Non-Isothermal Crystallization of High-Impact Polystyrene/Poly(Phenylene Sulfide) Blends

The morphology of isothermally crystallized poly(phenylene sulfide) (PPS) and a blend combining it with high-impact polystyrene (HIPS) were observed through a polarized optical microscope equipped with a CSS450 hot-stage. The crystalline superstructure of PPS is mainly spherulite, and it was found that the presence of HIPS has little influence on the morphology of PPS, but decreases the nucleation rate of PPS. The effect of HIPS on the non-isothermal crystallization of PPS was investigated by differential scanning calorimetry (DSC). The maximum and onset crystallization temperatures for the HIPS/PPS blend were about 10°C lower than those of neat PPS, which indicates that the crystallization of PPS was retarded by HIPS. The Ozawa model was used to analyze the non-isothermal crystallization kinetics of PPS and its blends. The Avrami exponent values of neat PPS were higher than those of its blend, which shows that the presence of HIPS changed both the nucleation rate and the crystallization rate of PPS.     

Dependence of the Avrami Exponent on Supercooling During Nonisothermal Crystallization of Poly(phenylene sulfide)

The nonisothermal crystallization behavior of poly(phenylene sulfide) (PPS) was studied by means of differential scanning calorimetry (DSC) at various cooling rates. The nonisothermal crystallization data were analyzed by the Ozawa theory. The Avrami exponent n was determined at several constant cooling rates. A notable variable trend of the Avrami exponent with the temperature was found. Within 215–238°C and 243–255°C, the Avrami exponent of PPS increases markedly with the increase of temperature, respectively, while within narrow temperature range from 238°C to 243°C, a sharp decrease of the Avrami exponent can be seen. It has been suggested that the nuclei formation and the geometry of spherulite growth in the nonisothermal crystallization of PPS are strongly affected by the temperature and correlated with the Regime Transition (the regime II→III transition for PPS).     

Miscibility and crystallization behavior of poly(ether ether ketone ketone)/poly(ether imide) blends

The miscibility and crystallization behavior of poly(ether ether ketone ketone) (PEEKK)/poly(ether imide) (PEI) blends prepared by melt‐mixing were investigated by differential scanning calorimetry. The blends showed a single glass transition temperature, which increased with increasing PEI content, indicating that PEEKK and PEI are completely miscible in the amorphous phase over the studied composition range (weight ratio: 90/10–60/40). The cold crystallization of PEEKK blended with PEI was retarded by the presence of PEI, as is apparent from the increase of the cold crystallization temperature and decrease of the normalized crystallinity for the samples anealed at 300°C with increasing PEI content. Although the depression of the apparent melting temperature of PEEKK blended with PEI was observed, there was no evidence of depression in the equilibrium melting temperature. The analysis of the isothermal crystallization at 313–321°C from the melt of PEEKK/PEI (100/0, 90/10, and 80/20) blends suggested that the retardation of crystallization of PEEKK is caused by the increase of the crystal surface free energy in addition to the decrease of the mobility by blending PEI with a high glass transition temperature. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 769–775, 2001     

Miscibility,Mechanical and Thermal Properties of Melt-Mixed Poly(trimethylene terephthalate)/Polypropylene Blends

This study examined the miscibility, mechanical and thermal properties of melt-mixed blends of PTT(poly(trimethylene terephthalate)) with PP(isotatic polypropylene). DMA and SEM results indicated that the PTT/PP blends are immiscible. Revealed from TGA analyses, the blends with a higher PP content showed a higher degradation temperature. A complex melting behavior was observed for the blends. The isothermal crystallization kinetics of the blends was analyzed from 200°C to 210°C using the Avrami equation. The WAXD results showed that the crystal structure of PTT remained unchanged in the blends. Nevertheless, the PP rich blends possessed lower tensile strength and higher elongation at break.     

Poly(p-phenylene sulfide)/liquid crystalline polymer blends. II. Crystallization kinetics

The crystallization kinetics of blends made of poly(p-phenylene sulfide) (PPS) with a liquid crystalline polymer (LCP) was studied. The blends were found to be immiscible by dynamic mechanical thermal analysis (DMTA). Results of non-isothermal and isothermal crystallization experiments made by differential scanning calorimetry (DSC) showed that both components had their crystallization temperatures increased; also the LCP melting temperature was found to increase in the blends. It was concluded that the addition of LCP to the PPS increased the PPS overall crystallization rate due to heterogeneous nucleation. The fold interfacial free energy, σ_e of the PPS in the blends was observed not to vary with composition. © 1996 John Wiley & Sons, Inc.     

