Preparation and properties of the single‐walled carbon nanotube/cellulose nanocomposites using N‐methylmorpholine‐N‐oxide monohydrate

Single‐walled carbon nanotube (SWNT)/cellulose nanocomposite films were prepared using N‐methylmorpholine‐N‐oxide (NMMO) monohydrate as a dispersing agent for the acid‐treated SWNTs (A‐SWNTs) as well as a cellulose solvent. The A‐SWNTs were dispersed in both NMMO monohydrate and the nanocomposite film (as confirmed by scanning electron microscopy) because of the strong hydrogen bonds of the A‐SWNTs with NMMO and cellulose. The mechanical properties, thermal properties, and electric conductivity of the nanocomposite films were improved by adding a small amount of the A‐SWNTs to the cellulose. For example, by adding 1 wt % of the A‐SWNTs to the cellulose, tensile strain at break point, Young's modulus, and toughness increased ～ 5.4, ～ 2.2, and ～ 6 times, respectively, the degradation temperature increased to 9°C as compared with those of the pure cellulose film, and the electric conductivities at ? (the wt % of A‐SWNTs in the composite) = 1 and 9 were 4.97 × 10^?4 and 3.74 × 10^?2 S/cm, respectively. Thus, the A‐SWNT/cellulose nanocomposites are a promising material and can be used for many applications, such as toughened Lyocell fibers, transparent electrodes, and soforth. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Rheological characterization of cellulose solutions in N‐methyl morpholine N‐oxide monohydrate

Three different modes of rheological properties were measured on 11 and 13 wt % solutions of cellulose in N‐methyl morpholine N‐oxide (NMMO) monohydrate, in which concentration range lyocell fibers of much reduced fibrillation are preferably produced. The dynamic rheological responses revealed that the Cox–Merz rule did not hold for these cellulose solutions. Both cellulose solutions showed a shear thinning behavior over the shear rate measured at 85, 95, 105, and 115°C. However, 13 wt % solution gave rise to yield behavior at 85ºC. The power law index ranged from 0.36 to 0.58. First normal stress difference (N₁) was increased with lowering temperature and with increasing concentration as expected. Plotting N₁ vs shear stress (τ_ω) gave almost a master curve independent of temperature and concentration, whose slope was about 0.93 for both cellulose solutions over the shear rate range observed (τ_ω > 500 Pa). In addition, the cellulose solutions gave high values of recoverable shear strain (S_R), ranging from 60 to 100. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 216–222, 2002     

Blend films of O‐carboxymethyl chitosan and cellulose in N‐methylmorpholine‐N‐oxide monohydrate

To introduce N‐methylmorpholine‐N‐oxide (NMMO) process to prepare antibacterial lyocell fiber, the blend films of O‐carboxymethyl chitosan (O‐CMCS) and cellulose were prepared. O‐CMCS in aqueous suspension with particles having a surface mean diameter of 2.24 μm was blended with cellulose in NMMO hydrate. The blend films with different O‐CMCS content were prepared with the blend solutions. SEM confirmed that O‐CMCS remained within the cellulose film in the particle. The mechanical properties of the blend films show little increased value when O‐CMCS was less 5%; however, it decreased sharply when O‐CMCS was over 8%. Thus, the optimum O‐CMCS content may give a good combination of antibacterial action and mechanical properties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4601–4605, 2006     

Cellulose nanofibers prepared by the N‐methylmorpholine‐N‐oxide method

The process of electrospinning is very suitable for obtaining fibers with a diameter on a nanometer scale. Such fibers can be spun from almost all kinds of known polymers, copolymers, and polymer blends. In this work, we present cellulose nanofibers obtained by the electrospinning process from spinning dopes containing cellulose dissolved in an N‐methylmorpholine‐N‐oxide/water system. Under different electrospinning process conditions, cellulose fibers, a nonwoven fiber network, and a cellulose membrane were obtained. The fibers were examined with scanning electron microscopy. The diameters of the fibers were in the submicrometer range. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1855–1859, 2005     

Physical agglomeration behavior in preparation of cellulose‐N‐methyl morpholine N‐oxide hydrate solutions by simple mixing

