Carrier transport related analysis of high-power AlGaN/GaN HEMTstructures

Shubnikov-de Haas (SdH) oscillation and Hall measurement results were compared with HEMT DC and RF characteristics for two different MOCVD grown AlGaN-GaN HEMT structures on semiinsulating 4H-SiC substrates. A HEMT with a 40-nm, highly doped AlGaN cap layer exhibited an electron mobility of 1500 cm²/V/s and a sheet concentration of 9×10¹² cm at 300 K (7900 cm²/V/s and 8×10¹² cm^-2 at 80 K), but showed a high threshold voltage and high DC output conductance. A 27-nm AlGaN cap with a thinner, lightly doped donor layer yielded similar Hall values, but lower threshold voltage and output conductance and demonstrated a high CW power density of 6.9 W/mm at 10 GHz. The 2DEG of this improved structure had a sheet concentration of n_SdH=7.8×10¹² cm^-2 and a high quantum scattering lifetime of τ_q=1.5×10^-13 s at 4.2 K compared to n_SdH=8.24×10¹² cm^-2 and τ_q=1.72×10^-13 s for the thick AlGaN cap layer structure, Despite the excellent characteristics of the films, the SdH oscillations still indicate a slight parallel conduction and a weak localization of electrons. These results indicate that good channel quality and high sheet carrier density are not the only HEMT attributes required for good transistor performance     

Fabrication and characterization of high-performance InP/InGaAsdouble-heterojunction bipolar transistors

This paper is on high-performance InP/InGaAs double-heterojunction bipolar transistors (DHBT's) utilizing compositionally step-graded InGaAsP layers between the InGaAs base and InP collector to suppress the current blocking effect. These DHBT's exhibit current gains of 200 and excellent breakdown behavior. Moreover, the DHBT's permit collector current density levels J_C up to 3×10⁵ A/cm ² at V_CE=1.5 V. A current gain cutoff frequency of 155 GHz and a maximum oscillation frequency of 90 GHz have been successfully obtained at J_C=1.6×10⁵ A/cm². We have also investigated electron transport properties in the InP collector using a set of DHBT's with different injection energies into the InP collector. By increasing the injection energies, electron velocity is found to decrease from 3.5×10⁷ cm/s to 1.6×10⁷ cm/s, due to increased population of upper valleys. This result clearly demonstrates the significant role of nonequilibrium Γ-valley transport in determining the high-speed performance of InP/InGaAs DHBT's     

Short channel AlGaN/GaN MODFET's with 50-GHz fT and1.7-W/mm output-power at 10 GHz

A thin barrier-donor layer of 200 Å was used to increase the active input capacitance and improve the extrinsic current-gain cutoff frequency (f_t) of short-gate-length AlGaN/GaN MODFETs. 0.2-μm gate-length devices fabricated on such an epi-structure with sheet carrier density of ~8×10¹² cm^-2 and mobility of 1200 cm²/Vs showed a record f_t of 50 GHz for GaN based FETs. High channel saturation current and transconductance of 800 mA/mm and 240 mS/mm respectively were also achieved along with breakdown voltages of 80 V per μm gate-drain spacing. These excellent characteristics translated into a CW output power density of 1.7 W/mm at 10 GHz, exceeding previous record for a solid-state HEMT     

p-channel modulation-doped field-effect transistors based on AlSb0.9As0.1/GaSb

Operation of the first AlSbAs/GaSb p-channel modulation-doped field-effect transistor (MODFET) is reported. Devices with 1-μm gate length exhibit transconductance of 30 and 110 mS/mm at room temperature and 80 K, with respective maximum drain current densities of 25 and 80 mA/mm. The low field Hall mobility and sheet carrier density of this modulation doped structure were 260 cm²/V-s and 1.8×10 ¹² cm^-2 at room temperature and 1700 cm²/V-s and 1.4×10¹² cm^-2 at 77 K. Calculations based on these results indicate that room-temperature transconductances of 200 mS/mm or greater could be achieved. This device can be integrated with an InAs n-channel HFET for complementary circuit applications     