Investigation on the crystallization behavior of poly(ether ether ketone)/poly(phenylene sulfide) blends

The morphology of nonisothermally crystallized poly(phenylene sulfide) (PPS) and its blend with poly (ether ether ketone) (PEEK) have been observed by polarized optical microscope (POM) equipped with a hot stage. The nonisothermal crystallization behavior of PPS and PEEK/PPS blend has also been investigated by differential scanning calorimetry (DSC). The maximum crystallization temperature for PEEK/PPS blend is about 15°C higher than that of neat PPS, and the crystallization rate, characterized by half crystallization time, of the PEEK/PPS blend is also higher than that of the neat PPS. These results indicate that the PEEK acts as an effective nucleation agent and greatly accelerates the crystallization rate of PPS. The Ozawa model was used to analyze the nonisothermal crystallization kinetics of PPS and its blends. The Avrami exponent values of neat PPS are higher than that of its blend, which shows that the presence of PEEK changed the nucleation type of PPS from homogeneous nucleation to heterogeneous nucleation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal studies of blends of poly(phenylene sulfide) (PPS) with poly(phenylene sulfide sulfone) (PPSS) and with poly(phenylene sulfide ether) (PPSE)

The miscibilities of poly(phenylene) sulfide/poly(phenylene sulfide sulfone) (PPS/PPSS) and poly(phenylene) sulfide/poly(phenylene sulfide ether) (PPS/PPSE) blends were invesigated in terms of shifts of glass transition temperatures T_g of pure PPS, PPSS, a dn PPSE. The crystallization kinetics of PPS/PPSS blends was also studied as a function of molar composition. The PPS/PPSS and PPS/PPSE blends are respectively partially and fully miscible. PPSE shows a plasticizing effect on PPS as does PPS on PPSS, which necessarily improves te processibility in the respective systems. We can control T_g and melting temperature T_m of PPS by varying amounts of PPSE in blends. The melt crystallization temperature T_mc of PPS/PPSE blends was higher than that of the PPSE homopolymer. Therefore, these blends require shorter cycle times in processing than pure PPSE. The overall rate of crystallization for PPS/PPSS blends follows the Avrami equation with an exponent ?2. The maximal rate of crystallization for PPS/PPSS blends occurs at a temperatre higher by 10°C than that for PPS, while the crystallization half time t_1/2 is 4 times shorter. In the cold crystallization range, crystal growth rates increase and Avrami exponents decrease significantly as the temperature increases.     

Effects of Carbon Fillers on Crystallization Properties and Thermal Conductivity of Poly(phenylene sulfide)

Differential scanning calorimetry and polarized optical microscopy methods were used to investigate the crystallization behavior and isothermal crystallization kinetics of poly(phenylene sulfide) (PPS)/carbon nanotube (CNT) and PPS/CNT/carbon fiber (CF) composites. In this article, the influences of CNT and CF on PPS crystallization behavior are explained. The thermal conductivity properties of composites were studied using the laser flash method. The results show that CNT increased crystallization temperature and rate and thermal conductivity greatly improved at 8 wt.% CNT content. In addition, the crystallization and thermal performance of PPS are significantly improved via synergistic effects of CNT and CF in the composites.     

PPS/TLCP共混体系非等温结晶行为及性能研究

研究了聚苯硫醚（PPS）与全芳及半芳族热致性液晶（TLCP）共混物的结晶和熔融行为；通过差示扫描量热仪（DSC）和偏光显微镜（PLM）分析了PPS的结晶过程和晶体微观结构，并研究了材料力学性能。研究表明，加入少量全芳或半芳族TLCP，可显著提高PPS最大结晶温度和结晶速率，全芳族TLCP起异向成核作用，而半芳族TLCP促进晶体增长；加入质量分数为2％的全芳族TLCP，可同时提高PPS的拉伸和冲击强度。     

Effect of high-performance polymers on crystallization and multiple melting behavior of poly(phenylene sulfide)

