Design of a printed log‐periodic dipole array antenna with high gain for millimeter‐wave applications

In this article, a V‐band printed log‐periodic dipole array (PLPDA) antenna with high gain is proposed. The antenna prototype is designed, simulated, fabricated, and tested. Simulation results show that this antenna can operate from 42 to 82 GHz with a fractional impedance bandwidth of 64.5% covering the whole V‐band (50–75 GHz). The antenna has a measured impedance matching bandwidth that starts from 42 to beyond 65 GHz with good agreement between the experimental and simulated results. At 50 and 65 GHz, the antenna has a measured gain of 10.45 and 10.28 dBi, respectively, with a gain variation of 2.6 dBi across the measured frequency range. The antenna prototype exhibits also stable radiation patterns over the operating band. It achieves side‐lobe suppression better than 17.26 dB in the H‐plane and better than 8.95 dB in the E‐plane, respectively. In addition, the cross‐polarization component is 18.5 dB lower than the copolarization with front‐to‐back ratio lower than 24.1 dB in both E‐ and H‐planes across the desired frequency range. Based on a comparison of performance among the reported work in the literature, we can say that the proposed PLPDA antenna is a proper candidate to be used in many applications at V‐band frequency. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:185–193, 2015.     

Millimeter‐wave planar high gain SIW antenna using half elliptic radiation slots

This article reports a high gain millimeter‐wave substrate integrated waveguide (SIW) antenna using low cost printed circuit board technology. The half elliptic slots which can provide small shunt admittance, low cross polarization level and low mutual coupling are etched on the board surface of SIW as radiation slots for large array application. Design procedure for analyzing the characteristics of proposed radiation slot, the beam‐forming structure and the array antenna are presented. As examples, an 8 × 8 and a 32 × 32 SIW slot array antennas are designed and verified by experiments. Good agreements between simulation and measured results are achieved, which shows the 8 × 8 SIW slot array antenna has a gain of 20.8 dBi at 42.5 GHz, the maximum sidelobe level of 42.5 GHz E‐plane and H‐plane radiation patterns are 22.3 dB and 22.1 dB, respectively. The 32 × 32 SIW slot array antenna has a maximum measured gain of 30.05 dBi at 42.5 GHz. At 42.3 GHz, the measured antenna has a gain of 29.6 dBi and a maximum sidelobe level of 19.89 dB and 15.0 dB for the E‐plane and H‐plane radiation patterns. © 2015 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:709–718, 2015.     

Low‐profile omnidirectional circularly polarized antenna based on substrate integrated waveguide technology

A substrate integrated waveguide (SIW) circularly polarized (CP) antenna with omnidirectional radiation in the azimuthal plane is proposed. The antenna consists of five identical end‐fire CP antenna elements in a pentagonal array configuration, which is loaded on a circular substrate. Each element contains an H‐plane horn antenna in SIW structure and a printed dipole antenna. Five parasitic curve elements are introduced to improve the omnidirectional property of the antenna. Combined with complementary dipoles theory and SIW technology, prototype antenna is designed, fabricated and measured. With a low profile of 0.024λ₀, the antenna has a 10‐dB return‐loss impedance bandwidth of 4.08% (2.4～2.5 GHz) and a 3‐dB axial‐ratio (AR) bandwidth of 5.76% (2.36～2.50 GHz). The antenna works well in the 2.45 GHz ISM band, with good cross‐polarization and excellent omnidirectional property.     

A triple‐band antenna for MIMO WLAN applications

A novel triple‐band antenna element by etching parasitic slot on ground plane is presented. A three‐element antenna system for WLAN MIMO communications is fabricated by using the proposed antenna element. The triple‐band antenna element is designed for the WLAN standard frequency ranges (2.4‐2.485, 5.15‐5.35, and 5.475‐5.725 GHz). The three identical antenna elements are rotationally symmetric on the substrate, isolated by using metal‐vias cavity. The measured average peak gain within the operational bandwidth is about 2.7 dBi. The isolation between the antenna elements can achieve better than 17 dB at the lower band (2.25‐2.65 GHz), while more than 32 dB at the higher bands (5.20‐5.35 and 5.47‐5.73 GHz) is obtained.     

