硫铁共掺TiO2水热合成及其光催化性能的研究

以TiC14为钛源,FeCl3和硫脲为掺杂剂,分别在不同温度下水热反应2h制备硫和铁共掺杂的纳米TiO2,采用XRD、可见分光光度计对样品进行表征,并以在可见光激发下纳米TiO2对甲基橙光催化降解体系评价其光催化活性.结果表明,水热温度在160℃以上时,硫铁的共掺杂能促使锐钛矿晶粒的形成.金红石TiO2与少量的锐钛矿TiO2混合能有效提高光催化性能,其中以水热温度为170℃的共掺样品的催化效果最好.     

S,Fe共掺杂纳米TiO_2的制备及其光催化性能

以水热法制得了S,Fe共掺杂的纳米TiO2光催化剂(TiO2-S-Fe),XRD分析表明,其为锐钛矿晶型,S,Fe掺杂能抑制TiO2粒径的生长;UV-vis漫反射表明,TiO2-S-Fe对可见光吸收增强,吸收带边明显红移;XPS显示S,Fe共掺杂,使得TiO2表面羟基氧含量提高,从而提高催化剂活性;可见光降解甲基橙溶液结果表明,共掺杂样品光催化效果优于单掺样品,S和Fe共掺杂对提高TiO2可见光活性具有协同效应。当Fe3+∶S∶Ti(摩尔比)=0.005∶1∶1,180℃下水热反应3 h时,制得的TiO2-S-Fe可见光催化活性比纯TiO2的活性提高了约10倍。     

Gd,B共掺杂改性TiO_2纳米颗粒的可见光光催化活性

采用溶胶-凝胶法制备了Gd和B共掺杂的TiO2纳米颗粒,研究了TiO2纳米颗粒在可见光下的光催化活性。应用XRD、TEM和UV-Vis等手段对TiO2纳米颗粒的物相、粒径、形貌及光学性能进行了表征。结果表明,掺杂可以抑制TiO2晶粒增长,阻碍TiO2由锐钛矿相向金红石相的转变。紫外-可见吸收光谱显示,共掺杂纳米颗粒在可见光区吸收有较强提高,共掺杂离子以协同作用拓展TiO2光谱响应,使吸收带产生红移,提高光生载流子的分离效率。光催化降解实验表明,共掺杂TiO2纳米颗粒有很高的可见光光催化活性,以500℃热处理的共掺杂摩尔比为0.005 Gd和0.04 B的TiO2纳米颗粒光催化效果最好,在可见光下对甲基橙的降解率为98.9%。     

Gd,B共掺杂改性TiO2纳米颗粒的可见光光催化活性

采用溶胶-凝胶法制备了Gd和B共掺杂的TiO2纳米颗粒,研究了TiO2纳米颗粒在可见光下的光催化活性。应用XRD、TEM和UV-Vis等手段对TiO2纳米颗粒的物相、粒径、形貌及光学性能进行了表征。结果表明,掺杂可以抑制TiO2晶粒增长,阻碍TiO2由锐钛矿相向金红石相的转变。紫外-可见吸收光谱显示,共掺杂纳米颗粒在可见光区吸收有较强提高,共掺杂离子以协同作用拓展TiO2光谱响应,使吸收带产生红移,提高光生载流子的分离效率。光催化降解实验表明,共掺杂TiO2纳米颗粒有很高的可见光光催化活性,以500℃热处理的共掺杂摩尔比为0.005 Gd和0.04 B的TiO2纳米颗粒光催化效果最好,在可见光下对甲基橙的降解率为98.9%。     

Pb2+掺杂TiO2的光催化性能研究

以钛酸丁酯和硝酸铅为原料,用溶胶-凝胶法制备了Pb2+掺杂纳米TiO2粉体,讨论了不同掺杂浓度、不同热处理温度样品在催化降解刚果红染料实验中的光催化活性,分析了Pb2+掺杂TiO2样品的相组成、晶胞参数和晶粒大小对光催化活性的影响.结果表明:Pb2+掺杂能够使锐钛矿向金红石的转变温度向高温方向移动,并且细化了晶粒,实验最佳掺杂浓度为100∶2.0,最佳热处理温度为700℃;Pb2+掺杂的TiO2的锐钛矿相是影响光催化活性的决定性因素.     