The crystallization and multiple melting behavior of poly(phenylene sulfide) (PPS) and its blends with amorphous thermoplastic bisphenol A polysulfone (PSF) and phenolphthalein poly(ether ketone) (PEK-C), crystalline thermoplastic poly(ether ether ketone) (PEEK), and thermosetting bismaleimide (BMI) resin were investigated by a differential scanning calorimeter (DSC). The addition of PSF and PEK-C was found to have no influence on the crystallization temperature (T_c) and heat of crystallization (ΔH_c) of PPS. A significant increase in the value of T_c and the intensity of the T_c peak of PPS was observed and the crystallization of PPS can be accelerated in the presence of the PEEK component. An increase in the T_c of PPS can also be accelerated in the BMI/PPS blend, but was no more significant than that in the PEEK/PPS blend. The T_c of PPS in the PEEK/PPS blends is dependent on the maximum temperature of the heating scans and can be divided into three temperature regions. The addition of a second component has no influence on the formation of a multiple melting peak. The double melting peaks can also be observed when PPS and its blends are crystallized dynamically from the molten state. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 637–644, 1998     

Unique Homo-Crystallization and Melting Behavior of Poly(L-lactic acid): Influence of Stereocomplex with Varied Structure

Homo-crystallization and melting behavior of poly(L-lactic acid) (PLLA) with poly(D-lactic acid) (PDLA) (≤10 wt.%) was studied. The different thermal history had been applied to exert structural variation on stereocomplex (SC). The PLLA/PDLA blend showed different crystallization and melting behavior when cooled from 250°C or 200°C. Double melting peaks were observed after the blend was cooled from 250°C. SC annealing at different temperatures exhibited significant effect for melt-crystallization of PLLA. Influence of initial melting condition before cooling was also investigated. The cold crystallization of amorphous blend initially was studied and some novel results had been observed.     

Crystallization and melting behavior of poly(p‐phenylene sulfide) in blends with poly(ether sulfone)

Crystallization and melting behaviors of poly(p‐phenylene sulfide) (PPS) in blends with poly(ether sulfone) (PES) prepared by melt‐mixing were investigated by differential scanning calorimetry (DSC). The blends showed two glass transition temperatures corresponding to PPS‐ and PES‐rich phases, which increased with increasing PES content, indicating that PPS and PES have some compatibility. The cold crystallization temperature of the blended PPS was a little higher than that of pure PPS. Also, the heats of crystallization and melting of the blended PPS decreased with increasing PES content, indicating that the degree of crystallinity decreased with an increase of PES content. The isothermal crystallization studies revealed that the crystallization of PPS is accelerated by blending PPS with 10 wt % PES and further addition results in the retardation. The Avrami exponent n was about 4 independent on blend composition. The activation energy of crystallization increased by blending with PES. The equilibrium melting point decreased linearly with increasing PES content. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1686–1692, 1999     

Miscibility and transesterification in ternary blends of poly(ethylene naphthalate)/poly(pentamethylene terephthalate)/poly(ether imide)

Miscibility and morphology of poly(ethylene 2,6‐naphthalate)/poly(pentamethylene terephthalate)/poly(ether imide) (PEN/PPT/PEI) blends were studied by differential scanning calorimetry (DSC), optical microscopy (OM), proton nuclear magnetic resonance imaging (¹H‐NMR), and wide‐angle X‐ray diffraction (WAXD). OM and DSC results from ternary blends revealed the immiscibility of PEN/PPT/PEI blends, but ternary blends of all compositions were phase‐homogeneous following heat treatment at 300°C for over 60 min. Annealing samples at 300°C yielded an amorphous blend with a clear and single T_g at the final state. Experimental data from ¹H‐NMR revealed that PEN/PPT copolymers (ENPT) were formed by the so‐called transesterification. The effect of transesterification on glass transition and crystallization was discussed in detail. The sequence structures of the copolyester were identified by triad analysis, which showed that the mean sequence lengths became shorter and the randomness increased with heating time. The results reveal that a random copolymer improved the miscibility of the ternary blends, in which, the length of the homo segments in the polymer chain decreased and the crystal formation was disturbed because of the irregularity of the structure, as the exchange reaction proceeded. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3840–3849, 2006     

Biodegradable polymer blends of poly(3-hydroxybutyrate) and poly(DL-lactide)-co-poly(ethylene glycol)

