容性明显优于未经冻融处理的BN。多巴胺对BN的改性效果优于聚乙二醇。采用多巴胺作为表面修饰剂且BN与Al(NO₃)₃的摩尔比为1:1时,能够得到纳米Al₂O₃均匀包覆的微米BN粉末,即BN/Al₂O₃微纳复合粉末,其聚合物基复合材料的导热系数可达0.62 W·m^-1·K^-1,是纯聚合物导热系数的3倍,是采用纯微米BN粉末制备的聚合物基复合材料导热系数的1.5倍。在BN表面附着的Al₂O₃可以形成层状热传导通道,能够有效提高聚合物基BN/Al₂O₃复合材料的热导率。     

ZrO2纳米颗粒对Al-12.5%Si合金PEO陶瓷层性能的影响

采用外加ZrO₂纳米颗粒的电解液体系在Al-12.5%Si合金表面制备ZrO₂- Al₂O₃- SiO₂三相PEO陶瓷层。利用SEM和XRD对陶瓷层微观结构和物相进行分析,并对其隔热及热冲击性能进行测试。结果表明：ZrO₂纳米颗粒显著提高了膜层的致密度和结合性,并有效减弱了Si元素对PEO成膜的抑制作用,提高了成膜速率;三相PEO陶瓷层的主要物相为SiO₂及高温稳定相α-Al₂O₃和c-ZrO₂,其独特的微结构和成分致使ZrO₂纳米颗粒改性的陶瓷层具有良好的热防护性能和热冲击性能。     

不同Cr含量的Ni-Cr合金熔覆层的高温氧化和热腐蚀特性

采用激光熔覆技术制备了Cr质量分数为10%、20%和40%的Ni-Cr合金熔覆层,研究了其在900 ℃下的高温氧化特性和600 ℃下Na₂SO₄+25% K₂SO₄混合盐中热腐蚀特性。结果表明,Cr含量对熔覆层的高温特性起着关键作用。提高Cr含量对提升熔覆层抗硫酸盐诱导的热腐蚀能力比提升抗循环高温氧化能力更有效。Cr40涂层抗高温氧化和热腐蚀性能最佳。Cr10的氧化产物以NiO为主,极易脱落,内部氧化严重。虽然Cr40表面可以形成单一的Cr₂O₃层,但热应力和生长应力引起的富Cr氧化物内部开裂,使Cr40的抗循环高温氧化能力仅略好于Cr20。面对热腐蚀时,Cr10表面呈现层状NiO和Ni₃S₂叠层分布的腐蚀产物,内部腐蚀区也生成了Ni的硫化物。Cr20表面Cr₂O₃层被破坏,内部腐蚀严重,生成了CrS。Cr40表面生成了致密的Cr₂O₃保护层,有效地防止了进一步腐蚀。     

Effects of K2O-Li2O doping on surface and catalytic properties of Fe2O3/Cr2O3 system

The effects of K₂O and Li₂O-doping (0.5, 0.75 and 1.5 mol%) of Fe₂O₃/Cr₂O₃ system on its surface and the catalytic properties were investigated. Pure and differently doped solids were calcined in air at 400-600 °C. The formula of the un-doped calcined solid was 0.85Fe₂O₃:0.15Cr₂O₃. The techniques employed were TGA, DTA, XRD, N₂ adsorption at −196 °C and catalytic oxidation of CO oxidation by O₂ at 200-300 °C. The results revealed that DTA curves of pure mixed solids consisted of one endothermic peak and two exothermic peaks. Pure and doped mixed solids calcined at 400 °C are amorphous in nature and turned to α-Fe₂O₃ upon heating at 500 and 600 °C. K₂O and Li₂O doping conducted at 500 or 600 °C modified the degree of crystallinity and crystallite size of all phases present which consisted of a mixture of nanocrystalline α- and γ-Fe₂O₃ together with K₂FeO₄ and LiFe₅O₈ phases. However, the heavily Li₂O-doped sample consisted only of LiFe₅O₈ phase. The specific surface area of the system investigated decreased to an extent proportional to the amount of K₂O and Li₂O added. On the other hand, the catalytic activity was found to increase by increasing the amount of K₂O and Li₂O added. The maximum increase in the catalytic activity, expressed as the reaction rate constant (k) measured at 200 °C, attained 30.8% and 26.5% for K₂O and Li₂O doping, respectively. The doping process did not modify the activation energy of the catalyzed reaction but rather increased the concentration of the active sites without changing their energetic nature.     