The different melting temperatures of N‐methyl morpholine N‐oxide (NMMO) hydrates in the cellulose–NMMO hydrate solution may be explained by the rather different crystal structures of NMMO hydrates, which are determined by the amount of the hydrates. The preparative process of cellulose–NMMO hydrate solution may result in cellulose structural change from cellulose I to cellulose II, depending on the amount of the hydrate. Mixtures of cellulose and NMMO hydrate in a blender was changed from the granules to slurry with increasing mixing time at 60–70°C, which is below the melting point of the NMMO hydrate. In the case of 15 wt % cellulose–NMMO hydrate granules, which were made by mixing for 20 min, the melting points of various NMMO hydrates were obtained as 77.8°C (n = 0.83), 70.2°C (n = 0.97), and 69.7°C (n = 1.23), respectively, depending on the hydrate number. However, the melting points of cellulose–NMMO hydrate slurry and solution were shifted lower than those of cellulose granules, while the mixing time of slurry and solution are 25 and 35 min, respectively. These melting behaviors indicate instantaneous liquefaction of the NMMO hydrate and the diffusion of the NMMO hydrate into cellulose during mixing in a blender. When cellulose was completely dissolved in NMMO hydrate, the crystal structure of cellulose showed only cellulose II structure. In the cellulose–NMMO products of granules or slurry obtained by high‐speed mixing, which is a new preparation method, they still retained the original cellulose I structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1687–1697, 2004     

Hemodialysis membrane prepared from cellulose/N‐methylmorpholine‐N‐oxide solution. II. Comparative studies on the permeation characteristics of membranes prepared from N‐methylmorpholine‐N‐oxide and cuprammonium solutions

Two kinds of regenerated cellulose membranes for hemodialysis were prepared from casting solutions of N‐methylmorpholine‐N‐oxide (NMMO) and cuprammonium (denoted NMMO membranes and cuprammonium membranes, respectively). The concentration of cellulose in the casting solution investigated was 6–8 wt %. The permeation characteristics of both membrane series were compared in terms of the ultrafiltration rate (UFR) of pure water, the sieving coefficient (SC) of dextran, and the solute permeabilities of urea, creatinine, and vitamin B₁₂. The UFR and SC of the NMMO membranes were strongly affected by the cellulose concentration of the casting solution, and NMMO was a preferable solvent for the production of cellulose membranes with high performance; the cuprammonium solution gave low‐performance membranes. The pore structures of both types of membranes were estimated with the Hagen–Poiseuille law. The results showed that the NMMO membranes had larger pore radius and smaller pore numbers than the cuprammonium membranes. The differences in the membrane pore structures led to the differences in the performance between the two membrane series. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 333–339, 2003     

Modified cellulose fibers prepared by the N‐methylmorpholine‐N‐oxide (NMMO) process

Cellulose fibers with modified properties have been prepared from cellulose solutions in N‐methylmorpholine‐N‐oxide (NMMO). Poly(ethylene oxide) as a hydrophilic modifier and polyethylene as a hydrophobic modifier were added to the spinning solution. Based on microscope examination and measurements of such properties of fibers as porosity, moisture absorption, water retention, and tensile strength, structural changes as well as physical and mechanical properties of the resultant fibers depending on the amount of modifier added to the spinning solution were analyzed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 907–916, 2002     

Rheological aspects of fiber spinning from cellulose solutions in N‐methylmorpholine‐N‐oxide

Based on rheological experiments with a cellulose solution in N‐methylmorpholine‐N‐oxide (NMMO), it was found that the shearing stress generated in the flowing viscoelastic fluid decreases with an l/d ratio in a rheometer capillary. This reduces the elastic response and the outflow of the fluid becomes more uniform. At constant temperature, the elongational viscosity of the solidified stream of the cellulose solution in NMMO is reduced with increase of the deformation rate, which makes it possible to increase the fiber‐formation velocity within the air zone. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1860–1868, 2001     

Hemodialysis membrane prepared from cellulose/N‐methylmorpholine‐N‐oxide solution. I. Effect of membrane preparation conditions on its permeation characteristics

