Friction and Wear Performance of Boron Doped,Undoped Microcrystalline and Fine Grained Composite Diamond Films

Chemical vapor deposition(CVD) diamond films have attracted more attentions due to their excellent mechanical properties. Whereas as-fabricated traditional diamond films in the previous studies don’t have enough adhesion or surface smoothness, which seriously impact their friction and wear performance, and thus limit their applications under extremely harsh conditions. A boron doped, undoped microcrystalline and fine grained composite diamond(BD-UM-FGCD) film is fabricated by a three-step method adopting hot filament CVD(HFCVD) method in the present study, presenting outstanding comprehensive performance, including the good adhesion between the substrate and the underlying boron doped diamond(BDD) layer, the extremely high hardness of the middle undoped microcrystalline diamond(UMCD) layer, as well as the low surface roughness and favorable polished convenience of the surface fine grained diamond(FGD) layer. The friction and wear behavior of this composite film sliding against low-carbon steel and silicon nitride balls are studied on a ball-on-plate rotational friction tester. Besides, its wear rate is further evaluated under a severer condition using an inner-hole polishing apparatus, with low-carbon steel wire as the counterpart. The test results show that the BD-UM-FGCD film performs very small friction coefficient and great friction behavior owing to its high surface smoothness, and meanwhile it also has excellent wear resistance because of the relatively high hardness of the surface FGD film and the extremely high hardness of the middle UMCD film. Moreover, under the industrial conditions for producing low-carbon steel wires, this composite film can sufficiently prolong the working lifetime of the drawing dies and improve their application effects. This research develops a novel composite diamond films owning great comprehensive properties, which have great potentials as protecting coatings on working surfaces of the wear-resistant and anti-frictional components.     

The influence of surface roughness on friction and wear of machine element coatings

The use of low friction coatings like amorphous carbon or metal-doped carbon coatings on machine elements is constantly increasing. Most often, a surface treatment, e.g. grinding and polishing or honing, is required for optimal performance of the coated machine element. This can be time consuming and costly.In this study, the effect of surface roughness on friction and sliding wear of two different coatings, one tungsten containing and one chromium containing coating, were examined using a ball-on-disc test. Ball bearing steel plates were grinded to different surface roughnesses and coated with the two different coatings.The friction was found to depend on surface roughness where the rougher surfaces gave higher friction coefficients. The wear rate for the a-C:W coating was found to be independent of the roughness, whereas the roughness had a strong influence on the wear rate for the a-C:Cr coating. This could partly be explained by a difference in wear mechanism, where fatigue wear was observed for the a-C:Cr coating but not for the a-C:W coating.     

Ultrananocrystalline Diamond Film as a Wear-Resistant and Protective Coating for Mechanical Seal Applications

Mechanical shaft seals used in pumps are critically important to the safe operation of the paper, pulp, and chemical process industry, as well as petroleum and nuclear power plants. Specifically, these seals prevent the leakage of toxic gases and hazardous chemicals to the environment and final products from the rotating equipment used in manufacturing processes. Diamond coatings have the potential to provide negligible wear, ultralow friction, and high corrosion resistance for the sliding surfaces of mechanical seals, because diamond exhibits outstanding tribological, physical, and chemical properties. However, diamond coatings produced by conventional chemical vapor deposition (CVD) exhibit high surface roughness (R_a ≥ 1 μm), which results in high wear of the seal counterface, leading to premature seal failure. To avoid this problem, we have developed an ultrananocrystalline diamond (UNCD) film formed by a unique CH₄/Ar microwave plasma CVD method. This method yields extremely smooth diamond coatings with surface roughness R_a = 20–30 nm and an average grain size of 2–5 nm. We report the results of a systematic test program involving uncoated and UNCD-coated SiC shaft seals. Results confirmed that the UNCD-coated seals exhibited neither measurable wear nor any leakage during long-duration tests that took 21 days to complete. In addition, the UNCD coatings reduced the frictional torque for seal rotation by five to six times compared with the uncoated seals. This work promises to lead to rotating shaft seals with much improved service life, reduced maintenance cost, reduced leakage of environmentally hazardous materials, and increased energy savings. This technology may also have many other tribological applications involving rolling or sliding contacts.     

