Micro‐Supercapacitors Based on Interdigital Electrodes of Reduced Graphene Oxide and Carbon Nanotube Composites with Ultrahigh Power Handling Performance

A novel method for fabricating micro‐patterned interdigitated electrodes based on reduced graphene oxide (rGO) and carbon nanotube (CNT) composites for ultra‐high power handling micro‐supercapacitor application is reported. The binder‐free microelectrodes were developed by combining electrostatic spray deposition (ESD) and photolithography lift‐off methods. Without typically used thermal or chemical reduction, GO sheets are readily reduced to rGO during the ESD deposition. Electrochemical measurements show that the in‐plane interdigital design of the microelectrodes is effective in increasing accessibility of electrolyte ions in‐between stacked rGO sheets through an electro‐activation process. Addition of CNTs results in reduced restacking of rGO sheets and improved energy and power density. Cyclic voltammetry (CV) measurements show that the specific capacitance of the micro‐supercapacitor based on rGO–CNT composites is 6.1 mF cm^?2 at 0.01 V s^?1. At a very high scan rate of 50 V s^?1, a specific capacitance of 2.8 mF cm^?2 (stack capacitance of 3.1 F cm^?3) is recorded, which is an unprecedented performance for supercapacitors. The addition of CNT, electrolyte‐accessible and binder‐free microelectrodes, as well as an interdigitated in‐plane design result in a high‐frequency response of the micro‐supercapacitors with resistive‐capacitive time constants as low as 4.8 ms. These characteristics suggest that interdigitated rGO–CNT composite electrodes are promising for on‐chip energy storage application with high power demands.     

Flexible Carbon Dots-Intercalated MXene Film Electrode with Outstanding Volumetric Performance for Supercapacitors

2D MXenes have emerged as promising supercapacitor electrode materials due to their metallic conductivity, pseudo-capacitive mechanism, and high density. However, layer-restacking is a bottleneck that restrains their ionic kinetics and active site exposure. Herein, a carbon dots-intercalated strategy is proposed to fabricate flexible MXene film electrodes with both large ion-accessible active surfaces and high density through gelation of calcium alginate (CA) within the MXene nanosheets followed by carbonization. The formation of CA hydrogel within the MXene nanosheets accompanied by evaporative drying endow the MXene/CA film with high density. In the carbonization process, the CA-derived carbon dots can intercalate into the MXene nanosheets, increasing the interlayer spacing and promoting the electrolytic diffusion inside the MXene film. Consequently, the carbon dots-intercalated MXene films exhibit high volumetric capacitance (1244.6 F cm⁻³ at 1 A g⁻¹), superior rate capability (662.5 F cm⁻³ at 1000 A g⁻¹), and excellent cycling stability (93.5% capacitance retention after 30 000 cycles) in 3 m H₂SO₄. Additionally, an all-solid-state symmetric supercapacitor based on the carbon dots-intercalated MXene film achieves a high volumetric energy density of 27.2 Wh L⁻¹. This study provides a simple yet efficient strategy to construct high-volumetric performance MXene film electrodes for advanced supercapacitors.     

Layered Silicon‐Based Nanosheets as Electrode for 4 V High‐Performance Supercapacitor

Silicon‐based materials have shown great potential and been widely studied in various fields. Unlike its unparalleled theoretical capacity as anodes for batteries, few investigations have been reported on silicon‐based materials for applications in supercapacitors. Here, an electrode composed of layered silicon‐based nanosheets, obtained through oxidation and exfoliation, for a supercapacitor operated up to 4 V is reported. These silicon‐based nanosheets show an areal specific capacitance of 4.43 mF cm^?2 at 10 mV s^?1 while still retaining a specific capacitance of 834 µF cm^?2 even at an ultrahigh scan rate of 50 000 mV s^?1. The volumetric energy and power density of the supercapacitor are 7.65 mWh cm^?3 and 9312 mW cm^?3, respectively, and the electrode can operate for 12000 cycles in a potential window of 4 V at 2 A g^?1, while retaining 90.6% capacitance. These results indicate that the silicon‐based nanosheets can be a competitive candidate as the supercapacitor electrode material.     

