Evaluation of advanced p‐PERL and n‐PERT large area silicon solar cells with 20.5% energy conversion efficiencies

In this paper, we evaluate p‐type passivated emitter and rear locally diffused (p‐PERL) and n‐type passivated emitter and rear totally diffused (n‐PERT) large area silicon solar cells featuring nickel/copper/silver (Ni/Cu/Ag) plated front side contacts. By using front emitter p‐PERL and rear emitter n‐PERT, both cell structures can be produced with only a few adaptations in the entire process sequence because both feature the same front side design: homogeneous n⁺ diffused region with low surface concentration, SiO₂/SiN_x:H passivation, Ni/Cu/Ag plated contacts. Energy conversion efficiencies up to 20.5% (externally confirmed at FhG‐ISE Callab) are presented for both cell structures on large area cells together with power‐loss analysis and potential efficiency improvements based on PC1D simulations. We demonstrate that the use of a rear emitter n‐PERT cell design with Ni/Cu/Ag plated front side contacts enables to reach open‐circuit voltage values up to 676 mV on 1–2 Ω cm n‐type CZ Si. We show that rear emitter n‐PERT cells present the potential for energy conversion efficiencies above 21.5% together with a strong tolerance to wafer thickness and bulk resistivity. Copyright © 2014 John Wiley & Sons, Ltd.     

20.0% Efficiency Si Nano/Microstructures Based Solar Cells with Excellent Broadband Spectral Response

Spectral response of solar cells determines the output performance of the devices. In this work, a 20.0% efficient silicon (Si) nano/microstructures (N/M‐Strus) based solar cell with a standard solar wafer size of 156 × 156 mm² (pseudo‐square) has been successfully fabricated, by employing the simultaneous stack SiO₂/SiN_x passivation for the front N/M‐Strus based n⁺‐emitter and the rear surface. The key to success lies in the excellent broadband spectral responses combining the improved short‐wavelength response of the stack SiO₂/SiN_x passivated Si N/M‐Strus based n⁺‐emitter with the extraordinary long‐wavelength response of the stack SiO₂/SiN_x passivated rear reflector. Benefiting from the broadband spectral response, the highest open‐circuit voltage (V_oc) and short‐circuit current density (J_sc) reach up to 0.653 V and 39.0 mA cm^?2, respectively. This high‐performance screen‐printed Si N/M‐Strus based solar cell has shown a very promising way to the commercial mass production of the Si based high‐efficient solar cells.     

20.7% efficient ion‐implanted large area n‐type front junction silicon solar cells with rear point contacts formed by laser opening and physical vapor deposition

In this work, we report on ion‐implanted, high‐efficiency n‐type silicon solar cells fabricated on large area pseudosquare Czochralski wafers. The sputtering of aluminum (Al) via physical vapor deposition (PVD) in combination with a laser‐patterned dielectric stack was used on the rear side to produce front junction cells with an implanted boron emitter and a phosphorus back surface field. Front and back surface passivation was achieved by thin thermally grown oxide during the implant anneal. Both front and back oxides were capped with SiN_x, followed by screen‐printed metal grid formation on the front side. An ultraviolet laser was used to selectively ablate the SiO₂/SiN_x passivation stack on the back to form the pattern for metal–Si contact. The laser pulse energy had to be optimized to fully open the SiO₂/SiN_x passivation layers, without inducing appreciable damage or defects on the surface of the n⁺ back surface field layer. It was also found that a low temperature annealing for less than 3 min after PVD Al provided an excellent charge collecting contact on the back. In order to obtain high fill factor of ~80%, an in situ plasma etching in an inert ambient prior to PVD was found to be essential for etching the native oxide formed in the rear vias during the front contact firing. Finally, through optimization of the size and pitch of the rear point contacts, an efficiency of 20.7% was achieved for the large area n‐type passivated emitter, rear totally diffused cell. Copyright © 2014 John Wiley & Sons, Ltd.     