Design and fabrication of a new high gain multilayer negative refractive index metamaterial antenna for X‐band applications

This article presents the design of a planar high gain and wideband antenna using a negative refractive index multilayer superstrate in the X‐band. This meta‐antenna is composed of a four‐layer superstrate placed on a conventional patch antenna. The structure resonates at a frequency of 9.4 GHz. Each layer of the metamaterial superstrate consists of a 7 × 7 array of electric‐field‐coupled resonators, with a negative refractive index of 8.66 to 11.83 GHz. The number of layers and the separation of superstrate layers are simulated and optimized. This metamaterial lens has significantly increased the gain of the patch antenna to 17.1 dBi. Measurements and simulation results proved about 10 dB improvement of the gain.     

Planar antenna beam deflection using low‐loss metamaterial for future 5G applications

A method to tilt the beam of a planar antenna in the E‐plane is demonstrated by implementing a metamaterial (MM) structure onto the antenna substrate at the fifth‐generation (5G) band of 3.5 GHz. The beam tilting is achieved due to the phase change that occurs when the electromagnetic (EM) wave traverses through two media with different refractive indices. A new adjacent square‐shaped resonator (ASSR) structure is proposed to achieve the beam tilting in a dipole antenna. This structure provides a very low loss of ?0.2 dB at 3.17 GHz. The simulation and measurement results illustrate that the radiation beam of the dipole antenna is tilted by +25° and ?24° depending on the position of the ASSR array onto the dipole antenna substrate. In addition, no degradation in the gain is observed as in the conventional beam‐tilting methods; in fact, gain enhancement values of 3 dB (positive deflection) and 2.7 dB (negative deflection) are obtained compared with that of a dipole antenna with no ASSR array. The reflection coefficient of the dipole antenna with ASSR array has a good agreement with that of the dipole antenna with no ASSR array. The measured results agree well with the simulated ones.     

A novel substrate integrated waveguide cavity‐backed self‐diplexing antenna array with frequency beam scanning characteristic

This article presented a substrate integrated waveguide (SIW) cavity‐backed self‐diplexing antenna array with frequency beam scanning characteristic. The proposed array consists of 16 SIW cavity‐backed slot antennas. The SIW cavity‐backed slot antenna can be fed by two separate ports to resonate at two different frequencies and achieve high isolation better than 20 dB between two input ports. The proposed element is a typical self‐diplexing antenna. These cavity‐backed slot antennas are shunt‐fed by a compact 1 to 16 SIW power divider and series‐fed by a set of microstrip lines, respectively. As a result, this array achieves an unidirectional radiation pattern at 10.2 GHz with high gain of 15.10 dBi, and a frequency beam scanning characteristic from 7.0 to 9.0 GHz ranging from ?50° to 46°.     

Wideband microstrip‐fed tapered slot antennas and phased array

Two wideband tapered slot antennas are designed, fabricated, and tested. The first antenna, which is fabricated on a high dielectric constant substrate (?_r = 10.2), shows a measured return loss of better than 10 dB from 1.6 to 12.4 GHz (7.7:1 bandwidth), and an antenna gain varying from 3.6 to 7.8 dBi. The second antenna is built on a low dielectric constant substrate (?_r = 2.2), and demonstrates return loss of better than 10 dB from 1.8 to 15.2 GHz (8.4:1 bandwidth). The second antenna also has improved antenna gain, from 5 to 15.6 dBi, and is used to build a wideband 1 × 4 H‐plane phased array with a total gain of 9–17 dBi and a beam steering angle of ±15° from 3 to 12 GHz. © 2007 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2007.     