Friction and wear of self-mated SiC and Si3N4 sliding in water

The friction and wear of self-mated SiC and Si₃N₄ with different initial roughness sliding in water were investigated with pin-on-disk apparatus at normal load of 5 N and sliding speed of 120 mm/s in ambient condition. It was found that, for self-mated Si₃N₄, the wear mechanism for surface smoothening to obtain low friction was tribochemical wear, but for self-mated SiC, it changed from mechanical wear into tribochemical wear with increasing sliding cycles. After running-in in water, self-mated Si₃N₄ exhibited lower steady-state friction coefficient than self-mated SiC did. For these two ceramics, initial and steady-state friction coefficients were hardly dependent on initial roughness. Initial roughness mainly affected the running-in period. The larger the initial roughness, the longer the running-in period, but the running-in period was much shorter for self-mated Si₃N₄ at each initial roughness than that for self-mated SiC.     

Tribological behavior between micro- and nano-crystalline diamond films under dry sliding and water lubrication

The tribological behavior of micro- and nano-crystalline diamond films is evaluated in dry sliding and water lubricating condition. The main wear mechanism is found to be abrasive wear mode induced by self-polishing. Non-diamond components and higher compressive residual stresses are detected in flat MCD films after dry sliding, in comparison to NCD. Origin of decreased friction coefficient in CVD diamond tribosystems under water lubrication is attributed to the effect of water on the formed graphic material and the chemisorbing of diamond surface with H₂O, hydrogen or hydroxyl ions. For the MCD/NCD or NCD/MCD contact, the surface roughness of ball largely determines the stable friction coefficient in dry sliding, where NCD film usually presents higher wear rate.     

腐蚀介质条件下NiCrBSi/WC喷熔层的摩擦学性能研究

采用氧-乙炔火焰喷熔工艺,制备了碳化钨颗粒增强镍基合金喷熔层(NiCrBSi/WC),研究了它在腐蚀介质条件下的摩擦磨损行为与机理,并考察了载荷、滑动速度对其摩擦磨损性能的影响规律。研究结果表明:NiCrBSi/WC具有良好的耐腐蚀磨损性能,且当WC含量为20%时,腐蚀磨损率最低;WC含量超过20%后,由于喷熔层存在“腐蚀原电池”效应,其腐蚀磨损率增大。NiCrBSi/WC的腐蚀磨损率随载荷增加而变大,随速度增大而减小。载荷的增加使喷熔层的犁削磨损加剧,导致摩擦系数和磨损率增大;速度的增大造成摩擦界面温度上升,可生成摩擦转移膜,从而降低了喷熔层的磨损率。     

Evolution of wear,roughness, and friction of Alloy 600 superalloy surfaces in water-submersed sliding

