CO2 sorption performance by aminosilane functionalized spheres prepared via co‐condensation and post‐synthesis methods

Amine functionalized silica microspheres were synthesised via a modified Stöber reaction for carbon dioxide (CO₂) adsorption. A number of adsorbents were synthesized by co‐condensation and post synthesis immobilization of amines on porous silica spheres. CO₂ adsorption studies were carried out on a fixed bed gas adsorption rig with online mass spectrometry. Amine co‐condensed silica spheres were found to adsorb up to 66 mg CO₂ g^?1 solid in a 0.15 atm CO₂ stream at 35°C. Simple post‐synthesis addition of aminopropyltriethoxysilane to amine co‐condensed silica was found to significantly increase the uptake of CO₂ to 211 mg CO₂ g^?1 under similar conditions, with CO₂ desorption commencing at temperatures as low as 60°C. The optimum temperature for adsorption was found to be 35°C. This work presents a CO₂ adsorbent prepared via a simple synthesis method, with a high CO₂ adsorption capacity and favorable CO₂ adsorption/desorption performance under simulated flue gas conditions. © 2016 American Institute of Chemical Engineers AIChE J, 62: 2825–2832, 2016     

Ethane‐selective carbon composites CPDA@A‐ACs with high uptake and its enhanced ethane/ethylene adsorption selectivity

Novel composites (CPDA@A‐ACs) of carbonized polydopamine (CPDA) and asphalt‐based activated carbons (A‐ACs) were successfully synthesized, and characterized for adsorption separation of ethane/ethylene. The resulting CPDA@A‐ACs exhibited high Brunauer–Emmett–Teller surface area of 1971 m²/g. The O and N contents on CPDA@A‐ACs are higher than those on A‐ACs due to the introduction of CPDA. Interestingly, CPDA@A‐ACs exhibited great preferential adsorption of ethane over ethylene. Its ethane capacity reached as high as 7.12 mmol/g at 100 kPa and 25°C, and its ethane/ethylene adsorption selectivity became higher compared to A‐ACs, reaching as high as 3.0～20.6 below 100 kPa, significantly superior to the reported ethane‐selective adsorbents. Simulation results revealed the mechanism of enhanced selectivity toward C₂H₆/C₂H₄, and suggested that the surface oxygen functionalities of the composites play predominant role in enhancing ethane/ethylene adsorption selectivity. Fixed‐bed experiments showed that C₂H₆/C₂H₄ mixtures can be well separated at room temperature, suggesting great potential for industrial C₂H₆/C₂H₄ separation. © 2018 American Institute of Chemical Engineers AIChE J, 64: 3390–3399, 2018     

拟薄水铝石负载PEI/AMP吸附CO2性能

用富含胺基的物质对多孔材料进行修饰可以得到高CO₂吸附量的吸附剂。采用浸渍法将聚乙烯亚胺(PEI)和2-氨基-2-甲基-1-丙醇(AMP)负载在拟薄水铝石上,考察了CO₂压力、胺类物质负载量等对吸附性能的影响。采用低温N₂吸附/脱附法(BET)、扫描电镜(SEM)、傅里叶变换红外线光谱分析仪(FTIR)等手段表征了吸附剂的结构特征及其物理性质,并使用重量法微天平实验装置对吸附剂的性能进行了评价。实验结果表明,当温度恒定为50℃,压力小于1 MPa时,负载PEI的吸附剂最高的CO₂吸附量为77.53 mg CO₂·(g吸附剂)^-1,最佳负载量为85%;压力大于1 MPa时,负载PEI的吸附剂最高的CO₂吸附量为123.79 mg CO₂·(g吸附剂)^-1,最佳负载量为10%。负载AMP的吸附剂最高的CO₂吸附量为128.01 mg CO₂·(g吸附剂)^-1,最佳负载量为85%。CO₂吸附稳定性实验表明,吸附剂对CO₂的吸附性能稳定。     

Activation of carbon nanofibres for hydrogen storage

The present study was aimed to investigate different methods of activation of carbon nanofibres, CNF, in order to determine the beneficial effect on the hydrogen sorption capacities of increasing the surface area. Two activation systems were used: physical activation with CO₂ and chemical activation with KOH. A range of potential adsorbents were thus prepared by varying the temperature and time of activation. The structure of the CNF proved more suitable to activation by KOH than by CO₂, with the former yielding higher surface area carbons (up to 1000 m² g⁻¹). The increased surface area, however, did not correspond directly with a proportional increase in hydrogen adsorption capacity. Although high surface areas are important for hydrogen storage by adsorption on solids, it would appear that it is essential that not only the physical, but also the chemical, properties of the adsorbents have to be considered in the quest for carbon based materials, with high hydrogen storage capacities.     