High-performance, 0.1 μm InAlAs/InGaAs high electron mobilitytransistors on GaAs

This letter describes the material characterization and device test of InAlAs/InGaAs high electron mobility transistors (HEMTs) grown on GaAs substrates with indium compositions and performance comparable to InP-based devices. This technology demonstrates the potential for lowered production cost of very high performance devices. The transistors were fabricated from material with room temperature channel electron mobilities and carrier concentrations of μ=10000 cm² /Vs, n=3.2×10¹² cm^-2 (In=53%) and μ=11800 cm²/Vs, n=2.8×10¹² cm^-2 (In=60%). A series of In=53%, 0.1×100 μm² and 0.1×50 μm² devices demonstrated extrinsic transconductance values greater than 1 S/mm with the best device reaching 1.074 S/mm. High-frequency testing of 0.1×50 μm² discrete HEMT's up to 40 GHz and fitting of a small signal equivalent circuit yielded an intrinsic transconductance (g_m,i) of 1.67 S/mm, with unity current gain frequency (f_T) of 150 GHz and a maximum frequency of oscillation (f_max) of 330 GHz. Transistors with In=60% exhibited an extrinsic g_m of 1.7 S/mm, which is the highest reported value for a GaAs based device     

Power performance of InP-based single and double heterojunctionbipolar transistors

The microwave and power performance of fabricated InP-based single and double heterojunction bipolar transistors (HBTs) is presented. The single heterojunction bipolar transistors (SHBTs), which had a 5000 Å InGaAs collector, had BV_CEO of 7.2 V and J_Cmax of 2×10⁵ A/cm². The resulting HBTs with 2×10 μm² emitters produced up to 1.1 mW/μm2 at 8 GHz with efficiencies over 30%. Double heterojunction bipolar transistors (DHBTs) with a 3000-Å InP collector had a BV_CEO of 9 V and J_{c max} of 1.1×10⁵ A/cm², resulting in power densities up to 1.9 mW/μm² at 8 GHz and a peak efficiency of 46%. Similar DHBTs with a 6000 Å InP collector had a higher BV_CEO of 18 V, but the J _{c max} decreased to 0.4×10⁵ A/cm² due to current blocking at the base-collector junction. Although the 6000 Å InP collector provided higher f_max and gain than the 3000 Å collector, the lower J_{c max} reduced its maximum power density below that of the SHBT wafer. The impact on power performance of various device characteristics, such as knee voltage, breakdown voltage, and maximum current density, are analyzed and discussed     

High-speed InGaP/GaAs transistors with a sidewall base contactstructure

We have fabricated InGaP/GaAs double heterojunction bipolar transistors with a sidewall base contact structure. These transistors operate in both emitter-up and emitter-down modes. Symmetric characteristics of the cutoff frequency f_T=68 GHz and the maximum oscillation frequency f_max=31 GHz were obtained at a base-collector bias V_BC of 0 V. For emitter-down operation, f _T was found to reach a maximum of 78 GHz when the base-collector junction was forward biased at 0.9 V. The product of f _T for emitter-down operation and f_T for emitter-up operation was 5.3×10³ GHz², which is about six times that of previously reported SiGe heterojunction bipolar transistors     

Si/a-Si:H heterojunction microwave bipolar transistors with cut-offfrequencies ft above 5 GHz

The fabrication of a silicon heterojunction microwave bipolar transistor with an n⁺ a-Si:H emitter is discussed, and experimental results are given. The device provides a base sheet resistance of 2 kΩ/□ a base width 0.1 μm, a maximum current gain of 21 (V_CE=6 V, I_c=15 mA), and an emitter Gummel number G _E of about 1.4×10¹⁴ Scm^-4. From the measured S parameters, a cutoff frequency f_t of 5.5 GHz and maximum oscillating frequency f_max of 7.5 GHz at V_CE=10 V, I_c=10 mA are obtained     

Dynamic characterisation of Si/SiGe power HBTs

Si/SiGe power heterojunction bipolar transistors (HBTs) grown by MBE were dynamically characterised in the common-base configuration. At an emitter current density of 1.1×10⁵ A/cm², a maximum frequency of oscillation of 49 GHz was observed. At 10 GHz a maximum unilateral gain of 14 dB is available, and a CW output power of 1.3 W/mm for a device with 10 parallel emitter-fingers of 1×10 μm² each was predicted, from CW measurements     

0.2-μm gate-length atomic-planar doped pseudomorphic Al0.3Ga0.7As/In0.25Ga0.75As MODFETswith fT over 120 GHz

The authors report the DC and RF performance of nominally 0.2-μm-gate length atomic-planar doped pseudomorphic Al_0.3Ga_0.7As/In_0.25Ga_0.75As modulation-doped field-effect transistors (MODFETs) with f_T over 120 GHz. The devices exhibit a maximum two-dimensional electron gas (2 DEG) sheet density of 2.4×10¹² cm^-2, peak transconductance g _m of 530-570 mS/mm. maximum current density of 500-550 mA/mm, and peak current-gain cutoff frequency f_T of 110-122 GHz. These results are claimed to be among the best ever reported for pseudomorphic AlGaAs/InGaAs MODFETs and are attributed to the high 2 DEG sheet density, rather than an enhanced saturation velocity, in the In_0.25Ga_0.75As channel     