Self-mated wear and friction of Alloy 600 superalloy was studied in a water-submersed ring-on-rod configuration, loading the side of a 6.35 mm diameter rod across the flat surface of a rotating annular ring of 100 mm outer diameter and 70 mm inner diameter producing two sliding contacts along the ring. Tests were conducted at sliding speeds of 0.178 and 0.330 m/s for sliding distances of 100 m. Normal loads of 51 and 204 N were applied, and initial R_a surface roughnesses of the rings along the sliding direction were either smooth (～0.2 μm) or rough (～7.5 μm). Increased initial ring roughness caused a ～20-fold increase in rod wear at the lighter load, whereas at the heavier load increased initial roughness only caused a ～4-fold increase in wear. At lower initial ring roughness the 4-fold decrease in normal load caused a large (one order-of-magnitude) decrease in rod wear, whereas for rings of higher initial roughness the 4-fold decrease in normal load caused only minor (2-fold or less) decreases in rod wear. Wear during this 100 m sliding distance only experienced a minor effect from the 1.8-fold change in sliding speed, as did friction. In all cases friction coefficient rapidly settled into the range 0.6–0.7, except in the cases of lower load on rings of lower initial roughness where friction coefficient remained above 1 for most of this sliding duration. At this lower load the initial ～0.2 μm rod roughnesses increased to nearly 0.8 μm by the 100 m sliding distance, whereas at the higher load this same sliding distance resulted in roughnesses returning near to the initial 0.2 μm. It was hypothesized more highly loaded cases also went through initial roughening prior to smoothening back to 0.2 μm roughness within the 100 m sliding distance, and given additional sliding the more lightly loaded cases would also experience subsequent smoothening. Increasing sliding distance to 400 m, roughnesses indicated a smoothening back to 0.2 μm level during those lightly loaded tests, with friction coefficient correspondingly dropping from 1 into the 0.6–0.7 range observed in all other cases. Extended sliding to 400 m at light loading against rings of lower initial roughness also allowed a rod wear rate which increased with increased sliding distance to be observed, approaching the same rate observed against initially rough rings within the 100 m sliding distance.     

The effect of phosphating on the friction and wear properties of grey cast iron

The friction and wear resistance of two commercial manganese phosphate coatings have been evaluated. Grey cast iron wear pins were treated by the two processes and were tested by sliding against a steel disc, under both lubricated and dry sliding wear conditions.Phosphating increases the sliding distance to scuffing as well as the scuffing load, whilst marginally reducing the coefficient of friction. No advantage was found in phosphating dry sliding surfaces.Phosphating reduces the likelihood of adhesive wear in marginal or poorly lubricated sliding couples. The choice of phosphate coating is primarily dependent on the surface finish of the sliding counterface; thin coatings are suitable if the counterface is smooth but thicker coatings are superior against rougher surfaces.     

Interface roughness effect on friction map under fretting contact conditions

In many industrial applications where fretting damage is observed in the contact (e.g. rotor/blade, electrical contacts, assembly joint, axe/wheel, clutch) the external loadings or geometry design cannot be changed. Therefore, the surface preparation and finishing process become essential to control and reduce the damage caused by fretting. In this paper, the authors present the experimental study of the initial surface roughness and machining process influence on fretting conditions in both partial and full sliding regimes. Surfaces prepared by milling and smooth abrasive polishing processes have been analysed. The influence of roughness on sliding behaviour and analysis of friction have been reported. Also, the contact pressure influence and qualitative analysis of fretting wear scar have been presented.     

Mechanical and tribological properties of amorphous carbon films

The mechanical and tribological properties of amorphous carbon films have been studied in more detail in recent years because these films (a) can be deposited near room temperature, thus allowing film deposition on common engineering alloys (i.e., aluminum and steel) without altering their mechanical properties, and (b) are smooth and conform to surface roughness of the substrate, thus requiring no post deposition processing. In addition, amorphous carbon films exhibit low unlubricated sliding friction in contact with steel and ceramics which is comparable to that of steel against steel in a lubricated contact. The wear resistance of these films is also better than Ti‐based hard coatings. Further improvement in film tribological properties can be achieved by modifying film chemical composition. Because of these attractive features, amorphous carbon films have been evaluated in several applications including automotive, electronic and biomedical engineering. However, environmental factors such as oxygen and humidity have been found to influence tribological properties significantly. This paper reviews the current understanding of the tribological properties of both hydrogenated and non‐hydrogenated amorphous carbon films, the mechanisms responsible for low friction coefficient and identifies areas that require further research. This revised version was published online in June 2006 with corrections to the Cover Date.     

