Effects of liquid phases on densification of TiO2-doped Al2O3–ZrO2 composite ceramics

This study investigated the densification behaviors and microstructural evolution of Al₂O₃–ZrO₂ (3Y) composite ceramics doped with four different amounts of TiO₂ (0, 1, 4, and 8 wt%; denoted as 0T, 1T, 4T, and 8T, respectively) to clarify the effect of TiO₂ dopants on densification. The shrinkage rate during densification increased with the increase in the amount of TiO₂. The development of grain boundary feature was also examined. The undoped ceramic showed clean grain boundaries. Thin liquid grain boundary phases were observed in 1T, whereas large liquid phases were found on the grain boundary and at the junction pockets in 4T and 8T. The results were discussed in terms of the relationship between densification and grain boundary feature.     

Comparative Study of Reactive Dyes Oxidation by H2O2/UV,H2O2/UV/Fe2+ and H2O2/UV/Fe° Processes

The decolorization and mineralization of two reactive dyes C.I. Reactive Blue 4 (RB 4) and C.I. Reactive Blue 268 (RB 268) were studied using various advanced oxidation processes (AOPs) such as H₂O₂/UV, H₂O₂/UV/Fe²⁺, and the H₂O₂/UV/Fe°. All processes were performed within a laboratory-scale photo-reactor setup. The experimental results were assessed in terms of absorbance (A) and total organic carbon (TOC) reduction. The main degradation products were identified by high resolution gas chromatography/high resolution mass spectrometry analyses. The results of our study demonstrated that the additions of moderate concentrations of H₂O₂ and Fe catalyst during the AOPs evidently increased the decolorization efficiencies within the first few minutes of the processing time (5–10 min) for both tested dyes, and prolonged irradiation does not necessarily significantly improve decolorization. On contrary, TOC removal rate increased with the processing time and with the addition of the catalyst from 40–50% up to 70–80% at defined experimental conditions. All the tested AOPs were very successful methods for RB 268 decolorization, having very complex structure and much higher molecular weight compared to the dye RB 4. This is important from both economic and ecological points of view.     

Preparation of Ti/Pt/SnO2–Sb2O4 electrodes for anodic oxidation of pharmaceutical drugs

Ti/Pt/SnO₂–Sb₂O₄ electrodes were prepared by alternating Sn and Sb electrodepositions, repeated 4 or 16 times, onto a platinized titanium foil by a thermo-electrochemical method. Chemical, electrochemical, and structural tests have been used for the characterization of Ti/Pt/SnO₂–Sb₂O₄ electrodes. Anodic oxidation of the aqueous solution contaminated by amoxicillin, clofibric acid, diclofenac, and ibuprofen having a concentration of 100 mg L^?1 and 0.035 M of Na₂SO₄ have been applied using Ti/Pt/SnO₂–Sb₂O₄ electrodes at a current density of 10 and 30 mA cm^?2. The chemical oxygen demand removals increased with current density and except for diclofenac, the Ti/Pt/SnO₂–Sb₂O₄ electrode with 4 electrodeposition repetitions gave the best results. The combustion efficiencies for diclofenac and ibuprofen were higher than those obtained with similar electrode material, prepared without platinization, especially in the assay run with Ti/Pt/SnO₂–Sb₂O₄ (16 electrodeposition repetitions).     

Investigation of the effect of ZrO2 and ZrO2/Al2O3 additions on the hot-pressing and properties of equimolecular mixtures of α- and β-Si3N4

In this work, hot-pressing of equimolecular mixtures of α- and β-Si₃N₄ was performed with addition of different amounts of sintering additives selected in the ZrO₂–Al₂O₃ system. Phase composition and microstructure of the hot-pressed samples was investigated. Densification behavior, mechanical and thermal properties were studied and explained based on the microstructure and phase composition. The optimum mixture from the ZrO₂–Al₂O₃ system for hot-pressing of silicon nitride to give high density materials was determined. Near fully dense silicon nitride materials were obtained only with the additions of zirconia and alumina. The liquid phase formed in the zirconia and alumina mixtures is important for effective hot-pressing. Based on these results, we conclude that pure zirconia is not an effective sintering additive. Selected mechanical and thermal properties of these materials are also presented. Hot-pressed Si₃N₄ ceramics, using mixtures from of ZrO₂/Al₂O₃ as additives, gave fracture toughness, K_IC, in the range of 3.7–6.2 MPa m^1/2 and Vicker hardness values in the range of 6–12 GPa. These properties compare well with currently available high performance silicon nitride ceramics. We also report on interesting thermal expansion behavior of these materials including negative thermal expansion coefficients for a few compositions.     

