双温低品位热驱动新型吸收制冷循环性能

针对传统低品位热驱动CO₂-离子液体制冷系统的制冷效率低等缺陷,从吸收制冷循环基本原理和能量梯级利用原理出发,提出一种双低品位热驱动CO₂-[emim][Tf₂N]吸收制冷系统。为了测试新系统性能,自行搭建双低品位热驱动CO₂-[emim][Tf₂N]吸收制冷实验装置。在定流量的实验条件下进行新系统性能的实验研究。实验结果表明,双低品位热驱动CO₂-[emim][Tf₂N]吸收制冷系统的制冷系数和制冷量随高低温热量比的增大而增大,随高压箱体压力和冷却水入口温度的升高而降低,新系统可制取高品位冷量,还具有较高的效率,制冷效率提高将近50%左右。     

咪唑类离子液体对苯系挥发性有机物脱除性能的研究

为研究咪唑类离子液体吸收甲苯的性能,考察了甲苯体积分数、吸收温度、N₂进气速度和离子液体流量等对吸收甲苯性能的影响,并评价了离子液体的再生性能。结果表明,[Emim][Tf₂N]、[Bmim][Tf₂N]和[Omim][Tf₂N]这3种离子液体对甲苯的吸收率均在90%以上,且阳离子碳链越长,对甲苯的吸收率越高,3种离子液体对甲苯的吸收率大小为:[Omim][Tf₂N]>[Bmim][Tf₂N]>[Emim][Tf₂N]。甲苯体积分数为3 113μL/L、N₂进气速度为50 mL/min、离子液体流量为15 mL/min和吸收温度为20℃的条件下,离子液体对甲苯的吸收率最高。离子液体在140℃、5 066 Pa下干燥再生5次后性能基本稳定。     

[Bmim][BF4]/MEA混合水溶液吸收CO2的吸收性能与液液分相机理

对液液两相CO₂吸收剂1-丁基-3-甲基咪唑四氟硼酸盐（[Bmim][BF₄]）/乙醇胺（MEA）混合水溶液吸收性能进行了实验测定,研究了离子液体[Bmim][BF₄]的引入对吸收性能和液液分相的影响,并通过定量碳谱核磁共振法对分相机理和各相中的物质分布进行分析。研究结果表明,一定配比的[Bmim][BF₄]/MEA混合水溶液吸收CO₂之后会出现互不相溶的液液两相,这种现象伴随着CO₂产物的富集;导致液液分相的原因是氨基甲酸盐浓度的增大;随着[Bmim][BF₄]质量分数的增大,溶液吸收速率呈现出先增大后减小的趋势;分层后H₂O主要分布在富液相,[Bmim][BF₄]主要分布在贫液相,H₂O的质量分数直接影响分层后富液相的传质性能。     

离子液体支撑液膜的CO2/CH4分离性能

由于离子液体对CO₂具有较好的溶解选择性,离子液体支撑液膜分离CO₂越来越受到关注。比较了含3种不同阴离子的常规离子液体([bmim][BF₄]、[bmim][PF₆]、[bmim][Tf₂N])作为支撑液膜的液膜相分离CO₂/CH₄的性能,考察了咪唑环上烷基链长对离子液体支撑液膜性能的影响。考虑向离子液体中引入胺基和羧基等亲CO₂基团,制备了1-丁基-3-甲基咪唑丙氨酸离子液体([bmim][β-Ala]),考察了 [bmim][β-Ala]支撑液膜分离CO₂/CH₄的性能,并对在CO₂渗透测试前后的支撑液膜进行了FT-IR分析,发现氨基酸离子液体中的-NH₂和CO₂的较强作用以及该离子液体的高黏性影响了CO₂的透过性,使[Bmim][β-Ala]支撑液膜的CO₂透过率低。     

Electrical conductivities for four ternary electrolyte aqueous solutions with one or two ionic liquid components at ambient temperatures and pressure

Thiswork provides amethod to explore the transport property of the electrolyte aqueous solutionswith one or two ionic liquids, especially focus on their electrical conductivity. The conductivities were measured for the ternary systems NaCl–[C₆mim][Cl] (1-hexyl-3-methylimidazolium chloride)–H₂O, [C₆mim][BF₄]–[C₆mim][Cl]–H₂O, NaNO₃–[C₆mim][BF₄](1-hexyl-3-methylimidazolium tetrafluoroborate)–H₂O, and [C₄mim][BF₄] (1-butyl-3- methylimidazolium tetrafluoroborate)–[C₆mim][BF₄]–H₂O, and their binary subsystems NaNO₃–H₂O, NaCl–H₂O, [C₆mim][BF₄]–H₂O, [C₆mim][Cl]–H₂O, and [C₄mim][BF₄]–H₂O, respectively. The conductivities of the ternary systems were also determined using generalized Young's rule and semi-ideal solution theory in terms of the data of their binary solutions. The comparison showed that the two simple equations provide good predictions for conductivity of mixed electrolyte solutions and the mixed ionic liquid solutions based on the conductivity of their binary subsystems.     