N-containing activated carbons for CO2 capture

A series of SK-activated carbons were prepared by carbonising soya beans in the presence of KOH as activation agent. Different activation temperatures were applied to study the influence of preparation conditions on the surface properties of the carbons and their CO₂ adsorption capacity. It was found that the CO₂ adsorption capacity is directly related to the nature of surface basic N-containing groups and that the highest CO₂ adsorption capacity value was 4.24 mmol/g under 25°C and 1 atm.     

CO2 capture efficiency in post‐combustion using MWNT‐PAA in a packed bed column

The adsorption capacity of polyaspartamide (PAA) and multi‐wall carbon nanotubes with polyaspartamide (MWNT‐PAA) was investigated through a packed bed column with the flowing of flue gas composed of 15 % CO₂, 5 % O₂ and the balance N₂. The adsorption performed at 25 °C, 110 kPa and inlet gas flow rate of 60 mL/min resulted in high CO₂ adsorption capacity of 5.70 and 10.20 mmol‐CO₂/g for PAA and MWNT‐PAA, respectively. The adsorption kinetics was very high, so 7 min were enough for the effluent gas to reach the breakthrough after saturation. The consistency of adsorbents in recurring regeneration was successful through a continuous TSA system of 10 cycle adsorption‐desorption with temperatures of 25–100 °C. The evaluation of heat through differential scanning calorimetry (DSC) resulted in exothermic adsorption with heat release of 45.14 kJ/mol and 124.38 kJ/mol for PAA and MWNT‐PAA, respectively. The heat release was found favourable to promote the desorption as the temperature could rise after adsorption. This is an advantage for energy efficiency, as it depicts the potential of energy recovery. Thus, both adsorbent PAA and MWNT‐PAA were demonstrated to be promising for CO₂ adsorption capture in post‐combustion.     

Preparation and Phosphine Adsorption of Activated Carbon Prepared from Walnut Shells by KOH Chemical Activation

Walnut-shell activated carbons (WSACs) with high surface area and predominant micropore development were prepared by KOH chemical activation. The effects of carbonization temperature, activation temperature, and ratio of KOH to chars on the pore development of WSACs and PH₃ adsorption performance of the modified walnut-shell activated carbons (MWSACs) were studied. Criteria for determining the optimum preparation conditions were pore development of WSACs and PH₃ breakthrough adsorption capacity of MWSAC adsorbents. The result shows that the optimum preparation conditions are a carbonization temperature of 700°C, an activation temperature of 700°C, and a mass ratio of 3. The BET surface area and the micropore volume of the optimal WASC are 1636m²/g and 0.641cm³/g, respectively. The micropore volume percentage of WSAC plays an important role in PH₃ adsorption when there is a slight difference in BET surface areas. High-surface-area WSACs with predominant micropores are suitable for PH₃ adsorption removal. The MWSAC adsorbent owns the biggest PH₃ breakthrough adsorption capacity (284.12mg/g) due to the biggest specific surface area, total pore volume, and micropore volume percentage. The MWSAC adsorbent will be a potential adsorbent for PH₃ adsorption removal from yellow phosphorus tail gas.     

Application of polyethylenimine‐impregnated solid adsorbents for direct capture of low‐concentration CO2

A systematic study of CO₂ capture on the amine‐impregnated solid adsorbents is carried out at CO₂ concentrations in the range of 400–5000 ppm, relating to the direct CO₂ capture from atmospheric air. The commercially available polymethacrylate‐based HP2MGL and polyethylenimine are screened to be the suitable support and amine, respectively, for preparation of the adsorbent. The adsorbents exhibit an excellent saturation adsorption capacity of 1.96 mmol/g for 400 ppm CO₂ and 2.13 mmol/g for 5000 ppm CO₂. Moisture plays a promoting effect on CO₂ adsorption but depends on the relative humidity. The presence of O₂ would lead to the decrease of adsorption capacity but do not affect the cyclic performance. The diffusion additive is efficient to improve the adsorption capacity and cyclic performance. Moreover, the adsorbents can be easily regenerated under a mild temperature. This study may have a positive impact on the design of high‐performance adsorbents for CO₂ capture from ambient air. © 2014 American Institute of Chemical Engineers AIChE J, 61: 972–980, 2015     

Solution‐reprocessable microporous polymeric adsorbents for carbon dioxide capture

