The Effect of Post-Heat Treatment on Microstructure of 316L Cold-Sprayed Coatings and Their Corrosion Performance

The combined effects of process gases and post-heat treatment temperature on the microstructure of 316L cold-sprayed coatings on Al5052 substrates have been investigated in this study. The stainless steel coatings were subjected to heat treatment at four different temperatures (250, 500, 750, and 1000 °C) to study the effect of heat treatment. In addition, the corrosion performances of the coatings at different process temperatures have been compared using the potentiodynamic scanning technique. Microstructural characterization of the coatings was carried out using scanning and transmission electron microscopy and x-ray diffraction. The results of present study showed that cold-sprayed stainless steel coatings processed with helium exhibited higher corrosion resistance than those of coatings sprayed with nitrogen process gas. This could partially be attributed to the reduction in porosity level (4.9%) and improvement of particle-particle bonding. In addition, evaluation of the mechanical and microstructural properties of the coatings demonstrated that subsequent heat treatment has major influence on the deposited layers sprayed with He process gas.     

超音速火焰喷涂316L不锈钢涂层性能研究

采用超音速火焰喷涂技术(HVOF)在高强钢表面制备了316L不锈钢涂层,利用扫描电镜、显微硬度仪、电化学测试系统等设备对涂层金相组织、硬度、结合性能和抗腐蚀性能等进行了测试,并分析了WC-CoCr中间层对316L不锈钢粉末涂层结合强度及涂层界面的影响。结果表明:超音速火焰喷涂316L不锈钢粉末颗粒在喷涂中变形充分,形成较致密的涂层,并具有超过400 HV0.1的显微硬度;涂层具有较高自腐蚀电位,耐蚀性优于高强钢;涂层结合强度随着涂层厚度的减小、基体硬度的增加而提高;WC-CoCr底层可改善涂层界面结合,从而改善316L不锈钢涂层的结合性能。     

Corrosion resistance of electrodeposited RE-Ni-W-P-SiC-PTFE composite coating in phosphoric and ferric chloride

1 Introduction During process, store and use in various kinds of environment, corrosion, wear, fatigue and rupture may happen in all materials and products. These kinds of failure and damages widely occur in industries, causing enormous losses to nationa…     

Titania nanostructured coating for corrosion mitigation of stainless steel

Anatase nanostructured coating has been prepared on 316 L stainless steel by sol-gel dip coating. The topography of the coatings surface has been analyzed using atomic force microscopy. The anticorrosion performance of the coatings has been evaluated using polarization curves. Effects of calcination temperature, withdrawal speed and times of coating on corrosion protection have been studied. The results showed calcination temperature of 400°C and withdrawal speed of 10 cm/min are desirable conditions to achieve high corrosion protection of 316 L stainless steel in chloride containing environments. Coatings with 3 times exhibit better resistance against corrosion in 0.5 molar NaCl solutions. This protection against corrosion arises from photocatalytic properties of anatase nanoparticles.     

Resistance to Corrosion of Zirconia Coatings Deposited by Spray Pyrolysis in Nitrided Steel

Coatings of zirconium oxide were deposited onto three types of stainless steel, AISI 316L, 2205, and tool steel AISI D2, using the ultrasonic spray pyrolysis method. The effect of the flux ratio on the process and its influence on the structure and morphology of the coatings were investigated. The coatings obtained, 600 nm thick, were characterized using x-ray diffraction, scanning electron microscopy, confocal microscopy, and atomic force microscopy. The resistance to corrosion of the coatings deposited over steel (not nitrided) and stainless steel nitrided (for 2 h at 823 K) in an ammonia atmosphere was evaluated. The zirconia coating enhances the stainless steel’s resistance to corrosion, with the greatest increase in corrosion resistance being observed for tool steel. When the deposition is performed on previously nitrided stainless steel, the morphology of the surface improves and the coating is more homogeneous, which leads to an improved corrosion resistance.     

316L不锈钢表面NbC涂层的制备与性能评价

目的探究NbC涂层作为惰性涂层在模拟体液中的耐腐蚀性能及血液相容性能,并为NbC涂层作为生物惰性涂层改善316L不锈钢心血管支架的表面性能提供参考依据。方法采用物理气相沉积法制备NbC涂层,并通过优化工艺参数改善涂层性能。采用扫描电子显微镜(SEM)、原子力显微镜(AFM)、X射线衍射仪(XRD)、纳米压痕仪和原位纳米划痕仪,对涂层的微观结构及性能进行研究。采用循环伏安法对涂层的耐腐蚀性能进行表征。采用血小板粘附实验对涂层的血小板粘附行为进行了评价。结果制备的涂层具有结合性能强和致密度高等优点。随着基体温度的升高,NbC涂层的力学性能、耐腐蚀性能及血小板粘附特性均得到明显改善,硬度及弹性模量分别由(12.5±0.2)GPa和(213±0.8)GPa上升到(24.5±0.4)GPa和(275±1.1) GPa,自腐蚀速率优化明显,由8.76×10~(-6)A/cm~2降到1.98×10~(-8)A/cm~2。结论 NbC涂层在模拟体液中具备与316L不锈钢相当的稳定性,但其腐蚀速率远低于316L不锈钢,血小板粘附数量及变形较基体316L不锈钢得到显著改善,有望成为改善316L不锈钢表面性能的惰性涂层。     