Optical properties of novel oxyfluoride glasses on the systems of LaF3–LaO3/2–NbO5/2 and LaF3–LaO3/2–NbO5/2–AlO3/2

Oxyfluoride glasses of xLaF₃–(60 − x)LaO_3/2–40NbO_5/2 (x = 0, 5, 10, 35) and xLaF₃–(60 − x)LaO_3/2–30NbO_5/2–10AlO_3/2 (x = 0, 10, 20, 30) were prepared using a levitation technique. Both the glass-transition temperature, T_g, and onset crystallization temperature, T_c, were lowered by substituting a part of the oxygen with fluorine in the glasses. An appropriate amount of fluorine maximized the difference between the temperatures, ΔT (= T_c − T_g), indicating the improvement in the glass-forming ability. The atomic packing densities of the glasses were approximately 60%, which gradually increased with the fluorine content. The absorption edge of the glasses shifted toward the shorter wavelength region in the ultraviolet spectra and toward the longer region in the infrared spectra by fluorine substitution. In addition, in one of the oxyfluoride glasses, a wide transparency from 307 nm to 9.2 µm was realized. Furthermore, the glass exhibited superior optical properties, with a combination of a high refractive index, n_d, of 2.020 and low wavelength dispersion, v_d, of 30.1. The effect of fluorine substitution on the n_d and its v_d was analyzed using the Lorentz–Lorenz dispersion formula.     

Effects of Precursors for Preparing Intermediate Layer on the Performance of Ti/SnO2+Sb2O3/PbO2 Anode

The Ti/SnO2+Sb2O3/PbO2 anode with SnO2+Sb2O3 intermediate layer obtained by the polymeric precursor method (PPM) and with the conventional route was studied. The morphology and microstructure of SnO2+Sb2O3 intermediate layer derived from different precursors and the top PbO2 active layer were examined by means of ESEM and XRD. The lifetime and electrocatalytic activity of the anode were also assessed by the cyclic voltammetry and accelerated lifetime test in 1.0 mol/L H2SO4 solution. It was found that precursor solvents affected lifetime, microstructure and morphology of the anode, and had little influence on electrocatalysis activity of the electrodes. The accelerated lifetime of Ti/SnO2+Sb2O3/PbO2 anode with intermediate layer prepared by PPM was 29.5 h in 1.0 mol/L H2SO4 solution, which was respectively about four times and twice that of the anode prepared with ethylene glycol and ethanol. After the anode was subjected to thermal corrosion, the lifetime still reached 27 h in contrast to the others.     

Phase equilibrium of the ternary system of NH4Cl-CaCl2-H2O at 50°C

The equilibrium data on the ternary system of NH₄Cl—CaCl₂—H₂O at 50°C were investigated using the wet-residue method. The experimental results show that there are three pure phase crystal areas of NH₄Cl, 2NH₄Cl·CaCl₂·3H₂O and CaCl·2H₂O, two mixture phase crystal areas of NH₄Cl and 2NH₄Cl·CaCl·3H₂O, and 2NH₄Cl ·CaCl₂·3H₂O and CaCl·2H₂O in the system. A new hydration double salt (2NH₄Cl·CaCl·3H₂O) was found in the ternary equilibrium system for the first time.     

Investigation of phase separation of nano-crystalline anatase from TiO2SiO2 thin film

In this work, a set of SiO₂–TiO₂ mixed oxides was prepared by the polymeric sol–gel route and deposited on glass substrate through the dip coating technique. Then, the effect of different important preparation parameters (sol–gel stabilizers, Ti content, and heat treatment) on the phase separation was investigated. The developed films were heat treated at 500 °C and characterized using TGA/DTA, FTIR, XRD, SEM, and AFM. The results showed that TiO₂ segregation can be controlled by selecting an appropriate composition of diethanolamine (DEA) and methyl methacrylate (MMA) for preparation of polymeric silica–titania sol. Besides, anatase phase in the samples were crystallized without any stabilizers within heat treatment procedure at 500 °C; however, using appropriate composition of DEA and MMA crystallization rate significantly decreased.     