The melting and crystallization behavior and phase morphology of poly(3-hydroxybutyrate) (PHB) and poly(DL-lactide)-co-poly(ethylene glycol) (PELA) blends were studied by DSC, SEM, and polarizing optical microscopy. The melting temperatures of PHB in the blends showed a slight shift, and the melting enthalpy of the blends decreased linearly with the increase of PELA content. The glass transition temperatures of PHB/PELA (60/40), (40/60), and (20/80) blends were found at about 30°C, close to that of the pure PELA component, during DSC heating runs for the original samples and samples after cooling from the melt at a rate of 20°C/min. After a DSC cooling run at a rate of 100°C/min, the blends showed glass transitions in the range of 10–30°C. Uniform distribution of two phases in the blends was observed by SEM. The crystallization of PHB in the blends from both the melt and the glassy state was affected by the PELA component. When crystallized from the melt during the DSC nonisothermal crystallization run at a rate of 20°C/min, the temperatures of crystallization decreased with the increase of PELA content. Compared with pure PHB, the cold crystallization peaks of PHB in the blends shifted to higher temperatures. Well-defined spherulites of PHB were found in both pure PHB and the blends with PHB content of 80 or 60%. The growth of spherulites of PHB in the blends was affected significantly by 60% PELA content. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 1849–1856, 1997     

Microstructure and crystallization of melt‐mixed poly(ethylene terephthalate)/poly(ethylene isophthalate) blends

Physical blends of poly(ethylene terephthalate) (PET) and poly(ethylene isophthalate) (PEI), abbreviated PET/PEI (80/20) blends, and of PET and a random poly(ethylene terephthalate‐co‐isophthalate) copolymer containing 40% ethylene isophthalate (PET₆₀I₄₀), abbreviated PET/PET₆₀I₄₀ (50/50) blends, were melt‐mixed at 270°C for different reactive blending times to give a series of copolymers containing 20 mol % of ethylene isophthalic units with different degrees of randomness. ¹³C‐NMR spectroscopy precisely determined the microstructure of the blends. The thermal and mechanical properties of the blends were evaluated by DSC and tensile assays, and the obtained results were compared with those obtained for PET and a statistically random PETI copolymer with the same composition. The microstructure of the blends gradually changed from a physical blend into a block copolymer, and finally into a random copolymer with the advance of transreaction time. The melting temperature and enthalpy of the blends decreased with the progress of melt‐mixing. Isothermal crystallization studies carried out on molten samples revealed the same trend for the crystallization rate. The effect of reaction time on crystallizability was more pronounced in the case of the PET/PET₆₀I₄₀ (50/50) blends. The Young's modulus of the melt‐mixed blends was comparable to that of PET, whereas the maximum tensile stress decreased with respect to that of PET. All blend samples showed a noticeable brittleness. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3076–3086, 2003     

Crystallization kinetics of poly(trimethylene terephthalate)/poly(ether imide) blends

The crystallization kinetics of a melt‐miscible blend, consisting of poly(trimethylene terephthalate) (PTT) and poly(ether imide) (PEI) prepared by solution precipitation, has been investigated by means of optical polarized microscopy and differential scanning calorimeter. It was found that both the PTT spherulitic growth rate (G) and overall crystallization rate constant (k_n) were depressed, with increasing PEI composition or crystallization temperature (T_c). The kinetic retardation was attributed to the decrease in PTT molecular mobility, and the dilution of PTT concentration due to the addition of PEI, which has a higher glass transition temperature (T_g). According to the Lauritzen–Hoffman theory of secondary nucleation, the crystallization of PTT in blends was similar to that of neat PTT as regime III, n = 4 and regime II, n = 2 growth processes, while the transition point of regime III to II has been shifted from 194°C for neat PTT to 190°C for blends. POLYM. ENG. SCI. 46:89–96, 2006. © 2005 Society of Plastics Engineers     

Reactively formed ENPT copolymers as compatibilizers in ternary blends of poly(ethylene naphthalate)/poly(pentamethylene terephthalate)/poly(ether imide)