Solution‐processable microporous polymers are promising materials for CO₂ capture because of their low synthetic cost and high processability. In this work, we for the first time systematically evaluate the feasibility of two microporous polymers, namely PIM‐1 and its hydrolyzed form hPIM‐1, as adsorbent materials for postcombustion CO₂ capture. By conducting ternary CO₂/N₂/H₂O breakthrough experiments, PIM‐1 demonstrates several promising features: moderate CO₂ working capacity, low water vapor uptake capacity, good moisture resistance, and easy regeneration process. In addition, we have pioneeringly studied the multiple‐cycle CO₂ adsorption–desorption induced relaxation effect on soft PIM‐1 polymers. Through a simple dissolution–precipitation approach, PIM‐1 can restore its BET surface area, CO₂ uptake capacity, and pore‐size distribution. The solution reprocessability of PIM‐1 demonstrated in this study distinguishes it from other rigid adsorbents and thus offers a new insight for the future design of economically‐viable and facilely regenerable adsorbents. © 2018 American Institute of Chemical Engineers AIChE J, 64: 3376–3389, 2018     

Preparation of Activated Carbons from Tobacco Stems by Potassium Hydroxide Activation and Phosphine Adsorption

Activated carbon preparation from tobacco stems by KOH activation at different activation temperatures and KOH/char mass ratios were investigated in this study. The effects of preparation parameters on activated carbon pore structure, morphometrics, microcrystallinities, and surface functional groups were characterized by N₂ adsorption, SEM, XRD, and FTIR technologies, respectively. The optimum preparation condition of activated carbon was activation temperature of 850°C, and KOH/char mass ratio of 2. Under this condition, the BET surface area of 2215 m²/g, and the pore volume of 1.343 cm³/g can be obtained. Prepared activated carbon showed clearly honeycomb holes, and a predominated amorphous structure. With increase of activation temperature and KOH/char mass ratio, decrease of surface oxygen functional group, and aromatization of the carbon structure was found. The activated carbon was subject to PH₃ purification, and the maximum PH₃ adsorption capacity of 253 mg/g can be realized based on well prepared KOH-AC with modification of 2.5% Cu. It seems that the activated carbon produced from chemical activation of tobacco stem would be an effective and alternative adsorbent for PH₃ adsorption because of its high surface area, adsorption capacity, and low cost.     

Adsorption of CO<Subscript>2</Subscript> by iron-exchanged heteropolyacid Fe<Subscript>1.5</Subscript>PMo<Subscript>12</Subscript>O<Subscript>40</Subscript> supported on mesoporous cellular foams

Novel low-temperature swing adsorbents that preferably adsorb CO₂ were synthesized by varying loading of heteropolyacid Fe_1.5PMo₁₂O₄₀ (Fe–PMA) supporting on mesoporous cellular foams (MCFs) by wetting impregnation. The synthesized materials were characterized by various physicochemical, thermal and spectral techniques and the CO₂ adsorption capacity of the materials were evaluated. Solid adsorbents showed a significantly high adsorption capacity toward CO₂ due to the chemisorptions of CO₂. The CO₂ adsorption capacities of the materials decreased as the temperature increased. The results showed that the adsorption capacity reached a level of 81.8 mg CO₂/g-adsorbent at 25 °C for the 20 wt% Fe–PMA–MCFs. These results indicated that the iron (Fe²⁺) complexes acted as efficient catalysts for the separation of CO₂. The as-synthesized adsorbents were selective, thermally stable, long-lived, and could be recycled at a temperature of 110 °C.     

Pebax–polydopamine microsphere mixed‐matrix membranes for efficient CO2 separation

Novel facilitated‐transport mixed‐matrix membrane (MMM) were prepared through the incorporation of polydopamine (PDA) microspheres into a poly(amide‐b‐ethylene oxide) (Pebax MH 1657) matrix to separate CO₂–CH₄ gas mixtures. The Pebax–PDA microsphere MMMs were characterized by Fourier transform infrared spectroscopy, scanning electron microcopy, X‐ray diffraction, differential scanning calorimetry, and thermogravimetric analysis. The PDA microspheres acted as an adhesive filler and generated strong interfacial interactions with the polymer matrix; this generated a polymer chain rigidification region near the polymer–filler interface. Polymer chain rigidification usually results in a larger resistance to the transport of gas with a larger molecular diameter and a higher CO₂–CH₄ selectivity. In addition, the surface of PDA microspheres contained larger numbers of amine, imine, and catechol groups; these were beneficial to the improvement of the CO₂ separation performance. Compared with the pristine Pebax membrane, the MMM with a 5 wt % PDA microsphere loading displayed a higher gas permeability and selectivity; their CO₂ permeability and CO₂–CH₄ selectivity were increased by 61 and 60%, respectively, and surpassed the 2008 Robeson upper bound line. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44564.     