A 60‐GHz on‐chip slot‐array antenna in integrated‐passive‐device technology for antenna‐in‐package applications

A new millimeter‐wave antenna structure on a low‐cost, production platform integrated passive device technology is presented. The antenna consists of a 2‐by‐1 array of slot antennas at 60 GHz. An in‐house developed on‐chip antenna measurement setup was used to characterize the fabricated antenna. The measurement results show an antenna gain of more than 5 dBi with a return loss of 18 dB at 60 GHz. The better‐than‐10‐dB impedance bandwidth of the antenna covers the 60‐GHz unlicensed band from 57 to 64 GHz. The 3‐dB beamwidths of the antenna are 105° and 76° at E‐plane and H‐plane at 60 GHz, respectively. The size of the die of the antenna is 2 mm × 4.5 mm. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:155–160, 2014.     

Novel offset‐fed dual‐band aperture‐dipole composite antenna: Operating principle and design approach

Operating principle and design approach of a novel dual‐band aperture‐dipole composite antenna are proposed. It is shown that multiple operating modes can be simultaneously excited by employing offset‐feeding technique at first. After the behavior of each mode is studied, the operating principle of the antenna is analyzed and described. Then, an improved dual‐band aperture‐dipole composite antenna is formed and it is designed by using the proposed approach. The antenna is experimentally verified. It is demonstrated that two operating bands for radiation are ranged from 2.36 to 2.58 GHz and from 4.1 to 15.72 GHz, respectively, in which the reflection coefficient are both 相似文献   

High gain substrate integrated waveguide beam scanning antenna with sub‐array elements

A method to enhance the gain of substrate integrated waveguide (SIW) beam scanning antenna is proposed in this article. 2 × 2 SIW cavity‐backed sub‐arrays are employed in array design. The antenna is constructed on two layers. The top layer places four SIW cavity‐backed sub‐arrays as radiating elements and the bottom layer is an SIW transmission line to feed the sub‐arrays. Beam scanning feature can be obtained due to the frequency dispersion. Moreover, through separating radiators to the other layer and using 2 × 2 SIW cavity‐backed sub‐arrays as radiating parts, the antenna gain is improved significantly. For a linear array, 4.1 to 6.8 dB gain enhancement is achieved compared to a conventional SIW beam scanning antenna with the same length. Then, the linear array is expanded to form a planar array for further gain improvement. A 64‐element planar beam scanning array is designed, fabricated, and tested. Experimental results show that the proposed planar array has a bandwidth from 18.5 GHz to 21. 5 GHz with beam scanning angle from ?5° to 11.5° and gain in the range of 20.5 to 21.8 dBi. The proposed high gain beam scanning antennas have potential applications in radar detection and imaging.     

一种宽频带复合天线设计

针对多系统载体天线数量多的问题,提出了一种基于印刷振子结构的宽频带共口径复合天线设计方法;通过两种不同形式的印刷偶极子进行共口径设计：采用平面印刷偶极子结构完成宽带高增益线极化天线,通过宽带定向耦合器实现了天线和差方向图辐射;采用十字印刷偶极子实现低增益天线的圆极化辐射;两种天线单元印刷在同一微波介质上,通过优化天线单元布局,相对位置关系和增加金属隔离环等措施,降低天线之间的相互影响,实现共口径复合天线性能满足工程应用要求;加工了天线样机,测试结果表明线极化天线在工作频带1.2～1.8 GHz范围内和差通道电压驻波比小于1.8,和通道增益大于13.5 dBi,方位差波束零值深度小于-25 dB,圆极化天线在工作频带1.2～1.8 GHz范围内电压驻波比小于1.6,增益大于6.5 dBi,轴比小于2.5 dB,与计算结果基本一致;复合天线可以满足多种无线通信系统的需求,减少了天线数量,有效节省载体平台空间,同时具有结构简单紧凑、剖面低、易于工程实现等特点,具有广阔的应用前景。     

Three‐dimensional printed wideband,dual‐cavity Ku‐band antenna

A novel three‐dimensional (3D) printed, wideband, and low cost bull's eye antenna is proposed and designed for Ku‐band applications. The proposed antenna covers entire Ku‐band satellite communication bands starting from 10.5 GHz to 14.5 GHz. The antenna structure consists of dual‐cavity radiating aperture surrounded by a circular groove. With the addition of cavity and corrugation, the antenna gain is increased more than 6 dB. The antenna is fabricated using 3D printing technology and conductive painting. Measurement results indicate that the antenna has 72% fractional bandwidth from 8 GHz to 17 GHz. Measured antenna peak gain is 13.5 dBi at 13 GHz and no less than 11.5 dBi throughout the entire Ku band.     

