Preparation and properties of alkaline anion exchange membrane with semi‐interpenetrating polymer networks based on poly(vinylidene fluoride‐co‐hexafluoropropylene)

Alkaline anion exchange membrane with semi‐interpenetrating polymer network (s‐IPN) was constituted based upon quaternized poly(butyl acrylate‐co‐vinylbenzyl chloride) (QPBV) and poly(vinylidene fluoride‐co‐hexafluoropropylene) [P(VDF‐HFP)]. The QPBV was synthesized via the free radical copolymerization, followed by quaternization with N‐methylimidazole. The s‐IPN system was constituted by melting blend of QPBV and P(VDF‐HFP), and then crosslinking of P(VDF‐HFP). Ion exchange capacity, water uptake, mechanical performance, and thermal stability of these membranes were characterized. TEM showed that alkaline anion exchange membrane exhibited s‐IPN morphology with microphase separation. The fabricated s‐IPN membrane exhibited hydroxide ion conductivity up to 15 mS cm^?1 at 25 °C and a maximum DMFC power density of 46.55 mW cm^?2 at a load current density of 98 mA cm^?2 at 30 °C. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45775.     

Sulfonated poly(ether ether ketone)/epoxy/phenol novolac blend proton‐exchange membranes with low methanol permeability

A crosslinked epoxy [4,4′‐diglycidyl‐(3,3′,5,5′‐tetramethylbiphenyl) epoxy resin (TMBP)], cured by phenol novolac (PN), was introduced into a sulfonated poly(ether ether ketone) (SPEEK) membrane (ion‐exchange capacity = 2.0 mequiv/g) with a casting‐solution, evaporation, and heating crosslinking method to improve the mechanical properties, dimensional stability, water retention, and methanol resistance. By Fourier transform infrared analysis, the interactions between the sulfonic acid groups and hydroxyl groups in the blend membranes were confirmed. The microstructure and morphology of the blend membranes were investigated with atomic force microscopy. As expected, the blend membranes showed excellent mechanical properties, good thermal properties (thermal stability above 200°C), lower swelling ratios (1.4% at 25°C and 7.0% at 80°C), higher water retention (water diffusion coefficient = 9.8 × 10^?6 cm²/s), and a lower methanol permeability coefficient (3.6 × 10^?8 cm²/s) than the pristine SPEEK membrane. Although the proton conductivity of the blend membranes decreased, a higher selectivity (ratio of the proton conductivity to the methanol permeability) was obtained than that of the pristine SPEEK membrane. The results showed that the SPEEK/TMBP/PN blend membranes could have potential use as proton‐exchange membranes in direct methanol fuel cells. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Performances of poly(vinylidene fluoride‐co‐hexafluoropropylene) ultrafiltration membranes modified with poly(vinyl pyrrolidone)

The structure and performance of modified poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVdF‐co‐HFP) ultra‐filtration membranes prepared from casting solutions with different concentrations of poly(vinyl pyrrolidone) (PVP) were investigated in this study. Membrane properties were studied in terms of membrane compaction, pure water flux (PWF), water content (WC), membrane hydraulic resistance ( R _m), protein rejection, molecular weight cut‐off (MWCO), average pore size, and porosity. PWF, WC, and thermal stability of the blend membranes increased whereas the crystalline nature and mechanical strength of the blend membranes decreased when PVP additive concentration was increased. The contact angle (CA) decreased as the PVP concentration increased in the casting solution, which indicates that the hydro‐philicity of the surface increased upon addition of PVP. The average pore size and porosity of the PVdF‐co‐HFP membrane increased to 42.82 Å and 25.12%, respectively, when 7.5 wt% PVP was blended in the casting solution. The MWCO increased from 20 to 45 kDa with an increase in PVP concentration from 0 to 7.5 wt%. The protein separation study revealed that the rejection increased as the protein molecular weight increased. The PVdF‐co‐HFP/PVP blended membrane prepared from a 7.5 wt% PVP solution had a maximum flux recovery ratio of 74.3%, which explains its better antifouling properties as compared to the neat PVdF‐co‐HFP membrane. POLYM. ENG. SCI., 55:2482–2492, 2015. © 2015 Society of Plastics Engineers     