离子液体[bmim][Tf2N]的分子动力学模拟

建立了离子液体1-正丁基3-甲基咪唑双（三氟甲基磺酰基）酰亚胺（[bmim][Tf₂N]）的全原子模型,并分别在五种不同的温度和五种不同的压力下对其进行了分子动力学模拟。将[bmim][Tf₂N]密度的模拟结果与实验结果进行了比较,两者吻合良好,验证了模型准确性。此外,还对[bmim][Tf₂N]内部的相互作用能随温度和压力的变化规律进行了分析,结果表明：离子液体内部的库仑能、范德华能、长程作用能均随温度的升高而增加,系统达到平衡所需时间随之变短;相对温度而言,压力对离子液体内部相互作用能的影响较小;在各种相互作用能中,范德华能随温度和压力的变化最大;温度和压力对离子液体的构型不会产生影响。     

固载氨基化离子液体的制备及其对CO2的吸附性能

利用浸渍法将[NH₃P-mim][BF₄]和[MEA]L两种离子液体负载到AC、Al₂O₃和MCM-41上,考察了对CO₂的吸附性能,确定了[NH₃P-mim][BF₄]/AC对CO₂的吸附性能最优。并对[NH₃P-mim][BF₄]/AC考察了不同负载量、不同温度下对CO₂的吸附性能,确定了固载离子液体对CO₂的吸附容量随着负载量的增加而增加,且30℃是固载离子液体吸附CO₂的最佳温度,吸附容量达到0.063 mmol CO₂·(g SILP)^-1。对[NH₃P-mim][BF₄]/AC进行红外和热重两种表征,确定了负载离子液体的结构以及在50℃以下优良的热稳定性。     

CO2跨临界喷射制冷循环计算分析

目前还很少有关于CO₂跨临界喷射式制冷循环的研究。本文对CO₂跨临界喷射制冷循环建立了热力学模型,计算了在不同的冷却压力、冷却器出口温度、加热器压力、加热器出口温度及蒸发温度下,喷射器的喷射系数、跨临界喷射制冷循环性能系数(COP)和有效性能系数(COP_m)的变化趋势。结果表明:随着冷却器压力的升高,喷射器的喷射系数减小,循环的COP 和COP_m值先增大后减小,在某个冷却压力下存在最优值;提高冷却器的出口温度,循环的COP 和COP_m值均降低;提高加热器压力、加热器出口温度及蒸发温度均能增大喷射器的喷射系数和循环的COP_m值。     

功能型离子液体的合成表征及CO2吸收性能

合成了两种传统型离子液体［bmim］BF₄和［emim］BF₄及含有胺基和羟基的功能型离子液体［NH₂P-mim］Br、［NH₂-e-mim］BF₄、［OH-e-mim］Br,并对合成的离子液体进行IR和¹H NMR表征。常温常压条件下,对所合成的离子液体开展CO₂吸收性能实验,发现胺基改性离子液体［NH₂P-mim］Br、［NH₂-e-mim］BF₄和羟基改性离子液体［OH-e-mim］Br的CO₂饱和吸收量分别是常规离子液体的3～9倍和1～2倍,且含有乙基官能团的离子液体吸收平衡时间普遍较短。最终探讨了温度、CO₂分压等对功能型离子液体吸收CO₂过程的影响。     

CO2/HCs混合工质亚临界与跨临界循环的性能分析

为了研究CO₂/HCs混合工质应用于热泵系统的性能，建立单级带节流阀亚临界循环和跨临界循环数学模型，分析了CO₂/R170,CO₂/R1270,CO₂/R290,CO₂/RC270 4种混合工质的特性、不同混合工质配比对循环制冷系数COP和高压压力的影响，以及蒸发温度和冷凝温度对循环性能的影响。结果表明：在亚临界循环中，性能最好的是CO₂/RC270,COP_c峰值为2.92,COP_h峰值为3.92,质量比在0.1/0.9左右，COP_c和COP_h分别比其他2种工质高出了9%、26%和7.1%、18%。在跨临界循环中，CO₂/R1270当质量比为0.96/0.04时，COP_c最大值为3.2,COP_h最大值为4.2; CO₂/R290能有效降低高压压力，当循环的高压压力在7.5 MPa下时...     