Bi1.5Zn1.0 Nb1.5O7栅绝缘层的SiO2修饰对ZnO-TFTs性能的影响

具有高介电常数的栅绝缘层材料存在某种极化及耦合作用,使得ZnO-TFTs具有高的界面费米能级钉扎效应、大的电容耦合效应和低的载流子迁移率.为了解决这些问题,本文提出了一种使用SiO₂修饰的Bi_1.5Zn_1.0Nb_1.5O₇作为栅绝缘层的ZnO-TFTs结构,分析了SiO₂修饰对栅绝缘层和ZnO-TFTs性能的影响.结果表明,使用SiO₂修饰后,栅绝缘层和ZnO-TFTs的性能得到显著提高,使得ZnO-TFTs在下一代显示领域中具有非常广泛的应用前景.栅绝缘层的漏电流密度从4.5×10^-5A/cm²降低到7.7×10^-7A/cm²,粗糙度从4.52nm降低到3.74nm,ZnO-TFTs的亚阈值摆幅从10V/dec降低到2.81V/dec,界面态密度从8×10¹³cm^-2降低到9×10¹²cm^-2,迁移率从0.001cm²/（V·s）升高到0.159cm²/（V·s）.     

Design and fabrication of double modulation dopedInAlAs/lnGaAs/InAs heterojunction FETs for high-speed andmillimeter-wave applications

We report the design, fabrication, and characterization of InP-based double-sided-doped (DSD) MODFETs with InAs-layer-inserted channels. Devices based on optimized structures show a significant improvement in the effective saturation velocity, from 2.4×10⁷ cm/s for lattice-matched MODFETs to 3.1×10⁷ cm/s for InAs MODFETs. This leads to a maximum extrinsic transconductance of 1.95 S/mm and excellent high-speed performance of f_T=265 GHz for 0.13-μm T-gates. A f_max higher than 300 GHz can be achieved by fabricating a wide lateral recess groove, which simultaneously results in an improved breakdown voltage of 6.7 V. The excellent RF performance is primarily due to the reduction of Coulomb scattering from donor layers, especially under the channel, and to the reduction of scattering caused by the interface roughness. This improvement is achieved by inserting a 4-nm InAs layer, which better confines the two-dimensional electron gas (2DEG) at the center of the channel of MODFET's     

Fully-planar AlGaAs/GaAs HBT's achieved by selective CBE regrowth

This paper describes a novel fully planar AlGaAs/GaAs heterojunction bipolar transistor (HBT) technology using selective chemical beam epitaxy (CBE). Planarization is achieved by a selective regrowth of the base and collector contact layers. This process allows the simultaneous metallization of the emitter, base and collector on top of the device. For the devices with an emitter-base junction area of 2×6 μm² and a base-collector junction area of 14×6 μm², a current gain cut off frequency of 50 GHz and a maximum oscillation frequency of 30 GHz are achieved. The common emitter current gain h_FE is 25 for a collector current density J_c of 2×10⁴ A/cm²     

Electron transport in 0.15-μm gate In0.52Al0.48As/In0.53Ga0.47As HEMT

Magneto-transport and cyclotron resonance measurements were made to determine directly the density, mobility, and the effective mass of the charge carriers in a high-performance 0.15-μm gate In_0.52 Al_0.48As/In_0.53Ga_0.47As high-electron-mobility transistor (HEMT) at low temperatures. At the gate voltage V_G=0 V, the carrier density n _g under the gate is 9×10¹¹ cm^-2, while outside of the gate region n_g=2.1×10¹² cm^-2. The mobility under the gate at 4.2 K is as low as 400 cm²/V-s when V_G<0.1 V and rapidly approaches 11000 cm²/V-s when V_G>0.1 V. The existence of this high mobility threshold is crucial to the operation of the device and sets its high-performance region in V_G>0.1 V     

High quality SiO2/Si interfaces of poly-crystallinesilicon thin film transistors by annealing in wet atmosphere

A new post-metallization annealing technique was developed to improve the quality of metal-oxide-semiconductor (MOS) devices using SiO ₂ films formed by a parallel-plate remote plasma chemical vapor deposition as gate insulators. The quality of the interface between SiO₂ and crystalline Si was investigated by capacitance-voltage (C-V) measurements. An H₂O vapor annealing at 270°C for 30 min efficiently decreased the interface trap density to 2.0×10¹⁰ cm^-2 eV^-1, and the effective oxide charge density from 1×10 ¹² to 5×10⁹ cm^-2. This annealing process was also applied to the fabrication of Al-gate polycrystalline silicon thin film transistors (poly-Si TFT's) at 270°C. In p-channel poly-Si TFT's, the carrier mobility increased from 60-400 cm² V^-1 s^-1 and the threshold voltage decreased from -5.5 to -1.7 V     