Highly methanol resistant and selective ternary blend membrane composed of sulfonated PVdF‐co‐HFP,sulfonated polyaniline and nafion

Partially sulfonated poly(vinylidene fluoride‐co‐hexafluoro propylene)/partially sulfonated polyaniline (SPVdF‐co‐HFP/SPAni) binary blend membranes have shown promising results in terms of low methanol permeability and high membrane selectivity compared to Nafion‐117 membrane. However, the proton conductivity and IEC of this binary blend membrane was much lower than Nafion‐117. It was found that incorporation of minimal quantity of Nafion within SPVdF‐co‐HFP/SPAni blend membrane at a constituent weight % ratio of SPVdF‐co‐HFP:SPAni:Nafion = 50:40:10 induced significant improvements in ion‐exchange capacity (IEC), proton conductivity and tensile strength over that of the binary blend membrane. In addition, the SPVdF‐co‐HFP/SPAni/Nafion ternary blend membrane exhibited much lower methanol permeability, higher membrane and relative selectivities and comparable IEC to Nafion‐117. In effect, presence of minimal quantity of Nafion induced significant positive attributes to the ternary blend membrane; and assisted in reaching a balance between material cost and properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43294.     

Proton exchange membrane based on crosslinked sulfonated polyphosphazene containing pendent perfluorosulfonic acid groups with sulfonated poly(ether ether ketone)

A series of crosslinked membranes based on new sulfonated polyphosphazene bearing pendent perfluorosulfonic acid groups (PMFP‐g‐PS) and sulfonated poly (ether ether ketone) were prepared and evaluated as proton exchange membranes for direct methanol fuel cells (DMFCs). The structure of PMFP‐g‐PS was characterized by Fourier transform infrared spectroscopy, ¹H and ¹⁹F NMR spectra. In comparison with the pristine PMFP‐g‐PS membrane, the crosslinked membranes showed improved water uptakes and proton conductivities. The methanol permeability values of the membranes were in the range of 1.32 × 10^?7 to 3.85 × 10^?7 cm²/s, which were lower than Nafion 117 (12.1 × 10^?7 cm²/s). The selectivity of all the membranes was much higher compared with Nafion 117. Furthermore, transmission electron microscopy observation revealed that clear phase‐separated structures were well dispersed and connected to each other in the membranes. These membranes displayed high water uptakes and low swelling ratios, high proton conductivities, low methanol permeability values, good thermal, and oxidative stabilities. The results indicate that these membranes are potential candidate proton exchange membrane materials for DMFCs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43492.     

Preparation and characterization of proton exchange membrane based on polyphosphoric acid modified by PVDF‐HFP

A polyphosphoric acid functionalized proton exchange membrane (PEM) was prepared by a ring opening reaction using the epoxycyclohexylethyltrimethoxysilane (EHTMS) and amino trimethylene phosphonic acid (ATMP) as raw materials and was modified by poly(vinylidene fluoride)–hexafluoro propylene (PVDF‐HFP). The structure of the membranes was characterized by Fourier transform infrared and scanning electron microscopy. The X‐ray photoelectron spectroscopy explores the content of the elements in the membrane related to the ion exchange capacity value. The membranes’ properties including water uptake, swelling ratio, proton conductivity, and hydrolysis stability were studied. Performance tests show that when ATMP/EHTMS = 1/5, conductivity of the PVDF‐HFP modified PEMs increased from 0.83 × 10^?4 S cm^?1 at 20 °C to 9.53 × 10^?3 S cm^?1 at 160 °C, the swelling ratio of membranes decreased from 2.71% to 2.13%. The results indicate that the introduction of F atoms is beneficial to increase the proton conductivity and the dimensional stability. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46737.     

