Si4+和F-掺杂对LiNi1/3Co1/3Mn1/3O2结构和电化学性能的影响

以Li2CO3、NiO、Co2O3、MnO2、LiF和SiO2为原料,采用机械力活化固相法制备了Si4+和F-掺杂的锂离子电池正极材料LiNi1/3Co 1/3Mn1/3O2.通过X射线衍射(XRD)、扫描电镜(SEM)和电化学性能测试等技术研究了LiNi1/3Co1/3Mn1/3O2的结构特征、形貌及电化学性能等.结...     

层状LixNi1/3Mn1/3Co1/3O2阴极材料的结构、电化学与热稳定性

用NO2BF4作为脱锂剂,通过化学反应定量脱去材料中的锂离子,合成出不同嵌锂量的LixNi1/3Mn1/3-Co1/3O2(0≤x≤1)系列材料.通过电感耦合等离子体质谱(ICP-MS)、光电子能谱(XPS)、X射线衍射(XRD)、循环伏安(CV)等方法表征手段发现,当锂脱出量超过总量的49%后,材料的结构、过渡金属的价态、电化学性能等方面都发生显著变化,这些变化中的不可逆因素影响了其首次充放过程的可逆性.结合TPD-MS以及TG分析,结果表明,在脱锂过程中晶格氧的活性增强,更加容易在较低温度下脱出,影响了材料的热稳定性.     

Li(Ni1/3Co1/3Mn1/3)O2/Ag电极材料的制备及电化学性能

以碳酸盐为沉淀剂,采用共沉淀法合成晶型良好的亚微米级Li(Ni1/3Co1/3Mn1/3)O2粉末,并将其与AgNO3复合,采用无电流分解沉积法制备出了Ag表面修饰的Li(Ni1/3Co1/3Mn1/3)O2/Ag电极材料.利用X-射线衍射、扫描电镜及电化学测试等方法表征材料的结构、形貌和电化学性能.结果表明:Ag单质的存在可明显改善Li(Ni1/3Co1/3Mn1/3)O2的电化学性能,尤其是倍率特性,以0.2C、0.5C、1C倍率放电进行测试,经过40次循环后比容量分别为156.2、144.3、137.7mAh·g-1,其容量保持率分别为96.2％、95.3％、93.9％.Ag的表面修饰能使Li(Ni1/3Co1/3Mn1/3)O2电荷转移阻抗大幅度减小,阻抗从65Ω减小到50Ω.     

层状LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2正极材料的多元掺杂改性

采用共沉淀法制备锂离子电池掺杂型层状LiNi1/3Co1/3Mn1/3-xMxO2(M=Mg、Al、Cr)正极材料。采用X射线衍射、扫描电镜、充放电实验和交流阻抗实验对LiNi1/3Co1/3Mn1/3-xMxO2正极材料的结构、形貌、电化学性能以及动力学参数进行表征。结果表明:当掺杂量x=0.05时,Mg2+、Al3+掺杂的正极材料在2.8～4.3V、0.1C下的首次放电比容量分别为139.2、151.6mA·h/g,20次循环后的容量保持率分别为98.8%和96.7%;掺杂Mg2+或Al3+均能提高LiNi1/3Co1/3Mn1/3O2的交换电流密度和锂离子扩散系数。结合实验结果和掺杂离子的离子半径和化学稳定性,解释了掺杂离子在LiNi1/3Co1/3Mn1/3O2晶格中的占位及其在充放电过程中的作用。     

La_(2/3)Ba_(1/3)MnO_3∶Ag_x多晶靶材制备及其性能

采用化学共沉淀法制备了不同Ag掺杂量的La2/3Ba1/3MnO3∶Agx(x为摩尔分数,x=0.00、0.02、0.08、0.10、0.20)多晶靶材,通过XRD、SEM和R-T对La2/3Ba1/3MnO3∶Agx靶材的结构和性能进行测试分析,实验结果表明:所得样品为正交晶系钙钛矿结构;掺Ag(x=0.02、0.08、0.10、0.20)样品比未掺Ag样品的金属-绝缘转变温度Tp值低;随着烧结温度和Ag掺杂量的升高,金属-绝缘转变温度Tp随之增加;随着Ag掺杂量增加,电阻率归一化值先增大后减小。La、Ba、Mn元素的摩尔分数与理论设计的数值基本相同,O元素在烧结过程中缺失较严重,Ag元素的摩尔分数也较低,这与Ag在高温烧结时的挥发有关。     