Structure‐Based Enhanced Capacitance: In Situ Growth of Highly Ordered Polyaniline Nanorods on Reduced Graphene Oxide Patterns

A novel method is described for fabricating an all‐solid‐state flexible micro‐supercapacitor. The microelectrodes of the supercapacitor are prepared by in situ electrodeposition of polyaniline (PANI) nanorods on the surface of reduced graphene oxide (rGO) patterns that are fabricated by micromolding in capillaries. The morphologies of PANI nanorods could be controlled by the concentration of aniline and the growth time in the electrodeposition process. The micro‐supercapacitor possesses electrochemical capacitance as high as 970 F g^?1 at a discharge current density of 2.5 A g^?1, as well as good stability, retaining 90% of its initial capacitance after 1700 consecutive cycles for the synergistic effect of these new rGO/PANI nanostructures. The results show that the method could represent a route for translating the interesting fundamental properties of rGO and conducting polymers into technologically viable energy devices. Furthermore, this study might further guide the preparation of functional graphene‐based materials.     

High‐Performance Ultrathin Flexible Solid‐State Supercapacitors Based on Solution Processable Mo1.33C MXene and PEDOT:PSS

MXenes, a young family of 2D transition metal carbides/nitrides, show great potential in electrochemical energy storage applications. Herein, a high performance ultrathin flexible solid‐state supercapacitor is demonstrated based on a Mo_1.33C MXene with vacancy ordering in an aligned layer structure MXene/poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonic acid) (PEDOT:PSS) composite film posttreated with concentrated H₂SO₄. The flexible solid‐state supercapacitor delivers a maximum capacitance of 568 F cm^?3, an ultrahigh energy density of 33.2 mWh cm^?3 and a power density of 19 470 mW cm^?3. The Mo_1.33C MXene/PEDOT:PSS composite film shows a reduction in resistance upon H₂SO₄ treatment, a higher capacitance (1310 F cm^?3) and improved rate capabilities than both pristine Mo_1.33C MXene and the nontreated Mo_1.33C/PEDOT:PSS composite films. The enhanced capacitance and stability are attributed to the synergistic effect of increased interlayer spacing between Mo_1.33C MXene layers due to insertion of conductive PEDOT, and surface redox processes of the PEDOT and the MXene.     

Engineering 3D Ion Transport Channels for Flexible MXene Films with Superior Capacitive Performance

2D MXene materials are of considerable interest for future energy storage. A MXene film could be used as an effective flexible supercapacitor electrode due to its flexibility and, more importantly, its high specific capacitance. However, although it has excellent electronic conductivity, sluggish ionic kinetics within the MXene film becomes a fundamental limitation to the electrochemical performance. To compensate for the relative deficiency, MXene films are frequently reduced to several micrometer dimensions with low mass loading (<1 mg cm^?2), to the point of detriment of areal performance and commercial value. Herein, for the first time, the design of a 3D porous MXene/bacterial cellulose (BC) self‐supporting film is reported for ultrahigh capacitance performance (416 F g^?1, 2084 mF cm^?2) with outstanding mechanical properties and high flexibility, even when the MXene loading reaches 5 mg cm^?2. The highly interconnected MXene/BC network enables both excellent electron and ion transport channel. Additionally, a maximum energy density of 252 µWh cm^?2 is achieved in an asymmetric supercapacitor, higher than that of all ever‐reported MXene‐based supercapacitors. This work exploits a simple route for assembling 2D MXene materials into 3D porous films as state‐of‐the‐art electrodes for high performance energy storage devices.     

Inkjet Printing of Self‐Assembled 2D Titanium Carbide and Protein Electrodes for Stimuli‐Responsive Electromagnetic Shielding

2D titanium carbides (MXene) possess significant characteristics including high conductivity and electromagnetic interference shielding efficiency (EMI SE) that are important for applications in printed and flexible electronics. However, MXene‐based ink formulations are yet to be demonstrated for proper inkjet printing of MXene patterns. Here, tandem repeat synthetic proteins based on squid ring teeth (SRT) are employed as templates of molecular self‐assembly to engineer MXene inks that can be printed as stimuli‐responsive electrodes on various substrates including cellulose paper, glass, and flexible polyethylene terephthalate (PET). MXene electrodes printed on PET substrates are able to display electrical conductivity values as high as 1080 ± 175 S cm^?1, which significantly exceeds electrical conductivity values of state‐of‐the‐art inkjet‐printed electrodes composed of other 2D materials including graphene (250 S cm^?1) and reduced graphene oxide (340 S cm^?1). Furthermore, this high electrical conductivity is sustained under excessive bending deformation. These flexible electrodes also exhibit effective EMI SE values reaching 50 dB at films with thicknesses of 1.35 µm, which mainly originate from their high electrical conductivity and layered structure.     