Mechanistic studies of CO2/CH4 reforming over Ni–La2O2/5A

The mechanism of CO₂/CH₄ reforming over Ni–La₂O₃/5A has been studied. The results of the CO₂‐pulsing experiments indicated that the amount of CO₂ converted was roughly proportional to the amount of H present on the catalyst, implying that CO₂ activation could be H‐assisted. Pulsing CH₄ onto a H₂‐reduced sample and a similar sample pretreated with CO₂, we found that CH₄ conversion was higher in the latter case. Hence, the idea of oxygen‐assisted CH₄ dissociation is plausible. The fact that the amount of CO produced in 10 pulses of CO₂/CH₄ was larger than that produced in 5 pulses of CO₂ followed by 5 pulses of CH₄, indicated that CO₂ and CH₄ could activate each other synergistically. In the chemical trapping experiments, following the introduction of CD₃I onto a Ni–La₂O₃/5A sample pretreated with CH₄/CO₂, we observed CD₃COOH, CD₃CHO, and CD₃OCD₃. In the in situ DRIFT experiments, IR bands attributable to formate and formyl were observed under working conditions. These results indicate that formate and formyl are intermediates for syngas generation in CO₂/CH₄ reforming, and active O is generated in the breaking of a C–O bond. Based on these results, we suggest that during CO₂/CH₄ reforming, CO₂ activation is H‐promoted and surface O species generated in CO₂ dissociation reacts with CH_x to give CO. A reaction scheme has been proposed. This revised version was published online in July 2006 with corrections to the Cover Date.     

Dehydrogenation of propane in the presence of N2O over In2O3―Al2O3 mixed oxide catalysts

Dehydrogenation of propane coupled with N₂O over a series of binary In₂O₃―Al₂O₃ mixed oxides was investigated. In contrast to the poor performance for sole N₂O decomposition, a remarkable synergy was identified between N₂O decomposition and propane dehydrogenation. Among the catalysts tested, the In₂O₃―Al₂O₃ sample containing a 20 mol% In₂O₃ showed the highest activity for propane dehydrogenation in the presence of N₂O. Moreover, stability far superior to those of the conventional iron-based materials was observed, attributable to the moderate surface acidity of the In―Al―O composite. The essential role of N₂O is suggested to generate active oxygen species facilitating propane dehydrogenation.     

Study of AC electrical properties of V2O5–P2O5–B2O3–Dy2O3 glasses

The AC conductivity of glass samples of composition 60V₂O₅–5P₂O₅–(35−x)B₂O₃–xDy₂O₃, 0.4≤x≤1.2 has been analyzed. The samples were prepared by the usual melt-quench technique. The prepared compounds were analyzed by X-ray diffraction (XRD) and thermo gravimetric–differential thermal analysis (TG/DTA). The activation energies were evaluated using glass transition temperature (T_g) and peak temperature of crystallization (T_c) from TG/DTA. The dependence of activation energy on composition was discussed. The electrical conductance and capacitance were measured over a frequency range of 20 Hz to 1 MHz and a temperature range of 303–473 K; these reveal semiconducting features based predominantly on an ionic mechanism. The dielectric and complex-impedance response of the sample is discussed. The relaxation time was found to increase with increasing temperature. Jonscher's universal power law is applied to discuss the conductivity. The electrode polarization was found to be negligible and confirmed from electrical modulus.     

Synthesis and characterization of MgAl2O4–ZrO2 composites

Different types of dense 5–97% ZrO₂–MgAl₂O₄ composites have been prepared using a MgAl₂O₄ spinel obtained by calcining a stoichiometric mixture of aluminium tri-hydroxide and caustic MgO at 1300 °C for 1 h, and a commercial yttria partially stabilized zirconia (YPSZ) powder as starting raw materials by sintering at various temperatures ranging from 1500 to 1650 °C for 2 h. The characteristics of the MgAl₂O₄ spinel, the YPSZ powder and the various sintered products were determined by X-ray diffraction (XRD), scanning electron microscopy (SEM), BET surface area, particle size analysis, Archimedes principle, and Vickers indentation method. Characterization results revealed that the YPSZ addition increases the sintering ability, fracture toughness and hardness of MgAl₂O₄ spinel, whereas, the MgAl₂O₄ spinel hampered the sintering ability of YPSZ when sintered at elevated temperatures. A 20-wt.% YPSZ was found to be sufficient to increase the hardness and fracture toughness of MgAl₂O₄ spinel from 406 to 1314 Hv and 2.5 to 3.45 MPa m^1/2, respectively, when sintered at 1600 °C for 2 h.     