Stack system of PECVD amorphous silicon and PECVD silicon oxide for silicon solar cell rear side passivation

A stack of hydrogenated amorphous silicon (a‐Si) and PECVD‐silicon oxide (SiO_x) has been used as surface passivation layer for silicon wafer surfaces. Very good surface passivation could be reached leading to a surface recombination velocity (SRV) below 10 cm/s on 1 Ω cm p‐type Si wafers. By using the passivation layer system at a solar cell's rear side and applying the laser‐fired contacts (LFC) process, pointwise local rear contacts have been formed and an energy conversion efficiency of 21·7% has been obtained on p‐type FZ substrates (0·5 Ω cm). Simulations show that the effective rear SRV is in the range of 180 cm/s for the combination of metallised and passivated areas, 120 ± 30 cm/s were calculated for the passivated areas. Rear reflectivity is comparable to thermally grown silicon dioxide (SiO₂). a‐Si rear passivation appears more stable under different bias light intensities compared to thermally grown SiO₂. Copyright © 2008 John Wiley & Sons, Ltd.     

Front and rear silicon‐nitride‐passivated multicrystalline silicon solar cells with an efficiency of 18.1%

A solar cell process designed to utilise low‐temperature plasma‐enhanced chemical vapour deposited (PECVD) silicon nitride (SiN_x) films as front and rear surface passivation was applied to fabricate multicrystalline silicon (mc‐Si) solar cells. Despite the simple photolithography‐free processing sequence, an independently confirmed efficiency of 18.1% (cell area 2 × 2 cm²) was achieved. This excellent efficiency can be predominantly attributed to the superior quality of the rear surface passivation scheme consisting of an SiN_x film in combination with a local aluminium back‐surface field (LBSF). Thus, it is demonstrated that low‐temperature PECVD SiN_x films are well suited to achieve excellent rear surface passivation on mc‐Si. Copyright © 2002 John Wiley & Sons, Ltd.     

High efficiency screen printed bifacial solar cells on monocrystalline CZ silicon

We present industrialized bifacial solar cells on large area (149 cm²) 2 cm CZ monocrystalline silicon wafers processed with industrially relevant techniques such as liquid source BBr₃ and POCl₃ open‐tube furnace diffusions, plasma enhanced chemical vapor deposition (PECVD) SiN_x deposition, and screen printed contacts. The fundamental analysis of the paste using at boron‐diffused surface and the bifacial solar cell firing cycle has been investigated. The resulting solar cells have front and rear efficiencies of 16.6 and 12.8%, respectively. The ratio of the rear J_SC to front J_SC is 76.8%. It increases the bifacial power by 15.4% over a conventional solar cell at 20% of 1‐sun rear illumination, which equals to the power of a conventional solar cell with 19.2% efficiency. We also present a bifacial glass–glass photovoltaic (PV) module with 30 bifacial cells with the electrical characteristics. Copyright © 2010 John Wiley & Sons, Ltd.     

Experimental evidence of parasitic shunting in silicon nitride rear surface passivated solar cells

Many solar cells incorporating SiN_x films as a rear surface passivation scheme have not reached the same high level of cell performance as solar cells incorporating high‐temperature‐grown silicon dioxide films as a rear surface passivation. In this paper, it is shown by direct comparison of solar cells incorporating the two rear surface passivation schemes, that the performance loss is mainly due to a lower short‐circuit current while the open‐circuit voltage is equally high. With a solar cell test structure that features a separation of the rear metal contacts from the passivating SiN_x films, the loss in short‐circuit current can be reduced drastically. Besides a lower short‐ circuit current, dark I–V curves of SiN_x rear surface passivated solar cells exhibit distinct shoulders. The results are explained by parasitic shunting of the induced floating junction (FJ) underneath the SiN_x films with the rear metal contacts. The floating junction is caused by the high density of fixed positive charges in the SiN_x films. Other two‐dimensional effects arising from the injection level dependent SRV of the Si/SiN_x interfaces are discussed as well, but, are found to be of minor importance. Pinholes in the SiN_x films and optical effects due to a different internal rear surface reflectance can be excluded as a major cause for the performance loss of the SiN_x rear surface passivated cells. Copyright © 2002 John Wiley & Sons, Ltd.     