3D Macroscopic Architectures from Self‐Assembled MXene Hydrogels

Assembly of 2D MXene sheets into a 3D macroscopic architecture is highly desirable to overcome the severe restacking problem of 2D MXene sheets and develop MXene‐based functional materials. However, unlike graphene, 3D MXene macroassembly directly from the individual 2D sheets is hard to achieve for the intrinsic property of MXene. Here a new gelation method is reported to prepare a 3D structured hydrogel from 2D MXene sheets that is assisted by graphene oxide and a suitable reductant. As a supercapacitor electrode, the hydrogel delivers a superb capacitance up to 370 F g^?1 at 5 A g^?1, and more promisingly, demonstrates an exceptionally high rate performance with the capacitance of 165 F g^?1 even at 1000 A g^?1. Moreover, using controllable drying processes, MXene hydrogels are transformed into different monoliths with structures ranging from a loosely organized porous aerogel to a dense solid. As a result, a 3D porous MXene aerogel shows excellent adsorption capacity to simultaneously remove various classes of organic liquids and heavy metal ions while the dense solid has excellent mechanical performance with a high Young's modulus and hardness.     

Multilayer‐Folded Graphene Ribbon Film with Ultrahigh Areal Capacitance and High Rate Performance for Compressible Supercapacitors

Limited by 2D geometric morphology and low bulk packing density, developing graphene‐based flexible/compressible supercapacitors with high specific capacitances (gravimetric/volumetric/areal), especially at high rates, is an outstanding challenge. Here, a strategy for the synthesis of free‐standing graphene ribbon films (GRFs) for high‐performance flexible and compressible supercapacitors through blade‐coating of interconnected graphene oxide ribbons and a subsequent thermal treatment process is reported. With an ultrahigh mass loading of 21 mg cm^?2, large ion‐accessible surface area, efficient electron and ion transport pathways as well as high packing density, the compressed multilayer‐folded GRF films (F‐GRF) exhibit ultrahigh areal capacitance of 6.7 F cm^?2 at 5 mA cm^?2, high gravimetric/volumetric capacitances (318 F g^?1, 293 F cm^?3), and high rate performance (3.9 F cm^?2 at 105 mA cm^?2), as well as excellent cycling stability (109% of capacitance retention after 40 000 cycles). Furthermore, the assembled F‐GRF symmetric supercapacitor with compressible and flexible characteristics, can deliver an ultrahigh areal energy density of 0.52 mWh cm^?2 in aqueous electrolyte, almost two times higher than the values obtained from symmetric supercapacitors with comparable dimensions.     

A Facile,High‐Yield,and Freeze‐and‐Thaw‐Assisted Approach to Fabricate MXene with Plentiful Wrinkles and Its Application in On‐Chip Micro‐Supercapacitors

MXene, as a new member of the two‐dimensional (2D) material family, has been widely studied. However, people often pay close attention to the versatility of MXene while ignoring its low exfoliation yield. In this work, a simplified and effective strategy to exfoliate multilayer‐MXene via the gentle water freezing‐and‐thawing (FAT) approach is proposed. The volume expansion of intercalated water can promote the exfoliation of MXene nanosheets. The yield of large FAT‐MXene flakes with special wrinkles can reach 39% after four cycles of the FAT process. Moreover, combining with sonication treatment can boost the yield of small MXene to a record high value of 81.4%. With the help of a commercial interdigital mask, an on‐chip all‐MXene micro‐supercapacitor (MSC) assembled by large FAT‐MXene is fabricated, exhibiting high areal and volumetric capacitance of 23.6 mF cm^?2 and 591 F cm^?3, respectively. This remarkable electrochemical performance of MXene‐MSC also confirms the high quality of MXene through this FAT strategy. This study may open up a new method to simultaneously boost the yield of MXene with small or large flake sizes, facilitating large‐scale and size‐dependent research on MXene.     