Flat hemodialysis membranes were prepared from cellulose/N‐methylmorpholine‐N‐oxide (NMMO) solutions (dope) with different cellulose concentrations (6–8 wt %) by using a phase‐inversion method. The coagulant used was NMMO aqueous solution, of which the NMMO concentration and its temperature were varied in the range of 0 to 50 wt % and 5 to 60°C, respectively. The effects of these preparation conditions on the permeation characteristics, the ultrafiltration rate (UFR) of pure water, and sieving coefficient (SC) of dextran, were investigated. The decrease in cellulose concentration of the dope and the increases in both temperature and NMMO concentration of the coagulant gave a membrane with high UFR. Concerning the SC, the increase of the cellulose concentration and the decreases in both temperature and NMMO concentration gave a good result. Consequently, the membrane having the preferable UFR and SC as a hemodialysis membrane was obtained when the 8 wt % cellulose dope was coagulated in water at 5°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2302–2307, 2002     

Atomic force microscopy of cellulose membranes prepared from the N‐methylmorpholine‐N‐oxide/water solvent system

Cellulose membranes were obtained by solutions of cellulose being cast into a mixture of N‐methylmorpholine‐N‐oxide (NMMO) and water under different processing conditions. Atomic force microscopy (AFM) was used to investigate the surface structures of the membranes. The AFM method provided information on both the size and shape of the pores on the surface, as well as the roughness of the skin, through a computerized analysis of AFM micrographs. The results obtained showed that the surface morphologies were intrinsically associated with the permeation properties. For the cellulose membranes, increasing the NMMO concentration and the temperature of the coagulation bath led to higher fluxes and lower bovine serum albumin rejection. These were always correlated with higher values of the roughness parameters and larger pore sizes of the membrane surfaces. When the cellulose concentration of the casting solution was 11 wt %, the membrane showed a nodular structure with interconnected cavity channels between the agglomerated nodules. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3389–3395, 2002     

Effects of a pretreatment with N‐methylmorpholine‐N‐oxide on the structures and properties of ramie

To improve the dyeing properties of ramie, the ecofriendly organic solvent N‐methylmorpholine‐N‐oxide (NMMO) was used to substitute sodium hydroxide as a ramie‐fiber swelling solvent. Through padding and baking pretreatment, ramie fabric was modified by an NMMO aqueous solution. Ultraviolet–visible spectrophotometry, Fourier transform infrared spectroscopy, X‐ray diffraction, and differential scanning calorimetry were used to investigate the effects of NMMO pretreatment on the structure of the ramie, whereas the color strength (K/S, where K is the light absorption coefficient and S is the scattering coefficient), adsorption isotherm, and dye uptake rate curve were measured to investigate the effects of NMMO pretreatment on the dyeing properties of the ramie. The results show that the ramie fiber experienced a limited and irreversible swelling because of the partial breakage of interhydrogen and intrahydrogen bonds of cellulose molecules in the amorphous area, but the crystal and chemical structure of the ramie fiber did not change obviously under the experimental conditions. The K/S value of the NMMO‐modified ramie fabrics dyed with reactive dyes increased by about 100%, and the dye uptake increased by 27.88% compared to that of the raw sample, whereas the standard affinity and diffusion coefficient value of the reactive dyes on the NMMO‐modified ramie fabric were higher than those of the raw ramie fabric. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

New solvent for polyrotaxane. III. Dissolution of a poly(ethylene glycol)/cyclodextrin polyrotaxane in a calcium thiocyanate aqueous solution or N‐methylmorpholine‐N‐oxide monohydrate

Calcium thiocyanate [Ca(SCN)₂] aqueous solutions above 40 wt % and N‐methylmorpholine N‐oxide (NMMO) monohydrate, which are known to dissolve cellulose, were found to be good solvents for a polyrotaxane comprising α‐cyclodextrin and poly(ethylene glycol). The polyrotaxane could be dissolved up to 12 and 10 wt % in a 40 wt % Ca(SCN)₂ aqueous solution and NMMO, respectively. These are the first instances of a neutral aqueous solution and a cyclic amine oxide, respectively, that readily dissolve the polyrotaxane. These new good solvents, as well as other solvents of the polyrotaxane, except for dimethyl sulfoxide, are identical to those of cellulose, indicating that the dissolution mechanism of the polyrotaxane is dominated by intra‐ and intermolecular hydrogen bonding of the molecule similar to that of cellulose dissolution. The concentrated polyrotaxane solution in a 40 wt % Ca(SCN)₂ aqueous solution showed apparent thixotropy and spontaneous gelation of the solution caused by a gradual increase in its viscosity. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Rheology of cellulosic N‐methylmorpholine oxide monohydrate solutions