Corrosion Behavior of Candidate Materials Used for Urea Hydrolysis Equipment in Coal-Fired Selective Catalytic Reduction Units

Corrosion tests were performed in the laboratory in order to assess the corrosion resistance of candidate materials used in urea hydrolysis equipment. The materials to be evaluated were exposed at 145 °C for 1000 h. Alloys 316L, 316L Mod., HR3C, Inconel 718, and TC4 were evaluated. Additionally, aluminide and chromate coatings applied to a 316L substrate were examined. After exposure, the mass changes in the test samples were measured by a discontinuous weighing method, and the morphologies, compositions, and phases of the corrosion products were analyzed using scanning electron microscopy, energy-dispersive spectroscopy, and x-ray diffraction. Results indicated that continuous pitting and dissolution corrosion were the main failure modes for 316L stainless steel. 316L Mod. and HR3C alloy showed better corrosion resistance than 316L due to their relatively high Cr contents, but HR3C exhibited a strong tendency toward intergranular corrosion. Inconel 718, TC4, and aluminide and chromate coating samples showed similar corrosion processes: only depositions formed by hydrothermal reactions were observed. Based on these results, a possible corrosion process in the urea hydrolysis environment was discussed for these candidate materials and questions to be clarified were proposed.     

Poly(3‐octylthiophene) thermally treated as coating for corrosion protection of SS304 in sulfuric acid media

Poly(3‐octylthiophene) (P3OT) was synthesized by direct oxidation of the 3‐octylthiophene monomer using ferric chloride (FeCl₃) as an oxidant. Using the drop‐casting technique, P3OT coatings were deposited onto 304 type stainless steel electrodes. For the purpose of determining the effect of thermal annealing on the corrosion protection of stainless steel with P3OT coatings, the coated electrodes were thermally annealed for 30 h at two different temperatures, 55 and 100 °C. The corrosion behavior of P3OT coated stainless steel was investigated in 0.5 M sulfuric acid (H₂SO₄) at room temperature using potentiodynamic polarization curves (PPC), linear polarization resistance (LPR), and electrochemical impedance spectroscopy (EIS). The results indicated that the thermally treated P3OT coatings improved the corrosion resistance of the stainless steel in 0.5 M H₂SO₄. The best corrosion protection was obtained by the P3OT coating annealed at 100 °C. In order to study the temperature effect on the morphology of the coatings before and after the corrosive environment and compare it with corrosion protection, atomic force microscopy (AFM) and scanning electronic microscopy (SEM) were used.     

Electrochemical evaluation of the corrosion protectiveness and porosity of vacuum annealed CrAlN and TiAlN cathodic arc physical vapor deposited coatings

The corrosion behavior of cathodic arc physical vapor deposited CrAlN and TiAlN coatings were examined in 1 M HCl solution before and after vacuum annealing at 700, 800, 900, and 1000 °C. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization (PDP) methods were used to study the corrosion behavior and porosity of the coatings in comparison with the bare steel substrate (304SS). Structural and mechanical characterization of the coatings were also conducted. It is found that with increasing annealing temperature, the mechanical properties of TiAlN increased due to age hardening caused by spinodal decomposition while the hardness of CrAlN decreased as result of relaxation. Similarly, EIS and PDP results revealed that the as‐deposited and annealed coatings offer higher corrosion resistance as compared to the bare 304SS substrate. The coatings susceptibility to corrosion is reduced after annealing as indicated by the increasing nobility of E_corr. Both PDP and EIS tests revealed that CrAlN coating annealed at 1000°C exhibited superior corrosion resistance properties. It is found that the reduced current density for CrAlN coating annealed at 1000°C was due to the reduction in the porosity. Annealed TiAlN coating follows similar behavior until an optimum annealing temperature of 800°C. Beyond this temperature, porosity enlargement and an increase in the number of pores subsequent to structural changes deteriorated the corrosion resistance of TiAlN coating.     