Characterization of double pulse-doped channel GaAs MESFETs

The fabrication and characterization of a double pulse-doped (DPD) GaAs MESFET grown by organometallic vapor phase epitaxy (OMVPE) are reported. The electron mobility of a DPD structure with a carrier concentration of 3×10¹⁸/cm³ was 2000 cm²/V-s, which is about 20% higher than that of a pulse-doped (PD) structure. Implementing the DPD structure instead of the conventional PD structure as a GaAs MESFET channel, the drain breakdown voltage, current gain cutoff frequency, and maximum stable gain (MSG) increase. The maximum transconductance of 265 mS/mm at a drain current density of 600 mA/mm, a current gain cutoff frequency of 40 GHz, and an MSG of 11 dB at 18 GHz were obtained for a 0.3 μm n⁺ self-aligned DPD GaAs MESFET     

High-quality two-dimensional electron gas inAlxGa1-xAs/GaAs heterostructures by LP-OMVPE

A combination of high mobility and high sheet carrier density in Al_xGa_1-xAs/GaAs two-dimensional electron gas (2DEG) elements was obtained by low-pressure organometallic vapor phase epitaxy (OMVPE). The sheet charge densities (n_s) and mobilities (μ) at 77 K are 1.2×10¹²/cm² and 90000 cm²/V-s for single-channel, and 2.0× 10¹²/cm² and 64500 cm²/V-s for double-channel elements, respectively. Strong correlations between the photoluminescence spectrum of the Al_xGa_1-xAs layers and the 2DEG mobility were found. The 2DEG elements were used as mixers and detectors at millimeter wavelengths. Mixing at 94 GHz with a 1.7-GHz IF bandwidth and detection of signals as high as 238 GHz under a magnetic field were achieved with these devices     

Metamorphic AlInAs/GaInAs HEMTs on GaAs Substrates by MOCVD

Metamorphic AlInAs/GaInAs high-electron mobility transistors with very good device performance have been grown by metal-organic chemical vapor deposition (MOCVD), with the introduction of an effective multistage buffering scheme. Measured room-temperature Hall mobilities of the 2-DEG were over 8000 cm²/V ldr s with sheet carrier densities larger than 4 times 10¹² cm^-2. Transistors with 1-mum gate length exhibited transconductance up to 626 mS/mm. The unity current gain cutoff frequency f_T and the maximum oscillation frequency f_max were 39.1 and 71 GHz, respectively. These results are very encouraging toward the manufacturing of metamorphic devices on GaAs substrates by MOCVD.     

DC and RF performance of LP-MOCVD grownAl0.25Ga0.75As/InxGa1-xAs(x=0.15-0.28) P-HEMT's with Si-delta doped GaAs layer

Si-delta-doped Al_0.25Ga_0.75As/In_xGa_1-xAs (x=0.15-0.28) P-HEMT's, prepared by LP-MOCVD, are investigated. The large conduction band discontinuity leads to 2-DEG density as high as 2.1×10¹²/cm² with an electron mobility of 7300 cm²/V·s at 300 K. The P-HEMT's with 0.7×60 μm gate have a maximum extrinsic transconductance of 380 mS/mm, and a maximum current density of 300 mA/mm. The S-parameter measurements indicate that the current gain and power gain cutoff frequencies are 30 and 61 GHz, respectively, The RF noise characteristics exhibit a minimum noise figure of 1.2 dB with an associated gain of 10 dB at 10 GHz. Due to the efficient doping technique, the electron mobility and transconductance obtained are among the best reported for MOCVD grown P-HEMT's with the similar structure     

High-transconductance insulating-gate InP/InGaAs buried p-bufferDH-MODFETs grown by MOVPE

Buried p-buffer double heterostructure modulation-doped field-effect transistors (BP DH-MODFETs) with an InGaAs quantum-well channel were fabricated with high transconductance and good breakdown voltage, by placing the metal gate directly on Fe-doped InP insulating layer. Excellent extrinsic DC transconductance of 560 mS/mm and a high gate-to-drain diode breakdown voltage (greater than 20 V) were achieved at room temperature with FETs of 1.2-μm gate length. Unity currently gain cutoff frequency f_T of 24 GHz and maximum oscillation frequency f_max of 60 GHz were demonstrated for a drain to source voltage V_DS=4 V, which corresponds to an average electron velocity of 2.2×10⁷ cm/s in the quantum well