The compatibility of ternary blends of poly(ethylene naphthalate)/poly(pentamethylene terephthalate)/poly(ether imide) (PEN/PPT/PEI) was studied by examining the transesterification of PEN and PPT. ENPT copolymers were formed in situ as compatibilizers between PPT and PEI components in ternary blends. Differential scanning calorimetric (DSC) results for ternary blends showed the immiscibility of PEN/PPT/PEI, but ternary blends of all compositions were phase‐homogeneous after heat treatment at 300°C for more than 60 min. Annealing samples at 300°C yielded amorphous blends with a clear, single glass transition temperature (T_g), as the final state. Additionally, ENPT copolymer improved the compatibility of ENPT/PPT/PEI blends, yielding a homogeneous phase in the ENPT‐rich compositions. The morphology of the ENPT/PPT/PEI blends was altered from heterogeneous to homogeneous by controlling the concentration of PPT in the ENPT copolymers as well as the concentration of the ENPT copolymers. Moreover, a homogeneous phase with a clear T_g was observed when the concentration of PPT in the ENPT copolymer fell to 70 wt% in the ENPT/PEI = 50/50 blends. Experimental results indicate how the concentration of PPT in the ENPT copolymer affects miscibility in the ENPT/PEI blends. POLYM. ENG. SCI. 46:337–343, 2006. © 2006 Society of Plastics Engineers     

Miscibility and crystallization behavior of biodegradable blends of two aliphatic polyesters. Poly(3-hydroxybutyrate-co-hydroxyvalerate) and poly(ε-caprolactone)

Biodegradable polymer blends of poly(3-hydroxybutyrate-co-hydroxyvalerate) (PHBV) and poly(ε-caprolactone) (PCL) blends were prepared with the ratio of PHBV/PCL ranging from 80/20-20/80 by co-dissolving the two polyesters in chloroform and casting the mixture. Differential scanning calorimetry (DSC) and optical microscopy (OM) were used to investigate the miscibility and crystallization of PHBV/PCL blends. Experimental results indicated that PHBV showed no miscibility with PCL for PHBV/PCL blends as evidenced by the existence of unchanged composition independent glass transition temperature and the biphasic melt. Crystallization of PHBV and PCL was studied with DSC and analyzed by the Avrami equation by using two-step crystallization in the PHBV/PCL blends. The crystallization rate of PHBV at 70 °C decreased with the increase of PCL in the blends, while the crystallization mechanism did not change. In the case of the isothermal crystallization of PCL at 42 °C, the crystallization rate increased with the addition of PHBV, and the crystallization mechanism changed, too, indicating that the crystallization of PHBV at 70 °C had an apparent influence on the crystallization of PCL at 42 °C.     

聚甲基乙烯基硅氧烷增韧聚苯硫醚的力学性能研究

通过熔融共混制备了聚苯硫醚/无苯基聚甲基乙烯基硅氧烷(PPS/NPMVS)共混物及聚苯硫醚/单苯基聚甲基乙烯基硅氧烷(PPS/SPMVS)共混物,并对该共混物体系的微观形貌及力学性能进行了分析表征。结果表明,弹性体在共混物中均匀分散,弹性体的加入对PPS基体起到明显的增韧效果;当弹性体的含量为3 %（质量分数,下同）时,2种共混材料的增韧性能最佳,PPS/NPMVS共混材料的断裂伸长率相对于PPS基体提高了3.9倍,PPS/SPMVS共混材料的断裂伸长率相对于PPS基体提高了2.4倍;当NPMVS含量为10 %时,PPS/NPMVS共混材料的冲击强度相对于PPS基体提高了1.8倍,当SPMVS含量为3 %时,PPS/SPMVS共混材料的冲击强度相对于PPS基体提高了1.4倍。     

Thermal and crystallization behavior of engineering polyblends. II. Unfilled polyphenylene sulfide with poly(ethylene terephthalate)

The melting and crystallization behavior of blends of poly(phenylene sulfide) (PPS) with poly(ethylene terephthalate) (PET) has been investigated. The component polymers in the blend exhibited separate crystallization peaks and overlapping melting peaks. The nonisothermal DSC scans indicated that the crystallization parameters for PET become modified to a greater extent than do those for PPS in the blends. The PET crystallization peak became narrower with a higher heat of crystallization, suggesting a faster rate of crystallization as a result of blending with PPS. The isothermal crystallization studies revealed that the nucleation of PPS is facilitated by the presence of PET. This contention has been substantiated by polarized light microscopic observations. The spherulites of PPS were found to be smaller in the blends as compared to those in neat PPS. This enhancement in the nucleation of PPS has been attributed to the possibilities of chemical interactions between the component polymers. On the other hand, the increase in the rate of crystallization of PET has been attributed to the heterogeneous nucleation provided by the alreadycrystallized PPS. The melt crystallized blends exhibited slightly higher heats of fusion compared to the values computed from the rule of proportional additivity. © 1994 John Wiley & Sons, Inc.