The corrosion and wear behavior of TiN and TiAlN coated AISI 316 L stainless steel

In this study, TiN and TiAlN coatings were deposited on AISI 316 L stainless steel substrates by PVD techniques. The composition and crystalline structure of the as-deposited coatings were analyzed by energy dispersive X-ray analysis (EDX) and X-ray diffraction (XRD) methods, respectively. The corrosion resistance studies of TiN-coated and TiAlN-coated samples were carried out in 0.9 wt % NaCl and SBF solutions using the electrochemical potentiodynamic polarization method and the wear behavior was evaluated with the ball-on-disk wear method at a sliding speed rate of 0.3 m/s under 2.5 N load in a dry medium. It was found that both TiN and TiAlN coatings exhibited relatively good corrosion resistance, however, TiAlN coatings showed a better corrosion resistance than TiN coatings. The TiAlN coating contributes positively against corrosion and wear behavior by increasing the surface hardness and by decreasing the friction coefficient of AISI 316 L stainless steel, respectively.     

大气等离子喷涂TiB2-316L不锈钢基复合涂层及其耐磨性能

分别采用高能球磨制备了TiB2含量(质量分数)为10%的316L不锈钢基复合粉,高能球磨与喷雾干燥造粒工艺制备了TiB2含量(质量分数)为40%的316L不锈钢基复合粉,大气等离子喷涂制备相应的TiB2-316L不锈钢基金属陶瓷涂层与316L不锈钢涂层.室温下采用高速环块磨损试验研究TiB2-316L不锈钢基金属陶瓷涂层的磨损特性.采用X射线衍射分析涂层物相,扫描电镜分析喷涂粉末、涂层结构和摩擦副磨损表面形貌.结果表明,大气等离子喷涂两种制粉工艺获得的316L不锈钢基TiB2复合粉能获得较耐磨的316L不锈钢基TiB2复合涂层,耐磨性高于316L不锈钢涂层,且TiB2在复合涂层中增强涂层耐磨性的原因是TiB2颗粒在涂层316L韧性基体中充当强化相,且TiB2在摩擦接触处摩擦氧化形成的氧化产物具有自润滑特性,能减少涂层的磨损量.     

Susceptibility of 316L stainless steel to crevice corrosion in submersible solenoid valve

The susceptibility of 316L stainless steel to crevice corrosion was investigated by using immersion test and electrochemical test. Three kinds of crevices including 316L‐to‐polytetrafluoroethylene (PTFE) crevice, 316L‐to‐fluoroelastomeric (FKM) crevice and 316L‐to‐316L crevice were tested in artificial seawater at 50°C. The results indicate that 316L stainless steel specimen is the most susceptible to crevice corrosion when it is coupled to 316L stainless steel crevice former, while it is the least susceptible when it is coupled to FKM crevice former. It suggests that during submersible solenoid valve design, the crevice of metal‐to‐metal should be moderately large so that crevice corrosion can not initiate and propagate, and FKM O‐ring rather than PTFE O‐ring should be selected as obturating ring. The corroded surface morphology was investigated using scanning electron microscopy (SEM) and atomic force microscopy (AFM). Three regions including passive region, active region and variable region can be observed on crevice corrosion sites.     

Corrosion behaviour of single and double layer hydroxyapatite coatings on 316L stainless steel by plasma spray

AISI316L stainless steel is extensively used in orthopedic and dental applications. However, this alloy exhibits low integration behaviour when it comes in contact with surrounding bone tissue and implant healing duration can be as much as few months. The aim of this study is the fabrication of biocompatible hydroxyapatite (HA) coatings on stainless steel substrate in order to accelerate the process of osseointegration of implants. The biocompatible single layer of Titania (TiO₂), Hydroxyapatite and bi-layer TiO₂/HA coatings were deposited by atmospheric plasma spray on 316L stainless steel. Coated and uncoated stainless steel specimens were incubated in simulated body fluids and 0.9% NaCl solutions for 1h and 7 days. In vitro electrochemical-corrosion evaluation of coated and uncoated stainless steel specimens have been investigated by Tafel extrapolation and linear polarization methods. Results indicates that corrosion resistance of single layer HA coated stainless steel specimens are superior to single layer TiO₂ and bi-layer HA/TiO₂ coated stainless steel specimens.     

Corrosion characteristics of polyaniline-coated 316L stainless steel in sulphuric acid containing fluoride

The corrosion resistance of conducting polyaniline (PANi) coatings deposited on 316L stainless steel (316L SS) at various cycle numbers of cyclic voltammetry (2-, 3- and 4-cycles) by electro-polymerization in sulphuric acid solution containing fluoride was investigated by electrochemical techniques. The corrosion resistance of the 316L SS substrate was considerably improved by the PANi coating. The increase of the cycle number of cyclic voltammetry increased the thickness and enhanced the performance of the PANi coating due to low porosity.     

Formation of Structure in Articles from Steel 316L Obtained by Cold Gas-Dynamic Spraying

Metal Science and Heat Treatment - Specimens from steel 316L obtained by four variants of cold gas-dynamic spraying of powders and subsequent hot isostatic pressing at a temperature of 1100°C...     