Highly efficient and reversible CO2 capture by tunable anion‐functionalized macro‐porous resins

Anion functionalized strategy has been proposed for the synthesis of macro‐porous resins [IRA‐900][An] through the neutral reaction of the basic resin [IRA‐900][OH] with the corresponding donors. Combining CO₂ adsorption results and FT‐IR, solid‐state ¹³C NMR characterization as well as quantum chemical calculations, chemical adsorption mechanism was verified and tunable capture of CO₂ was realized. Among them, the anion functionalized resin [IRA‐900][Triz] exhibits an extremely high adsorption capacity (4.02 mmol g^?1 at 25°C, 0.15 bar), outperforming many other good adsorbents. Finally, we discuss the thermostability and recycling stability of [IRA‐900][Triz], which shows a great potential in the industrial capture of CO₂. © 2017 American Institute of Chemical Engineers AIChE J, 63: 3008–3015, 2017     

Aminating modification of viscose fibers and their CO2 adsorption properties

An adsorbent for CO₂ capture was prepared by the grafting of acrylonitrile (AN) onto viscose fibers (VFs); this was followed by amination with triethylene tetramine (TETA). The effects of the reaction conditions, such as the concentrations of the monomer, initiator, and nitric acid, on the grafting degree and grafting efficiency were studied. The adsorption performance of the adsorbent for CO₂ was evaluated by fixed‐bed adsorption. The highest dynamic adsorption capacity of the adsorbent for CO₂ was 4.35 mmol/g when the amine content of the adsorbent VF–AN–TETA reached 13.21 mmol/g. Compared with the polypropylene (PP)‐fiber‐based adsorbent (PP–AN–TETA), VF–AN–TETA with hydroxyl groups on the fibers facilitated the diffusion of CO₂ and water and led to a higher CO₂ adsorption capacity than that of PP–AN–TETA. The VF–AN–TETA adsorbent also showed good regeneration performance: its CO₂ adsorption capacity could still retain almost the same capacity as the fresh adsorbent after 10 adsorption–desorption cycles. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42840.     

Porous structure and adsorptive properties of pineapple peel based activated carbons prepared via microwave assisted KOH and K2CO3 activation

The present research explores the feasibility of microwave irradiation for preparation of high surface area activated carbon from pineapple peel (PPAC), an agricultural effluent emitted from the food can processing industries via KOH and K₂CO₃ activation. The activation process was performed at the microwave power of 600 W and irradiation time of 6 min. The equilibrium behavior of PPAC was investigated by performing batch adsorption experiments using methylene blue as adsorbate. Nonlinear adsorption isotherm models, Langmuir, Freundlich and Temkin were used to simulate the equilibrium data. KOH activated sample demonstrated a better development of pore structure, with the BET surface area, total pore volume and average pore size of 1006 m²/g, 0.59 m³/g and 23.44 Å, respectively, while the monolayer adsorption capacity of methylene blue was determined to be 462.10 mg/g. The findings support the potential use of microwave assisted KOH and K₂CO₃ activation as a promising activation technique.     

Amine modified mesocellular siliceous foam (MCF) as a sorbent for CO2

Adsorption is considered a promising method for carbon capture. CO₂ adsorbents take a variety of forms - but one approach is to fill mesoporous substrates with a polymeric CO₂ selective sorbent. SBA-15 and mesocellular siliceous foam (MCF) are high pore volume, high surface area ordered mesoporous materials for which modification with amine should result in high capacity, highly selective adsorbents. SBA-15 and MCF were separately loaded with approximately one pore volume equivalent of linear polyethyleneimine (PEI) (M_w = 2500) or branched PEI (M_n = 1200). CO₂ adsorption/desorption isotherms under dry CO₂ were obtained at 75, 105 and 115 °C. The CO₂ adsorption/desorption kinetics were improved with temperature, though the CO₂ capacities generally decreased. The adsorption capacity for MCF loaded with branched PEI at 105 and 115 °C were 151 and 133 mg/g adsorbent, respectively (in 50% CO₂/Ar, 20 min adsorption time). These are significantly higher than the adsorption capacity observed for SBA-15 loaded with branched PEI under same conditions, which were 107 and 83 mg/g adsorbent, respectively. Thus the results indicate that, on a unit mass basis, amine modified MCF's are potentially better adsorbents than amine modified SBA-15 for CO₂ capture at modestly elevated temperature in a vacuum swing adsorption process.     