Solution blown sulfonated poly(ether sulfone)/poly(ether sulfone) nanofiber‐Nafion composite membranes for proton exchange membrane fuel cells

A composite membrane of sulfonated poly(ether sulfone) (SPES)/poly(ether sulfone) (PES) nanofiber (NF) mat impregnated with Nafion was prepared and evaluated for its potential use as a proton conductor for proton exchange membrane (PEM) fuel cells. The supporting composite nanofibrous mat was prepared by solution blowing of a mixture of SPES/PES solution. The characteristics of the SPES/PES NF and the composite membrane, such as morphology, thermal stability, and performance of membrane as PEMs, were investigated. The performance of composite membranes was compared with that of Nafion117. The introduction of solution blown NFs to composite membranes modestly improved proton conductivity, water swelling, and methanol permeability. Therefore, composite membrane containing SPES/PES NFs can be considered as a novel PEM for fuel cell applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42572.     

Novel membranes based on poly(5‐(methacrylamido)tetrazole) and sulfonated polysulfone for proton exchange membrane fuel cells

Proton‐exchange membrane fuel cells (PEMFC)s are increasingly regarded as promising environmentally benign power sources. Heterocyclic molecules are commonly used in the proton conducting membranes as dopant or polymer side group due to their high proton transfer ability. In this study, 5‐(methacrylamido)tetrazole monomer, prepared by the reaction of methacryloyl chloride with 5‐aminotetrazole, was polymerized via conventional free radical mechanism to achieve poly(5‐(methacrylamido)tetrazole) homopolymer. Novel composite membranes, SPSU‐PMTetX, were successfully produced by incorporating sulfonated polysulfone (SPSU) into poly(5‐(methacrylamido)tetrazole) (PMTet). The sulfonation of polysulfone was performed with trimethylsilyl chlorosulfonate and high degree of sulfonation (140%) was obtained. The homopolymers and composite membranes have been characterized by NMR, FTIR, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). ¹H‐NMR and FTIR confirmed the sulfonation of PSU and the ionic interaction between sulfonic acid and poly(5‐(methacrylamido)tetrazole) units. TGA showed that the polymer electrolyte membranes are thermally stable up to ～190°C. Scanning electron microscopy analysis indicated the homogeneity of the membranes. This result was also supported by the appearance of a single T_g in the DSC curves of the blends. Water uptake and proton conductivity measurements were, as well, carried out. Methanol permeability measurements showed that the composite membranes have similar methanol permeability values with Nafion 112. The maximum proton conductivity of anhydrous SPSU‐PMTet0.5 at 150°C was determined as 2.2 × 10^?6 S cm^?1 while in humidified conditions at 20°C a value of 6 × 10^?3 S cm^?1 was found for SPSU‐PMTet2. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40107.     

Preparation and properties of bisphenol A‐based sulfonated poly(arylene ether sulfone) proton exchange membranes for direct methanol fuel cell

Novel bisphenol A‐based sulfonated poly(arylene ether sulfone) (bi A‐SPAES) copolymers were successfully synthesized via direct copolymerization of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenylsulfone, 4,4′‐dichlorodiphenylsulfone, and bisphenol A. The copolymer structure was confirmed by Fourier transform infrared spectra and ¹H NMR analysis. The series of sulfonated copolymers based membranes were prepared and evaluated for proton exchange membranes (PEM). The membranes showed good thermal stability and mechanical property. Transmission electron microscopy was used to obtain the microstructures of the synthesized polymers. The membranes exhibit increased water uptake from 8% to 66%, ion exchange capacities from 0.41 to 2.18 meq/g and proton conductivities (25°C) from 0.012 to 0.102 S/cm with the degree of sulfonation increasing. The proton conductivities of bi A‐SPAES‐6 membrane (0.10–0.15 S/cm) with high‐sulfonated degree are higher than that of Nafion 117 membrane (0.095–0.117 S/cm) at all temperatures (20–100°C). Especially, the methanol diffusion coefficients of membranes (1.7 × 10^?8 cm²/s–8.5 × 10^?7 cm²/s) are much lower than that of Nafion 117 membrane (2.1 × 10^?6 cm²/s). The new synthesized copolymer was therefore proposed as a candidate of material for PEM in direct methanol fuel cell. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis of microphase‐separated poly(styrene‐co‐sodium styrene sulfonate) membranes using amphiphilic urethane acrylate nonionomers as an reactive compatibilizer