Plasma Sprayed Coating Using Mullite and Mixed Alumina/Silica Powders

Plasma sprayed ceramic coatings are widely used for thermal barrier coating applications. Commercially available mullite powder particles and a mixture of mechanically alloyed alumina and silica powder particles were used to deposit mullite ceramic coatings by plasma spraying. The coatings were deposited at three different substrate temperatures (room temperature, 300?°C, and 600?°C) on stainless steel substrates. Microstructure and morphology of both powder particles as well as coatings were investigated by using scanning electron microscopy. Phase formation and degree of crystallization of coatings were analyzed by x-ray diffraction. Differential thermal analysis (DTA) was used to study phase transformations in the coatings. Results indicated that the porosity level in the coatings deposited using mullite initial powder particles were lower than those deposited using the mixed initial powder particles. The degree of crystallization of the coatings deposited using the mixed powder particles was higher than that deposited using mullite powder particles at substrate temperatures of 25 and 300?°C. DTA curves of the coatings deposited using the mixed powders showed some transformation of the retained amorphous phase into mullite and alumina. The degree of crystallization of the as sprayed coatings using the mixed powder particles was significantly increased after post deposition heat treatments. The results indicated that the mechanically alloyed mixed powder can be used as initial powder particles for deposition of mullite coatings instead of using mullite powders.     

Corrosion of biomaterials: anodic treatment and evaluation of 316L stainless steel in simulated body fluid

The influence of electropolishing at different conditions on the electrochemical behaviour of 316L stainless steel (316L SS) in simulated body fluid (SBF) was investigated. Accordingly, 316L SS samples were electropolished in several electropolishing baths of H₃PO₄ and H₂SO₄ at 2–6 applied volts and 50–110°C for different time intervals. The corrosion behaviour then was studied by means of potentiodynamic polarisation technique and electrochemical impedance spectroscopy in SBF at 37°C. The surface morphology was also investigated by scanning electron microscopy. The results proved that the treated samples had better corrosion resistance than nonpolished one. The highest corrosion resistance was observed for the treated sample at 5?V and 90°C in 10:90 ratio of acidic electrolyte (H₃PO₄:H₂SO₄) for 15?min. Moreover, the corrosion resistances of anodically treated samples were found to be dependent greatly on applied volt, bath temperature, polishing time and phosphoric to sulphuric acids ratio.     

Electrochemical and in vitro behaviour of sol-gel coated 316L stainless steel

The corrosion resistance of AISI 316L stainless steel for biomedical applications, was significantly enhanced by means of inorganic and hybrid SiO₂ sol-gel coatings deposited by dip-coating. Coatings of 0.5-1.1 μm with different hybrid character were obtained by varying the temperature of thermal treatment from 400 to 550 °C. The pitting potential is increased up to 1 V and the current intensities were reduced up to 10⁻⁸ A/cm². After one month of immersion in simulated body fluids, all the coatings showed a high degree of corrosion resistance and integrity, being slightly better the behaviour of the hybrid coatings. Not any bioactivity signal was observed.     

In vitro electrochemical evaluation and phase purity of natural hydroxyapatite coating on medical grade 316L stainless steel

Natural hydroxyapatite (HA) has been electrophoretically deposited on the surface of medical grade 316L stainless steel (SS). Deposition was performed at various applied voltages of 30, 60, and 90 V for 3 min. After deposition the samples were dried at room temperature and sintered in a vacuum furnace (10⁻⁴–10⁻⁵ Torr) at 800 ^°C for 1 h. In vitro electrochemical studies were performed in the Hank's solution. The results showed that corrosion potential and breakdown potential of the coated samples shifted toward nobler potential compared with the uncoated 316L SS. Electrochemical impedance spectroscopy investigations revealed a higher polarization resistance, total impedance, and lower capacitance values for the coated samples compared to the bare one which indicated the improvement of corrosion resistance of the coated samples. The surface morphology of the samples was studied by a scanning electron microscope, and also phase purity and crystallinity of the coating material were investigated by X-ray diffraction. Deposition at 60 V for 3 min was found to be an optimum coating condition which led to the uniform, continuous, and crack-free coatings. The crystallinity of the coating materials was measured to be high, and quantitative analysis of the coatings after sintering showed some partial decomposition of natural HA to tricalcium phosphate.     

Corrosion Behaviour of 316L Stainless Steel in Hot Dilute Sulphuric Acid Solution with Sulphate and NaCl

Protection of Metals and Physical Chemistry of Surfaces - The corrosion behaviour of 316L stainless steel (316L SS) in 10% H2SO4 solution (94°C) with various concentrations of NaCl...