Sinterability and dielectric properties of Ba0.55Sr0.4Ca0.05TiO3-CaTiSiO5-Mg2TiO4 composite ceramics

The composite ceramics of Ba_0.55Sr_0.4Ca_0.05TiO₃-CaTiSiO₅-Mg₂TiO₄ (BSCT-CTS-MT) were prepared by the conventional solid-state route. The sintering performance, phase structures, morphologies, and dielectric properties of the composite ceramics were investigated. The BSCT-CTS-MT ceramics were sintered at 1100 °C and possessed dense microstructure. The dielectric constant was tailored from 1196 to 141 as the amount of Mg₂TiO₄ increased from 0 to 50 wt%. The dielectric constant and dielectric loss of 40 wt% Ba_0.55Sr_0.4Ca_0.05TiO₃-10 wt% CaTiSiO₅-50 wt% Mg₂TiO₄ was 141 and 0.0020, respectively, and the tunability was 8.64% under a DC electric field of 8.0 kV/cm. The Curie peaks were broadened and depressed after the addition of CaTiSiO₅. The optimistic dielectric properties made it a promising candidate for the application of tunable capacitors and phase shifters.     

Preparation and characteristic of spherical Li3V2(PO4)3

Spherical Li₃V₂(PO₄)₃ was synthesized by using N₂H₄ as reducer. The products were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that single-phase, spherical and well-dispersed Li₃V₂(PO₄)₃ has been successfully synthesized in our experimental process. Electrochemical behaviors have been characterized by charge/discharge measurements. The initial discharge capacities of Li₃V₂(PO₄)₃ were 123 mAh g⁻¹ in the voltage range of 3.0–4.3 V and 132 mAh g⁻¹ in the voltage range of 3.0–4.8 V.     

Sol-gel synthesis of Bi3.25La0.75Ti3O12 nanotubes

Ferroelectric Bi_3.25La_0.75Ti₃O₁₂ (BLT) nanotubes were synthesized by sol-gel technique using nanochannel porous anodic aluminum oxide (AAO) templates, and were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM). BLT nanotubes with diameter of around 240 nm and the wall thickness of about 25 nm exhibited a single orthorhombic perovskite structure and highly preferential crystal growth along the [1 1 7] orientation, which have smooth wall morphologies and well-defined diameters corresponding to the diameter of the applied template. The formation mechanism of BLT nanotubes was discussed.     

Low temperature sintering and microwave dielectric properties of (Mg0.7Zn0.3)0.95Co0.05TiO3 ceramics with BaCu(B2O5) additions

The effects of BaCu(B₂O₅) additives on the sintering temperature and microwave dielectric properties of (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics were investigated. The (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics were not able to be sintered below 1000 °C. However, when BaCu(B₂O₅) were added, they were sintered below 1000 °C and had the good microwave dielectric properties. It was suggested that a liquid phase with the composition of BaCu(B₂O₅) was formed during the sintering and assisted the densification of the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics at low temperature. BaCu(B₂O₅) powders were produced and used to reduce the sintering temperature of the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics. Good microwave dielectric properties of Q × f = 35,000 GHz, ?_r = 18.5.0 and τ_f = −51 ppm/°C were obtained for the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics containing 7 wt.% mol% BaCu(B₂O₅) sintered at 950 °C for 4 h.     

FRICTION WELDING OF Zr55Al10Ni5Cu30 BULK METALLIC GLASS

采用摩擦焊对Zr₅₅Al₁₀Ni₅Cu₃₀块体金属玻璃进行了焊接, 当焊机主轴转速为4.0×10³---5.0×10³ r/min, 摩擦压力为80---100 MPa, 摩擦时间为0.2---0.4 s, 顶锻压力和保压时间分别为200 MPa和2 s时, 能够成功实施Zr₅₅Al₁₀Ni₅Cu₃₀金属玻璃的焊接. 用SEM, XRD和TEM观察分析未检测到晶化相, 焊缝处金属仍保持非晶状态. 金属玻璃的塑性在玻璃转变点T_g附近随温度变化很大, 在T_g以上具有良好的塑性变形能力, 这是实施摩擦焊焊接的重要基础.     