La2/3Ca1/3MnO3∶Ag0.4与La2/3Ba1/3MnO3∶Ag0.4的制备及其性能研究

采用化学共沉淀法合成制备了Ag掺杂摩尔百分比为0.4的La2/3Ca1/3MnO3∶Ag0.4 (LCMO∶Ag0.4)、La2/3Ba1/3MnO3∶Ag0.4(LBMO∶Ag0.4)多晶复合材料,通过XRD和R-T分别对两种材料的结构和性能进行测试分析.实验结果表明:所得样品均为正交晶系钙钛矿结构;LCMO∶Ag0.4的金属-绝缘转变温度(Tp=280.2 K)比LBMO∶Ag0.4要高(Tp=256.8 K);LCMO:Ag0.4样品的电阻值比LBMO∶Ag0.4要小两个数量级;LCMO∶Ag0.4的TCR最大值为28％,要远远高于LBMO∶Ag0.4的TCR最大值(0.5％).     

低冰镍衍生的具有高结构稳定性和快速扩散动力学的钠离子掺杂层状LiNi1/3Co1/3Mn1/3O2正极(英文)

通过共沉淀法合成钠离子(Na⁺)掺杂的高稳定性Li_1-xNa_xNi_1/3Co_1/3Mn_1/3O₂(NCM-Na)正极材料。首先论证采用低冰镍提取镍作为合成材料镍源的可行性。其次,在化学试剂合成的NCM(Ni,Co,Mn)材料中预先引入最优含量的Na⁺,占据部分Li⁺位点,实现具有更低Li⁺/Ni²⁺阳离子混排的稳定结构,从而提高其电化学性能。结果表明,当Na⁺掺杂量为1%(质量分数)(x=0.01)时,获得的NCM-Na正极材料在1C电流密度下,循环100次后容量保持率从76.84%提高至89.21%。特别是在5C大电流密度下,循环200次后,可逆放电比容量依然维持在110 mA·h·g^-1。这为杂原子掺杂耦合材料化冶金开发低成本、高性能锂离子电池三元LiNi_1/3Co_1/...     

Zn掺杂对LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2结构与电化学性能的影响

用溶胶凝胶法制备了Li Ni1/3Co1/3-x Mn1/3Znx O2(x=0,1/24,2/24,4/24)锂离子电池正极材料。由X射线衍射和扫描电镜对其分析结果表明,Zn掺杂不改变Li Ni1/3Co1/3Mn1/3O2的α-Na Fe O2层状结构,当掺杂量达到4/24时,杂相产生。电化学研究表明,当Zn掺杂量为2/24时,Li Ni1/3Co1/3Mn1/3O2首次放电容量由未掺杂的169.2 m Ah·g-1降低为160.1m Ah·g-1,但循环性能明显提高,30次循环后的容量保持率由未掺杂的89.2%升至97%。并且在20、40、60和80 m A·g-1不同的电流密度下继续循环20次后,当再次恢复到20 m A·g-1的电流密度时,放电容量可恢复到150.3 m Ah·g-1。     

锂离子电池正极材料LiNi_1/3Co_1/3Mn_1/3O_2的研究进展

介绍了一种新型的锂离子电池正极材料LiNi1/3Co1／3Mn1／3O2的最新研究状况,描述了材料的晶体及电子结构,以及电化学性能;重点总结了现今国内外制备此材料的几种主要合成方法及研究进展;同时,介绍了不同掺杂元素（Fe、B、Al、Ti）对材料的改性作用。     