Influence of Surface Roughness on the Transfer Film Formation and Frictional Behavior of TiC/a-C Nanocomposite Coatings

Influence of surface roughness on the friction of TiC/a-C nanocomposite coatings while sliding against bearing steel balls in humid air was examined by detailed analyses of the wear surfaces and the wear scar on the ball counterparts by atomic force microscopy, optical, and confocal microscopy. It was observed that the surface roughness of the coatings essentially determines the wear behavior of the ball counterpart, which consequently influences the transfer film formation. A rough coating causes abrasive wear of the steel ball during the running-in period, which impedes the formation of a stable transfer film and leads to higher values of coefficient of friction (CoF). Moreover, the CoF does not show a decreasing trend after the running-in period, although the roughness of the coating was greatly reduced. Replacing the worn ball with a new one after the running-in period yields lower CoF values similar to that observed for a smooth coating. In both of the cases, no wear of the steel ball occurs and a stable transfer film forms and effectively covers the contact area. The influence of the wear debris on the formation of the transfer film is also discussed.     

Tribological behaviour of MW PACVD diamond coatings in vibrating contacts

Six diamond coatings were produced by microwave plasma-assisted chemical vapour deposition (MW PACVD) on polished SiC substrates. Process gas pressure and process gas composition were varied systematically, resulting in different coating morphologies, roughnesses and grain sizes. Friction and wear were investigated for unlubricated vibrating contact conditions in air at room temperature. Tribological tests on diamond coatings were performed in a ball-on-disc configuration, with steel balls (100Cr6) and alumina balls acting as counterbodies. For comparison of the tribological performance of the diamond coatings, standard tests were performed with a stroke of 200 μn, a load of 10 N, and a frequency of 20 Hz. The effect of relative humidity (RH) was investigated by testing in dry (3% RH), in normal (50% RH), and in moist air (100% RH), respectively To investigate running-in effects and wear propagation, the test duration (10⁴, 10⁵, and 1.2·10⁶ sliding cycles) was varied. For steel/diamond pairings, high wear at the steel ball and high friction were measured, influenced by roughness and grain size of the diamond coating and by relative humidity. For Al₂O₃ against diamond, a pronounced running-in of friction and wear was found. High friction and high wear at the beginning of each test are followed by a stationary phase with extremely low friction coefficients (⩽ 0.05) and with wear rates below the limit of resolution. This running-in depends on grain size and roughness of the coating, on relative humidity, as well as on the operational parameters. Surface analysis using SEM, EDX, LRS and AFM was conducted, to investigate tribologically induced surface changes.     

Fabrication of a resin-bonded ultra-fine diamond abrasive polishing tool by electrophoretic co-deposition for SiC processing

A resin-bonded ultra-fine diamond abrasive polishing tool is fabricated by electrophoretic co-deposition (EPcD), and the processing performance of the tool is evaluated in this study. The dispersion stability of suspensions is characterized by a laser particle size analyzer and settlement ratio. The cathodic EPcD of composite powder is realized by adding Al³⁺ into the suspension. The sintering temperature of composite coatings is determined by differential thermal analysis/thermogravimetry. The surface morphology of the composite coating is observed under a confocal microscope. Results show that uniform, dense, and smooth coatings with diamond and resin particles distributed homogeneously are obtained from the steel substrate. A large (Φ150 mm) polishing tool with a 20 μm-thick coating is successfully prepared using the above process. A smooth mirror surface of SiC wafer with a nanoscale roughness (4.3 nm) is achieved after processing with the ultra-fine diamond abrasive polishing tool.     