Miniaturized low‐profile antenna based on uniplanar quasi‐composite right/left‐handed metamaterial

In this article, a metamaterial‐based broadband low‐profile antenna is presented. The proposed antenna employed an array of uniplanar quasi‐composite right/left‐hand (CRLH) metamaterial cells. This structure contributes to exciting the operating modes in lower frequencies. The antenna has an overall electrical size of 0.75 × 0.60 × 0.07 λ₀³ (λ₀ is the center operating wavelength in free space) and provides a 25% measured bandwidth with the center frequency of 5.1 GHz and maximum gain of 6.6 dB. The proposed antenna is an appropriate candidate for WLAN, WiMAX, and other wireless communication applications.     

Dual‐polarized textile‐based two/four element MIMO antenna with improved isolation for dual wideband application

This article presents the designs of dual‐polarized dual wideband textile‐based two and four elements multiple‐input multiple‐output (MIMO) antennas for WLAN (IEEE 802.11a/b/g/c/n) and WiMAX (IEEE 802.16d) applications. These MIMO antennas cover the frequency spectra from 1.5 to 3.8 GHz (87% bandwidth) and 4.1 to 6.1 GHz (40% bandwidth). The characterization of the textile jeans substrate is determined experimentally using a vector network analyzer and dielectric assessment kit. These antennas provide near about 70% radiation efficiency with around 4 dBi peak gain in desired frequency ranges. The diversity performance is improved noticeably by printing meandered line structures on both planes. The proposed MIMO structure has a very low envelop correlation coefficient (ECC) <0.1 and high diversity gain (DG) >9.9. The Medium effective gain (MEG) also lies within a satisfactory value of ±3 dB. The two elements MIMO Antennas provide linear polarization at all desired frequency band while the four‐element antenna provides circular polarization at 2.4 GHz and linear polarization at 5.2 and 5.8 GHz application bands. The antenna also depicts good performance in wearable condition with safe specific absorption rate < 1.6 W/kg in all desired frequencies.     

Compact tri‐band MIMO antenna based on quarter‐mode slotted substrate‐integrated‐waveguide cavity

A compact tri‐band multiple‐input‐multiple‐output (MIMO) antenna based on a quarter‐mode slotted substrate‐integrated‐waveguide (SIW) cavity is proposed. By etching a wide slot, a single SIW cavity is divided into two sub‐cavities with the same size. They are fed by coaxial ports to form two MIMO elements and high antenna isolation can be achieved by this slot. To obtain multi‐band operations, two narrow slots are cut in the upper sub‐cavity and the other two slots are etched in the lower sub‐cavity. Three eighth‐mode resonances with different areas can simultaneously occur in these antenna elements. A prototype with the overall size of 0.34λ₀ × 0.34λ₀ has been fabricated. The measured center frequencies of three operating bands are 2.31, 2.91, and 3.35 GHz, respectively. The measured gain at above frequencies is 4.52, 4.29, and 4.57 dBi, respectively. Moreover, the measured isolation is higher than 16.7 dB within the frequency of interest.     

Complementary meander‐line‐inspired dielectric resonator multiple‐input‐multiple‐output antenna for dual‐band applications

The communication presents a simple dielectric resonator (DR) multiple‐input‐multiple‐output (MIMO) dual‐band antenna. It utilizes two “I”‐shaped DR elements to construct an “I”‐shaped DR array antenna (IDRAA) for MIMO applications. The ground plane of the antenna is defected by two spiral complementary meander lines and two circular ground slots. In the configuration, two “I”‐shaped DR elements are placed with a separation of 0.098λ. The antenna covers dual‐band frequency spectra from 3.46 to 5.37 GHz (43.26%) and from 5.89 to 6.49 GHz (9.7%). It ensures the C‐band downlink (3.7‐4.2 GHz), uplink (5.925‐6.425 GHz), and WiMAX (5.15‐5.35 GHz) frequency bands. Each DR element is excited with a 50‐Ω microstrip line feed with aperture‐coupling mechanism. The antenna offers very high port isolation of around 18.5 and 20 dB in the lower band and upper band, respectively. The proposed structure is suitable to operate in the MIMO system because of its very nominal envelope correlation coefficient (<0.015) and high diversity gain (>9.8). The MIMO antenna provides very good mean effective gain value (±0.35 dB) and low channel capacity loss (<0.35 bit/s/Hz) throughout the entire operating bands. Simulated and measured results are in good agreement and they approve the suitability of the proposed IDRAA for C‐band uplink and downlink applications and WiMAX band applications.     