LiOH-Li_2CO_3低共熔混合锂盐体系合成LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2

利用低共熔组成的0.24LiCO3-0.76LiOH混合锂盐体系,与钴、镍、锰的球形氢氧化物按1.1:1混合,无需前期球磨,直接经二段控温程序制备出锂离子正极材料LiNi1/3Co1/3Mn1/3O2。X射线衍射分析表明合成的Li(Ni1/3Co1/3Mn1/3)O2结晶度高,具有规整的层状α-NaFeO2结构,扫描电镜显示产物颗粒均匀,振实密度高达2.89g·cm-3,显著高于用单一锂盐制备的同样产品(2.4g·cm-3)。充放电测试表明,材料具有良好的电性能,首次充放电容量为176和166mhA·g-1,循环50次后,材料的电性能没有明显的衰减。     

Surface modification of spherical LiNi1/3Co 1/3 Mn1/3O2 with Al2O3 using heterogeneous nucleation process

To improve the cycle stability at high voltage and high charge/discharge rate, spherical LiNi1/3Co1/3Mn1/3O2 was coated with Al2O3 by using heterogeneous nucleation process, and the physical and electrochemical properties were studied. The SEM images show that there is a uniform coating on the modified spherical LiNi1/3Co1/3Mn1/3O2. The electrochemical tests indicate that the properties of LiNi1/3Co1/3Mn1/3O2 coated with 0.5% aluminum oxide are the best. The initial capacities are 150 and 173 mA.h/g at the rate of I C in the voltage range of 2.7-4.3 V and 2.7-4.6 V, respectively, and the discharge capacities maintain about 99% and 85% after 30 cycles, respectively. While those of the bare LiNi1/3Co1/3Mn1/3O2 are only 90% and 75%, respectively. The CV tests of LiNi1/3Co1/3Mn1/3O2 show that Al203-coating can restrain the oxide-reduction peak currents fading during the charge/discharge course.     

Uniform AlF3 thin layer to improve rate capability of LiNi1/3Co1/3 Mn1/3O2 material for Li-ion batteries

LiNi1/3Co1/3Mn1/3O2 was coated with uniform nano-sized AlF3 layer by chemical precipitation method to improve its rate capability. The samples were characterized by X-ray diffractometry (XRD), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), charge-discharge cycling, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). Uniform coated layer with a thickness of about 3 nm was observed on the surface of LiNi1/3Co1/3Mn1/3O2 particle by TEM. At 0.5C and 2C rates, 1.5% (mass fraction) AlF3-coated LiNi1/3Co1/3Mn1/3O2/Li in 2.8-4.3 V versus Li/Li+ after 80 cycles showed less than 3% of capacity fading, while those of the bare one were 16.5% and 45.9%, respectively. At 5C rate, the capacity retention of the coated sample after 50 cycles maintained 91.4% of the initial discharge capacity, while that of the bare one decreased to 52.6%. EIS result showed that a little change of charge transfer resistance of the coated sample resulting from uniform thin AlF3 layer was proposed as the main reason why its rate capability was improved obviously. CV result further indicated a greater reversibility for the electrode processes and better electrochemical performance of AlF3-coated layer.     

Synthesis and electrochemical characterization of layered Li[Ni1/3CO1/3 Mn1/3]O2 cathode material for Li-ion batteries

1 INTRODUCTIONDue to the high cost of LiCoO2,a commonlyused cathode material in commercial rechargeablelithium-ion batteries , much efforts have been madeto develop cheaper cathode materials than LiCoO2,Li Ni O2and Li MnO2have been studied extensivelyas possible alternatives to LiCoO2[1 4 ]. Stoichio-metric Li Ni O2is knownto be difficult to synthesizeandits multi-phase reaction during electrochemicalcyclingleads to structural degradation,andlayeredLi MnO2has a significant drawback…     

