Micro-structural development of gap-graded blended cement pastes containing a high amount of supplementary cementitious materials

To clarify the strength improvement mechanism of gap-graded blended cements with a high amount of supplementary cementitious materials, phase composition of hardened gap-graded blended cement pastes was quantified, and compared with those of Portland cement paste and reference blended cement (prepared by co-grinding) paste. The results show that the gap-graded blended cement pastes containing only 25% cement clinker by mass have comparable amount of gel products and porosity with Portland cement paste at all tested ages. For gap-graded blended cement pastes, about 40% of the total gel products can be attributed to the hydration of fine blast furnace slag, and the main un-hydrated component is coarse fly ash, corresponding to un-hydrated cement clinker in Portland cement paste. Further, pore size refinement is much more pronounced in gap-graded blended cement pastes, attributing to high initial packing density of cement paste (grain size refinement) and significant hydration of BFS.     

Effect of utilizing unground and ground normal and black rice husk ash on the mechanical and durability properties of high-strength concrete

The aim of the present study is to investigate the effects of utilizing different processings of normal rice husk ash (RHA) and black rice husk ash (BRHA) on the mechanical and durability properties of high-strength concrete (HSC). Mechanical and durability properties of HSC were evaluated on concrete mixes containing unground BRHA and RHA and ground BRHA and RHA, their average particles sizes being 165, 85, 67 and 24 µm, respectively. The replacement of ordinary Portland cement with the ashes was adopted at 20%. The results showed that incorporating any form of RHA and BRHA in HSC reduced the slump value. The surface areas of RHA and BRHA, not their carbon content, determined the dosage of superplasticizer needed to achieve a targeted slump value. Concrete with unground and ground RHA incorporated exhibited 30% higher compressive strength while unground BRHA produced 30% lower compressive strength than that of the control concrete. Incorporating unground and ground RHA showed a synergy between filler and pozzolanic effect and had insignificant difference in mechanical and durability properties of the concretes. Meanwhile, incorporating ground BRHA showed a dominant filler effect in the concrete. Overall, the improvement of splitting tensile strength and modulus of elasticity of both RHA and GBRHA concrete showed a similar trend to that of the compressive strength of RHA concrete. The durability of concretes with unground and ground RHA and ground BRHA incorporated showed better performance than that of the control concrete. The material with 20% ground BRHA as partial cement replacement in HSC of Grade 50 could be used without any reduction in the mechanical and durability properties. Use of unground BRHA is not recommended because it did not improve these properties.     

Influence of 15 and 80 nano-SiO2 particles addition on mechanical and physical properties of ternary blended concrete incorporating rice husk ash

This study demonstrates the effects of SiO₂ nanoparticles as additives with two different sizes of 15 and 80?nm on compressive strength and porosity of rice husk ash (RHA) blended concrete. Up to 20% of ordinary Portland cement (OPC) was replaced by RHA with average particle size of 5 micron. Also, SiO₂ nanoparticles were added to the above mixture at four different weight percentages of 0.5, 1.0, 1.5 and 2.0 and cured in lime solution. The results indicated that compressive strength of Portland cement–nano SiO₂–rice husk ash (PC–NS–RHA) ternary blended concrete was considerably increased. Moreover, the total amount of porosity decreased to a minimum with respect to the control concrete. This improvement was observed at all the curing ages and replacement levels, but there was a gain in the optimal point with 20% of RHA plus 2% of 80?nm SiO₂ particles at 90 days of curing.     

Use of ultrafine rice husk ash with high-carbon content as pozzolan in high performance concrete

Rice husk ash (RHA) has been generated in large quantities in rice producing countries. This by-product can contain non-crystalline silica and thus has a high potential to be used as cement replacement in mortar and concrete. However, as the RHA produced by uncontrolled burning conditions usually contains high-carbon content in its composition, the pozzolanic activity of the ash and the rheology of mortar or concrete can be adversely affected. In this paper the influence of different grinding times in a vibratory mill, operating in dry open-circuit, on the particle size distribution, BET specific surface area and pozzolanic activity of the RHA is studied, in order to improve RHA’s performance. In addition, four high-performance concretes were produced with 0%, 10%, 15%, and 20% of the cement (by mass) replaced by ultrafine RHA. For these mixtures, rheological, mechanical and durability tests were performed. For all levels of cement replacement, especially for the 20%, the ultra-fine RHA concretes achieved superior performance in the mechanical and durability tests compared with the reference mixture. The workability of the concrete, however, was reduced with the increase of cement replacement by RHA.     