铁和镧共掺杂二氧化钛的光催化活性

采用溶胶-凝胶法制备了纯的和铁镧共掺杂的TiO2纳米粒子,对样品进行了X射线和紫外-可见吸收光谱分析。结果表明,500℃煅烧的未掺杂和共掺杂TiO2均呈锐钛矿结构,铁镧共掺杂抑制了TiO2粒径的长大,使TiO2的吸收带边红移且在可见光区的光吸收增强;光催化降解甲基橙表明,未掺杂的TiO2光催化活性高于P25,而适量铁镧共掺杂TiO2光催化活性进一步得到提高,最佳掺杂比是0.05%的Fe和0.5%的La。     

掺Fe3+纳米TiO2晶体结构及光催化性能研究

采用溶胶-凝胶法制备了纯的和Fe3+掺杂的TiO2纳米粒子,对样品进行了XRD分析,并以甲基橙的光催化降解研究了样品的光催化性能.结果发现Fe3+的掺杂抑制了TiO2粒径的长大,细化了晶粒;Fe3+掺入到TiO2的晶格中,引起了晶格的畸变和膨胀;Fe3+的掺杂促进了TiO2由锐钛矿向金红石的转变;Fe3+的掺杂量和煅烧温度对其光催化性能影响较大,在本实验的条件下,Fe3+的最佳掺杂量为0.05%,最佳煅烧温度为600℃.     

多种光源下氮掺杂TiO_2光催化降解染料废水的研究

以尿素为氮源,采用溶胶-凝胶法制备了氮掺杂纳米TiO2粉末,以甲基橙溶液为模拟染料废水,分别在可见光、模拟太阳光和紫外光条件下,研究了氮掺杂纳米TiO2光催化降解染料废水的性能。结果表明:氮掺杂可以提高TiO2的可见光催化活性;氮含量和煅烧温度对氮掺杂TiO2光催化活性影响较大,n(N)∶n(Ti)为10%且经500℃煅烧的氮掺杂TiO2在可见光和模拟太阳光下均具有最佳的光催化活性;然而在紫外光下,氮掺杂TiO2的光催化活性低于未掺杂的TiO2样品。     

稀土Nd掺杂纳米TiO2的制备及光催化活性探讨

采用溶胶-凝胶法制备了稀土元素Nd掺杂的纳米TiO2光催化剂(Nd-TiO2).通过XRD、SEM、XPS等对Nd-TiO2样品进行了表征和分析,结果表明:稀土Nd掺杂抑制了纳米TiO2晶粒的生长,,提高纳米TiO2的热稳定性并阻碍其由锐钛矿相向金红石相的转变,在界面处形成的Ti-O-Nd键对纳米TiO2粉体的表面化学态和光催化性能产生影响.以甲基橙作为目标降解物,考察了掺杂量、煅烧温度、煅烧时间对催化剂光催化性能的影响,结果表明:当Nd掺杂量为3wt％,在550℃下煅烧4h时,TiO2的催化活性最佳,远远高于P-25的光催化效果.     

掺钇纳米二氧化钛光催化降解甲基橙的研究

采用金属钇掺杂改性,以钛酸四丁酯为主要原料,在室温下,利用溶胶-凝胶法制备了Y3+掺杂纳米TiO2光催化剂,通过X射线衍射分析(XRD)方法分析其改性机制;掺钇纳米TiO2光催化剂经太阳光照射后,用分光光度计测量光催化降解反应后甲基橙溶液浓度的变化,考察其光催化活性;研究了掺杂量和焙烧温度对光催化活性的影响。结果表明,Y3+掺杂能有效地抑制锐钛矿型TiO2向金红石型TiO2的转化,可使纳米TiO2的衍射峰宽化,粒径从80.5 nm降低到42.15 nm,掺杂量为1.2%,焙烧温度在400℃左右时,能够有效地提高TiO2光催化剂光催化活性。     

乙苯,苯乙烯的生产及合成乙苯,苯乙烯催化剂的研究进展

苯乙烯是重要的石油化工原料。本文介绍了国内外苯乙烯生产的发展概况，合成乙苯，苯乙烯所用的催化剂种类，并就苯乙烯生产及催化剂的发展趋势提出了自己的观点。     

Synthesis and characterization of homopolymers and copolymers of various acrylates and acrylonitrile

Various homopolymers and copolymers of methyl acrylate, ethyl acrylate, butyl acrylate, and acrylonitrile in different feed ratios were synthesized. These were characterized by IR, ¹³C-NMR, DSC, DTA, and TGA. Spectroscopic characterization helped in differentiating copolymers of different mol ratios. Thermal analysis revealed different degradation patterns for homopolymers and copolymers. The temperature and energy changes associated with various phase transitions were dependent on the chemical composition of homo- and copolymers, as expected. © 1993 John Wiley & Sons, Inc.     