Flexible Solid‐State Supercapacitor Based on Graphene‐based Hybrid Films

A flexible solid‐state asymmetric supercapacitor based on bendable film electrodes with 3D expressway‐like architecture of graphenes and “hard nano‐spacer” is fabricated via an extended filtration assisted method. In the designed structure of the positive electrode, graphene sheets are densely packed, and Ni(OH)₂ nanoplates are intercalated in between the densely stacked graphenes. The 3D expressway‐like electrodes exhibit superior supercapacitive performance including high gravimetric capacitance (≈573 F g^‐1), high volumetric capacitance (≈655 F cm^‐3), excellent rate capability, and superior cycling stability. In addition, another hybrid film of graphene and carbon nanotubes (CNT) is fabricated as the negative electrodes for the designed asymmetric device. In the obtained graphene@CNT films, CNTs served as the hard spacer to prevent restacking of graphene sheets but also as a conductive and robust network to facilitate the electrons collection/transport in order to fulfill the demand of high‐rate performance of the asymmetric supercapacitor. Based on these two hybrid electrode films, a solid‐state flexible asymmetric supercapacitor device is assembled, which is able to deliver competitive volumetric capacitance of 58.5 F cm^‐3 and good rate capacity. There is no obvious degradation of the supercapacitor performance when the device is in bending configuration, suggesting the excellent flexibility of the device.     

Flexible Asymmetric Supercapacitor Based on Structure‐Optimized Mn3O4/Reduced Graphene Oxide Nanohybrid Paper with High Energy and Power Density

A highly flexible Mn₃O₄/reduced graphene oxide (rGO) nanohybrid paper with high electrical conductivity and high mass loading of Mn₃O₄ nanofibers (0.71 g cm^?3) is developed via a facile gel formation and electrochemical reduction process, which is low‐cost, environmental friendly, and easy to scale up. Confined Mn₃O₄ nanofibers are well dispersed within the rGO sheets, which demonstrate to be a promising cathode material for flexible asymmetric supercapacitors (ASCs). When coupled with an electrochemically reduced rGO paper as the anode, a flexible ASC device, based on the Mn₃O₄/rGO nanohybrid paper as the cathode, is assembled; and it demonstrates remarkable electrochemical performance: a high volumetric capacitance of 54.6 F cm^?3 (546.05 mF cm^?2), and remarkable volumetric energy and power density (0.0055 Wh cm^?3 and 10.95 W cm^?3) being achieved with excellent cycling ability. The nanohybrid paper shows great improvement for flexible energy devices in terms of electrochemical properties.     

Growth of Vertically Aligned Tunable Polyaniline on Graphene/ZrO2 Nanocomposites for Supercapacitor Energy‐Storage Application

In‐situ hydrothermal method is employed to synthesize graphene/zirconium oxide composite from respective precursors graphene oxide and zirconium oxy‐nitrate. In this method, the graphene oxide is reduced itself to graphene and simultaneously metal oxide gets anchor on the graphene sheets. A novel method is also developed for the preparation of vertically aligned tunable polyaniline on the graphene/zirconium oxide nanocomposite, which leads to achieve high surface area (207.1 m² g^?1), high electrical conductivity (70.8 S cm^?1), high specific capacitance (1359.99 Fg^?1 at 1 mV s^?1), and high electrochemical performances as supercapacitor electrode materials. This vertically aligned conducting polymer gets easy contact with electrolyte ions and provides numerous redox active sites during charging and discharging. Moreover, such a simple and low cost assembly approach can be a pioneer for the large‐scale production of various functional architectures for energy storage and conversions.     

Phthalocyanine‐Based 2D Conjugated Metal‐Organic Framework Nanosheets for High‐Performance Micro‐Supercapacitors

2D conjugated metal‐organic frameworks (2D c‐MOFs) are emerging as a novel class of conductive redox‐active materials for electrochemical energy storage. However, developing 2D c‐MOFs as flexible thin‐film electrodes have been largely limited, due to the lack of capability of solution‐processing and integration into nanodevices arising from the rigid powder samples by solvothermal synthesis. Here, the synthesis of phthalocyanine‐based 2D c‐MOF (Ni₂[CuPc(NH)₈]) nanosheets through ball milling mechanical exfoliation method are reported. The nanosheets feature with average lateral size of ≈160 nm and mean thickness of ≈7 nm (≈10 layers), and exhibit high crystallinity and chemical stability as well as a p‐type semiconducting behavior with mobility of ≈1.5 cm² V^?1 s^?1 at room temperature. Benefiting from the ultrathin feature, the nanosheets allow high utilization of active sites and facile solution‐processability. Thus, micro‐supercapacitor (MSC) devices are fabricated mixing Ni₂[CuPc(NH)₈] nanosheets with exfoliated graphene, which display outstanding cycling stability and a high areal capacitance up to 18.9 mF cm^?2; the performance surpasses most of the reported conducting polymers‐based and 2D materials‐based MSCs.     