Strength development of concrete with rice-husk ash

This paper presents a study on the development of compressive strength up to 91 days of concretes with rice-husk ash (RHA), in which residual RHA from a rice paddy milling industry in Uruguay and RHA produced by controlled incineration from the USA were used for comparison. Two different replacement percentages of cement by RHA, 10% and 20%, and three different water/cementicious material ratios (0.50, 0.40 and 0.32), were used. The results are compared with those of the concrete without RHA, with splitting tensile strength and air permeability. It is concluded that residual RHA provides a positive effect on the compressive strength at early ages, but the long term behavior of the concretes with RHA produced by controlled incineration was more significant. Results of splitting tensile and air permeability reveal the significance of the filler and pozzolanic effect for the concretes with residual RHA and RHA produced by controlled incineration.     

Assessing the effect of biomass ashes with different finenesses on the compressive strength of blended cement paste

This study assesses the effect of biomass ashes with different finenesses on the compressive strength of blended cement paste. rice husk ash (RHA), palm oil fuel ash (POFA) and river sand (RS) were ground to obtain two finenesses: one was the same size as the cement, and the other was smaller than the cement. Type I Portland cement was replaced by RHA, POFA and RS at 0%, 10%, 20%, 30% and 40% by weight of binder. A water to binder ratio (W/B) of 0.35 was used for all blended cement paste mixes. The percentages of amorphous materials and the compressive strength of the pastes due to the hydration reaction, filler effect and pozzolanic reaction were investigated. The results showed that ground rice husk ash and ground palm oil fuel ash were composed of amorphous silica material. The compressive strength of the pastes due to the hydration reaction decreased with decreasing cement content. The compressive strength of the pastes due to the filler effect increased with increasing cement replacement. The compressive strengths of the pastes due to the pozzolanic reaction were nonlinear and were fit with nonlinear isotherms that increased with increasing fineness of RHA and POFA, cement replacement rate and age of the paste. In addition, the model that was proposed to predict the percentage compressive strength of the blended cement pastes on the basis of the age of the paste and the percentage replacement with biomass ash was in good agreement with the experimental results. The optimum replacement level of rice husk ash and palm oil fuel ash in pastes was 30% by weight of binder; this replacement percentage resulted in good compressive strengths.     

Influence of preparation method on the performance of ternary blended cements

This paper examined the feasibility of preparing high performance gap-graded blended cements by adding fine and coarse supplementary cementitious material (SCM) fractions into commercial Portland cement, and the efficiency of SCMs in gap-graded blended cements and interground blended cements were comparatively evaluated. The results show that the particle size distribution of gap-graded blended cements was much closer to a Fuller distribution, due to the intentional addition of fine and coarse SCMs, resulting in a higher initial packing density. As granulated blast furnace slag (GBFS) was mainly arranged in the fine fraction of the gap-graded blended cements, its efficiency was increased dramatically, contributing to 43.5% of the total measured hydration products. As a result, gap-graded blended cement pastes presented a homogeneous and dense microstructure due to “grain size refinement” and “pore size refinement”, therefore their setting times were decreased significantly, and both early and late strengths were increased remarkably in comparison to the interground blended cements investigated in this study.     

Nanoscale mechanical properties of concrete containing blast furnace slag and fly ash before and after thermal damage

Portland cement blended with waste products such as blast furnace slag and fly ash are frequently used to create more sustainable concrete, but their nanoscale mechanical behavior, particularly after thermal damage, has not been well-studied. Here, nanoindentation experiments confirm that concrete produced with blended cements contains hydration products with nearly identical nanoscale mechanical properties to the hydration products found in concretes produced with ordinary Portland cement. The volume fractions of the hydration products, particularly calcium-silicate-hydrate (C-S-H) phases, are formed in different proportions with the addition of fly ash and blast furnace slag. After exposure to fire damage, the nanoscale behavior of concretes produced with fly ash and slag also matches the nanoscale behavior of conventional concretes. This suggests that any macroscopic differences between fire damage behavior of blended cement concrete and ordinary Portland cement concrete must have origins in a larger length scale.     