20.1%‐efficient crystalline silicon solar cell with amorphous silicon rear‐surface passivation

We have developed a crystalline silicon solar cell with amorphous silicon (a‐Si:H) rear‐surface passivation based on a simple process. The a‐Si:H layer is deposited at 225°C by plasma‐enhanced chemical vapor deposition. An aluminum grid is evaporated onto the a‐Si:H‐passivated rear. The base contacts are formed by COSIMA (contact formation to a‐Si:H passivated wafers by means of annealing) when subsequently depositing the front silicon nitride layer at 325°C. The a‐Si:H underneath the aluminum fingers dissolves completely within the aluminum and an ohmic contact to the base is formed. This contacting scheme results in a very low contact resistance of 3.5 ±0.2 mΩ cm² on low‐resistivity (0.5 Ω cm) p‐type silicon, which is below that obtained for conventional Al/Si contacts. We achieve an independently confirmed energy conversion efficiency of 20.1% under one‐sun standard testing conditions for a 4 cm² large cell. Measurements of the internal quantum efficiency show an improved rear surface passivation compared with reference cells with a silicon nitride rear passivation. Copyright © 2005 John Wiley & Sons, Ltd.     

Optimizing annealing steps for crystalline silicon solar cells with screen printed front side metallization and an oxide‐passivated rear surface with local contacts

Silicon solar cells that feature screen printed front contacts and a passivated rear surface with local contacts allow higher efficiencies compared to present industrial solar cells that exhibit a full area rear side metallization. If thermal oxidation is used for the rear surface passivation, the final annealing step in the processing sequence is crucial. On the one hand, this post‐metallization annealing (PMA) step is required for decreasing the surface recombination velocity (SRV) at the aluminum‐coated oxide‐passivated rear surface. On the other hand, PMA can negatively affect the screen printed front side metallization leading to a lower fill factor. This work separately analyzes the impact of PMA on both, the screen printed front metallization and the oxide‐passivated rear surface. Measuring dark and illuminated IV‐curves of standard industrial aluminum back surface field (Al‐BSF) silicon solar cells reveals the impact of PMA on the front metallization, while measuring the effective minority carrier lifetime of symmetric lifetime samples provides information about the rear side SRV. One‐dimensional simulations are used for predicting the cell performance according to the contributions from both, the front metallization and the rear oxide‐passivation for different PMA temperatures and durations. The simulation also includes recombination at the local rear contacts. An optimized PMA process is presented according to the simulations and is experimentally verified. The optimized process is applied to silicon solar cells with a screen printed front side metallization and an oxide‐passivated rear surface. Efficiencies up to 18.1% are achieved on 148.8 cm² Czochralski (Cz) silicon wafers. Copyright © 2009 John Wiley & Sons, Ltd.     

Economic feasibility of bifacial silicon solar cells

Bifacial solar cells and modules are a promising approach to increase the energy output of photovoltaic systems, and therefore decrease levelized cost of electricity (LCOE). This work discusses the bifacial silicon solar cell concepts PERT (passivated emitter, rear totally diffused) and BOSCO (both sides collecting and contacted) in terms of expected module cost and LCOE based on in‐depth numerical device simulation and advanced cost modelling. As references, Al‐BSF (aluminium back‐surface field) and PERC (passivated emitter and rear) cells with local rear‐side contacts are considered. In order to exploit their bifacial potential, PERT structures (representing cells with single‐sided emitter) are shown to require bulk diffusion lengths of more than three times the cell thickness. For the BOSCO concept (representing cells with double‐sided emitter), diffusion lengths of half the cell thickness are sufficient to leverage its bifacial potential. In terms of nominal LCOE, BOSCO cells are shown to be cost‐competitive under monofacial operation compared with an 18% efficient (≙ p_MPP = 18 mW/cm²) multicrystalline silicon (mc‐Si) Al‐BSF cell and a 19% mc‐Si PERC cell for maximum output power densities of p_MPP ≥ 17.3 mW/cm² and p_MPP ≥ 18.1 mW/cm², respectively. These values assume the use of $10/kg silicon feedstock for the BOSCO and $20/kg for the Al‐BSF and PERC cells. For the PERT cell, corresponding values are p_MPP ≥ 21.7 mW/cm² and p_MPP ≥ 22.7 mW/cm², respectively, assuming the current price offset (≈50%, at the time of October 2014) of n‐type Czochralski‐grown silicon (Cz‐Si) compared with mc‐Si wafers. The material price offset of n‐type to p‐type Cz‐Si wafers (≈15%, October 2014) currently accounts for approximately 1 mW/cm², which correlates to a conversion efficiency difference of 1%_abs for monofacial illumination with 1 sun. From p‐type mc‐Si to p‐type Cz‐Si (≈30% wafer price offset, October 2014), this offset is approximately 2.5 mW/cm² for a PERT cell. When utilizing bifacial operation, these required maximum output power densities can be transformed into required minimum rear‐side illumination intensities for arbitrary front‐side efficiencies η_front by means of the performed numerical simulations. For a BOSCO cell with η_front = 18%, minimum rear‐side illumination intensities of ≤ 0.02 suns are required to match a 19% PERC cell in terms of nominal LCOE. For an n‐type Cz‐Si PERT cell with η_front = 21%, corresponding values are ≤ 0.11 suns with 0.05 suns being the n‐type to p‐type material price offset. This work strongly motivates the use of bifacial concepts to generate lowest LCOE. Copyright © 2016 John Wiley & Sons, Ltd.     