表面粗糙度对边界摩擦与磨损性能的影响

本文实验研究了表面粗糙度对线接触ＧＣｒ１５钢摩擦副的边界摩擦与磨损性能的影响。实验所采用的润滑剂为３０号机械油加１％的硬脂酸。实验结果表明：存在一最佳表面粗糙度级别，在此级别下，摩擦副的边界摩擦系数最小，耐磨性能最好。     

Friction and wear behaviour of hard and superhard coatings at cryogenic temperatures

The work presents data on friction and wear behaviour of pin-on-disc pairs with superhard diamond-like carbon (DLC) coatings and hard coatings of zirconium nitride (ZrN) and titanium nitride (TiN) in liquid nitrogen with loads of 2.5 and 10 N and sliding speed of 0.06 m/s. It is shown that at cryogenic temperatures the friction coefficients of pairs of two types of DLC coatings obtained by vacuum-arc deposition of filtered high-speed carbon plasma fluxes depend to a great deal on the mechanical properties of the coatings defined by predominant sp² or sp³ hybridization of valence electrons. A friction coefficient of 0.76 was observed for friction pairs of superhard (90 GPa) DLC coatings having properties similar to those of diamond. For “softer” DLC coatings of 40 GPa and properties similar to those of graphite the friction coefficient shows lower values (0.24–0.48) dependent on normal load and counterbody material. The DLC coatings obtained by the filtered arc technology exhibit good wear resistance and have strong adhesion to the substrate under friction in liquid nitrogen. With a normal load of 10 N under cryogenic temperature a low wear rate (of the order of 7.2×10⁻⁴ nm/cycle) was found for superhard DLC coatings. The friction coefficient of pairs with hard ZrN and superhard DLC coatings on steel discs was revealed to be linearly dependent on the counterbody material hardness between 20 and 100 GPa. The hardness of the pin was varied by means of depositing TiN or DLC coatings and also by using high-hardness compounds (boron nitride and synthetic diamond). Proceeding this way can be promising since it offers the possibility of creating low-temperature junctions of required friction properties.     

Study of tribological performance of ECR-CVD diamond-like carbon coatings on steel substrates: Part 1. The effect of processing parameters and operating conditions

Diamond-like carbon (DLC) coatings were prepared on AISI 440C steel substrates at room temperature by electron cyclotron resonance chemical vapor deposition (ECR-CVD) process in C₂H₂/Ar plasma. Using the designed Ti/TiN/TiCN/TiC interfacial transition layers, relatively thick DLC coatings (1-2 μm) were successfully prepared on the steel substrates. The friction and wear performance of the DLC coatings was evaluated by ball-on-disk tribometry using a steel counterbody at various normal loads (1-10 N) and sliding speeds (2-15 cm/s). By optimizing the deposition parameters such as negative bias voltage, DLC coatings with hardness up to 30 GPa and friction coefficients lower than 0.15 against the 100Cr6 steel ball could be obtained. The friction coefficient was maintained for 100,000 cycles (∼2.2 km) of dry sliding in ambient environments. In addition, the specific wear rates of the coatings were found to be extremely low (∼10⁻⁸ mm³/Nm); at the same time, the ball wear rates were one order of magnitude lower. The influences of the processing parameters and the sliding conditions were determined, and the frictional behavior of the coatings was discussed. It has been found that higher normal loads or sliding speeds reduced the wear rates of the coatings. Therefore, it is feasible to prepare hard and highly adherent DLC coatings with low friction coefficient and low wear rate on engineering steel substrates by the ECR-CVD process. The excellent tribological performance of DLC coatings enables their industrial applications as wear-resistant solid lubricants on sliding parts.     

Tribological properties of flame sprayed Fe–Ni–RE alloy coatings under reciprocating sliding

Fe–Ni–RE self-fluxing alloy powders were flame sprayed onto 1045 carbon steel. The tribological properties of Fe–Ni–RE alloy coatings under dry sliding against SAE52100 steel at ambient conditions were studied on an Optimol SRV oscillating friction and wear tester in a ball-on-disc contact configuration. Effects of load and sliding speed on tribological properties of the Fe–Ni–RE coatings were investigated. The worn surfaces of the Fe–Ni–RE alloy coatings were examined with a scanning electron microscopy(SEM) and an energy-dispersive spectroscopy(EDS). It was found that the Fe–Ni–RE alloy coatings had better wear resistance than the SAE52100 steel. An adhered oxide debris layer was formed on the worn surface in friction. Area of the friction layer varied with variety of sliding speed, but did not vary with load. The oxide layer contributed to decreased wear, but increased friction. Wear rate of the material increased with the load, but dramatically decreased at first and then slightly decreased the sliding speed. The friction coefficient of the material was 0.40-0.58, and decreased slightly with the load, but increased with sliding speed at first, and then tended to be a constant value. Wear mechanism of the coatings was oxidation wear and a large amount of counterpart material was transferred to the coatings.     