Al2O3包覆LiNi0.03Co0.05Mn1.92O4正极材料的制备及其电化学性能

以Al(NO3)3?9H2O为包覆原料,通过燃烧法制备得到LiNi0.03Co0.05Mn1.92O4@Al2O3正极材料。通过X射线衍射(XRD),场发射扫描电子显微镜(FESEM)和透射电镜(TEM)等表征手段对材料的结构和形貌进行分析,并通过恒电流充放电、循环伏安(CV)、交流阻抗(EIS)等测试分析材料的电化学性能。结果表明,Al2O3包覆没有改变LiNi0.03Co0.05Mn1.92O4的尖晶石型结构,包覆层厚度约10.6nm。LiNi0.03Co0.05Mn1.92O4@Al2O3正极材料电化学性能得到了明显改善,1 C和10 C倍率下初始放电比容量分别为119.9 mAh?g-1和106.3 mAh?g-1,充放电循环500次后容量保持率分别为88.4%和78.2%,而未包覆的LiNi0.03Co0.05Mn1.92O4在1 C和10 C倍率下初始放电比容量分别为121.2 mAh?g-1和104.0 mAh?g-1,500次循环后容量保持率分别为84.1%和67.6%。LiNi0.03Co0.05Mn1.92O4@Al2O3活化能为32.92 kJ?mol-1,而未包覆材料的活化能为36.24 kJ?mol-1,包覆有效降低了材料Li+扩散所需克服的能垒,提高了材料的电化学性能。     

LiNi1/3Co1/3Mn1/3O2和LiNi3/8Co1/4Mn3/8O2纳米纤维的合成与电化学性能

以溶胶前驱体为纺丝液,通过静电纺丝法合成锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2和LiNi3/8Co1/4Mn3/8O2纳米纤维.采用原子力显微镜(AFM)、X射线衍射(XRD)、充放电实验对纳米纤维的形貌、结构和电化学性能进行研究.结果表明,纳米纤维的直径在150～200 nm之间,且具有典型的α-NaFeO2层状结构.LiNi1/3Co1/3Mn1/3O2和LiNi3/8Co1/4Mn3/8O2纳米纤维的首次放电容量均超过170 mAh·g-1,50次循环后容量保持率在90%以上.     

Effects of synthesis conditions on the structural and electrochemical properties of layered LiNi1/3Co1/3Mn1/3O2 cathode material via oxalate co-precipitation method

The uniform layered LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion batteries was prepared by using (Ni1/3Co1/3Mn1/3)C2O4 as precursor synthesized via oxalate co-precipitation method in air. The effects of calcination temperature and time on the structure and electrochemical properties of the LiNi1/3Co1/3Mn1/3O2 were systemically studied. XRD results revealed that the optimal calcination conditions to prepare the layered LiNi1/3Co1/3Mn1/3O2 were 950°C for 15 h. Electrochemical measurement showed that the sample prepared under the such conditions has the highest initial discharge capacity of 160.8 mAh/g and the smallest irreversible capacity loss of 13.5% as well as stable cycling performance at a constant current density of 30 mA/g between 2.5 and 4.3 V versus Li at room temperature.     

前处理工艺对Li[Ni1/3Mn1/3Co1/3]O2正极材料结构、形貌和电化学性能的影响（英文）

以[Ni1/3Co1/3Mn1/3]3O4和氢氧化锂为原料,分别采用球磨法和液相法前处理工艺制备层状正极材料Li[Ni1/3Mn1/3Co1/3]O2。采用X？射线衍射（XRD）、场发射扫描电镜（FESEM）、恒流充放电等手段对材料的物理和电化学性能进行表征。结果表明：采用不同前处理工艺制备出的Li[Ni1/3Mn1/3Co1/3]O2材料在结构、形貌和电化学性能上有较大差异;与球磨处理法制备的材料相比,采用液相法前处理工艺制备的Li[Ni1/3Mn1/3Co1/3]O2不但保持了前驱体较好的球形形貌,同时还具有较好的循环稳定性和倍率性能;该样品在20mA/g电流密度下,首次放电容量为178mA·h/g,50次循环后,容量保持率达98.7%;在1000mA/g电流密度下,样品容量为135mA·h/g。     

Zn对锂电池材料LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2结构和电化学性能的影响

采用共沉淀法掺入少量Zn得到Li(Ni1/3Co1/3Mn1/3)1-xZnxO2材料。通过X射线衍射、光电子能谱(XPS)和电化学测试研究掺杂对其晶体结构、元素价态和电化学行为的影响。结果表明:掺入Zn增大晶格常数;在粉末颗粒表面的Zn含量是颗粒内部的数十倍;掺杂后Co、Mn依然保持+3、+4价,但是Ni由+2、+3混合价态组成;掺入少量Zn阻止电极在4.5V电位下的不可逆氧化反应;掺入Zn有效改善高截止电压下的循环容量保持能力,其作用与改变材料表面状态有关。