Amine‐functionalization of the nanotitanate ETS‐2

A series of nonporous, amine‐functionalized sodium titanates was prepared and the thermal and adsorptive behavior of the samples were characterized. Engelhard titanosilicate 2 was chosen as a substrate for its high surface area (～300 m²/g), native surface hydroxyl concentration, and lack of microporosity; eliminating the risk of fouling the adsorbent under certain process conditions. Aminosilanes containing a single (N1), two (N2), and three (N3) amine groups were chemically grafted to the surface of the substrate and the adsorption capacity for CO₂ measured through thermogravimetry‐mass spectroscopy (TG‐MS) desorption, volumetric adsorption, and gravimetric adsorption/desorption cycling. The N3 sample displayed complete monolayer coverage and was capable of adsorbing five times as much atmospheric CO₂ as the N1 sample. Testing under anhydrous conditions only engages the primary amine on the tether and the data consistently suggests a correlation between amine utilization and the proportion of monolayer coverage for these adsorbents. © 2013 American Institute of Chemical Engineers AIChE J, 59: 4727–4734, 2013     

Properties of adsorbents prepared by the alkali activation of Aleksandriisk brown coal

Highly microporous adsorbents (micropore fraction of ～70%) were prepared by the alkali activation-thermolysis (800°C, 1 h) of brown coal (C ^daf = 70.4%) in the presence of potassium hydroxide at the KOH/coal weight ratio R _KOH ≤ 2.0 g/g. The dependences of the specific surface areas and adsorption capacities of the adsorbents for methylene blue (A_MB, mg/g), iodine (A_I, mg/g), and hydrogen (\(A_{H_2 } \), wt %) on R _KOH were determined. The adsorbents obtained at R _KOH ≥ 1.0 g/g exhibited developed specific surface areas and good adsorption characteristics (A_I = 1000–1200 mg/g, A_MB = 200–250 mg/g, and \(A_{H_2 } \) ≤ 3.16 wt % at 0.33 MPa). The high capacity for hydrogen allowed us to consider brown coal adsorbents as promising materials for use as hydrogen accumulators.     

Preparation and characteristics of rice-straw-based porous carbons with high adsorption capacity

To prepare porous carbons with high adsorption capacity from rice straws, two different kinds of precursors, i.e. one as the raw rice straws (one-stage process) and the other as pre-carbonized rice straws (two-stage process), were activated with KOH of various impregnation ratios. The two-stage process was found very effective for manufacturing porous carbons with high surface area and adsorption capacities for MB and I₂. For example, the porous carbon that was carbonized at 700°C and subsequently activated at 900°C exhibited the surface area of 2410 m²/g, the adsorption capacities of 800 and 1720 mg/g for MB and I₂, respectively, and the total pore volume of 1.4 ml/g. In the two-stage method, there was a preferential optimum impregnation ratio of KOH to a precursor carbon, i.e. 4:1, with which high surface area of porous carbons could be achieved. The formation of uni- and bidentate carboxylic salt structure, induced by reaction between KOH and oxygen containing carbon, that facilitates the formation of azo group (-NN-) on a subsequent heat treatment was considered as one of the key factors for the presence of optimum impregnation ratio of KOH. In contrast, the porous carbons of only moderate adsorption capacity could be obtained from the one-stage method. The original morphology of rice straw was sustained during the two-stage process, yet not during the one-stage process.     

Enhancement of CO2 adsorption on phenolic resin-based mesoporous carbons by KOH activation

Carbons with high surface area and large volume of ultramicropores were synthesized for CO₂ adsorption. First, mesoporous carbons were produced by soft-templating method using triblock copolymer Pluronic F127 as a structure directing agent and formaldehyde and either phloroglucinol or resorcinol as carbon precursors. The resulting carbons were mainly mesoporous with well-developed surface area, large total pore volume, and only moderate CO₂ uptake. To improve CO₂ adsorption, these carbons were subjected to KOH activation to enhance their microporosity. Activated carbons showed 2–3-fold increase in the specific surface area, resulting from substantial development of microporosity (3–5-fold increase in the micropore volume). KOH activation resulted in enhanced CO₂ adsorption at 760 mmHg pressure: 4.4 mmol g⁻¹ at 25 °C, and 7 mmol g⁻¹ at 0 °C. This substantial increase in the CO₂ uptake was achieved due to the development of ultramicroporosity, which was shown to be beneficial for CO₂ physisorption at low pressures. The resulting materials were investigated using low-temperature nitrogen physisorption, CO₂ sorption, and small-angle powder X-ray diffraction. High CO₂ uptake and good cyclability (without noticeable loss in CO₂ uptake after five runs) render ultramicroporous carbons as efficient CO₂ adsorbents at ambient conditions.