Microphase‐separated poly(styrene‐co‐sodium styrene sulfonate) random copolymer (PSSU) membranes were fabricated through a new copolymerization process. Two immiscible monomers, styrene and sodium styrene sulfonate were dissolved in a single solvent and formed homogeneous solutions, which were directly converted to wall‐to‐wall membranes via radical copolymerization process with microphase separation. Since urethane acrylate nonionomer (UAN) chain has amphiphilicity as well as reactivity with vinyl monomers, UAN chain could act not only as compatibilizer for polystyrene and poly(sodium styrene sulfonate), but also as macrocrosslinker, which makes it possible for the formation of crosslinked copolymer of two immiscible polymers without macrophase separation. TEM image of the PSSU membranes showed that nanosized hydrophilic domains formed by hydrophilic/hydrophobic microphase separation were dispersed at hydrophobic matrix phase. PSSU membranes fabricated using UAN chain having longer chain length of polyethylene oxide showed bigger size of hydrophilic domains, which was also confirmed by TEM images. Fabricated PSSU membranes showed proton conductivity higher than 10^?2 S/cm and methanol permeability lower than 10^?7 cm²/s of Nafion® 117 membranes. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Synthesis and properties of sulfonated poly(phosphazene)‐graft‐poly(styrene‐co‐N‐benzylmaleimide) copolymers via atom transfer radical polymerization for proton exchange membrane

A series of sulfonated poly(phosphazene)‐graft‐poly(styrene‐co‐N‐benzylmaleimide) (PP‐g‐PSN) copolymers were prepared via atom transfer radical polymerization (ATRP), followed by regioselective sulfonation which occurred preferentially at the poly(styrene‐co‐N‐benzylmaleimide) sites. The structures of these copolymers were confirmed by Fourier transform infrared (FTIR) spectroscopy, ¹H‐NMR, and ³¹P‐NMR, respectively. The resulting sulfonated PP‐g‐PSN membranes showed high water uptakes (WUs), low water swelling ratios (SWs), low methanol permeability coefficients, and proper proton conductivities. In comparison with non‐grafting sulfonated poly(bis(phenoxy)phosphazene) (SPBPP) membrane previously reported, the present membranes displayed higher proton conductivity, significantly improved the thermal and oxidative stabilities. Transmission electron microscopy (TEM) observation showed clear phase‐separated structures resulting from the difference in polarity between the hydrophobic polyphosphazene backbone and hydrophilic sulfonated poly(styrene‐co‐N‐benzylmaleimide) side chains, indicating effective ionic pathway in these membranes. The results showed that these materials were promising candidate materials for proton exchange membrane (PEM) in direct methanol fuel cell (DMFC) applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42251.     