High‐gain magnetic‐dipole quasi‐Yagi antenna using higher‐order‐mode dielectric resonator with near‐zero‐index metamaterial

For the first time, the rectangular dielectric resonator (DR) operating in higher‐order TE_3δ1 mode is investigated and used as a magnetic‐dipole driver to design quasi‐Yagi antenna with high gain. For further enhancing the antenna gain, a near‐zero‐index (NZI) metamaterial (NZIM) is proposed instead of the traditional directors and put in the front of DR driver. It is a simple structure and composed of a set of the parallel metallic lines printed on a substrate along the end‐fire direction. Benefiting from the higher‐order mode operation of the DR and NZIM, the realized gain of the proposed antenna can reach 10.3 dBi, including the gain improvement of 2 dBi resulting from the employed NZIM. To verify the design concept, the prototype of quasi‐Yagi DR antenna with NZIM is fabricated and characterized. The measured results agree very well with the simulated results.     

Modified circular common element four‐port multiple‐input‐multiple‐output antenna using diagonal parasitic element

A four‐port multiple input multiple‐output (MIMO) antenna with common radiating element is proposed for 2.4 GHz Wi‐Fi applications. It comprises a modified circular radiator fed by four identical modified feedlines, partial ground planes, and a diagonal parasitic element (DPE). The parasitic element is used to enhance the interport isolation. The antenna has a 2:1 Voltage standing wave ratio (VSWR) impedance band 2.34‐2.56 GHz and nearly omnidirectional radiation patterns. The radiation efficiency is more than 79% and gain is 2 dBi at resonant 2.43 GHz. The isolation in the given frequency band is 10 dB. At the 2.43 GHz, the isolation between adjacent ports (1, 2 and 1, 4) is 14 dB and between opposite ports (1, 3) is 12 dB. The mean effective gain (MEG) ≤ ?2.7 dB and envelope correlation coefficient is <0.01. The ?10 dB total active reflection coefficient bandwidth is 202 MHz. The antenna is designed for a Wi‐Fi device and the effectiveness of antenna has been checked for distance of ½ feet from the human head. The specific absorption rate (SAR) is found to be ≤0.17 W/Kg by CST simulation tool.     

Gain enhancement and mutual coupling reduction of multiple‐intput multiple‐output antenna for millimeter‐wave applications using two types of novel metamaterial structures

A method to significantly increase the gain and reduce the mutual coupling of microstrip multiple‐intput multiple‐output (MIMO) antenna based on metamaterial concept is presented. The μ‐negative and ε‐negative features of the proposed modified peace‐logo planar metamaterial (MPLPM) and two‐sided MPLPM (TSMPLPM) structures are calculated. The antenna structure consists of eight MPLPM slabs and two TSMPLPM, which are embedded in azimuth plane of a MIMO antenna vertically. The dimensions of MIMO antenna are 28 × 16 × 6.3 mm³ at 40 GHz. As a result, a compact MIMO antenna is simulated in comparison with primary microstrip structures. The corresponding return‐loss of the antenna is better than 10 dB over 34.5 to 45.5 GHz for Ka‐band applications. Good consent between the measured and simulated result is tacked. The maximum simulated gain of the structure is 15.5 dB at 40 GHz, creating a maximum gain improvement of 11.5 dB in comparison with a MIMO antenna without any metamaterial combinations. The value of the insertion‐loss (isolation) is 33 dB, which has improved by more than 25 dB compared to the conventional sample.