Variations in the properties of an implantation-synthesized SixNy-Si heterosystem as a result of thermal and ion-beam treatments

Transmission electron microscopy, infrared spectroscopy, and the measurements of current-voltage characteristics and capacitance were used to study the influence of heat treatment and the long-range effect of irradiation of the rear side of an Si wafer with Ar, Ne, and Si ions on the state of an Si_xN_y layer synthesized at the front side of this wafer. It is ascertained that the argon-ion bombardment of the wafer heated to 500°C is the most effective method for the formation of insulating silicon-nitride layers. The fact that the properties of Si_xN_y layers are scarcely affected by irradiation with neon and silicon ions is consistent with the previously suggested model of a spontaneous-acoustic mechanism of the long-range effect produced by irradiation of silicon with argon ions.     

High efficiency screen‐printed EFG Si solar cells through rapid thermal processing‐induced bulk lifetime enhancement

This paper shows that one second (1 s) firing of Si solar cells with screen‐printed Al on the back and SiN _x anti‐reflection coating on the front can produce a high quality Al‐doped back‐surface‐field (Al‐BSF) and significantly enhance SiN _x ‐induced defect hydrogenation in the bulk Si. Open‐circuit voltage, internal quantum efficiency measurements, and cross‐sectional scanning electron microscopy pictures on float‐zone silicon cells revealed that 1 s firing in rapid thermal processing at 750°C produces just as good a BSF as 60 s firing, indicating that the quality of Al‐BSF region is not a strong function of RTP firing time at 750°C. Analysis of edge‐defined film‐fed grown (EFG) Si cells showed that short‐term firing is much more effective in improving the hydrogen passivation of bulk defects in EFG Si. Average minority‐carrier lifetime in EFG wafers improved from ∼3 to ∼33 μs by 60 s firing but reached as high as 95μs with 1 s firing, resulting in 15·6% efficient screen‐printed cells on EFG Si. Copyright © 2004 John Wiley & Sons, Ltd.     

Fine line printed silicon solar cells exceeding 20% efficiency

Silicon solar cells with passivated rear side and laser‐fired contacts were produced on float zone material. The front side contacts are built up in two steps, seed and plate. The seed layer is printed using an aerosol jet printer and a silver ink. After firing this seed layer through the silicon nitride layer, the conductive layer is grown by light induced plating. The contact formation is studied on different emitter sheet resistances, 55 Ω/sq, 70 Ω/sq, and on 110 Ω/sq. These emitters are passivated with a PECVD silicon nitride layer which also acts as an anti‐reflection coating. Even on the 110 Ω/sq emitters it was possible to reach a fill factor of 80·1%. The electrical properties i.e., the contact resistance of the front side contacts are studied by transfer length model (TLM) measurements. On a cell area of 4 cm² and emitter sheet resistance of 110 Ω/sq, a record efficiency of 20·3% was achieved. Excellent open‐circuit voltage (V_oc) and short‐circuit current (j_sc) values of 661 mV and 38·4 mA/cm² were obtained due to the low recombination in the 110 Ω/sq emitter and at the passivated rear surface. These results show impressively that it is possible to contact emitter profiles with a very high efficiency potential using optimized printing technologies. Copyright © 2008 John Wiley & Sons, Ltd.     