Actual air separation through poly(aniline‐co‐toluidine)/ethylcellulose blend thin‐film composite membranes

Several multilayer thin‐film composite membranes were fabricated of ethylcellulose (EC) and poly(aniline‐co‐ortho‐toluidine) or poly(ortho‐toluidine) blend as selective thin films and three ultrafiltration membranes with a 10‐ to 45‐nm pore size and 100‐ to 200‐μm thickness as porous supports. The relationships between the actual air‐separation performance through the composite membranes and layer number, composition, casting solution concentration of the thin selective film are discussed. The oxygen‐enriched air (OEA) flux through the composite membranes increases steadily with increasing operational temperature and pressure. The oxygen concentration enriched by the composite membranes appears to decrease with operating temperature, but increases with operating pressure. The actual air‐separation property through the composite membranes seems to remain nearly constant for at least 320 days. The respective highest OEA flux, oxygen flux, and oxygen concentration, respectively, were found to be 4.78 × 10⁻⁵ cm³ (STP)/s · cm², 2.2 × 10⁻⁵ cm³ (STP)/s · cm², and 46% across EC/poly(o‐toluidine) (80/20) blend monolayer thin‐film composite membranes in a single step at 20°C and 650 kPa operating pressure. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 458–463, 2000     

Free‐standing hybrid anion‐exchange membranes for application in fuel cells

A series of free‐standing hybrid anion‐exchange membranes were prepared by blending brominated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (BPPO) with poly(vinylbenzyl chloride‐co‐γ‐methacryloxypropyl trimethoxy silane) (poly(VBC‐co‐γ‐MPS)). Apart from a good compatibility between organic and inorganic phases, the hybrid membranes had a water uptake of 32.4–51.8%, tensile strength around 30 MPa, and T_d temperature at 5% weight loss around 243–261°C. As compared with the membrane prepared from poly (VBC‐co‐γ‐MPS), the hybrid membranes exhibited much better flexibility, and larger ion‐exchange capacity (2.19–2.27 mmol g^?1) and hydroxyl (OH^?) conductivity (0.0067–0.012 S cm^?1). In particular, the hybrid membranes with 60–75 wt % BPPO had the optimum water uptake, miscibility between components, and OH^? conductivity, and were promising for application in fuel cells. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Sulfonated poly(bis‐A)‐sulfones as proton exchange membranes for direct methanol fuel cell application

Sulfonated poly(bis‐A)‐sulfone (SPSF) samples were prepared by a mild postsulfonation method using trimethylsilyl chlorosulfonate as sulfonation agent, and their thermal and mechanical properties were evaluated. The serials of SPSF membranes are thermally stable up to 450°C in air. When compared with the poly(bis‐A)‐sulfone membrane, the hydrophilicity and water uptake of the SPSF membranes are enhanced. A microphase‐separated structure comprised of hydrophilic and hydrophobic polymer backbone was observed from atomic force microscopy phase images. The hydrophilic ionic clusters become continuous to form channels when ion exchange capacity (IEC) reached 1.47 mequiv/g. Moreover, the membranes showed very good proton conductivities (20°C, 0.01–0.11 S/cm) and low‐methanol permeability (0.09–3.06 × 10^?6 cm²/s), and the methanol diffusion coefficients were lower than that of Nafion112 (1.35 × 10^?6 cm²/s) with IEC values from 0.70 to 1.47 mequiv/g. However, the Fenton's reagent test revealed that the membranes exhibited very poor oxidation stability, which is the main defect limiting the application of SPSF for proton exchange membranes. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

Sulfonated poly(ether ether ketone)‐induced porous poly(ether sulfone) blend membranes for the separation of proteins and metal ions