Shear dynamic and elongational rheology of concentrated solutions of cellulose in N‐methylmorpholine oxide monohydrate (lyocell) were investigated at different temperatures and for two Hencky strains. Shear thinning and strain thinning behavior is characteristic for dynamic viscosity and effective elongational viscosity of lyocell solutions. Body forces, enthalpy, and entropy of orientation are high at low temperature and high deformation rates, showing a strong orientation effect. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1369–1377, 2000     

Preparation of well‐dispersed reduced graphene oxide and its mechanical reinforcement in polyvinyl alcohol fibre

The current work reports the preparation and characterization of polyvinyl alcohol (PVA) composite fibres reinforced with graphene reduced from graphene oxide (GO) by using oligomeric proanthocyanidin (OPC) as a reductant. After reduction, most of the oxygen‐containing groups were removed from the GO and reduced graphene oxide (rGO) was prepared. As a result of combined OPC as a dispersant, rGO could be well dispersed in a dimethyl sulfoxide/H₂O mixed solvent and in PVA matrix, and the PVA/rGO dispersion was wet spun followed by hot drawing to prepare continuous PVA/rGO composite fibres. The PVA/rGO composite fibres exhibited a significant enhancement of mechanical properties at low rGO loadings; in particular the tensile strength and Young's modulus of the 2.0 wt% rGO and PVA composite fibre increased to 244% and 294% respectively relative to neat PVA fibre. Moreover, the storage modulus (?10 °C) and T_g increased to 300% and 7.2 °C, respectively. © 2016 Society of Chemical Industry     

Effect of graphene oxide on the behavior of poly(amide‐6‐b‐ethylene oxide)/graphene oxide mixed‐matrix membranes in the permeation process

Polyether‐block‐amide (Pebax)/graphene oxide (GO) mixed‐matrix membranes (MMMs) were prepared with a solution casting method, and their gas‐separation performance and mechanical properties were investigated. Compared with the pristine Pebax membrane, the crystallinity of the Pebax/GO MMMs showed a little increase. The incorporation of GO induced an increase in the elastic modulus, whereas the strain at break and tensile strength decreased. The apparent activation energies (E_p) of CO₂, N₂, H₂, and CH₄ permeation through the Pebax/GO MMMs increased because of the greater difficulty of polymer chain rotation. The E_p value of CO₂ changed from 16.5 kJ/mol of the pristine Pebax to 23.7 kJ/mol of the Pebax/GO MMMs with 3.85 vol % GO. Because of the impermeable nature of GO, the gas permeabilities of the Pebax/GO MMMs decreased remarkably with increasing GO content, in particular for the larger gases. The CO₂ permeability of the Pebax/GO MMMs with 3.85 vol % GO decreased by about 70% of that of the pristine Pebax membrane. Rather than the Maxwell model, the permeation properties of the Pebax/GO MMMs could be described successfully with the Lape model, which considered the influence of the geometrical shape and arrangement pattern of GO on the gas transport. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42624.     

Preparation and characterization of epoxy nanocomposites containing surface‐modified graphene oxide

A three‐step grafting procedure has been used to graft the epoxy monomers (DER332) and the curing agents (diamino diphenyl methane (DDM), onto graphene oxide (GO) surface. The surface modification of GO has been performed by grafting of Jeffamine D‐2000, followed with subsequent grafting of DER332 and DDM, respectively. Fourier transform spectroscopy and thermogravimetric analysis indicate successful surface modification. The resulting modified GO, that is, (DED)‐GO, can be well dispersed in the epoxy monomers. The epoxy nanocomposites containing different GO contents can then be prepared through curing processes. The dispersion of GO in the nanocomposites is characterized by transmission electron microscopy. It is found that the tensile strength and elongation at break of epoxy nanocomposite with only 0.2 wt % DED‐GO are increased by 30 and 16% as compared with the neat epoxy resin, respectively. Dynamic mechanical analysis results show that 62% increase in storage modulus and 26°C enhancement in the glass transition temperature of the nanocomposite have been achieved with the incorporation of only 0.2 wt % of DED‐GO into the epoxy. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40236.     