Influence of annealing treatment on magnetic properties of Fe2O3/SiO2 and formation of ε-Fe2O3 phase

Magnetic properties of Fe₂O₃/SiO₂ samples were studied after being produced by sol-gel synthesis and formation of ε-Fe₂O₃ polymorph. Samples were thermally treated, using different annealing temperatures and annealing times. The size and morphological characteristics of the iron oxide nanoparticles were examined using a TEM microscope. We used the “ellipticity of shapes”, which is a measure of how much the shape of a nanoparticle differs from a perfect ellipse, in order to quantitatively describe morphological properties of nanoparticles. Coercivity measurements were used to identify and monitor the formation of the epsilon-iron oxide phase during the thermal treatments (annealing). Coercivity values were in the range from 1.2 to 15.4 kOe, which is in accordance with previous experience regarding the existence of ε-Fe₂O₃. We have determined the optimal formation conditions for the ε-Fe₂O₃ polymorph (t=1050 °C for 7 h, H_C=15.4 kOe), as well as the narrow temperature interval (1050–1060 °C) in which the polymorph abruptly vanished (H_C=2300 Oe), on the basis of results of the magnetic properties. The threshold temperature for the ε-Fe₂O₃ phase transformation was measured as 1060 °C. We found that different annealing temperatures and annealing times significantly affected magnetic properties of the examined samples.     

Effects of post-annealing on electrical properties of CuF2·xH2O-doped KNN ceramics for rotary-linear ultrasonic motors

Lead-free (K_0.5Na_0.5)NbO₃ (KNN) ceramics were prepared using a novel sintering aid (CuF₂·xH₂O (x$\approx$2)) to investigate the effects of post-annealing temperature and atmosphere on oxygen vacancies, microstructure, and electrical properties. Post-annealing (K_0.5Na_0.5)NbO₃ +?1.5?mol% CuF₂·xH₂O (KNNCH) ceramics at 800?°C under argon was shown to increase the bulk relative density to 97% through the formation of a homogeneous microstructure with liquid phase. The resulting samples presented the following excellent piezoelectric properties: k_p：34.1% ($\pm \text{2\%}$); k_t：45.3% ($\pm \text{2\%}$); Q_m：3170 ($\pm \text{2\%}$); R_z：8.6?Ω ($\pm \text{3}\text{\%}$); and tan$\delta$：0.1%. Our results clearly demonstrate that annealing under argon can produce oxygen vacancies in ceramics, which has a significant influence on the stability of domain structures of the samples. Piezoelectric motors fabricated using these ceramics achieved a velocity of 4.5?mm/s, vertical velocity of 3.02?·mm/s, and output power of 2.93?mW with a negligible increase in temperature and high stability while driven.     

The effect of Fe-acceptor doping on the electrical properties of Na1/2Bi1/2TiO3 and 0.94 (Na1/2Bi1/2)TiO3–0.06 BaTiO3

Na_1/2Bi_1/2TiO₃ (NBT) based ceramics are amongst the most promising lead-free ferroelectric materials. It was expected that the defect chemistry and the effect of doping of NBT would be similar to that observed for lead based materials, however, acceptor doping does not lead to ferroelectric hardening. Instead, high oxygen ionic conductivity is induced. Nevertheless, for solid solutions with BaTiO₃ (BT), which are more relevant with respect to ferroelectric applications, such a drastic change of electrical properties has not been observed so far. To rationalize the difference in defect chemistry between NBT and its solid solution 94(Na_1/2Bi_1/2TiO₃)–0.06 BaTiO₃ (NBT–6BT) compositions with different concentrations of Fe-dopant were investigated. The study illustrates that the materials exhibit very similar behavior to NBT, and extraordinarily high oxygen ionic conductivity could also be induced in NBT–6BT. The key difference between NBT–6BT and NBT is the range of the dependence of ionic conductivity with dopant concentration. Previous studies of NBT–6BT have not reached sufficiently high dopant concentrations to observe high conductivity. In consequence, the same defect chemical model can be applied to both NBT and its solid solutions. This will help to rationalize the effect of doping on ferroelectric properties of NBT-ceramics and defect chemistry related degradation and fatigue.     