New process development and process evaluation for capturing CO2 in flue gas from power plants using ionic liquid [emim][Tf2N]

Using the ionic liquid [emim][Tf_2N] as a physical solvent, it was found by Aspen Plus simulation that it was possible to attempt to capture CO_2 from the flue gas discharged from the coal-fired unit of the power plant.Using the combination of model calculation and experimental determination, the density, isostatic heat capacity,viscosity, vapor pressure, thermal conductivity, surface tension and solubility of [emim][Tf_2N] were obtained.Based on the NRTL model, the Henry coefficient and NRTL binary interaction parameters of CO_2 dissolved in[emim][Tf_2N] were obtained by correlating [emim][Tf_2N] with the gas–liquid equilibrium data of CO_2. Firstly,the calculated relevant data is imported into Aspen Plus, and the whole process model of the ionic liquid absorption process is established. Then the absorption process is optimized according to the temperature distribution in the absorption tower to obtain a new absorption process. Finally, the density, constant pressure heat capacity,surface tension, thermal conductivity, and viscosity of [emim][Tf_2N] were changed to investigate the effect of ionic liquid properties on process energy consumption, solvent circulation and heat exchanger design. The results showed that based on the composition of the inlet gas stream to the absorbers, CO_2 with a capture rate of 90% and a mass purity higher than 99.5% was captured. These results indicate that the [emim][Tf_2N] could be used as a physical solvent for CO_2 capture from coal-fired units. In addition, the results will provide a theoretical basis for the design of new ionic liquids for CO_2 capture.     

规整填料塔中离子液体吸收CO2的传质与流体力学性能

在规整填料塔中采用离子液体吸收二氧化碳气体,利用计算流体力学(CFD)软件建立可靠的数学模型,系统考察了离子液体结构及规整填料几何参数对吸收过程的传质特性和流体力学性能的影响规律。结果表明,床层压降随气体流速增大而增大,液相传质系数随液体流速的增大而增大。相同阴离子时,随着阳离子碳链长度的增长,吸收过程压降增大,同时液相传质系数减小。相同阳离子时,不同阴离子的离子液体压降大的同时传质系数也大。但离子液体的结构对压降影响不明显。离子液体筛选主要考虑传质系数和溶解度因素,但二者与离子液体结构表现出相反的规律。两种折线结构的规整填料传质性能优于传统的X型和Y型结构。     

Solubility of CO2 in Methanol, 1-Octyl-3-methylimidazolium Bis(trifluoromethylsulfonyl)imide, and Their Mixtures

Solubility data of carbon dioxide (CO₂) (1) in methanol (2), 1-octyl-3-methylimidazolium bis(trifluoro- methylsulfonyl)imide ([omim]⁺[Tf₂N]^-) (3), and their mixtures (w₃ 0.2, 0.5, and 0.8) at temperatures 313.2 and 333.2 K and pressures up to 7.0 MPa were measured by a high-pressure view-cell technique. The solubility of CO₂ in methanol (w₃=0), [omim]⁺[Tf₂N]^- (w₃=1.0) and their mixtures follows the order of (w₃=0)<(w₃=0.2)< (w₃=0.5)<(w₃=0.8)<(w₃=1.0) at the same temperature and pressure, while the magnitude of Henry's constants follows the reverse order at a given temperature, which is consistent with the COSMO-RS (conductor-like screening for real solvents) calculation. The solubility data of CO₂ in methanol and [omim]⁺[Tf₂N]^- are correlated with the Peng-Robinson equation of state, and the solubility of CO₂ in the mixtures of methanol and [omim]⁺[Tf₂N]^- can be well predicted based on the mole fraction average of methanol and [omim]⁺[Tf₂N]^- over the solubility of CO₂ in pure methanol and [omim]⁺[Tf₂N]^-. The mixtures of methanol and [omim]⁺[Tf2N]^- may be used as physical solvents for capturing CO₂ with high partial pressures since they combine the advantages of organic solvents and ionic liquids.     

[NH2-emim]Br/[Bmim]BF4离子液体中二氧化碳的电化学还原

以2-溴乙胺氢溴酸和N-甲基咪唑盐为原料合成了氨基功能化离子液体1-（2-胺乙基）-3-甲基咪唑溴盐（[NH₂-emim]Br）,用¹H NMR和IR对所制备的离子液体进行了表征,测得25℃下[NH₂-emim]Br的黏度26.691 Pa·s、电导率0.1130 mS·cm^-1,CO₂的溶解饱和度82%（摩尔分数）,将不同含量的[NH₂-emim]Br与[Emim]BF₄、[Bmim]BF₄、[Bmim]PF₆组成二元复合离子液体,并用于CO₂电化学还原研究,循环伏安研究表明,CO₂在[NH₂-emim]Br（0.5%）-[Bmim]BF₄复合离子液体中的还原峰电位较[Bmim]BF₄正移0.4 V,还原峰电流增大9倍,黏度降低为0.08227 Pa·s,电导率增大至1.317 mS·cm^-1,是一种较好的CO₂电化学还原离子液体体系。     