Functional Carbon Nanomesh Clusters

A new type of atom‐thin carbon nanomesh clusters (CMCs) is prepared through a self‐sacrificial and morphology‐reserved thermal transformation of electrodeposited zinc coordination polymer (Zn‐CP). Such a unique structure can effectively inhibit the sheet stacking due to the self‐formed cluster morphology of Zn‐CP. The clusters are composed of nitrogen‐doped, continuous, interconnected, one‐/two‐atom‐thick carbon nanosheets, which not only effectively inhibit the sheet stacking but also significantly benefit ion transport. As a result, as active electrode material of supercapacitor in aqueous electrolytes, the resultant nitrogen‐doped CMC (N‐CMC) yields a capacitance of up to 984 F g^?1 at 0.5 A g^?1 and excellent cycling stability with 137% of its initial capacitance after 40 000 cycles, both higher than most of reported graphene‐based and carbon‐based electrode materials. On the other hand, the final N‐doped CMC also exhibits superior electrocatalytic activities for oxygen reduction reaction.     

Self‐Assembly of Flexible Free‐Standing 3D Porous MoS2‐Reduced Graphene Oxide Structure for High‐Performance Lithium‐Ion Batteries

Flexible freestanding electrodes are highly desired to realize wearable/flexible batteries as required for the design and production of flexible electronic devices. Here, the excellent electrochemical performance and inherent flexibility of atomically thin 2D MoS₂ along with the self‐assembly properties of liquid crystalline graphene oxide (LCGO) dispersion are exploited to fabricate a porous anode for high‐performance lithium ion batteries. Flexible, free‐standing MoS₂–reduced graphene oxide (MG) film with a 3D porous structure is fabricated via a facile spontaneous self‐assembly process and subsequent freeze‐drying. This is the first report of a one‐pot self‐assembly, gelation, and subsequent reduction of MoS₂/LCGO composite to form a flexible, high performance electrode for charge storage. The gelation process occurs directly in the mixed dispersion of MoS₂ and LCGO nanosheets at a low temperature (70 °C) and normal atmosphere (1 atm). The MG film with 75 wt% of MoS₂ exhibits a high reversible capacity of 800 mAh g^?1 at a current density of 100 mA g^?1. It also demonstrates excellent rate capability, and excellent cycling stability with no capacity drop over 500 charge/discharge cycles at a current density of 400 mA g^?1.     

Substrate‐Free and Shapeless Planar Micro‐Supercapacitors

Micro‐supercapacitors (MSCs), albeit powerful, are unable to broaden their potential applications primarily because they are not as flexible and morphable as electronics. To address this problem, a universal strategy to fabricate substrate‐free, ultrathin, shapeless planar‐MSCs with high‐performance tenability under serious deformation is put forward. These represent a new class of “all‐inside‐one” film supercapacitors, achieved by encapsulating two‐dimensional interdigital microelectrodes within chemically cross‐linked polyvinyl‐alcohol‐based hydrogel electrolyte containing graphene oxide (GO). GO nanosheets significantly improve ionic conductivity, enhance the capacitance, and boost robustness of hydrogel electrolyte. Consequently, the entire MSC, while being only 37 µm thick, can be crumpled and its shape can self‐adjust through fluid channel ten times smaller than its original size without any damage, demonstrating shapelessness. Using MXene as active material, high single‐cell areal capacitance of 40.8 mF cm^?2 is achieved from microelectrodes as thin as 5 µm. Furthermore, to demonstrate wide applicability of this protocol, screen‐printed graphene‐based highly integrated MSCs connecting nine cells in series are fabricated to stably output a high voltage of 7.2 V while crumpling them from 0.11 to 0.01 cm^?3, manifesting superior performance uniformity. This protocol allows the coexistence of high performance with incredible flexibility that may greatly diversify MSCs' applications.     