Evaluation of compressive strength of hardening silica fume blended concrete

Silica fume (SF) is a byproduct of induction arc furnaces and has long been used as a mineral admixture to produce high-strength and high-performance concrete. Owing to the pozzolanic reaction between calcium hydroxide and SF, compared with Portland cement, the hydration of concrete containing SF is much more complex. In this paper, by considering the production of calcium hydroxide in cement hydration and its consumption in the pozzolanic reaction, a numerical model is proposed to simulate the hydration of concrete containing SF. The degree of hydration of cement and degree of reaction of SF are obtained as accompanied results from the proposed hydration model. Furthermore, on the basis of the volume stoichiometries, mixing proportions and the degree of reactions of cement and SF, the gel–space ratio of hydrating blended concrete is calculated. Finally, the development of compressive strength of SF blended concrete is evaluated through Powers’ strength theory considering the contributions of cement hydration and SF reaction. The proposed model is verified through experimental data on concrete with different water-to-cement ratios and SF substitution ratios.     

Effect of grinding of low-carbon rice husk ash on the microstructure and performance properties of blended cement concrete

The effectiveness of unground low-carbon rice husk ash (URHA) as a pozzolan and the effect of grinding the URHA to finer fractions for use in portland cement system were investigated. The properties investigated include the setting time and calcium hydroxide depletion of rice husk ash (RHA) pastes; microstructure and flow behavior of RHA mortars; strength and durability of RHA concretes. Results from this investigation suggested that the URHA and ground RHA (GRHA) mixtures performed better than the control mixtures in all tests conducted except water demand and setting time. The URHA mixture revealed denser microstructure compared to the control mixture. The internal porosity created by the coarse RHA grains in the matrix and their inability to completely participate in pozzolanic reaction may be the reasons for the poorer performance of the URHA mixture than compared to the GRHA mixture. The effect of grinding the RHA to finer fractions either substantially or slightly improved all properties except final setting time. With the performance of the GRHA concrete somewhat similar to that of the SF concrete, the use of ground RHA can be concluded to provide acceptable performance in portland cement systems.     

Durability assessment of alkali activated slag (AAS) concrete

The environmental impact from the production of cement has prompted research into the development of concretes using 100% replacement materials activated by alkali solutions. This paper reports research into the durability of AAS concrete. The durability properties of AAS have been studied for a range of sodium oxide dosages and activator modulus. Properties investigated have included measurements of workability, compressive strength, water sorptivity, depth of carbonation and rapid chloride permeability. Microstructure studies have been conducted using scanning electron microscopy and energy dispersive X-ray spectroscopy. It was concluded that an activator modulus of between 1.0 and 1.25 was identified as providing the optimum performance for a sodium oxide dosage of 5% and that AAS concretes can exhibit comparable strength to concrete currently produced using Portland cement (PC) and blended cements. However, with regards to the durability properties such as water sorptivity, chloride and carbonation resistance; the AAS concretes exhibited lower durability properties than PC and blended concretes. This, in part, can be attributed to surface microcracking in the AAS concretes.     

Strength,drying shrinkage,and water permeability of concrete incorporating ground palm oil fuel ash

In this study, palm oil fuel ash (POFA) was used as a pozzolanic material in concrete. The POFA was ground to obtain two different finenesses: coarse (CP) and fine (FP). A portion of ordinary type I Portland cement (OPC) was replaced by CP and FP at 10%, 20%, and 30% by weight of binder to cast concrete. Compressive strength, modulus of elasticity, drying shrinkage, and water permeability of concretes containing ground POFA were measured. The results showed that the compressive strength of the concrete increased with the fineness of the POFA. With 10% and 30% replacement of OPC by CP and FP, respectively, the compressive strength of the resulting concrete was as high as that of OPC concrete at 90 days. Moreover, the use of 10–30% of FP as a cement replacement in concrete reduced its drying shrinkage and water permeability. Finally, there was also a strong correlation between the compressive strength and the water permeability of ground POFA concrete.     