Influences of La and Er on structure and properties of Bi2O3–B2O3 glass

Bi₂O₃·2B₂O₃ glasses doped with La₂O₃ and Er₂O₃ were prepared by the melting-quenching method with AR-grade oxides. IR analysis was used to investigate the glass network structure. The characteristic temperatures including the glass transition temperature (T_g), crystallization temperature (T_p), and melting temperature (T_m) were estimated by DSC. The coefficient of thermal expansion (α), mass density (D), and Vickers hardness (H_v) were also measured. The results show that the basic network structure of Bi₂O₃·2B₂O₃ glasses doped with rare-earth oxides consists of chains composed of [BO₃], [BO₄], and [BiO₆] units. La₂O₃ and Er₂O₃ act as network modifiers. As the doping concentrations of the rare-earth oxides were increased, T_g increased and α decreased, indicating that a more rigid glass was obtained. Er₂O₃ reduces the melting temperature and prevents glass crystallization. La₂O₃ contributes to the improvement of the microhardness of Bi₂O₃·2B₂O₃ glass.     

The influence of In2O3 on electrical characteristics of iron mixed Li2O–PbO–B2O3–SiO2–Bi2O3 multi-component glass system

Glasses of the composition 19Li₂O–20PbO–20B₂O₃–30SiO₂–(10−x) Bi₂O₃–1Fe₂O₃: xIn₂O₃ with six values of x (0 to 5.0) were synthesized. Dielectric properties viz., dielectric constant, ε′(ω), loss, tan δ, ac conductivity, σ_ac, electric modulus, M(ω) over wide ranges of frequency and temperature and also dielectric break down strength have been studied as a function of In₂O₃ concentration. The temperature dispersion of real part of dielectric constant, ε′(ω) has been analyzed using space charge polarization model. The dielectric loss (and also the electric moduli) variation with frequency and temperature exhibited relaxation effects and these effects were attributed to the divalent iron ion complexes. The ac conductivity exhibited maximal effect, whereas the activation energy for the conductivity demonstrated minimal magnitude at about 1.0 mol% of In₂O₃. The conductivity mechanism is understood due to the polaronic transfer between Fe²⁺ and Fe³⁺ ions. The low temperature ac conductivity mechanism is explained following the quantum mechanical tunneling model. Spectroscopic studies viz., optical absorption and ESR spectra have revealed that the redox ratio (Fe²⁺/Fe³⁺) is maximal when the concentration of In₂O₃ is ~1.0 mol%. The higher values of dielectric parameters observed at 1.0 mol% of In₂O₃ are attributed to the presence of iron ions largely in divalent state and act as modifiers. The analysis of these results together with spectroscopic studies has indicated that when In₂O₃ is present in the glass matrix in higher concentrations (more than 1.0 mol%) iron ions predominantly exist in trivalent state, occupy substitutional positions and make the glass more rigid. Such enhanced rigidity of the network is causing the decrease of dielectric parameters with the concentration of In₂O₃. Finally it is concluded that In₂O₃ mostly participate in the glass network in octahedral positions and make act as reducing agent (for iron ions) in the studied glass matrix when its concentration is ≤1.0 mol%.     

Composition of Pd-La/α-Al2O3 catalysts

The objective of this study is to investigate the structure of the Pd-La/-Al₂O₃ catalyst. X-ray diffraction (XRD) and temperature-programmed reduction (TPRd) were used as characterization techniques. Contrary to the assertions in the literature, XRD studies conducted on La/-Al₂O₃ composite oxides and Pd-La/-Al₂O₃ catalysts show that Pd catalyzes the solid state reaction between A1₂O₃ and Al₂O₃ to form LaAlO₃. TPRd studies conducted on Pd/-Al₂O₃, Pd/La₂O₃, Pd/LaAlO₃, and Pd-La/-Al₂O₃ catalysts suggest that Pd in the Pd-La/-Al₂O₃ catalyst interacts more strongly with LaAlO₃ than with -Al₂O₃. Reaction studies were conducted to investigate the activity of Pd/-Al₂O₃, Pd/La₂O₃, Pd/LaA10₃, and Pd-La/-Al₂O₃ catalysts for nitric oxide (NO) reduction. These studies show that Pd/LaAlO₃ catalysts are most active for NO removal at stoichiometric and under net reducing conditions.