Flexible All‐Solid‐State Supercapacitors of High Areal Capacitance Enabled by Porous Graphite Foams with Diverging Microtubes

The practical applications of wearable electronics rely on the successful development of flexible and integrable energy devices with small footprints. This work reports a completely new type of graphite foam made of strategically created superstructures with covalently attached diverging microtubes, and their applications as electrode supports for binder‐free and additive‐free flexible supercapacitors. Because of the enhanced volumetric surface areas compared to conventional graphite foams, a high loading of pseudocapacitive materials (Mn₃O₄, 3.91 mg cm^?2, 78 wt%) is achieved. The supercapacitors provide areal capacitances as high as 820 mF cm^?2 at 1 mV s^?1, while still maintaining high rate capability and 88% retention of capacitance after 3000 continuous charging and discharging cycles. When assembled as all‐solid‐state flexible symmetric supercapacitors, they offer one of the highest full‐cell capacitances (191 mF cm^?2) among similar manganese oxide/graphene foams, and retain 80% capacitance after 1000 mechanical cycles. The potential of such flexible supercapacitors is also manifested by directly powering electric nanomotors that can trace along letters “U” and T,” which is the first demonstration of flexible supercapacitors for wireless/portable nanomanipulation systems. This work could inspire a new paradigm in designing and creating 3D porous micro/nanosuperstructures for an array of self‐powered electronic and nanomechanical applications.     

Scalable Production of Graphene Inks via Wet‐Jet Milling Exfoliation for Screen‐Printed Micro‐Supercapacitors

The miniaturization of energy storage units is pivotal for the development of next‐generation portable electronic devices. Micro‐supercapacitors (MSCs) hold great potential to work as on‐chip micro‐power sources and energy storage units complementing batteries and energy harvester systems. Scalable production of supercapacitor materials with cost‐effective and high‐throughput processing methods is crucial for the widespread application of MSCs. Here, wet‐jet milling exfoliation of graphite is reported to scale up the production of graphene as a supercapacitor material. The formulation of aqueous/alcohol‐based graphene inks allows metal‐free, flexible MSCs to be screen‐printed. These MSCs exhibit areal capacitance (C_areal) values up to 1.324 mF cm^?2 (5.296 mF cm^?2 for a single electrode), corresponding to an outstanding volumetric capacitance (C_vol) of 0.490 F cm^?3 (1.961 F cm^?3 for a single electrode). The screen‐printed MSCs can operate up to a power density above 20 mW cm^?2 at an energy density of 0.064 µWh cm^?2. The devices exhibit excellent cycling stability over charge–discharge cycling (10 000 cycles), bending cycling (100 cycles at a bending radius of 1 cm) and folding (up to angles of 180°). Moreover, ethylene vinyl acetate‐encapsulated MSCs retain their electrochemical properties after a home‐laundry cycle, providing waterproof and washable properties for prospective application in wearable electronics.     

Liquid‐Gated Transistors Based on Reduced Graphene Oxide for Flexible and Wearable Electronics

Graphene is regarded as the ultimate material for future flexible, high‐performance, and wearable electronics. Herein, a novel, robust, all‐green, highly reliable (yield ≥ 99%), and upscalable technology is reported for wearable applications comprising reduced graphene oxide (rGO) as the electroactive component in liquid‐gated transistors (LGTs). rGO is a formidable material for future flexible and wearable applications due to its easy processability, excellent surface reactivity, and large‐area coverage. A novel protocol is established toward the high‐yield fabrication of flexible rGO LGTs combining high robustness (>1.5 h of continuous operation) with state‐of‐the‐art performances, being similar to those of their rigid counterparts operated under liquid gating, including field‐effect mobility of ≈10^?1 cm² V^?1 s^?1 and transconductance of ≈25 µS. Permeable membranes have been proven crucial to operate flexible LGTs under mechanical stress with reduced amounts of solution (<20 µL). Our rGO LGTs are operated in artificial sweat exploiting two different layouts based on lateral‐flow paper fluidics. These approaches pave the road toward future real‐time tracking of perspiration via a simple and cost‐effective approach. The reported findings contribute to the robust and scalable production of novel graphene‐based flexible devices, whose features fulfill the requirements of wearable electronics.