The effects of supplementary cementing materials in modifying the heat of hydration of concrete

This paper is intended to provide guidance on the form and extent to which supplementary cementing materials, in combination with Portland cement, modifies the rate of heat evolution during the early stages of hydration in concrete. In this investigation, concretes were prepared with fly ash, condensed silica fume and ground granulated blastfurnace slag, blended with Portland cement in proportions ranging from 5% to 80%. These concretes were subjected to heat of hydration tests under adiabatic conditions and the results were used to assess and quantify the effects of the supplementary cementing materials in altering the heat rate profiles of concrete. The paper also proposes a simplified mathematical form of the heat rate curve for blended cement binders in concrete to allow a design stage assessment of the likely early-age time–temperature profiles in large concrete structures. Such an assessment would be essential in the case of concrete structures where the potential for thermally induced cracking is of concern.     

A multi-phase kinetic model to simulate hydration of slag–cement blends

Ground granulated blast furnace slag, which shows cementitious behavior (latent hydraulic activity) and pozzolanic characteristics (reaction with lime), has been widely used as a mineral admixture in normal and high strength concretes. Hydration of slag–blended cement is much more complex than that of ordinary Portland cement because of the mutual interactions between the cement hydration and the slag reaction. This paper presents a kinetic hydration model for cement–slag blends. The proposed model analyzes the slag reaction separate from cement hydration by considering the production of calcium hydroxide in cement hydration and its consumption in slag reactions. The amount of free water and the amount of calcium hydroxide left in the system were adopted as the control indicators for determining the slag reaction. Using the proposed model, the reaction ratio of slag can be evaluated as a function of curing age, considering the influences of the water to binder ratio, the slag replacement ratio and the curing temperature. Furthermore, the amount of chemically-bound water (self-cementing properties), calcium hydroxide (pozzolanic capabilities), and the heat released from hydration are evaluated by determining the contributions from both the cement hydration and the slag reaction. The evaluated results show good accordance with the experimental results.     

Influence de la durée d'une cure humide sur les caractéristiques mécaniques de bétons d'usage courant

If, due to lack of water, the hydration of cement is slowed or stopped, the evolution of the mechanical properties of concrete ceases. The role of the curing process is to maintain sufficient humidity during hydration so that the desired properties are achieved. Eight mix proportions of concrete cast with ordinary Portland cement and blended Portland cement (four of each type) are studied in order to cover a large range of the commonly used concretes. The results show that the undesirable effects of inadequate wet curing on the mechanical properties of concrete are closely related to the cement content. The results thus suggest quantitative rules to compensate for the loss of performance due to inadequate curing by increasing the cement content.     

Water absorption control of ternary blended concrete with nano-SiO2 in presence of rice husk ash

In the current study, the effects of SiO₂ nanoparticles as additive with two different sizes of 15 and 80?nm on water absorption of rice husk ash (RHA) blended concrete have been investigated. Concrete samples were prepared by replacing 10, 15 and 20?wt% of cement with RHA and 0.5, 1.0, 1.5 and 2.0% of cement with SiO₂ nanoparticles followed by curing in lime solution for 7, 28 and 90?days. The results indicated that the resistance to water absorption of Portland cement?Cnano SiO₂?Crice husk ash (PC?CNS?CRHA) ternary blended concrete was considerably improved with respect to the control concrete. This improvement was observed at all curing ages and replacement levels but the optimal point was reached for 20% of RHA incorporating 2% of 80?nm SiO₂ particles at 90?days of curing. Fast formation of C?CS?CH gel in the presence of ultra high active nano-sized SiO₂ and micron level RHA particles together with their high filler effect may result in a continuous cement paste with the lowest weak zones. It has been concluded that the use of novel ternary blended concrete (PC?CNS?CRHA) provides significant reduction in the water absorption of concrete.     

The use of oil shale ash in Portland cement concrete

An experimental investigation was undertaken to study the potential use of Jordanian oil shale ash (OSA) as a raw material or an additive to Portland cement mortar and concrete. Different series of mortar and concrete mixtures were prepared at different water to binder ratios, and different OSA replacements of cement and/or sand. The compressive strength of mortar and concrete specimens, cured in water at 23 °C, was determined over different curing periods which ranged from 3 to 90 days. The results of these tests were subjected to a statistical analysis. Equations were developed by regression analysis techniques to relate the effect of batch constituents on the strength developments of OSA mortars and concretes. The models were checked for accuracy by comparing their predictions with actual test results.The obtained results indicated that OSA replacement of cement, sand or both by about 10% (by wt) would yield the optimum compressive strength, and that its replacement of cement by up to 30% would not reduce its compressive strength, significantly. It was found that OSA on its own possesses a limited cementitious value and that its contribution to mortar or concrete comes through its involvement in the pozzolanic reactions. The statistical model developed showed an excellent predictability of the compressive strength for mortar and concrete mixes.     