生物质气化及生物质与煤共气化技术的研发与应用

总结了生物质原料的特点及生物质单独气化的缺点;介绍了国内外生物质气化技术及生物质与煤共气化技术的研发与应用现状;分析了在此领域国内外的发展趋势与前景;概括了开展生物质与煤共气化技术研发的意义。     

Comparison of the Adhesion and Cohesion of Triblock and Random Copolymers of Styrene and Butadiene

A substantially greater detachment energy is required to strip a polyethylene tereph-thalate (Mylar) film from a styrene-butadiene-styrene (SBS) triblock copolymer compared to that for peeling from a random styrene-butadiene (SBR) copolymer. This is true even though the intrinsic interaction between the Mylar and each elastomer is expected to be similar because of their virtually identical chemical composition. It is proposed that this difference in peel strength (between the SBS and SBR) is a consequence of the much higher dissipative capacity of the former elastomer. Another manifestation of this is the higher cohesive tear strength of the SBS compared to the SBR. Extents of energy dissipation within each elastomer during detachment of the Mylar adherend are consistent with the hypothesis that the average maximum stress experience before detachment is some similar fraction of each elastomer's tensile strength.     

责任和责任心的涵义与结构

责任是人应主动承担的角色义务和对其因过失所造成后果应承担的责罚.有两层涵义:一是义务;二是后果.责任心是个体自觉做好分内事务和履行道德义务的心理倾向,是个性心理品质成分中自我特征维度上的重要内容.责任心具有两个方面的涵义:一是角色分内职责;二是角色道德义务.责任心是一种通过责任认知、责任个性和责任适应的动态形式表现出来的静态品质,责任心是责任心过程结构与责任心关系结构相互制约、相互影响的统一体.     

二甲基二烯丙基氯化铵和丙烯酰胺的合成及应用

用复合引发体系(过硫酸盐-偶氮类引发剂)和脂肪胺类氧化还原体系引发,在实验室获得了单体转化率≥98%,特性粘数高于13.6 dL/g的阳离子共聚物PDA,探讨了控制聚合物分子量的影响因素.     

Kinetics and Mechanism of Oxidation of Mono- and Polyacetals

Abstract

Kinetics and mechanisms of oxidation of 6 acetals by molecular oxygen and ozone in liquid phase have been studied. Reaction with molecular oxygen (70°C, 15–16 hr) leads to the formation monoethers of the corresponding glycols with 68–90% selectivity. Salts of metals and complexes with crown-ethers have increased the reaction rate significally. Ozone have reacted with acetals with formation similar products. The mechanisms of intermediate stages have been proposed.     

钾盐资源及钾肥供需情况分析及预测

阐述了国内外钾盐资源及钾肥生产现状,对国内外钾盐的供需形势进行了分析及预测,从资源、原材料、国际市场三方面提出了解决我国钾盐短缺的措施。     

Electronic structures and reactivities of monometallic and bimetallic clusters of Au and Cu

The variation of the Au 4f binding energy of Au clusters with the cluster size has been established by measuring the binding energies of clusters whose size distributions were independently determined by HREM and STM. The binding energy increases significantly when the cluster size is less than 2 nm. Au-Cu bimetallic clusters of the composition Cu₃Au have been deposited for the first time on carbon substrates. The shifts in the core level binding energies of the bimetallic clusters show the effect of alloying in the case of large clusters, but show effects of both alloying and cluster size in the case of the small clusters. The interaction of CO with Cu₃Au clusters is stronger than with a bulk Cu metal. The interaction of CO with small Cu clusters also seems to be stronger than with bulk Cu or with large Cu clusters.     

Wetting properties of homopolymers and copolymers of pentafluorostyrene and methylacrylate and homopolymer blends

Polypentafluorostyrene (PPFS), polymethylacrylate (PMA), and poly(pentafluorostyrene-co-methylacrylate), poly(PFS-co-MA) were prepared and the wetting characteristics of polymer blends of PPFS and PMA were compared with that of poly(PFS-co-MA) via contact angle measurements. The critical surface tension of polypentafluorostyrene was found to be 22.6 dyne/cm, which is comparable to the value reported for polytrifluoroethylene (22 dyne/cm). The critical surface tension of poly(PFS-co-MA) is not linearly related to its composition. The polymer blends of PPFS and PMA exhibit significant surface enrichment of the fluoropolymer. The harmonic-mean method¹ was employed to determine surface tensions of these polymers and many known polymers. It is found that the method produces useful surface tension data provided the contact angle values are derived from testing liquids of dissimilar polarity.