废旧锂离子电池中Li, Fe和V的回收及xLiFePO4-yLi3V2(PO4)3的制备

由于LiFePO_4和Li_3V_2(PO_4)_3材料的特征相近,制备方法类似,提供了一种从废旧LiFePO_4和Li_3V_2(PO_4)_3混合电池中回收Li、Fe和V,再制备xLiFePO_4-yLi_3V_2(PO_4)_3的方法。在空气气氛中600℃热处理1h后,去除粘结剂PVDF使活性物质与集流体分离。调节Li、Fe、V和P摩尔比,球磨、锻烧,配制不同比例的xLiFePO_4-yLi_3V_2(PO_4)_3(x:y=5:1,7:1,9:1)复合电极材料。表征了其形貌、结构和电化学性能,结果表明,回收制备的复合材料将同时具备LiFePO_4和Li_3V_2(PO_4)_3两种材料的电化学性能,能显著改善LiFePO_4的倍率性能。     

固相-水热法制备LiFePO4-Li3V2（PO4）3复合材料及其电化学性能（英文）

分别采用固相-水热法和球磨法制备磷酸亚铁锂-磷酸钒锂复合正极材料(LiFePO4-Li3V2(PO4)3)。电化学性能测试表明,LiFePO4-Li3V2(PO4)3复合正极材料的电化学性能远远高于 LiFePO4和 Li3V2(PO4)3单独作为正极材料的性能,并且以固相-水热法制备的复合材料性能优于以球磨法制得的复合材料。研究发现 LiFePO4-Li3V2(PO4)3复合材料有 4 个氧化还原峰,相当于 LiFePO4 和 Li3V2(PO4)3 氧化还原峰的叠加。采用固相-水热法制备的LiFePO4-Li3V2(PO4)3 复合材料形貌较为规则,且有新相物质产生,这是导致其电化学性能较好的原因。     

二维ZnO/ Bi3.9Zn0.4V1.7O10.5纳米异质结构的制备及其可见光催化活性

表面建造是提高半导体光催化活性的一种有效方法。本文利用Zn5(CO3)2(OH)6纳米片为基底沉积了BiVO4再通过煅烧成功制备了二维ZnO/Bi3.9Zn0.4V1.7O10.5复合纳米片。通过X射线衍射,透射电镜和元素映像技术表征了所制样品。结果显示随着锌与铋的原子比的上升,ZnO多孔片状的表面逐渐变成Bi3.9Zn0.4V1.7O10.5物质。但其比例高于1:0.02时,在片状Bi3.9Zn0.4V1.7O10.5的区域表面又生长出BiVO4纳米颗粒。漫反射光谱测试显示出ZnO/Bi3.9Zn0.4V1.7O10.5复合物随着锌与铋的原子比的上升其在400~600 nm可见光区的吸收逐渐增强。所制样品在可见光（波长大于420 nm）进行了光催化降解罗丹明B的测试,结果表明在所制样品中,锌与铋的原子比为1:0.0133的ZnO/Bi3.9Zn0.4V1.7O10.5纳米片虽然其可见光的吸收并没有明显增强但却表现出最佳的光催化活性。荧光与电化学测试得出了低含量BZVO的ZnO纳米片可见光催化活性的提高主要是因为表面ZnO/Bi3.9Zn0.4V1.7O10.5异质结构提高了光生载流子的分离与传送。这种二维材料的表面建造有利于光催化的进行。因此,此法可应用于其它二维纳米材料的建造以提高光催化活性。     

Synthesis and characterization of Y3Al5O12 and ZrO2-Y2O3 thermal barrier coatings by combustion spray pyrolysis

Y₃Al₅O₁₂ and ZrO₂-Y₂O₃ (8 mol% YSZ) coatings for potential application as thermal barrier coatings were prepared by combustion spray pyrolysis. Thermal cycling of as deposited coatings on stainless steel and FeCrAlY bond coat substrates was carried out at 1000 °C and 1200 °C to determine the thermal fatigue response. Structural and morphological studies on Y₃Al₅O₁₂ and 8 mol% YSZ coatings before and after thermal cycling have been carried out. It has been noted that the coatings on FeCrAlY substrates remain intact after 50 cycles between room temperature and 1200 °C, whereas the coatings on stainless steel show some minor damage such as peeling off near the periphery after 50 cycles at 1000 °C. Thermal diffusivity values of Y₃Al₅O₁₂ and 8 mol% YSZ films were measured by using photo thermal deflection spectroscopy and the values are lower than those of coatings produced by conventional techniques such as EBPVD and APS.