Asymmetric ultrafiltration (UF) membranes were prepared by the blending of poly(ether sulfone) (PES) and sulfonated poly(ether ether ketone) (SPEEK) polymers with N,N′‐dimethylformamide solvent by the phase‐inversion method. SPEEK was selected as the hydrophilic polymer in a blend with different composition of PES and SPEEK. The solution‐cast PES/SPEEK blend membranes were homogeneous for all of the studied compositions from 100/0 to 60/40 wt % in a total of 17.5 wt % polymer and 82.5 wt % solvent. The presence of SPEEK beyond 40 wt % in the casting solution did not form membranes. The prepared membranes were characterized for their UF performances, such as pure water flux, water content, porosity, and membrane hydraulic resistance, and morphology and melting temperature. We estimated that the pure water flux of the PES/SPEEK blend membranes increased from 17.3 to 85.6 L m^?2 h^?1 when the concentration of SPEEK increased from 0 to 40 wt % in the casting solution. The membranes were also characterized their separation performance with proteins and metal‐ion solutions. The results indicate significant improvement in the performance characteristics of the blend membranes with the addition of SPEEK. In particular, the rejection of proteins and metal ions was marginally decreased, whereas the permeate flux was radically improved. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Sorption and transport properties of the semi‐interpenetrating network based on crosslinked poly(vinyl alcohol) and poly(styrene sulfonic acid‐co‐maleic anhydride) as proton‐conducting membranes

This study investigates the sorption and transport properties of hydrocarbon membranes based on poly(vinyl alcohol) network and poly(styrene sulfonic acid‐co‐maleic acid) (PSSA‐MA). The water and methanol self‐diffusion coefficients through an 80 wt % PSSA‐MA interpenetrating SIPN‐80 membrane measured 3.75 × 10^?6 and 5.47 × 10^?7 cm²/s, respectively. These results are lower than the corresponding values of Nafion® 115 (8.89 × 10^?6 cm²/s for water and 8.63 × 10^?6 cm²/s for methanol). The methanol permeability of SIPN‐80 membrane is 4.1 × 10^?7 cm²/s, or about one‐fourth that of Nafion® 115. The difference in self‐diffusion behaviors of Nafion® 115 and SIPN‐80 membranes is well correlated with their sorption characteristics. The solvent uptake of Nafion® 115 increased as the methanol concentration increased up to a methanol mole fraction of 0.63, and then decreased. However, the solvent uptake of the SIPN‐80 membranes decreased sluggishly as the methanol concentration increased. The λ values of water and methanol (i.e., λ and λ) in Nafion® 115 are quite close, indicating no sorption preference between water and methanol. In contrast, the λ value is only one‐third λ for a SIPN‐80 membrane. Accordingly, the SIPN membranes are regarded as candidates for direct methanol fuel cell applications. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Modified Sulfonated Poly(ether ether ketone) Based Mixed Matrix Membranes for Direct Methanol Fuel Cells

Mixed matrix membranes based on zeolite 4A‐methane sulfonic acid (MSA)‐sulfonated poly(ether ether ketone) (SPEEK) are evaluated as a potential polymer electrolyte membrane (PEM) for direct methanol fuel cells (DMFCs). Ion‐exchange capacity, sorption of water, and water–methanol mixture, proton conductivity, and methanol permeability for the mixed‐matrix membranes have been extensively investigated. The mixed‐matrix membranes are also characterized for their cross‐sectional morphology, mechanical, and thermal properties. DMFCs employing SPEEK‐MSA (20 wt.%) blend, zeolite 4A (4 wt.%)‐SPEEK‐MSA (20 wt.%) mixed matrix membranes deliver peak power densities of 130 and 159 mW cm^–2, respectively; while a peak power density of only 95 mW cm^–2 is obtained for the DMFC employing pristine SPEEK membrane at 70 °C. The results showed that these SPEEK based mixed matrix membranes exhibit higher DMFC performance and lower methanol permeability in comparison to Nafion‐117 membrane.     