Large area tunnel oxide passivated rear contact n‐type Si solar cells with 21.2% efficiency

This paper reports on the implementation of carrier‐selective tunnel oxide passivated rear contact for high‐efficiency screen‐printed large area n‐type front junction crystalline Si solar cells. It is shown that the tunnel oxide grown in nitric acid at room temperature (25°C) and capped with n⁺ polysilicon layer provides excellent rear contact passivation with implied open‐circuit voltage iV_oc of 714 mV and saturation current density J_0b′ of 10.3 fA/cm² for the back surface field region. The durability of this passivation scheme is also investigated for a back‐end high temperature process. In combination with an ion‐implanted Al₂O₃‐passivated boron emitter and screen‐printed front metal grids, this passivated rear contact enabled 21.2% efficient front junction Si solar cells on 239 cm² commercial grade n‐type Czochralski wafers. Copyright © 2016 John Wiley & Sons, Ltd.     

Progress on large area n‐type silicon solar cells with front laser doping and a rear emitter

We report on the progress of imec's n‐type passivated emitter, rear totally diffused rear junction silicon solar cells. Selective laser doping has been introduced in the flow, allowing the implementation of a shallow diffused front surface field and a reduction of the recombination current in the contact area. Simplifications have been implemented towards a more industrial annealing sequence, by replacing expensive forming gas annealing steps with a belt furnace annealing. By applying these improvements, together with an advanced texturing process and emitter passivation by atomic layer deposition of Al₂O₃, 22.5% efficient cells (three busbars) have been realized on commercial 156 · 156 mm² Czochralski‐Si. This result has been independently confirmed by ISE CalLab. Copyright © 2016 John Wiley & Sons, Ltd.     

Thin Al2O3 passivated boron emitter of n‐type bifacial c‐Si solar cells with industrial process

We have presented thin Al₂O₃ (~4 nm) with SiN_x:H capped (~75 nm) films to effectively passivate the boron‐doped p⁺ emitter surfaces of the n‐type bifacial c‐Si solar cells with BBr₃ diffusion emitter and phosphorus ion‐implanted back surface field. The thin Al₂O₃ capped with SiN_x:H structure not only possesses the excellent field effect and chemical passivation, but also establishes a simple cell structure fully compatible with the existing production lines and processes for the low‐cost n‐type bifacial c‐Si solar cell industrialization. We have successfully achieved the large area (238.95 cm²) high efficiency of 20.89% (front) and 18.45% (rear) n‐type bifacial c‐Si solar cells by optimizing the peak sintering temperature and fine finger double printing technology. We have further shown that the conversion efficiency of the n‐type bifacial c‐Si solar cells can be improved to be over 21.3% by taking a reasonable high emitter sheet resistance. Copyright © 2017 John Wiley & Sons, Ltd.     

原子层沉积氧化铝薄膜对多晶太阳能电池表面钝化的影响

A stack of Al2O3/SiNx dual layer was applied for the back side surface passivation of p-type multi-crystalline silicon solar cells, with laser-opened line metal contacts, forming a local aluminum back surface field （local Al-BSF） structure. A slight amount of Al2O3, wrapping around to the front side of the wafer during the thermal atomic layer deposition process, was found to have a negative influence on cell performance. The different process flow was found to lead to a different cell performance, because of the Al2O3 wrapping around the front surface. The best cell performance, with an absolute efficiency gain of about 0.6% compared with the normal full Al-BSF structure solar cell, was achieved when the Al2O3 layer was deposited after the front surface of the wafer had been covered by a SiNx layer. We discuss the possible reasons for this phenomenon, and propose three explanations as the Ag paste, being hindered from firing through the front passivation layer, degraded the SiNx passivation effect and the Al2O3 induced an inversion effect on the front surface. Characterization methods like internal quantum efficiency and contact resistance scanning were used to assist our understanding of the underlying mechanisms.     