Effect of rice-husk ash on durability of cementitious materials

In this paper the effects of partial replacements of Portland cement by rice-husk ash (RHA) on the durability of conventional and high performance cementitious materials are investigated. Different percentages of RHA replacement levels, two RHAs (amorphous and partially crystalline optimized by dry-milling) and several water–cementitious materials ratio are studied. The following durability aspects were tested: air permeability, chloride ion penetration, alkali-silica expansion, sulfate and acid resistance. The results were compared with those of cementitious materials without RHA. It is concluded from the tested properties that the incorporation of both RHAs in concretes show different behaviors for air permeability and chloride ion penetration depending on the water/cementitious materials ratio used; in mortars, it reduces the mass loss of specimens exposed to hydrochloric acid solution and decreases the expansion due to sulfate attack and the alkali-silica reaction. The results of durability aspects due to physical or pozzolanic effects after the addition of both RHAs, and its chemical composition, in general indicate an enhanced performance, proving the feasibility of its rational utilization as a supplementary cementing material.     

Portland cement-fly ash-silica fume systems in concrete

Laboratory flow, strength, and ultrasnic pulse velocity tests were performed on mortars made with 70% (by weight) of portland cement and 30% of pozzolanic materials where the pozzolanic materials consisted of various combinations of fly ash and silica fume. In addition to these ternary systems, binary blends, such as Portland cement and fly ash, and Portland cement and silica fume, along with 100% Portland cement mortars, were investigated for comparison. The purpose of the investigation, preliminary in nature, was to see under what circumstances, if any, would be a synergistic action when a ternary system of Portland cement-fly ash-silica fume is used in a mortar or concrete.Mortars were made with two cements of type I and two cements of type III along with class F and class C fly ashes. One silica fume was used. Standard flow tests were performed on the fresh mortars, and compressive strength as well as ultrasonic pulse velocity tests were performed with each hardened mortar at various ages up to 28 days. It is expected that the results and conclusions obtained here on mortars will be transferable to concretes.There are several novel, or at least lesser known, results of the investigation. For instance, a new explanation is offered for the plasticizing effect of fly ash which is based on the optimum particle-size distribution concept. Another such result is that ground fly ash produced greater flow increases with type I cement than with type III. A third finding is that the superplasticizer is more effective in increasing the flow as well as strength when the mortars contain fly ash and/or silica fume than in the case of mortars without mineral admixture. Also, it appears that when type I cement is used, the silica fume in the quantity of 5% of the weight of the cement produces relatively greater strength increase in the presence of fly ash than without fly ash.These promising results are preliminary in nature. Therefore, further research is justified with ternary systems in concrete. The presented work is a portion of a larger investigation.     

A study on reinforcement corrosion and related properties of plain and blended cement concretes under different curing conditions

This paper presents the results of an experimental investigation on the steel reinforcement corrosion, electrical resistivity, and compressive strength of concretes. Concretes having two different water–cement ratios (0.65 and 0.45) and two different cement contents (300 and 400 kg/m³) were produced by using a plain and four different blended portland cements. Concrete specimens were subjected to three different curing procedures (uncontrolled, controlled, and wet curing). The effect of using plain or blended cements on the resistance of concrete against damage caused by corrosion of the embedded reinforcement has been investigated using an accelerated impressed voltage setup. The resistivity of the cover concrete has been measured non-destructively by placing electrodes on concrete surface. The compressive strength, electrical resistivity, and corrosion resistance of the concretes were determined at different ages up to 180 days. The results of the tests indicated that the wet curing was essential to achieve higher strength and durability characteristics for both plain and especially blended cement concretes. The concretes, which received inadequate (uncontrolled) curing, exhibited poor performance in terms of strength and corrosion resistance.