Friction and wear behaviors of MoS2/Zr coated HSS in sliding wear and in drilling processes

MoS2 metal composite coatings have been successful used in dry turning, but its suitability for dry drilling has not been yet established. Therefore, it is necessary to study the friction and wear behaviors of MoS2/Zr coated HSS in sliding wear and in drilling processes. In the present study, MoS2/Zr composite coatings are deposited on the surface of W6Mo5Cr4V2 high speed steel(HSS). Microstructural and fundamental properties of these coatings are examined. Ball-on-disc sliding wear tests on the coated discs are carried out, and the drilling performance of the coated drills is tested. Test results show that the MoS2/Zr composite coatings exhibit decreases friction coefficient to that of the uncoated HSS in sliding wear tests. Energy dispersive X-ray(EDX) analysis on the wear surface indicates that there is a transfer layer formed on the counterpart ball during sliding wear processes, which contributes to the decreasing of the friction coefficient between the sliding couple. Drilling tests indicate that the MoS2/Zr coated drills show better cutting performance compared to the uncoated HSS drills, coating delamination and abrasive are found to be the main flank and rake wear mode of the coated drills. The proposed research founds the base of the application of MoS2 metal composite coatings on dry drilling.     

Effects of particle size, polishing pad and contact pressure in free abrasive polishing

The objective of this research is to better understand the mechanisms of material removal in the free abrasive polishing process. Experiments were carried out to understand the effects of particle size, polishing pad and nominal contact pressure on the wear rate and surface roughness of the polished surface. A theoretical model was developed to predict the relationship between the polishing parameters and the wear rate for the case of hard abrasive particles sandwiched between a soft pad and a workpiece (softer than the abrasive particles). Experimental results and theoretical predictions indicate that the wear rate increases with an increase in particle size, hardness of polishing pad and nominal contact pressure, and with a decrease in elastic modulus of the polishing pad. Surface roughness increases with an increase in particle size and hardness of polishing pad, and nominal contact pressure has little effect on the roughness. A dimensionless parameter, wear index which combines all of the preceding parameters, was introduced to give a semi-quantitative prediction for the wear rate in free abrasive polishing. It is also suggested that when polishing hard material, in order to achieve a high materials removal rate and a smooth surface, it is preferable to use diamond as the polishing particles because of their high deformation resistance.     

基于DMT模型的金刚石表面纳米摩擦学研究

基于DMT接触模型，在理论上计算金刚石表面纳米摩擦的摩擦力和摩擦因数；采用原子力显微镜，以金刚石探针和片状金刚石试件作为摩擦副，在大气环境下分别研究机械抛光和聚焦离子束（FIB）刻蚀的金刚石试件的摩擦学特性，并比较实验结果和DMT接触模型计算结果。结果表明：金刚石试件的摩擦因数均随着载荷的增加而减小，这与以往对金刚石微观摩擦的研究结果相符合；DMT接触模型计算结果与机械抛光表面试验结果吻合较好，而略高于FIB刻蚀表面试验结果，验证了DMT模型在金刚石纳米摩擦研究中的适用性。通过表面粗糙度和碳原子化学状态分析，得出粗糙表面对探针滑动的阻碍作用和FIB刻蚀过程中生产的非晶碳的减摩作用是DMT模型应用于上述2种加工表面产生差异的原因。