Synthesis and flocculation properties of N‐oxide polymers

N‐oxide polymers possess strong zwitterionic character, high solubility in water, and high chelating properties with various cations. In this work, N‐oxide polymers were synthesized following various routes and their solution properties were determined. Molecular properties of the polymers (molecular weight, square root of the mean‐squared radius, and virial coefficients) were related to their chain expansion in solution by determining the intrinsic viscosity as a function of pH. Viscosity results were correlated with the flocculation ability of the polymers for suspending solids removal. These polymers exhibit dramatic conformation changes as the solution pH is varied, especially at low pH values. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2693–2700, 2002     

Ambipolar and multi‐electrochromic polyimides based on N,N‐di(4‐aminophenyl)‐N′,N′‐diphenyl‐4,4′‐oxydianiline

A series of novel aromatic polyimides were synthesized from N,N‐di(4‐aminophenyl)‐N′,N′‐diphenyl‐4,4′‐oxydianiline and aromatic tetracarboxylic dianhydrides through a conventional two‐step procedure. Most of the polyimides exhibited reasonable solubility in organic solvents and could afford robust films via solution casting. The polyimides exhibited high thermal stability, with glass transition temperatures in the range 227–273 °C and 10% weight‐loss temperatures in excess of 550 °C. All the polyimide films showed ambipolar redox and multi‐electrochromic behaviors. They exhibited two reversible oxidation redox couples at 0.94–0.98 and 1.09–1.12 V versus Ag/AgCl in acetonitrile solution. A coupling reaction between the radical cations of the pendent triphenylamine units occurred during the oxidative process forming a tetraphenylbenzidine structure which resulted in an additional redox state and color change. © 2014 Society of Chemical Industry     

Graphene oxide reinforced chitosan/polyvinylpyrrolidone polymer bio‐nanocomposites

Bio‐nanocomposite films based on chitosan/polyvinylpyrrolidone (CS/PVP) and graphene oxide (GO) were processed using the casting/evaporation technique. It has been found that the three components of bio‐nanocomposites can be easily mixed in controlled conditions enabling the formation of thick films with high quality, smooth surface and good flexibility. Structural and morphological characterizations showed that the GO sheets are well dispersed in the CS/PVP blend forming strong interfacial interactions that provide an enhanced load transfer between polymer chains and GO sheets thus improving their properties. It has been found that the water resistance of the CS/PVP blend is improved, and the hydrolytic degradation is limited by addition of 0.75 and 2 wt % GO. The modulus, strength, elongation and toughness of the bio‐nanocomposites are together increased. Herein, the steps to form new bio‐nanocomposite films have been described, taking the advantage of the combination of CS, PVP and GO to design the aforementioned bio‐nanocomposite films, which allow to have extraordinary properties that would have promising applications as eventual packaging materials. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41042.     

Hemodialysis membrane prepared from cellulose/N‐methylmorpholine‐N‐oxide solution. III. The relationship between the drying condition of the membrane and its permeation behavior

The effects of drying condition on the performance (ultrafiltration rate, diffusive solute permeability, and sieving) of hemodialysis membranes prepared from cellulose/N‐methylmorpholine‐N‐oxide (NMMO) solution (NMMO membrane) and cellulose/cuprammonium solution (cuprammonium membrane; the referential membrane) were studied. The drying condition investigated was the glycerin concentration of the solution, which was used to substitute glycerin for the water in the membrane before the membrane was dried. A lower glycerin concentration in the solution brought about a lower reswelling degree (water content) in the dried membrane in pure water, which resulted in a drop in the performance of the as‐cast membrane. The NMMO membrane had a high water content and a high membrane performance compared with the cuprammonium membrane when both the membranes were treated under the same drying condition. The differences in the performance between both membrane series is discussed on the basis of the results of the observation of the membrane morphology by scanning electron microscopy, the observation of the crystallinity of the membranes by wide‐angle X‐ray diffraction, and the estimation of the pore structure of the membranes. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1671–1681, 2003