One‐pot synthesized poly(vinyl pyrrolidone‐co‐methyl methacrylate‐co‐acrylic acid) blended with poly(ether sulfone) to prepare blood‐compatible membranes

In this study, a random copolymer of poly(vinyl pyrrolidone‐co‐methyl methacrylate‐co‐acrylic acid) was synthesized via a one‐pot reaction with the reversible addition–fragmentation chain‐transfer method and was then blended with poly(ether sulfone) (PES) to prepare flat‐sheet membranes that were expected to have anticoagulant and antifouling properties. The synthesized copolymer was characterized by Fourier transform infrared (FTIR) and NMR spectroscopy. The molecular weights and molecular weight distributions were determined by gel permeation chromatography. Elemental analysis was used to calculate the molar ratios of vinyl pyrrolidone (VP), methyl methacrylate (MMA), and acrylic acid (AA) in the copolymer. A liquid–liquid phase‐inversion technique was used to prepare the copolymer‐blended PES membranes. X‐ray photoelectron spectroscopy and attenuated total reflectance–FTIR spectroscopy were used to investigate the copolymer on the membrane surfaces. Compared with the pristine PES membrane, the modified PES membranes showed improved hydrophilicity, low hemolysis ratios, decreased protein adsorption, and suppressed platelet adhesion. Furthermore, the thrombin time and activated partial thromboplastin time indicated that the blood compatibility of the modified PES membranes were improved. The results of the 3‐(4,5‐Dimethylthiazol‐2‐yl)‐2,5‐diphenyltetrazolium bromide (MTT) assay and the cell morphology suggested that the cytocompatibility increased. In addition, the modified membranes showed good protein antifouling properties. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4284–4298, 2013     

Effects of crosslinking modification on the O2/N2 separation characteristics of poly(phenyl sulfone)/poly(bisphenol A‐co‐4‐nitrophthalic anhydride‐co‐1,3‐phenylenediamine) blend membranes

A series of blend membranes of poly(phenyl sulfone) (PPSU) with poly(bisphenol A‐co‐4‐nitrophthalic anhydride‐co‐1,3‐phenylenediamine) (PBNPI) were prepared through a solution casting method. This was done to examine the permeation characteristics of oxygen and nitrogen. The effect of the PPSU/PBNPI ratio on the membrane structure and O₂/N₂ separation performance were investigated. The results show that the permeability increased remarkably with the content of PPSU, whereas the selectivity decreased slightly. To enhance the selectivity of O₂/N₂, the blend membranes were further crosslinked with a p‐xylylenediamine agent via the immersion method. According to the Fourier transform infrared analysis, the N? H group was formed on the imide group of PBNPI. Therefore, we suggest that during the crosslinking modification, the PBNPI served as a crosslinkable polymer; this resulted in increased crosslinking efficiency with PBNPI content. The high‐resolution X‐ray diffraction and melting point method results show that crosslinking modification improved the selectivity with an acceptable loss in permeability along with increased crystallinity. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Quaternized poly(2.6 dimethyl‐1.4 phenylene oxide)/polysulfone blend composite membrane doped with ZnO‐nanoparticles for alkaline fuel cells

A series of quaternized poly(2.6 dimethyl‐1.4 phenylene oxide)/polysulfone (QPPO/PSF) blend anion exchange membrane (AEM) were successfully fabricated and characterized for alkaline fuel cell application. Zinc oxide (ZnO) nanoparticles were introduced in the polymer matrix to enhance the intrinsic properties of the AEM. To confirm successful fabrication, Fourier‐transform infrared spectroscopy and nuclear magnetic resonance (¹H‐NMR) were used. The membrane properties were enhanced by the addition of ZnO nanoparticles. The addition of ZnO nanoparticles resulted to a higher ion exchange capacity (IEC) of 3.72 mmol g^?1, increase of ion conductivity (IC) up to 52.34 mS cm^?1 at 80 °C, enhancement of water uptake, and reduced methanol permeability. The QPPO/PSF/2% ZnO composite retained over 80% of its initial IC at room temperature and also retained over 50% of its initial IC at 80 °C when evaluated for alkaline stability. The maximum power output reached for the membrane electrode assembly constructed with QPPO/PSF/2%ZnO was 69 mW cm^?2 at room temperature, which is about three times more than the parent QPPO membrane. The above results indicate that QPPO/PSF/ZnO is a good candidate as an AEM for fuel cell application. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45959.