Front and Back‐Junction Carbon Nanotube‐Silicon Solar Cells with an Industrial Architecture

In the past, the application of carbon nanotube‐silicon solar cell technology to industry has been limited by the use of a metallic frame to define an active area in the middle of a silicon wafer. Here, industry standard device geometries are fabricated with a front and back‐junction design which allow for the entire wafer to be used as the active area. These are enabled by the use of an intermixed Nafion layer which simultaneously acts as a passivation, antireflective, and physical blocking layer as well as a nanotube dopant. This leads to the formation of a hybrid nanotube/Nafion passivated charge selective contact, and solar cells with active areas of 1–16 cm² are fabricated. Record maximum power conversion efficiencies of 15.2% and 18.9% are reported for front and back‐junction devices for 1 and 3 cm² active areas, respectively. By placing the nanotube film on the rear of the device in a back‐junction architecture, many of the design‐related challenges for carbon nanotube silicon solar cells are addressed and their future applications to industrialized processes are discussed.     

Opto‐electrical modelling and optimization study of a novel IBC c‐Si solar cell

Interdigitated back contact (IBC) crystalline silicon (c‐Si) solar cells are attracting a lot of attention because of their capability to reach world record conversion efficiency. Because of the relatively complex contact pattern, their design and optimization typically require advanced numerical simulation tools. In this work, a TCAD‐based simulation platform has been developed to account accurately and in detail the optical and passivation mechanisms of front texturization. Its validation has been carried out with respect to a novel homo‐junction IBC c‐Si solar cell based on ion implantation and epitaxial growth, comparing measured and simulated reflectance, transmittance, internal quantum efficiency, external quantum efficiency spectra, and current density–voltage characteristics. As a result of the calibration process, the opto‐electrical losses of the investigated device have been identified quantitatively and qualitatively. Then, an optimization study about the optimal front surface field (FSF) doping, front‐side texturing morphology, and rear side geometry has been performed. The proposed simulation platform can be potentially deployed to model other solar cell architectures than homo‐junction IBC devices (e.g., passivated emitter rear cell, passivated emitter rear locally diffused cell, hetero‐IBC cell). Simulation results show that a not‐smoothed pyramid‐textured front interface and an optimal FSF doping are mandatory to minimize both the optical and the recombination losses in the considered IBC cell and, consequently, to maximize the conversion efficiency. Similarly, it has been showed that recombination losses are affected more by the doping profile rather than the surface smoothing. Moreover, the performed investigation reveals that the optimal FSF doping is almost independent from the front texturing morphology and FSF passivation quality. According to this result, it has been demonstrated that an IBC cell featuring an optimal FSF doping does not exhibit a significant efficiency improvement when the FSF passivation quality strongly improves, proving that IBC cell designs based on low‐doped FSF require a very outstanding passivation quality to be competitive. Deploying an optimization algorithm, the adoption of an optimized rear side geometry can potentially lead to an efficiency improvement of about 1%_abs as compared with the reference IBC solar cell. Further, by improving both emitter and c‐Si bulk quality, a 22.84% efficient solar cell for 280‐μm thick c‐Si bulk was simulated. Copyright © 2017 John Wiley & Sons, Ltd.     

SiOyNx/SiNx stack: a promising surface passivation layer for high‐efficiency and potential‐induced degradation resistant mc‐silicon solar cells

A thin SiO_yN_x film was inserted below a conventional SiN_x antireflection coating used in c‐Si solar cells in order to improve the surface passivation and the solar cell's resistance to potential‐induced degradation (PID). The effect of varying the flow ratio of the N₂O and SiH₄ precursors and the deposition temperature for the SiO_yN_x thin film upon material properties were systematically investigated. An excellent surface passivation was obtained on FZ p‐type polished silicon wafers, with the best results obtained with a SiO_yN_x film deposited at a very low temperature of 130 °C and with an optical refractive index of 1.8. In the SiO_yN_x/SiN_x stack structure, a SiO_yN_x film with ~6 nm thickness is sufficient to provide excellent surface passivation with an effective surface recombination velocity S_eff < 2 cm/s. Furthermore, we applied the optimized SiO_yN_x/SiN_x stack on multicrystalline Si solar cells as a surface passivation and antireflection coating, resulting in a 0.5% absolute average conversion efficiency gain compared with that of reference cells with conventional SiN_x coating. Moreover, the cells with the SiO_yN_x/SiN_x stack layers show a significant increase in their resistance to PID. Nearly zero degradation in shunt resistance was obtained after 24 h in a PID test, while a single SiN_x‐coated silicon solar cell showed almost 50% degradation after 24 h. Copyright © 2016 John Wiley & Sons, Ltd.