Effects of imidazolium-based ionic liquids on the isobaric vapor–liquid equilibria of methanol + dimethyl carbonate azeotropic systems

The separation of methanol(MeOH) and dimethyl carbonate(DMC) is important but difficult due to the formation of an azeotropic mixture. In this work, isobaric vapor–liquid equilibrium(VLE) data for the ternary systems containing different imidazolium–based ionic liquids(ILs), i.e. MeOH + DMC + 1-butyl-3-methy-limidazolium bis[(trifluoromethyl)sulfonyl]imide([Bmim][Tf_2N]), MeOH + DMC + 1-ethyl-3-methyl-imidazolium bis[(trifluoromethyl)sulfonyl]imide([Emim][Tf_2N]), and MeOH + DMC + 1-ethyl-3-methylimidazolium hexafluorophosphate([Emim][PF6])) were measured at 101.3 kPa. The mole fraction of IL was varied from0.05 to 0.20. The experimental data were correlated with the NRTL and Wilson equations, respectively. The results show that imidazolium-based ILs were beneficial to improve the relative volatility of MeOH to DMC,and [Bmim][Tf_2 N] showed a much more excellent performance on the activity coefficient of MeOH. The interaction energies of system components were calculated using Gaussian program, and the effects of cation and anion on the separation coefficient of the azeotropic system were discussed.     

SEPARATION OF AROMATIC AND ALIPHATIC HYDROCARBONS WITH IONIC LIQUIDS

Naphtha cracker feeds may contain 10-25 wt% aromatic compounds. Removal of these aromatic compounds from the feed to the cracker would offer several advantages: higher capacity, higher thermal efficiency, and less coke formation. In this work, we investigated the separation of toluene from heptane by extraction with ionic liquids.

Several ionic liquids are suitable for extraction of toluene from toluene/heptane mixtures. The selectivities for the aromatic/aliphatic hydrocarbon separation with all ionic liquids tested increase with decreasing aromatic content in the feed. The toluene/heptane selectivities at 10% toluene in the feed at T = 40°C and 75°C with several ionic liquids ([emim]HSO₄, [mmim] methylsulfate, [emim] ethylsulfate, [bmim]BF₄, [emim] tosylate, [mebupy]BF₄, and [mebupy] methylsulfate) are a factor of 1.5-2.5 higher than those obtained with sulfolane, which is a conventional solvent for the extraction of aromatic hydrocarbons from a mixed aromatic/aliphatic hydrocarbon stream. The three most suitable ionic liquids from the ionic liquids tested for the separation of aromatic and aliphatic hydrocarbons are [mebupy]BF₄, [mebupy]CH₃SO₄, and [bmim]BF₄ and at 75°C also [emim] tosylate. The ionic liquid [mebupy]BF₄ is selected for further testing in our extraction pilot plant.

Because ionic liquids have a negligible vapor pressure, evaporating the extracted hydrocarbons from the ionic liquid phase could achieve the recovery of the ionic liquid. A conceptual process scheme for the extraction has been set up. Preliminary calculations show that both the investment costs and the energy costs will be considerably lower with ionic liquids than with sulfolane as the solvent.     

Lipase-catalyzed Synthesis of Caffeic Acid Phenethyl Ester in Ionic Liquids： Effect of Specific Ions and Reaction Parameters

Caffeic acid phenethyl ester（CAPE） is a rare, naturally occurring phenolic food additive. This work systematically reported fundamental data on conversion of caffeic acid（CA）, yield of CAPE, and reactive selectivity during the lipase-catalyzed esterification process of CA and phenylethanol（PE） in ionic liquids（ILs）. Sixteen ILs were selected as the reaction media, and the relative lipase-catalyzed synthesis properties of CAPE were measured in an effort to enhance the yield of CAPE with high selectivity. The results indicated that ILs containing weakly coordinating anions and cations with adequate alkyl chain length improved the synthesis of CAPE. [Emim][Tf2 N] was selected as the optimal reaction media. The optimal parameters were as follows by response surface methodology（RSM）： reaction temperature, 84.0 °C; mass ratio of Novozym 435 to CA, 14︰1; and molar ratio of PE to CA, 16 ︰ 1. The highest reactive selectivity of CAPE catalyzed by Novozym 435 in [Emim][Tf2 N] reached 64.55%（CA conversion 98.76% and CAPE yield 63.75%, respectively）. Thus, lipase-catalyzed esterification in ILs is a promising method suitable for CAPE production.